Study guide

9.3 Generators, Transfer Switches & Standby Power

Connecticut E-2 Unlimited Journeyman Electrician Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Electrical Fundamentals, NEC Navigation & Connecticut Licensing

1.1 Electrical Theory, Units & Basic Formulas 1.2 NEC Layout, Article 90, Definitions & General Requirements 1.3 Connecticut Electrical Licensing, CGS Chapter 393 & DCP Regulations

2 Chapter 2: Services, Feeders & Branch Circuits

2.1 Service Conductors, Service Equipment & Disconnecting Means 2.2 Feeders, Feeder Sizing & Calculations 2.3 Branch Circuit Ratings, Receptacle Outlets & Spacing 2.4 GFCI and AFCI Protection Requirements

3 Chapter 3: Grounding and Bonding (NEC Article 250)

3.1 Grounding Electrode System & Grounding Electrode Conductors 3.2 System Grounding, Main & System Bonding Jumpers 3.3 Equipment Grounding Conductors & Enclosure/Raceway Bonding

4 Chapter 4: Conductors, Ampacity & Cables

4.1 Conductor Materials, Insulation Types & Terminal Ratings 4.2 Ampacity Sizing, Temperature Correction & Bundling Derating 4.3 Cable Assemblies: NM, NMC, MC, AC, TC & UF

5 Chapter 5: Raceways, Boxes & Conduit Fill

5.1 Conduit and Tubing Types & Installation Rules 5.2 Conduit Fill Calculations & Tables 5.3 Outlet, Device & Pull Box Sizing

6 Chapter 6: Overcurrent Protection & Tap Rules

6.1 Overcurrent Protection Devices, Fuses & Circuit Breakers 6.2 Overcurrent Protection Location & Feeder Tap Rules

7 Chapter 7: Electrical Load Calculations (Article 220)

7.1 Residential Dwelling Unit Load Calculations 7.2 Appliance, Cooking & Heating/Cooling Demands 7.3 Commercial & Multifamily Load Calculations

8 Chapter 8: Motors, Motor Circuits & Controllers (Article 430)

8.1 Motor Full-Load Current (FLC) & Conductor Sizing 8.2 Motor Overload Protection & Branch-Circuit Short-Circuit/Ground-Fault Protection 8.3 Motor Controllers, Disconnecting Means & Control Circuits

9 Chapter 9: Transformers, Power Distribution & Standby Systems

9.1 Transformer Principles, Single-Phase/Three-Phase & Sizing 9.2 Transformer Overcurrent Protection & Grounding 9.3 Generators, Transfer Switches & Standby Power

10 Chapter 10: Special Occupancies & Hazardous Locations

10.1 Hazardous (Classified) Locations 10.2 Health Care Facilities (Article 517) 10.3 Swimming Pools, Spas, Fountains & Hot Tubs (Article 680)

11 Chapter 11: Lighting, Signs & HVAC Equipment

11.1 Luminaires, Lampholders & Clothes Closet Clearances 11.2 Electric Signs & Outline Lighting (Article 600) 11.3 Air Conditioning & Refrigerating Equipment (Article 440)

12 Chapter 12: Low Voltage, Fire Alarm & Communications Systems

12.1 Class 1, Class 2, and Class 3 Remote-Control & Signaling Circuits 12.2 Fire Alarm Systems (NEC Article 760) 12.3 Communications Circuits & Optical Fiber Cables

13 Chapter 13: Solar Photovoltaics, Renewable Energy & Energy Storage

13.1 Solar Photovoltaic (PV) Systems Fundamentals & Sizing 13.2 PV Disconnects, Rapid Shutdown & Overcurrent Protection 13.3 Energy Storage Systems (ESS) & Interconnected Power Production

14 Chapter 14: Electrical Safety, High Voltage & Exam Strategy

14.1 Electrical Safety, OSHA Regulations & NFPA 70E 14.2 Medium and High Voltage Systems Over 1,000 Volts 14.3 PSI CT E-2 Exam Strategy, Codebook Navigation & Speed Tactics

9.3 Generators, Transfer Switches & Standby Power

Key Takeaways Explain This Topic AI

NEC 445.13 requires generator terminal conductors to have an ampacity of not less than 115% of the generator nameplate full-load current rating.

NEC Article 700 (Emergency Systems) mandates automatic power restoration within 10 seconds of normal power loss, strict physical wiring separation from all normal circuits, and mandatory selective coordination across all overcurrent devices.

