Study guide
3.2 Filters (sand, DE, cartridge)
Certified Pool Operator CPO
Track your progress as you read
Finished sections get a check mark.
1 Introduction, Roles & Regulations
1.1 CPO certification facts, regulations & the operator's role
2 Pool Water Chemistry
2.1 Water balance & the Langelier Saturation Index 2.2 Sanitation & disinfection (chlorine, bromine, breakpoint) 2.3 Chemical testing & alternative sanitizers 2.4 Problem water & chemical-adjustment calculations
3 Pool Equipment
3.1 Pumps & motors 3.2 Filters (sand, DE, cartridge) 3.3 Heaters & chemical feeders
4 Pool Operations
4.1 Circulation & turnover-rate calculations 4.2 Filtration operation & backwashing 4.3 Routine testing, recordkeeping & troubleshooting
5 Pool Safety
5.1 Suction entrapment & the VGB Act 5.2 Diving, depth markings, signage & RWI prevention 5.3 Electrical safety & emergency response
6 Spa & Hot Tub Operation
6.1 Spa water chemistry & sanitation 6.2 Spa equipment, safety & operation
3.2 Filters (sand, DE, cartridge)
Key Takeaways Explain This Topic AI
Filtration removes suspended particles that chlorine cannot destroy; the three common types are sand, diatomaceous earth (DE), and cartridge.
High-rate sand filters run about 15 gpm/ft², trap roughly 20–40 microns, and are backwashed when pressure rises about 8–10 psi above the clean baseline.
DE filters give the finest filtration (about 1–5 microns) but must be recharged with fresh DE through the skimmer after every backwash.
Cartridge filters do not backwash — you hose the pleated element clean and eventually replace it — which saves water in conservation areas.
Watch the pressure differential: a clean filter reads low pressure and high flow, and a rise of about 8–10 psi over clean signals it is time to clean or backwash.
Last updated: July 2026
Why Filtration Matters
Circulation carries dirt from the pool to the filter, and filtration physically strains out the suspended particles — dust, body oils, pollen, fine debris — that chlorine cannot destroy. Sanitizer kills microorganisms and oxidizes waste; the filter removes the cloudiness. Together they keep water clear and safe. Particle size is measured in microns (millionths of a meter); the human eye can just detect a particle around 35 microns, so a filter that removes finer particles produces visibly clearer water. The three types the CPO exam expects you to know are high-rate sand , diatomaceous earth (DE) , and cartridge .
- The Three Filter Types
- High-Rate Sand
A high-rate sand filter passes water downward through a bed of specially graded #20 silica sand. Particles lodge in the tiny spaces between the sand grains, and the media traps debris down to roughly 20–40 microns — the coarsest of the three. Design flow for a high-rate unit is about 15 gpm per square foot of filter area. As dirt accumulates, resistance rises and the pressure gauge climbs. Backwash when the gauge reads about 8–10 psi above the clean starting pressure : reverse the flow so it lifts and flushes the trapped debris out to waste, then return the valve to filter. Sand is typically replaced every 5–7 years. Pros: simple, durable, inexpensive, low maintenance. Cons: the coarsest filtration, and backwashing wastes water — including the chemically treated pool water sent to drain.
Diatomaceous Earth (DE)
A DE filter coats a set of grids (fingers) with diatomaceous earth , a fine powder of fossilized diatom skeletons. The powder forms a cake that strains the finest particles — down to about 1–5 microns , giving the clearest water of the three. Design flow is low, around 1.5–2 gpm/ft² . When pressure climbs about 8–10 psi over clean, you backwash; but because backwashing strips the DE cake off the grids, you must then recharge (re-coat) the filter by adding a fresh slurry of DE through the skimmer. Periodically the grids are pulled and the old cake hosed off, and spent DE is disposed of per local rules. Pros: finest filtration and sparkling clarity. Cons: the most maintenance, recharge required after every backwash, and DE powder is a respiratory irritant — wear a dust mask when handling it.
Cartridge
A cartridge filter passes water through a large, pleated polyester element whose folds provide a big surface area, trapping particles to roughly 10–20 microns . Because flow per unit of area is modest, cartridge systems use large-surface elements. Crucially, cartridge filters do not backwash. When pressure rises about 8–10 psi over clean, you shut off the pump, remove the cartridge, and hose it clean (soaking it periodically to remove oils); a worn element is simply replaced. Pros: no backwashing, which conserves water and suits drought or water-restricted areas, gentle on plumbing, and no sand or DE to handle. Cons: cleaning is a hands-on chore, cartridges eventually need replacement, and filtration is not as fine as DE.