Study guide

14.5 SPC Charts and Variation Types

APICS CPIM Certified in Planning and Inventory Management Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 ECM 9.0 Domains and Weights 1.3 How to Study for CPIM

2 Supply Chain Strategy Foundations

2.1 Supply Chains, the Environment, and Strategy 2.2 Environment Analysis and Strategic Scope 2.3 Developing and Managing Organizational Strategy 2.4 Competitive Analysis: Five Forces, Benchmarking, and Value Chain

3 Strategy Performance and Operations Choices

3.1 Performance Monitoring and KPIs 3.2 Functional and Operational Strategies 3.3 Environments, Types, and Layouts 3.4 Service Process Design and Product-Process Trade-offs

4 Sales and Operations Planning

4.1 S&OP Purpose and Process 4.2 Aggregate Demand and Supply Plans 4.3 Reconciling S&OP Plans 4.4 Portfolio, New Product Introduction, and Life-Cycle Planning in S&OP 4.5 Strategic Buffers, Bottlenecks, and Capacity-Constrained Resources

5 Plan and Manage Demand

5.1 Demand Management 5.2 Sources of Demand and Forecasting 5.3 Forecast Performance 5.4 Marketing, Promotions, and Product Management 5.5 Qualitative, Associative, and AI-Driven Forecasting

6 Master Scheduling

6.1 Creating the Master Schedule 6.2 Rough-Cut Capacity Planning and MPS Validation 6.3 Using and Maintaining the Master Schedule 6.4 Planning Bills and Two-Level Master Scheduling 6.5 NPI, DFMA, Prototype, and End-of-Life Schedules

7 MRP, CRP, and Supply Disruptions

7.1 Material Requirements Planning 7.2 CRP, Order Promising, and Final Assembly Scheduling 7.3 Changes and Supply Disruptions 7.4 Product Costing and Variance Analysis for Planners

8 External Supply Sources

8.1 Suppliers and Procurement 8.2 Purchasing and Maintenance 8.3 Supply Chain Risk Management 8.4 Sourcing Footprint and Supplier Relationship Types 8.5 Supplier Release Mechanics and Inbound Logistics

9 Sustainability and Reverse Logistics

9.1 Sustainability Strategies 9.2 Waste Hierarchy and Reverse Logistics 9.3 Sustainability Standards, Reporting, and Life-Cycle Assessment

10 Inventory Planning and Costs

10.1 Inventory Planning 10.2 Inventory Costs, Accounting, Costing, and Metrics 10.3 EOQ, Reorder Point, and Safety Stock

11 Inventory Management and Control

11.1 Inventory Management Policies 11.2 Inventory Control 11.3 Service Levels and Inventory Tradeoffs 11.4 MRO Inventory and Maintenance Planning Inputs 11.5 Traceability Standards and Off-Site Inventory

12 Detailed Schedules and PAC

12.1 Planning Detailed Schedules 12.2 Scheduling and PAC Methods 12.3 Creating Production and Service Schedules 12.4 Managing Detailed Schedules and Scheduling Materials 12.5 Sequencing Rules, Lot Splitting, and Overlapped Scheduling 12.6 Capacity Types, Safety Capacity, and Labor Scheduling 12.7 Process Batches, Transfer Batches, and Backflushing

13 Plan and Manage Distribution

13.1 Planning Distribution 13.2 Replenishment and DRP 13.3 Order Management, Trace/Track, and KPIs

14 Quality and Business Investments

14.1 Quality Systems and Tools 14.2 Capital Equipment and Facilities 14.3 Technology in Planning and Inventory 14.4 The Seven Basic and Seven New Quality Tools 14.5 SPC Charts and Variation Types 14.6 Systems Requirements, Master Data, and Emerging Technologies

15 Continuous Improvement

15.1 Continuous Improvement Overview 15.2 Lean, JIT, and the Seven Wastes 15.3 Six Sigma, Kaizen, and Root Cause Tools 15.4 TPM, SMED, Standardized Work, and Visual Management

16 Integration and Exam Readiness

16.1 Planning Hierarchy Integration 16.2 High-Yield Calculations Drill 16.3 Exam Day, Scoring, and Credential Maintenance

