Study guide

5.4 Modified USLE (MUSLE) & Single-Storm Sediment Yield

Certified Professional in Erosion and Sediment Control CPESC

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Rules, Regulations & Clean Water Act Framework

1.1 Federal Clean Water Act & NPDES Regulatory Framework 1.2 Construction General Permit (CGP), NOI/NOT & State/Local Jurisdiction 1.3 CWA Sections 401, 404 & Specialized Environmental Laws

2 Chapter 2: Site Assessment, Watershed Delineation & Resource Inventory

2.1 Topographic Analysis, Drainage Areas & Watershed Delineation 2.2 Soil Identification, NRCS Soil Surveys & Hydrologic Soil Groups 2.3 Environmental Site Constraints, Receiving Waters & Sensitive Areas

3 Chapter 3: Site Planning, Construction Sequencing & Hazard Management

3.1 Land Disturbance Minimization & Construction Phasing 3.2 Construction Scheduling, Seasonal Windows & Buffer Zones 3.3 Site Hazard Identification & Clearing/Grading Limits

4 Chapter 4: Soil Erosion Mechanics & Types

4.1 Fundamentals of Erosion & the Sedimentation Cycle 4.2 Mechanics of Water Erosion: Splash, Sheet, Rill & Gully 4.3 Channel, Stream Bank, Shoreline & Wind Erosion

5 Chapter 5: Soil Loss Prediction: USLE, RUSLE & MUSLE

5.1 Universal Soil Loss Equation (USLE/RUSLE) Overview & R-Factor 5.2 Soil Erodibility Factor (K) & Topographic Factor (LS) 5.3 Cover Management Factor (C) & Support Practice Factor (P) 5.4 Modified USLE (MUSLE) & Single-Storm Sediment Yield

6 Chapter 6: Runoff Hydrology & Watershed Modeling

6.1 Hydrologic Cycle, Runoff Generation & Time of Concentration 6.2 The Rational Method (Q = CiA) & Peak Runoff Estimation 6.3 NRCS (SCS) Curve Number Method & Runoff Volume Estimation

7 Chapter 7: Runoff Conveyance & Open Channel Hydraulics

7.1 Manning's Equation & Open Channel Flow Hydraulics 7.2 Temporary Diversion Dikes, Berms & Swales 7.3 Grade Stabilization Structures, Check Dams & Flumes

8 Chapter 8: Soil Preparation, Fertility & Revegetation

8.1 Soil Testing, pH Adjustment & Nutrient Management (N-P-K) 8.2 Soil Amendments, Compost Incorporation & Seedbed Preparation 8.3 Plant Selection: Native vs. Non-Native, Turf vs. Woody, Cool vs. Warm Season 8.4 Seeding Methods, Nurse Crops & Hydroseeding Application

9 Chapter 9: Mulching & Rolled Erosion Control Products (RECPs)

9.1 Mulch Types, Hydraulic Mulches & Bonded Fiber Matrices (BFMs) 9.2 Rolled Erosion Control Products (RECPs): Temporary ECBs 9.3 Turf Reinforcement Mats (TRMs) & Permanent Vegetative Armoring 9.4 Hard Armoring: Riprap, Gabions, Articulated Concrete & Cellular Confinement

10 Chapter 10: Perimeter Sediment Barriers & Filtration Controls

10.1 Silt Fence Design, Trenching, Installation & Maintenance 10.2 Vegetative Buffer Strips, Compost Filter Socks & Fiber Rolls (Wattles) 10.3 Gravel Bag Berms, Sandbag Barriers & Brush Barriers

11 Chapter 11: Storm Drain Inlet Protection & Slope Drains

11.1 Drop Inlet Protection: Silt Fence, Wire Mesh & Manufactured Inserts 11.2 Curb Inlet Protection: Gravel Berms, Filter Socks & Foam Inserts 11.3 Temporary & Permanent Pipe Slope Drains and Subsurface Drains