NEC Article 701 (Legally Required Standby Systems) allows up to 60 seconds for automatic power transfer and requires selective coordination, but permits feeder and branch conductors to occupy common raceways with general wiring after transfer.

NEC Article 702 (Optional Standby Systems) serves business or residential convenience, has no mandated restoration time limit, permits manual or automatic transfer, and requires no selective coordination.

A transfer switch with a switched neutral (4-pole) creates a Separately Derived System requiring a neutral-to-ground bond at the generator, whereas a solid neutral (3-pole) switch does not create an SDS, strictly prohibiting bonding at the generator.

Last updated: September 2026

9.3 Generators, Transfer Switches & Standby Power

Quick Reference:

Generator Conductor Ampacity (NEC 445.13): Must be ≥ \ge ≥ 115% of the generator nameplate current rating (unless designed for specific isolated applications).

Generator Disconnecting Means (NEC 445.18): Must disconnect all ungrounded conductors; must be lockable in the open position per 110.25.

NEC Article 700 (Emergency Systems): Human life safety (exit signs, egress lighting, fire pumps). Power restored within 10 seconds (700.12). Strict wiring separation (700.10(B)). Selective coordination mandatory (700.32).

NEC Article 701 (Legally Required Standby): Mandated by building code/AHJ (smoke evacuation, sewage ejectors). Power restored within 60 seconds (701.12). Selective coordination mandatory (701.27).

NEC Article 702 (Optional Standby): Commercial/residential convenience (data preservation, refrigeration). No time limit. Manual or automatic transfer. No selective coordination mandate.

3-Pole Transfer Switch (Solid Neutral): Neutral is continuous back to utility main service. Generator is NOT a Separately Derived System. Neutral is NOT bonded to ground at generator!

4-Pole Transfer Switch (Switched Neutral): Neutral conductor is switched. Generator IS a Separately Derived System. Neutral MUST have an SBJ and GEC connected at the generator per NEC 250.30.

When standard utility electrical service fails due to grid blackouts, severe New England winter storms, or equipment breakdowns, premises must rely on onsite standby power generation. The National Electrical Code strictly stratifies backup power systems into three distinct tiers— Emergency Systems (Article 700) , Legally Required Standby Systems (Article 701) , and Optional Standby Systems (Article 702) —based on the immediacy of the threat to human life. For Connecticut E-2 Journeyperson electricians, understanding generator sizing, transfer switch mechanics, selective coordination, and switched-neutral bonding rules is essential for code compliance and life safety.

1. Generator Installation & Conductor Ampacity (NEC Article 445)

NEC Article 445 governs the installation, electrical protection, and conductor sizing for all stationary and portable generators.

Generator Nameplate Requirements (NEC 445.11)

Every generator must be provided with a manufacturer nameplate displaying:

  • Rated manufacturer kW or kVA;
  • Power factor and frequency (Hz);
  • Rated speed in RPM;
  • Rated voltage and full-load current (amperes);

Temperature rise and insulation class.

Conductor Ampacity Rule (NEC 445.13)

The conductors that run from the generator output terminals to the first overcurrent protective device must have an ampacity of not less than 115 percent of the nameplate current rating of the generator. Conductor Ampacity min = I nameplate × 1.15 \text{Conductor Ampacity}_{\text{min}} = I_{\text{nameplate}} \times 1.15 Conductor Ampacity min ​ = I nameplate ​ × 1.15

Exam Application Problem: A 3-phase, 120/208V diesel generator has a nameplate rating of 100 kW at 0.80 power factor ( 125 kVA 125\text{ kVA} 125 kVA ). The rated full-load current is: I FLC = 125 , 000 VA 208 V × 1.732 = 346.96 Amperes I_{\text{FLC}} = \frac{125,000\text{ VA}}{208\text{ V} \times 1.732} = 346.96\text{ Amperes} I FLC ​ = 208 V × 1.732 125 , 000 VA ​ = 346.96 Amperes Per NEC 445.13, calculate the minimum allowable ampacity for the conductors connecting the generator terminals to its mounted main circuit breaker: Minimum Ampacity = 346.96 A × 1.15 = 399.0 Amperes \text{Minimum Ampacity} = 346.96\text{ A} \times 1.15 = \mathbf{399.0\text{ Amperes}} Minimum Ampacity = 346.96 A × 1.15 = 399.0 Amperes Conductor Selection: Table 310.16 (75°C column) requires a 600 kcmil copper conductor (rated 420A) or two parallel runs of 3/0 AWG copper ( 2 × 200 A = 400 A 2 \times 200\text{A} = 400\text{A} 2 × 200 A = 400 A ).

