Study guide
1.3 Legal Descriptions and Surveys
Connecticut Real Estate Salesperson Exam
Track your progress as you read
Finished sections get a check mark.
1 Standalone Coverage Map
How This Guide Maps to the Connecticut Salesperson Exam
2 Introduction: Connecticut Real Estate Exam Overview
Connecticut Real Estate Salesperson Exam Overview
3 National Portion: Chapter 1: Real Property Characteristics, Legal Descriptions & Property Use
1.1 Real Property vs. Personal Property 1.2 Physical and Economic Characteristics of Real Property 1.3 Legal Descriptions and Surveys 1.4 Land-Use Controls, Public & Private Restrictions, and Encumbrances
4 National Portion: Chapter 2: Forms of Ownership, Transfer & Recording of Title
2.1 Estates, Ownership Forms, Rights, and Interests 2.2 Deeds, Title Transfer, Title Insurance, and Recording
5 National Portion: Chapter 3: Property Value & Appraisal
3.1 The Concept of Value and Economic Principles 3.2 The Appraisal Process and USPAP Basics 3.3 Valuation Approaches (Sales Comparison, Cost, Income) and BPOs
6 National Portion: Chapter 4: Real Estate Contracts & Agency
4.1 Contract Types and Required Elements 4.2 Contract Performance, Breach, and Enforceability 4.3 Listing and Sales Contracts and Contingencies 4.4 Agency Relationships, Fiduciary Duties, and Disclosure
7 National Portion: Chapter 5: Real Estate Practice (Brokerage, Fair Housing, Risk)
5.1 Broker Responsibilities, Brokerage Agreements, and Compensation 5.2 Federal Fair Housing Law and Protected Classes 5.3 Advertising, Antitrust, and Risk Management
8 National Portion: Chapter 6: Property Disclosures & Environmental Issues
6.1 Property Conditions and Environmental Hazards 6.2 Disclosure Obligations, Stigmatized Property, and Liability
9 National Portion: Chapter 7: Financing & Settlement
7.1 Financing Concepts, Notes, Mortgages, and Deeds of Trust 7.2 Loan Types, Lender Requirements, PMI, and Mortgage Insurance 7.3 Federal Financing Regulations (RESPA, TILA, ECOA, TRID) 7.4 Settlement, Closing Statements, and Prorations
10 National Portion: Chapter 8: Real Estate Math Calculations
8.1 Area, Volume, and Valuation Calculations 8.2 Commission, Financing, and Interest Calculations 8.3 Proration, Transfer Tax, and Investment Math
11 Chapter 1: CT Real Estate Commission & Licensing
1.1 Connecticut Real Estate Commission 1.2 Connecticut License Requirements 1.3 License Maintenance and Renewal
12 Chapter 2: Agency & Disclosure
2.1 Connecticut Agency Relationships 2.2 Connecticut Property Disclosures 2.3 Connecticut Fair Housing
13 Chapter 3: Contracts & Property
3.1 Connecticut Contract Requirements 3.2 Connecticut Property Law 3.3 Connecticut Landlord-Tenant & Common Interest Ownership
14 Chapter 4: Trust Accounts & Violations
4.1 Connecticut Trust Account Requirements 4.2 License Law Violations & Discipline
1.3 Legal Descriptions and Surveys
Key Takeaways Explain This Topic AI
Three legal-description methods: metes and bounds, rectangular (government) survey, and lot and block (recorded plat).
Metes and bounds must start and return to the point of beginning; monuments control over conflicting distances.
Memorize: acre = 43,560 sq ft; section = 1 sq mile = 640 acres; township = 36 sq miles = 36 sections.
To size a sectional description, multiply all denominators and divide 640 by the product.
Datum and benchmarks fix vertical elevation for air lots and condominium units; street addresses are never legally sufficient.
Last updated: June 2026
Why Street Addresses Are Not Enough
A legal description identifies a parcel with enough precision that a surveyor could locate its exact boundaries. Street addresses change and are not legally sufficient. The national exam tests three accepted methods : metes and bounds, the rectangular (government) survey system, and the lot-and-block (recorded plat) system.
1. Metes and Bounds
The oldest method, used in the original 13 colonies and irregular parcels. It begins at a defined point of beginning (POB) , traces metes (distances and compass bearings) and bounds (boundaries such as roads, monuments, or natural features), and must return to the POB to close the parcel. A description that does not close is defective. Monuments (a stone, an iron pin) control over recited distances if the two conflict.
2. Rectangular (Government) Survey System
Established by the Land Ordinance of 1785, this system uses principal meridians (run north-south) and base lines (run east-west). From their intersection, land is divided into a grid:
- Unit Size
- Township 6 miles x 6 miles = 36 square miles
- Section 1 mile x 1 mile = 640 acres
- Quarter section 160 acres
- Quarter-quarter section 40 acres
Each township contains 36 sections , numbered 1 to 36 in a serpentine (boustrophedonic) pattern starting at the northeast corner. One acre = 43,560 square feet .
Reading a Sectional Description
Read a description like "the NW 1/4 of the SE 1/4 of Section 10" right to left , multiplying fractions by 640 acres.
- SE 1/4 of Section 10 = 1/4 x 640 = 160 acres
- NW 1/4 of that = 1/4 x 160 = 40 acres
Worked numeric: "The S 1/2 of the NE 1/4 of the SW 1/4" = 1/2 x 1/4 x 1/4 x 640 = 640 / 32 = 20 acres . Always multiply all the denominators (2 x 4 x 4 = 32) and divide 640 by the product. If a value is missing on test day, work the chain one step at a time, carrying the acreage forward.
3. Lot and Block (Recorded Plat / Subdivision) System
Used for subdivided urban land. A developer records a subdivision plat map in the county; each parcel is then described by its lot number, block number, the subdivision name, and the recording reference (book and page). This is the simplest, most common method for residential lots. Example: "Lot 7, Block 3, Sunny Acres Subdivision, as recorded in Plat Book 12, Page 45." Because the plat map already shows precise dimensions, easements, and setbacks, the deed need only cite the lot, block, and recording data; the recorded map supplies the rest.
This is why most residential closings you will handle use lot-and-block rather than lengthy metes-and-bounds calls.
Combining Systems and Surveys
The three methods are not mutually exclusive. A subdivision plat is itself laid out within a government-survey section, and an irregular tract inside a section is often described by metes and bounds anchored to a section corner. A licensed surveyor prepares the description and a plat (drawing) of the boundaries; a spot survey also locates improvements to reveal encroachments. The description in the deed must match the recorded plat or the survey, or a title cloud results.
Datum, Benchmarks, and Air Lots
Vertical (elevation) measurements use a datum — a defined point, surface, or plane from which elevations are measured (the official datum is mean sea level). A benchmark is a permanent marker, often a brass disk set by the National Geodetic Survey, showing elevation relative to the datum. Air lots and condominium units are described in three dimensions using elevation references because ownership is stacked vertically, with the air space above and the structure described relative to the datum.