12 Chapter 12: Sediment Traps, Basins & Active Treatment

12.1 Sediment Traps: Design Criteria, Sizing & Maintenance 12.2 Sediment Basins: Sizing (Volume & Surface Area), Length-to-Width Ratio 12.3 Basin Outflow Structures: Skimmers, Perforated Risers & Baffles 12.4 Chemical Treatment, Flocculants (PAM/Chitosan) & Jar Testing

13 Chapter 13: Non-Sediment Pollution Prevention & Good Housekeeping

13.1 Construction Site Dewatering Operations & Filtration 13.2 Concrete Washout, Masonry & Mortar Waste Management 13.3 Fuels, Petroleum, Hazardous Chemicals & Spill Response 13.4 Stabilized Construction Entrances, Tire Washes & Dust Control

14 Chapter 14: SWPPP Administration, Site Inspections & Ethics

14.1 SWPPP Elements, Site Maps & Plan Amendments 14.2 Construction Inspection Protocols, Schedules & Documentation 14.3 Turbidity Monitoring, Discharge Sampling & Corrective Action Logs 14.4 Field Education, Subcontractor Oversight & CPESC Code of Ethics

5.4 Modified USLE (MUSLE) & Single-Storm Sediment Yield

Key Takeaways Explain This Topic AI

The Modified Universal Soil Loss Equation (MUSLE, Williams 1975) replaces the rainfall erosivity factor (R) with a runoff energy factor 95 × (Q × qp)^0.56 to predict single-storm sediment yield delivered at a watershed outlet rather than annual gross upland erosion.

The runoff energy term couples total storm runoff volume (Q, in acre-feet) and peak discharge rate (qp, in cfs), reflecting that flowing runoff provides both the shear stress to detach soil particles and the transport capacity to deliver them downstream.

The Sediment Delivery Ratio (SDR = Y / A) quantifies the fraction of gross hillslope erosion (A) delivered to a watershed outlet, and systematically decreases as drainage basin area increases (SDR ∝ DA^-0.2) due to expanded deposition opportunities.

Unlike USLE, which requires multiplying gross erosion by an SDR to estimate delivered sediment, MUSLE calculates delivered sediment yield directly because runoff terms inherently account for transport and deposition along flow paths.

MUSLE is the primary engineering method for sizing temporary sediment basins and traps to contain sediment volumes generated by specific regulatory design storm events (e.g., the 10-year, 24-hour storm).

Last updated: September 2026

5.4 Modified USLE (MUSLE) & Single-Storm Sediment Yield

Quick Reference: While USLE and RUSLE predict average annual gross hillslope detachment ( A A A , tons/ac/yr), civil and environmental engineers must size sediment basins, traps, and impoundments for discrete design storm events (e.g., the 2-year or 10-year, 24-hour storm). In 1975, Jimmy R. Williams developed the Modified Universal Soil Loss Equation (MUSLE) by replacing the rainfall energy factor ( R R R ) with a runoff energy factor : Y = 95 × ( Q × q p ) 0.56 × K × L S × C × P Y = 95 \times (Q \times q_p)^{0.56} \times K \times LS \times C \times P Y = 95 × ( Q × q p ​ ) 0.56 × K × L S × C × P . Here, Y Y Y is the single-storm delivered sediment yield in tons , Q Q Q is runoff volume in acre-feet , and q p q_p q p ​ is peak discharge in cfs . Because MUSLE is driven directly by runoff energy, it models delivered sediment at a watershed outfall without requiring a separate Sediment Delivery Ratio ( S D R SDR S D R ) .

Fundamental Limitations of Annual USLE / RUSLE

While USLE and RUSLE serve as indispensable tools for long-term conservation planning and SWPPP erosion risk modeling, they exhibit three critical limitations when applied to civil construction engineering:

Average Annual Time Horizon: USLE/RUSLE yields an annualized erosion rate based on multi-decade meteorological averages. However, construction permits (NPDES Construction General Permits) and municipal engineering codes require designing temporary sediment control structures (sediment basins, sediment traps, sediment barriers) to withstand specific regulatory design storms (e.g., the 10-year, 24-hour storm event).