Generator Disconnecting Means (NEC 445.18)

Generators must be equipped with a readily accessible disconnecting means that disconnects all ungrounded conductors simultaneously. The disconnect must be lockable in the open position in accordance with NEC 110.25 .

Exception for Portable Generators: Cord-and-plug-connected portable generators can use the flanged equipment inlet or plug connection as their disconnecting means.

2. Emergency vs. Legally Required vs. Optional Standby Systems

The National Electrical Code establishes three explicit articles for backup power. Confusing their operational requirements is one of the most common pitfalls on the Connecticut journeyman exam.

Detailed Comparison: Articles 700, 701, and 702

Feature Article 700: Emergency Systems Article 701: Legally Required Standby Article 702: Optional Standby

Core Purpose Human life safety and evacuation (exit signs, emergency stair illumination, fire pumps) Civic/code necessity and firefighter aid (smoke management, sewage pumps, HVAC in public venues) Convenience & business continuity (data centers, commercial refrigeration, residential backup)

Governing Authority Mandated by municipal building codes, NFPA 101 Life Safety Code Mandated by municipal laws, building codes, or local AHJ Chosen voluntarily by facility owner or homeowner

Restoration Time Limit Within 10 seconds of power loss (NEC 700.12) Within 60 seconds of power loss (NEC 701.12) No time limit (manual or automatic transfer)

Wiring Separation Strictly independent: Emergency wiring must never share raceways, boxes, or cables with normal wiring (700.10(B)) Shared wiring permitted: May occupy same raceways/boxes with normal branch circuits after transfer Standard wiring: Completely integrated with normal premises wiring methods

Fire Protection (Feeders) 2-hour fire-rated assembly or concrete encasement in high-occupancy buildings (700.10(D)) Not typically required unless specifically cited by local code None required

Selective Coordination Mandatory across all OCPDs from supply to branch devices (700.32) Mandatory across all OCPDs from supply to branch devices (701.27) Not required by NEC

Transfer Switch Type Automatic only (ATS); listed for emergency use Automatic only (ATS); listed for standby use Manual (MTS) or Automatic (ATS)

The Strict Wiring Isolation Rule (NEC 700.10(B))

Emergency circuit wiring shall be kept entirely independent of all other wiring and equipment. It must not enter the same raceway, cable, box, or cabinet with other general wiring. This ensures that a localized short circuit or mechanical damage in a normal lighting or receptacle branch circuit cannot compromise emergency illumination or fire life-safety pathways.

Exceptions to 700.10(B): Wiring is permitted to share enclosures only inside:

  • The transfer switch enclosure itself;
  • Exit or emergency luminaires supplied from both normal and emergency sources;

A single junction box supplying an emergency luminaire containing two separate branch circuits.

Selective Coordination (NEC 700.32 & 701.27)

Both Emergency Systems (700.32) and Legally Required Standby Systems (701.27) require selective coordination of all overcurrent protective devices. Under NEC Article 100 , selective coordination requires the overcurrent device immediately upstream of any fault to open and clear the fault, while all higher upstream devices remain closed, across the full range of available overcurrents from overloads up to the maximum available short-circuit current.

This prevents a localized branch circuit fault (e.g., an emergency light fixture shorting out in a basement stairwell) from tripping the main emergency distribution breaker, which would plunge the entire high-rise building into total darkness.

3. Transfer Switches (NEC 700.5, 701.5 & 702.5)

A transfer switch is the critical apparatus that switches load circuits between the primary utility power source and the secondary standby generator source. AUTOMATIC TRANSFER SWITCH (ATS)

  • Utility Service (Normal) Standby Generator (Emergency)
  • [ 480V / 208V ] [ 480V / 208V ]
  • | |
  • | |
  • v v
  • +-----------+ +-----------+
  • | Contacts | | Contacts |
  • | NORMAL | | STANDBY |
  • +-----+-----+ +-----+-----+
  • | |
  • +--------------------+ +---------------------+
  • | |
  • [ MECHANICAL INTERLOCK ]
  • (Prevents Simultaneous Closure!)
  • | |
  • v v
  • +----------------+
  • | Critical Load |
  • | Panelboard |
  • +----------------+
  • Transfer Switch Classifications

Automatic Transfer Switch (ATS): Microprocessor-controlled device that continuously monitors utility voltage and frequency. Upon detecting a blackout or sustained undervoltage (e.g., below 85% nominal), the ATS signals the generator engine to start, waits for generator voltage and frequency to stabilize, and automatically transfers the load. When utility power stabilizes for a preset duration (typically 15 to 30 minutes), the ATS retransfers load to utility and initiates engine cooldown.