14.5 SPC Charts and Variation Types

Key Takeaways Explain This Topic AI

Common-cause variation is inherent, random, and built into the system, so only management changing the process removes it; assignable (special) cause variation is identifiable and external to the normal process, so local action finds and removes it

A process with only common-cause variation is in statistical control, which is stable and predictable but says nothing about capability — in control does not mean capable, and that distinction is a heavily tested trap

Control limits (typically the centre line ±3 sigma) are calculated from the process's own data, while specification limits come from the customer or designer; specification limits never belong on an X-bar chart

X-bar tracks the subgroup average and R tracks the within-subgroup range; read them together and check R first, because the X-bar limits are computed as X-double-bar ± A2 × R-bar

A p chart plots the proportion of defective units while a c chart plots the count of defects per unit or constant area, so one panel with six scratches adds 6 to a c chart but only 1 to a p chart

Last updated: July 2026

Statistical process control (SPC) answers one question before you act: is this variation a signal or is it noise? Adjust a stable process because of a random wiggle and you make it worse — Deming called that tampering , ASCM materials call it over-adjustment, and either way you have added the variation you meant to remove. Ignore a genuine shift and you ship defects. Everything below is machinery for telling those two cases apart.

Two Kinds of Variation

Common cause Assignable (special) cause

Source Inherent in the process design; many small random influences A specific, identifiable event outside the normal process

Pattern Random and stable; predictable within limits A spike, shift, trend, or new pattern

Examples Normal tooling clearance, routine lot-to-lot material spread, ordinary operator variation A worn insert, a new material lot, an untrained operator, a mis-set machine

Who must act Management — only a change to the system changes it Local action — operator, supervisor, or technician finds and removes it

Shorthand The system the workers work in Something that happened to the workers

Hunting a culprit when the variation is common cause is the most common waste in a quality meeting: the process is delivering exactly what it was designed to deliver, and only redesign will change it.

A process showing only common-cause variation is in statistical control — stable and predictable. Now the trap the exam sets repeatedly: in control does not mean capable. A perfectly stable process can be stably, predictably producing scrap if its natural spread is wider than the tolerance or if it sits off-centre. Control describes the voice of the process; capability (Cp and Cpk, section 14.1) describes whether that voice fits inside the customer's specification.

Control Chart Anatomy

Every control chart carries three horizontal references: the centre line (CL) , the average of the plotted statistic; and the upper control limit (UCL) and lower control limit (LCL) , conventionally the centre line ±3 standard deviations of that statistic.

The most-tested fact in this area: control limits are calculated from the process's own data; specification limits come from the customer or the design engineer. Different origins, and no arithmetic connects them. Specification limits therefore never belong on an X-bar chart — comparing a subgroup average against a limit written for individual units is a guaranteed wrong answer. A process can sit inside its control limits and outside spec (stable but incapable), or inside spec and out of control (currently lucky).

The Four Charts the ECM Names

Split on data type first. Variable data is measured on a continuous scale — millimetres, grams, minutes. Attribute data is counted or classified — pass/fail, number of blemishes.

X-bar chart — plots the average of each subgroup of a measured variable, tracking where the process is centred.

R chart — plots the range (largest minus smallest) within each subgroup, tracking spread. Read the pair together, because averaging conceals a widening spread: the subgroup mean holds steady while individual parts scatter further apart. Read R first — the X-bar limits are computed from the average range (X-double-bar ± A2 × R-bar), so an unstable range puts the X-bar limits on a moving foundation.

p chart — plots the proportion (fraction) defective in each sample. Attribute data; sample size may vary, in which case the limits move with n. (The np chart plots the count of defectives when n is constant.)

c chart — plots the count of defects per unit or per constant inspection area. Attribute data with a fixed opportunity size. (The u chart handles defects per unit when the area varies.)

The classic distinction: a p chart counts defective units; a c chart counts defects . One painted panel with six scratches contributes 6 to a c chart but 1 to a p chart — and a panel with a single scratch also contributes 1. "Flaws per panel" wants a c chart; "percentage of panels rejected" wants a p chart.