Rainfall Energy vs. Runoff Realities: In USLE, erosion is driven by rainfall kinetic energy ( R = E I 30 R = EI_{30} R = E I 30 ​ ). However, rainfall does not equal runoff. A massive, high-intensity rainstorm falling upon highly permeable, dry sandy soil or an unpaved gravel pad may generate substantial raindrop splash detachment, but virtually zero surface runoff ( Q = 0 Q = 0 Q = 0 ). In such cases, detached particles simply settle in place a few inches away. Conversely, a moderate rainstorm falling upon saturated clay subsoils or an extensive paved commercial pad generates massive runoff volume and high peak velocity, scouring and transporting enormous sediment volumes off-site.

Gross Detachment vs. Delivered Sediment Yield: USLE predicts gross detachment across hillslope surfaces. It cannot determine how much of that detached soil actually travels through the drainage network to reach a property boundary, a sediment basin inlet, or a receiving stream outfall.

The Williams (1975) Modified USLE (MUSLE) Formulation

To overcome these limitations for hydrological engineering, Jimmy R. Williams (USDA-ARS, Temple, Texas) developed the Modified Universal Soil Loss Equation (MUSLE) in 1975. Williams replaced the rainfall erosivity factor ( R R R ) with an empirical runoff energy term that combines total runoff volume and peak runoff rate.

The MUSLE Equation (U.S. Customary Units) Y = 95 × ( Q × q p ) 0.56 × K × L S × C × P Y = 95 \times (Q \times q_p)^{0.56} \times K \times LS \times C \times P Y = 95 × ( Q × q p ​ ) 0.56 × K × L S × C × P

Where:

Y Y Y = Single-Storm Sediment Yield: Delivered to the watershed or catchment outlet for the specific design storm event, expressed in tons (U.S. short tons = 2 , 000 lbs 2,000\text{ lbs} 2 , 000 lbs ). (Note: Y Y Y represents total mass of delivered sediment, not tons per acre per year).

Q Q Q = Total Runoff Volume: Generated by the contributing drainage basin for the design storm, expressed in acre-feet ( ac-ft \text{ac-ft} ac-ft ). One acre-foot equals 43 , 560 cubic feet 43,560\text{ cubic feet} 43 , 560 cubic feet .

q p q_p q p ​ = Peak Discharge Rate: The crest runoff flow rate exiting the watershed outfall for the design storm, expressed in cubic feet per second ( cfs \text{cfs} cfs ). Typically calculated using the NRCS TR-55 Graphical Peak Discharge method or HEC-HMS hydrologic modeling.

K K K = Soil Erodibility Factor: Area-weighted average soil erodibility factor for the contributing watershed (same standard USLE units).

L S LS L S = Topographic Factor: Representative topographic length and steepness factor for the contributing drainage area.

C C C = Cover Management Factor: Area-weighted cover factor representing site surface stabilization conditions during the design storm.

P P P = Support Practice Factor: Area-weighted conservation/support practice factor.

95 95 95 = Empirical Calibration Coefficient: Dimensional conversion constant for U.S. customary units.

Metric (SI) Formulation

In international and metric engineering applications, the MUSLE equation is written as: Y metric = 11.8 × ( Q m 3 × q m 3 / s ) 0.56 × K × L S × C × P Y_{\text{metric}} = 11.8 \times (Q_{\text{m}^3} \times q_{\text{m}^3/\text{s}})^{0.56} \times K \times LS \times C \times P Y metric ​ = 11.8 × ( Q m 3 ​ × q m 3 / s ​ ) 0.56 × K × L S × C × P

Where Y Y Y is delivered sediment yield in metric tonnes , Q Q Q is runoff volume in cubic meters ( m 3 \text{m}^3 m 3 ), and q p q_p q p ​ is peak discharge in cubic meters per second ( m 3 / s \text{m}^3/\text{s} m 3 / s ). The coefficient 11.8 11.8 11.8 reflects the dimensional unit conversion from the English coefficient 95 95 95 .

