Study guide
11.6 Duplex Stainless Metallurgy & Dissimilar-Metal Ferrite Prediction
AWS CWEng Certified Welding Engineer Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & CWEng Exam Overview
About the CWEng Exam: Four Parts, 163 Questions & Testing Logistics Scoring, Composite Weighting, Eligibility & Five-Year Renewal How to Use This Guide & Build Your Open-Book Reference Set
2 Chapter 1: Mathematics & Statistics for Welding Engineers
1.1 Engineering Mathematics: Algebra, Trigonometry & Geometry in Weldments 1.2 Differential & Integral Calculus Fundamentals in Engineering Analysis 1.3 Applied Engineering Statistics, Population Distributions & Quality Metrics 1.4 Polynomial Equations, Conic Sections & Complex Numbers
3 Chapter 2: Physics Fundamentals & Mechanics
2.1 Unit Systems, Dimensional Analysis & Engineering Conversions 2.2 Mechanics: Statics, Equilibrium, Force Vectors & Moments 2.3 Work, Energy, Power & Mechanical Advantage in Welding Systems 2.4 Thermal Physics, Linear/Volumetric Expansion & Heat Capacity
4 Chapter 3: General & Physical Chemistry for Welding
3.1 Atomic Structure, Bonding & Solid-Solution Thermodynamics 3.2 Hume-Rothery Compatibility, Interstitial Strain & HSLA Microalloy Scavenging 3.3 Gas Laws, Dalton Partial Pressures, Arc Dissociation & Sieverts Law 3.4 Cylinder Capacity, Available Arc Time & Gas-Related Porosity Diagnosis 3.5 Redox Thermodynamics, Deoxidation & Slag-Metal Refining 3.6 Basicity Index Calculations, Toughness Prediction & Cryogenic Consumable Selection
5 Chapter 4: Strength of Materials & Mechanics of Materials
4.1 Engineering vs. True Stress-Strain, Elastic Constants & Z-Direction Ductility 4.2 Plane Stress vs. Plane Strain, Triaxial Restraint & Alloy Property Comparison 4.3 Beam Bending, Transverse Shear, Torsion & Mohr Circle Construction 4.4 Multiaxial Yield Criteria & Combined-Load Analysis of Welded Members 4.5 Fatigue Life, Weld-Toe Stress Concentration & Paris-Erdogan Crack Growth 4.6 LEFM Fracture Toughness, Ductile-Brittle Transition & Larson-Miller Creep 4.7 Comparative Failure-Mode Synthesis & Integrated Flaw and Creep Assessment
6 Chapter 5: Heat Transfer & Fluid Mechanics in Welding
5.1 Fourier Conduction, Rosenthal Moving Heat Source & 2D vs. 3D Heat Flow 5.2 Adams Cooling Rate, the t8/5 Window & HAZ Peak-Temperature Distribution 5.3 Convection, Stefan-Boltzmann Radiation & Emissivity of Weld Surfaces 5.4 Arc Radiation Losses, Preheat Maintenance & PWHT Boundary Conditions 5.5 Fluid Statics, Bernoulli, Viscosity & Reynolds-Number Regimes 5.6 Gas Lens Mechanics, Buoyancy Effects & Torch Flow Design 5.7 Hyperbaric, Vacuum & Controlled-Atmosphere Welding Environments
7 Chapter 6: Electrical Engineering Principles for Welding Systems
6.1 DC and AC Waveforms, Polarity Thermodynamics & Welding Circuit Analysis 6.2 Joule Heating, Electrode Stickout Preheating & Circuit Voltage Distribution 6.3 Power Factor, Reactance, Impedance & Magnetic Transformer Principles 6.4 Lorentz Force, Electromagnetic Pinch Effect & Arc Blow
8 Chapter 7: Welding Heat Sources & Arc Physics
7.1 Volt-Ampere Characteristics, Operating Point, Self-Regulation & OCV Limits 7.2 Inductance, Slope Control & Dynamic Power-Source Response 7.3 Arc Fall Regions, Cathode Emission Mechanisms & Shielding-Gas Ionization 7.4 Maecker Plasma Jet, Degree of Ionization & Anode Heat Partitioning 7.5 Droplet Force Balance & Classification of Metal Transfer Regimes 7.6 Transition Current, Mode Comparison & Pulsed Waveform Design
9 Chapter 8: Arc Welding Processes & Parameter Controls
8.1 Shielded Metal Arc Welding (SMAW): Electrode Flux Chemistries & Variables 8.2 GMAW Process Physics, Transfer Modes & Shielding Gas Interactions 8.3 Solid, Metal-Cored & Flux-Cored Wires with CTWD and Parameter Envelopes 8.4 Gas Tungsten (GTAW) & Plasma Arc Welding (PAW): Electrodes & Keyholing 8.5 Submerged Arc Welding (SAW): Flux Basicity, Multi-Wire & High-Deposition Systems
10 Chapter 9: Advanced, Resistance & Solid-State Joining Processes