  • Data you have Question you are asking Correct chart
  • Measurements, taken in subgroups Has the process centre moved? X-bar chart
  • Measurements, taken in subgroups Has the process spread changed? R chart
  • Units classified good or bad What fraction is defective? p chart
  • Defects counted per unit or constant area How many defects per unit? c chart
  • Worked X-bar and R example

Five subgroups of n = 4 fill weights in grams, tolerance 248–252 g:

  • Subgroup Readings Average Range
  • 1 250.2, 249.6, 250.4, 249.8 250.0 0.8
  • 2 249.9, 250.5, 250.1, 249.5 250.0 1.0
  • 3 250.6, 250.2, 249.8, 250.2 250.2 0.8
  • 4 249.6, 250.0, 250.2, 249.8 249.9 0.6
  • 5 251.8, 251.2, 251.6, 251.4 251.5 0.6

Subgroup 1 in full: (250.2 + 249.6 + 250.4 + 249.8) ÷ 4 = 1000.0 ÷ 4 = 250.0 ; range = 250.4 − 249.6 = 0.8 .

Grand mean (X-double-bar) = (250.0 + 250.0 + 250.2 + 249.9 + 251.5) ÷ 5 = 1251.6 ÷ 5 = 250.32 . Average range (R-bar) = (0.8 + 1.0 + 0.8 + 0.6 + 0.6) ÷ 5 = 3.8 ÷ 5 = 0.76 . With the standard factors for n = 4 (A2 = 0.729, D4 = 2.282, D3 = 0):

X-bar chart: UCL = 250.32 + (0.729 × 0.76) = 250.32 + 0.55 = 250.87 ; LCL = 250.32 − 0.55 = 249.77 .

R chart: UCL = 2.282 × 0.76 = 1.73 ; LCL = 0 × 0.76 = 0 .

Every range sits between 0.6 and 1.0, well inside 1.73, so the R chart is in control and the spread is stable . But subgroup 5's average of 251.5 exceeds the X-bar UCL of 250.87 — a special-cause signal . Something moved the process centre without changing its spread, so look for a discrete event between subgroups 4 and 5: a new material lot, a changed setting, a refilled hopper.

Notice what is not true here: every individual reading, 251.8 included, is inside the 248–252 g tolerance. The parts all pass, and the process is still out of control. That is the economic argument for SPC — the chart catches the shift while the parts are still good. One step further: estimated process sigma = R-bar ÷ d2 = 0.76 ÷ 2.059 = 0.369 g, so the natural spread is ±3 × 0.369 = ±1.11 g. Centred at 251.5 the upper tail reaches 252.6 g, past the 252 g upper specification. Left alone, this shift starts making rejects.

Signals beyond a single point outside the limits

A run — seven or more consecutive points on the same side of the centre line (some references use eight). The process has shifted even though no point escaped.

A trend — seven or more consecutive points steadily rising or falling: tool wear, a heating bath, a fouling filter.

Other non-random patterns — cycles, points hugging the centre line, or too many points crowding the limits, which usually means mixed streams or mis-calculated limits.

The Planner's Stake

An out-of-control process is by definition unpredictable, and every planning parameter you own is a prediction. Unstable yield makes the scrap factor in material requirements planning (MRP) a guess; unstable cycle time makes the routing's run and queue times a guess; together they make the promise date a guess. The organization does not absorb that uncertainty for free — it buys protection with safety stock and safety lead time , and both are inventory and cash. When quality reports a critical process out of control, raise buffers temporarily, keep load off that resource in the master schedule, and lower the buffers only after the chart shows the gain held. Quality instability is paid for in inventory.

Exam traps

Control limits are not specification limits, and specification limits never go on an X-bar chart.

In control, capable, and in specification are three separate ideas; a stable process can still be incapable.

Common cause is a management and system responsibility; only a special cause justifies a local hunt.

p charts count defective units ; c charts count defects , so one unit can add several points to a c chart.

Adjusting a stable process because of one unremarkable point is tampering, and it increases variation.