Study guide
3.3 Heaters & chemical feeders
Certified Pool Operator CPO
Track your progress as you read
Finished sections get a check mark.
1 Introduction, Roles & Regulations
1.1 CPO certification facts, regulations & the operator's role
2 Pool Water Chemistry
2.1 Water balance & the Langelier Saturation Index 2.2 Sanitation & disinfection (chlorine, bromine, breakpoint) 2.3 Chemical testing & alternative sanitizers 2.4 Problem water & chemical-adjustment calculations
3 Pool Equipment
3.1 Pumps & motors 3.2 Filters (sand, DE, cartridge) 3.3 Heaters & chemical feeders
4 Pool Operations
4.1 Circulation & turnover-rate calculations 4.2 Filtration operation & backwashing 4.3 Routine testing, recordkeeping & troubleshooting
5 Pool Safety
5.1 Suction entrapment & the VGB Act 5.2 Diving, depth markings, signage & RWI prevention 5.3 Electrical safety & emergency response
6 Spa & Hot Tub Operation
6.1 Spa water chemistry & sanitation 6.2 Spa equipment, safety & operation
3.3 Heaters & chemical feeders
Key Takeaways Explain This Topic AI
Gas heaters burn gas to heat water in a copper exchanger; they heat fast (good for spas) at roughly 80–84% thermal efficiency and any weather.
Heat pumps move heat from the air with a refrigerant cycle at a high COP (5–6) but heat slowly and lose output as air temperature falls.
Solar collectors heat water for near-zero operating cost but depend on sunshine and need a bypass/diverter valve to route water only when panels are hot.
Erosion (tablet) feeders dissolve trichlor for steady chlorine; never mix trichlor and cal-hypo in one feeder, and peristaltic pumps precisely meter liquid chemicals.
Salt chlorine generators make chlorine on site by electrolysis of dissolved salt, and ORP/pH controllers automate feeders to hold sanitizer and pH setpoints.
Last updated: July 2026
Pool and Spa Heaters
Heaters raise water to a comfortable temperature and hold it there. Three technologies dominate, and the CPO exam expects you to know how each works, its efficiency, and how a bypass protects it.
Gas Heaters
A gas heater burns natural gas or propane in a combustion chamber and passes pool water through a copper heat exchanger above the flame, transferring heat rapidly. Fast heat-up makes gas heaters the natural choice for spas and for intermittent use where water must warm quickly on demand. Standard units run at roughly 80–84% thermal efficiency , and high-efficiency condensing models do better. Gas heaters work in any weather, but fuel cost rises with use. Proper water balance is critical: aggressive (low-pH, low-alkalinity) water corrodes the copper exchanger, while scaling water clogs it — so balanced water directly protects the heater.
Heat Pumps
An electric heat pump does not create heat by combustion; it moves heat from the surrounding air into the water using a refrigerant cycle, essentially an air conditioner run in reverse. This makes it very efficient: a coefficient of performance (COP) of 5–6 means it delivers five to six units of heat for every unit of electricity it consumes. The trade-offs are that heat-up is slow and performance falls as the air cools, because there is less ambient heat to harvest. Heat pumps are ideal for maintaining temperature over a long, warm season rather than for quickly heating a spa.
Solar Heaters
A solar system pumps pool water through dark collector panels — usually mounted on a roof — where the sun warms it before it returns to the pool. Operating cost is close to zero and it is the greenest option, but output depends on available sunshine and adequate panel area. Solar installations use a bypass / diverter valve , often with a controller, to send water through the panels only when the panels are hotter than the pool; otherwise the water would lose heat. Many heaters of every type include an internal bypass so that only part of the flow passes through the exchanger, which protects the heat exchanger from excessive flow and improves overall efficiency.
Sizing and Protecting the Heater
Heater capacity is rated in Btu per hour (British thermal units), and a larger Btu rating heats a given volume of water faster. Operators size a heater to the pool's surface area, desired temperature rise, and how quickly the water must warm — a spa that must reach temperature in an hour needs far more Btu per gallon than a large pool held at a steady temperature all season. Whatever the technology, keeping the water chemically balanced and maintaining adequate flow through the unit are the two habits that most extend a heater's life, because unbalanced water corrodes or scales the exchanger and low flow overheats it.