Physical Meaning of the Runoff Energy Term ( Q × q p ) 0.56 (Q \times q_p)^{0.56} ( Q × q p ​ ) 0.56

The runoff energy factor fundamentally improves sediment prediction because flowing surface water performs two distinct physical tasks:

Runoff Volume ( Q Q Q , acre-feet): Quantifies the total volumetric mass of water traversing the drainage network. A large runoff volume sustains hydraulic flow depth and flow duration, preventing suspended silt and fine sand particles from settling out along the flow path.

Peak Discharge Rate ( q p q_p q p ​ , cfs): Dictates maximum flow depth, flow velocity, and peak tractive shear stress ( τ = γ R h S \tau = \gamma R_h S τ = γ R h ​ S ) exerted on the soil surface at the crest of the runoff hydrograph. Peak velocity determines the maximum particle size that runoff can detach and transport without deposition.

The Interactive Product ( Q × q p ) (Q \times q_p) ( Q × q p ​ ) : Combines total flow mass and peak hydraulic power. The exponent 0.56 0.56 0.56 reflects the non-linear hydraulic scaling between flow energy and sediment transport capacity.

Zero Runoff Boundary Condition: If a storm produces no surface runoff ( Q = 0 Q = 0 Q = 0 ), the runoff energy term evaluates to zero ( 95 × ( 0 ) 0.56 = 0 95 \times (0)^{0.56} = 0 95 × ( 0 ) 0.56 = 0 ), yielding Y = 0 tons Y = 0\text{ tons} Y = 0 tons . Unlike USLE, MUSLE correctly predicts zero sediment yield when no runoff occurs, regardless of rainfall kinetic energy.

Sediment Delivery Ratio (SDR) & Deposition Mechanics

A central concept in watershed geomorphology and CPESC exam practice is the Sediment Delivery Ratio ( S D R SDR S D R ) . Gross Hillslope Erosion (A) ──► [ Upland Deposition in Swales, Buffers, Flats ] ──► Delivered Sediment Yield (Y)

  • SDR = Y / A (Typically 0.05 to 0.85)
  • Mathematical Definition of SDR

The Sediment Delivery Ratio ( S D R SDR S D R ) is defined as the dimensionless ratio of delivered sediment yield ( Y Y Y ) measured at a designated watershed outlet or property line to the total gross upland hillslope erosion ( A A A ) occurring across the entire contributing watershed: S D R = Y A SDR = \frac{Y}{A} S D R = A Y ​

S D R SDR S D R is expressed as a decimal ( 0.0 to 1.0 0.0\text{ to } 1.0 0.0 to 1.0 ) or as a percentage ( 0 % to 100 % 0\%\text{ to } 100\% 0% to 100% ).

Deposition Along Upland Flow Paths

Gross erosion measures every grain of soil detached on a hillside. However, as sediment-laden sheet flow moves downslope, it encounters changes in terrain. Runoff velocity decelerates whenever:

  • Slope gradient flattens (e.g., at the toe of a cut slope or in broad concave swales);
  • Surface hydraulic roughness ( n n n ) increases (e.g., entering a dense vegetated buffer strip);

Runoff spreads out across wide, shallow overbank areas.

When flow velocity drops below the settling velocity ( v s v_s v s ​ ) of a soil particle (governed by Stokes' Law ), the particle drops out of suspension and deposits on the land surface. Consequently, only a fraction of detached gross erosion ever reaches the watershed outlet.

Watershed Drainage Area Relationship

Empirical research by the USDA-SCS and Vito A. Vanoni demonstrated that S D R SDR S D R decreases systematically as total drainage basin area ( D A DA D A ) increases : S D R = α × ( D A ) − β commonly expressed as S D R = 0.41 × ( D A ) − 0.28 SDR = \alpha \times (DA)^{-\beta} \quad \text{commonly expressed as} \quad SDR = 0.41 \times (DA)^{-0.28} S D R = α × ( D A ) − β commonly expressed as S D R = 0.41 × ( D A ) − 0.28

Where D A DA D A is contributing drainage area in square miles (or acres).