Manual Transfer Switch (MTS): Manually operated double-throw switch or breaker assembly, common in residential and small commercial Optional Standby Systems.

Mandatory Interlocking (Preventing Utility Backfeeding)

Under NEC 700.5, 701.5, and 702.5, all transfer equipment must be designed and installed to prevent the inadvertent interconnection of normal and standby sources . Mechanical and electrical interlocks physically prevent the utility contacts and generator contacts from being closed at the same time.

The Danger of Backfeeding: If a standby generator backfeeds into utility transformers, low-voltage power (e.g., 120/240V) steps up through the utility pole-mounted transformer to primary transmission levels ( 7,200 to 13,800 volts ), instantly electrocuting utility line workers repairing storm damage miles away.

4. 3-Pole vs. 4-Pole Transfer Switches & Grounding Architecture

One of the most heavily tested, high-yield technical subjects on the Connecticut E-2 examination is whether a standby generator is classified as a Separately Derived System (SDS) under NEC 250.30 .

What Dictates Separately Derived System Status?

The determining factor is whether the neutral conductor is switched inside the transfer switch: 3-POLE TRANSFER SWITCH (SOLID NEUTRAL) 4-POLE TRANSFER SWITCH (SWITCHED NEUTRAL)

====================================== =========================================

- Switches Phase A, B, C only. - Switches Phase A, B, C AND Neutral.

- Neutral is unbroken (Solid / Continuous). - Neutral is completely broken/switched.

- Generator is NOT an SDS! - Generator IS an SDS per Article 100/250.30!

- Neutral is grounded at Utility Service. - Neutral MUST be bonded at Generator!

- NO System Bonding Jumper at Generator! - System Bonding Jumper (SBJ) REQUIRED at Generator!

- NO Grounding Electrode Conductor for - Grounding Electrode Conductor (GEC)

Neutral at Generator! REQUIRED at Generator to Grounding Electrode!

3-Pole Transfer Switch (Solid Neutral Installation)

In a 3-phase, 4-wire installation with a 3-pole ATS, the three ungrounded phase conductors ( A − B − C A-B-C A − B − C ) are switched, but the neutral conductor connects to a continuous, solid neutral bar inside the ATS. The neutral conductor remains solidly tied to the main utility service neutral at all times.

Generator Classification: Because the generator neutral has a direct, permanent electrical connection to the utility supply neutral, the generator is NOT a Separately Derived System .

Grounding Mandate:

Do NOT install a System Bonding Jumper (SBJ) at the generator! The neutral must float inside the generator housing.

An Equipment Grounding Conductor (EGC) is run from the transfer switch to bond the metallic generator frame.

If an SBJ were installed inside the generator, the neutral current would split between the neutral and the equipment ground back to the service, creating dangerous circulating ground-fault currents and tripping ground-fault protection (GFP) relays.

4-Pole Transfer Switch (Switched Neutral Installation)

In a 3-phase, 4-wire installation with a 4-pole ATS, all three phase conductors ( A − B − C A-B-C A − B − C ) and the neutral conductor are simultaneously switched. When transferred to generator power, the load neutral is completely disconnected from the utility neutral.

Generator Classification: Because there is no direct electrical connection between the generator neutral and the utility neutral, the generator IS a Separately Derived System .

Grounding Mandate:

A System Bonding Jumper (SBJ) must be installed at the generator (or inside the ATS if neutral is switched there) per NEC 250.30(A)(1).

A Grounding Electrode Conductor (GEC) must be installed from the generator neutral/grounding bus to an approved grounding electrode (such as ground rods or building steel) per NEC 250.30(A)(5) and Table 250.66.

Loading diagram... Transfer Switch Neutral Configuration & SDS Grounding Determination