Watershed Drainage Basin Area Typical Sediment Delivery Ratio ( S D R SDR S D R ) Geomorphic & Hydraulic Rationale

Small Construction Site (< 1.0 Acre) 0.70 – 0.90 (70% – 90%) Short, steep flow paths; high channelization; minimal deposition opportunity.

Subdivision Catchment (5 – 20 Acres) 0.45 – 0.65 (45% – 65%) Intermediate flow paths; partial settling in curb gutters, roadside ditches, and flat swales.

Small Agricultural Watershed (100 Acres) 0.30 – 0.40 (30% – 40%) Extensive toe-of-slope deposits, fence-line vegetative filters, and broad grassed waterways.

Sub-Watershed (1.0 Square Mile / 640 Acres) 0.20 – 0.30 (20% – 30%) Meandering channels, active floodplains, and wide riparian wetland zones capture sediment.

River Basin (> 50 Square Miles) 0.05 – 0.15 (5% – 15%) Vast alluvial valley floors, point bars, lakes, and reservoirs trap the vast majority of eroded soil.

Other Factors Governing SDR

Relief-to-Length Ratio ( R / L R/L R / L ): Watersheds with steep vertical relief and short mainstream channel lengths maintain high flow velocities and exhibit significantly higher S D R SDR S D R values.

Drainage Density: Watersheds with highly incised, dense networks of drainage gullies and storm pipes deliver runoff directly to channels without overland filtration, increasing S D R SDR S D R .

Sediment Particle Size Distribution: Coarse sands and gravels deposit almost immediately ( S D R < 0.10 SDR < 0.10 S D R < 0.10 ), whereas colloidal clays and fine silts remain in suspension for days, exhibiting an S D R SDR S D R approaching 1.00 1.00 1.00 .

Core Distinction for the Exam: When using USLE/RUSLE , you must manually multiply gross soil loss ( A A A ) by an empirical S D R SDR S D R to estimate delivered sediment: Y = A × S D R Y = A \times SDR Y = A × S D R . When using MUSLE , you do NOT multiply by an S D R SDR S D R because the runoff energy factor ( 95 ( Q ⋅ q p ) 0.56 95(Q \cdot q_p)^{0.56} 95 ( Q ⋅ q p ​ ) 0.56 ) already accounts for watershed transport efficiency and upland deposition!

Sediment Basin Sizing & Trap Efficiency ( η \eta η )

Under NPDES Phase I and Phase II regulations, temporary sediment basins are mandated for construction drainage areas disturbing 10 or more acres 10\text{ or more acres} 10 or more acres . Sizing these structures requires matching basin volume to incoming design storm sediment yield.

Basin Trap Efficiency ( η \eta η )

The Trap Efficiency ( η \eta η ) of a sediment basin is the percentage of total incoming sediment yield ( Y in Y_{\text{in}} Y in ​ ) that settles out and is retained within the basin pool: η = ( Y trapped Y in ) × 100 \eta = \left( \frac{Y_{\text{trapped}}}{Y_{\text{in}}} \right) \times 100 η = ( Y in ​ Y trapped ​ ​ ) × 100

Trap efficiency is governed by the Camp-Hazen sedimentation model , which depends on the ratio of particle settling velocity ( v s v_s v s ​ ) to basin surface overflow rate ( q / A s q / A_s q / A s ​ ), the basin length-to-width ratio (minimum 2 : 1 2:1 2 : 1 , recommended 4 : 1 4:1 4 : 1 or greater utilizing porous baffles), and the dead storage volume.

Net sediment escaping the basin outfall and entering receiving waters is: Y discharged = Y in × ( 1 − η ) Y_{\text{discharged}} = Y_{\text{in}} \times (1 - \eta) Y discharged ​ = Y in ​ × ( 1 − η )

Converting Sediment Mass ( Y Y Y , tons) to Storage Volume ( V sed V_{\text{sed}} V sed ​ , cubic yards)

To size the physical sediment storage zone (cleanout volume) of an engineered basin, the CPESC practitioner must convert sediment yield mass ( Y Y Y , tons) into physical settled volume: V sed ( cu ft ) = Y ( tons ) × 2 , 000 lbs/ton γ dry ( lbs/cu ft ) V_{\text{sed}} (\text{cu ft}) = \frac{Y (\text{tons}) \times 2,000\text{ lbs/ton}}{\gamma_{\text{dry}} (\text{lbs/cu ft})} V sed ​ ( cu ft ) = γ dry ​ ( lbs/cu ft ) Y ( tons ) × 2 , 000 lbs/ton ​ V sed ( cu yds ) = V sed ( cu ft ) 27 cu ft/cu yd V_{\text{sed}} (\text{cu yds}) = \frac{V_{\text{sed}} (\text{cu ft})}{27\text{ cu ft/cu yd}} V sed ​ ( cu yds ) = 27 cu ft/cu yd V sed ​ ( cu ft ) ​

Where γ dry \gamma_{\text{dry}} γ dry ​ is the settled dry bulk density of deposited sediment, which typically ranges from 65 to 95 lbs/cu ft 65\text{ to } 95\text{ lbs/cu ft} 65 to 95 lbs/cu ft (commonly assumed as 75 lbs/cu ft 75\text{ lbs/cu ft} 75 lbs/cu ft for mixed construction subsoils, or roughly 1.01 tons per cubic yard 1.01\text{ tons per cubic yard} 1.01 tons per cubic yard ).

  • Step-by-Step Worked Calculation: MUSLE Single-Storm Sediment Yield & Basin Sizing
  • Design Problem Scenario

A civil grading contractor is developing a 12.0 -acre 12.0\text{-acre} 12.0 -acre commercial logistics park in suburban Atlanta, Georgia. Local drainage ordinances require the on-site temporary sediment basin to fully contain the sediment volume generated by a 10-year, 24-hour regulatory design storm without exceeding the designated sediment cleanout elevation.

Site Hydrologic Modeling (NRCS TR-55 Method):

  • Design Storm: 10-year, 24-hour rainfall depth = 5.20 inches 5.20\text{ inches} 5.20 inches
  • Total Runoff Volume: Q = 2.50 acre-feet Q = 2.50\text{ acre-feet} Q = 2.50 acre-feet
  • Peak Runoff Discharge Rate: q p = 22.0 cfs q_p = 22.0\text{ cfs} q p ​ = 22.0 cfs

Physical Catchment Parameters:

Area-Weighted Soil Erodibility: K = 0.28 K = 0.28 K = 0.28 (sandy clay loam subsoil)

Representative Topographic Factor: L S = 2.10 LS = 2.10 L S = 2.10 ( 150 ft 150\text{ ft} 150 ft average slope length at 4 : 1 4:1 4 : 1 [ 25 % 25\% 25% ] gradient)

Cover Management Factor: C = 0.35 C = 0.35 C = 0.35 (active grading with temporary hydromulch applied to 40 % 40\% 40% of perimeter areas)

Support Practice Factor: P = 0.90 P = 0.90 P = 0.90 (contour surface roughening / track-walking)

Settled Sediment Dry Density: γ dry = 75.0 lbs/cu ft \gamma_{\text{dry}} = 75.0\text{ lbs/cu ft} γ dry ​ = 75.0 lbs/cu ft

Step 1: Calculate the Runoff Energy Term

Compute the interactive product of runoff volume and peak discharge: ( Q × q p ) = 2.50 ac-ft × 22.0 cfs = 55.0 (Q \times q_p) = 2.50\text{ ac-ft} \times 22.0\text{ cfs} = 55.0 ( Q × q p ​ ) = 2.50 ac-ft × 22.0 cfs = 55.0

Raise the product to the 0.56 0.56 0.56 power: ( 55.0 ) 0.56 = 9.4074 (55.0)^{0.56} = 9.4074 ( 55.0 ) 0.56 = 9.4074

Multiply by the empirical coefficient 95 95 95 : Runoff Energy Factor = 95 × 9.4074 = 893.70 \text{Runoff Energy Factor} = 95 \times 9.4074 = 893.70 Runoff Energy Factor = 95 × 9.4074 = 893.70

Step 2: Compute the Product of Site Specific Factors ( K × L S × C × P K \times LS \times C \times P K × L S × C × P ) K × L S = 0.28 × 2.10 = 0.588 K \times LS = 0.28 \times 2.10 = 0.588 K × L S = 0.28 × 2.10 = 0.588 C × P = 0.35 × 0.90 = 0.315 C \times P = 0.35 \times 0.90 = 0.315 C × P = 0.35 × 0.90 = 0.315 Site Factor Product = 0.588 × 0.315 = 0.18522 \text{Site Factor Product} = 0.588 \times 0.315 = 0.18522 Site Factor Product = 0.588 × 0.315 = 0.18522

Step 3: Compute Delivered Single-Storm Sediment Yield ( Y Y Y ) Y = 893.70 × 0.18522 = 165.53 tons of sediment Y = 893.70 \times 0.18522 = 165.53\text{ tons of sediment} Y = 893.70 × 0.18522 = 165.53 tons of sediment

The 10-year, 24-hour storm will deliver approximately 165.5 tons 165.5\text{ tons} 165.5 tons of eroded sediment into the temporary sediment basin.

Step 4: Convert Sediment Mass to Basin Storage Volume ( V sed V_{\text{sed}} V sed ​ )

Convert sediment tonnage into pounds: Total Mass = 165.53 tons × 2 , 000 lbs/ton = 331 , 060 lbs \text{Total Mass} = 165.53\text{ tons} \times 2,000\text{ lbs/ton} = 331,060\text{ lbs} Total Mass = 165.53 tons × 2 , 000 lbs/ton = 331 , 060 lbs

Compute volume in cubic feet using the dry bulk density of 75.0 lbs/cu ft 75.0\text{ lbs/cu ft} 75.0 lbs/cu ft : V sed = 331 , 060 lbs 75.0 lbs/cu ft = 4 , 414.13 cu ft V_{\text{sed}} = \frac{331,060\text{ lbs}}{75.0\text{ lbs/cu ft}} = 4,414.13\text{ cu ft} V sed ​ = 75.0 lbs/cu ft 331 , 060 lbs ​ = 4 , 414.13 cu ft

Convert cubic feet to cubic yards: V sed = 4 , 414.13 cu ft 27 cu ft/cu yd = 163.49 cu yds ≈ 164 cu yds V_{\text{sed}} = \frac{4,414.13\text{ cu ft}}{27\text{ cu ft/cu yd}} = 163.49\text{ cu yds} \approx 164\text{ cu yds} V sed ​ = 27 cu ft/cu yd 4 , 414.13 cu ft ​ = 163.49 cu yds ≈ 164 cu yds

Engineering Conclusion & Design Specification

To ensure compliance with local sediment retention criteria and prevent premature basin failure during a 10-year storm, the CPESC engineer must specify:

A dedicated sediment storage dead pool volume of at least 4 , 415 cubic feet 4,415\text{ cubic feet} 4 , 415 cubic feet ( 164 cubic yards 164\text{ cubic yards} 164 cubic yards ) below the principal spillway crest or skimmer invert;

A clear sediment cleanout marker stake positioned at the 50 % 50\% 50% storage volume elevation ( 82 cubic yards 82\text{ cubic yards} 82 cubic yards / 2 , 208 cu ft 2,208\text{ cu ft} 2 , 208 cu ft ), mandating mechanical dredging whenever accumulated sediment reaches this marker.

Loading diagram... MUSLE Single-Storm Modeling Mechanics and Basin Sizing Workflow