9.1 High-Energy-Density Beam Physics & Electron Beam Welding 9.2 Laser Beam Welding, EBW/LBW Comparison & Fiber Laser Parameter Derivation 9.3 Resistance Welding Physics, Electrode Materials & Spot Weld Sequence 9.4 Nugget Sizing, Seam and Projection Welding, and Lobe Curve Process Windows 9.5 Solid-State Joining: Friction Stir Welding (FSW), Explosion & Diffusion 9.6 Thermal Cutting & Gouging: Oxyfuel, Plasma Arc and Air Carbon Arc 9.7 High-Frequency, Flash, Stud & Ultrasonic Welding; Surfacing and Thermal Spray
11 Chapter 10: Physical & Transformation Metallurgy of Steels
10.1 Fe-Fe3C System, Crystal Lattices, c/a Ratio & Interstitial Solubility 10.2 Critical Temperatures, Invariant Reactions & the Lever Rule 10.3 Alloying Elements, the Gamma Loop & Phase-Fraction Calculations 10.4 TTT and CCT Diagrams, Constitutional Supercooling & Scheil Microsegregation 10.5 Non-Equilibrium Transformation Products & Martensite Modeling 10.6 HAZ Anatomy, Microstructural Sub-Zones & Multi-Pass Reheated Regions 10.7 HAZ Hardness Traverses, Toughness Gradients & Peak-Temperature Control
12 Chapter 11: Weldability, Cracking Mechanisms & Alloy Metallurgy
11.1 Hydrogen Cracking Conditions, Carbon Equivalent & Diffusible Hydrogen Control 11.2 Preheat, Interpass and Post-Heat Calculations for Cold-Crack Prevention 11.3 Solidification Cracking, Bead Aspect Ratio, Liquation & Lamellar Tearing 11.4 Lamellar Tearing Mitigation & Hot-Cracking Susceptibility Evaluation 11.5 Stainless Families, Schaeffler and WRC-1992 Diagrams, Ferrite Number & Sensitization 11.6 Duplex Stainless Metallurgy & Dissimilar-Metal Ferrite Prediction 11.7 Aluminum Oxide and Porosity Control, and Titanium Reactive-Metal Welding 11.8 Nickel Superalloys, Strain-Age Cracking & Guinier-Preston Aging Sequences
13 Chapter 12: Weldment Design, Stress Analysis & Joint Mechanics
12.1 AWS A2.4 Welding Symbol Anatomy, Symbol Library & Dimension Syntax 12.2 Joint Architecture, CJP versus PJP, and NDE Examination Symbols 12.3 Fillet and Groove Weld Sizing under Direct Stress in ASD and LRFD 12.4 Plug and Slot Welds, Stress Gradients & the Fillet Weld Break Test 12.5 Eccentric Loading Analysis: Elastic Vector Method vs Instantaneous Center 12.6 Fatigue Design of Welded Connections & Residual Stress/Distortion Control
14 Chapter 13: Non-Destructive Examination (NDE) & Discontinuity Analysis
13.1 Visual Testing Gages & Liquid Penetrant Capillary Mechanics 13.2 Magnetic Particle Testing: Flux Leakage, Field Geometry & Prod Amperage 13.3 Radiographic Physics, Geometric Unsharpness, Density & IQI Sensitivity 13.4 Computed and Digital Radiography & Radiographic Discontinuity Interpretation 13.5 Acoustic Wave Mechanics, Refraction & Angle-Beam Sound-Path Geometry 13.6 AWS D1.1 Decibel Rating, Phased Array & Time-of-Flight Diffraction
15 Chapter 14: Brazing, Soldering & Industrial Welding Safety
14.1 Brazing Thermodynamics, Capillary Wetting Physics & Joint Clearance 14.2 AWS A5.8 Brazing Filler Metals, FB Fluxes & Industrial Heating Processes 14.3 Soldering Fundamentals, Flux Chemistries & Intermetallic Formation 14.4 Hierarchy of Controls, Electric Shock Physics & Industrial Ventilation 14.5 Fume Exposure Limits, Arc Radiation, Hot Work and Confined-Space Entry 14.6 Arc-Generated Toxic Gases, Moving-Equipment Hazards & TWA Exposure Calculation
16 Chapter 15: Structural Fabrication & AWS D1.1 Code Implementation
15.1 AWS D1.1 Scope, Prequalification Limits, Base-Metal Groups & Matching Filler 15.2 Prequalified Joint Details, Backing Systems & Joint Specification Verification 15.3 Thermal Cut Edges, Fit-Up Tolerances & Minimum Preheat Requirements 15.4 Preheat Application Zones, Measurement Instrumentation & Fabrication Audits 15.5 PWHT Fundamentals, D1.1 Thermal Cycles & Visual Acceptance Criteria 15.6 D1.1 Nondestructive Examination Protocols, PWHT Scheduling & Visual Audit Practice
17 Chapter 16: Welding Procedure Qualification (WPS & PQR) per ASME IX & AWS B2.1
16.1 PQR versus WPS Hierarchy, Qualification Workflow & Standard Procedures 16.2 Manufacturer Responsibility, Subcontracting Limits & Multi-Process Qualification 16.3 Essential, Supplementary Essential and Nonessential Variables with Heat Input Mechanics 16.4 Waveform-Controlled Power Sources, Appendix H & Heat-Input Compliance 16.5 P-Numbers, Group Numbers, F-Numbers & A-Numbers 16.6 QW-451 Mechanical Test Protocols & Procedure Qualification Test Evaluation
18 Chapter 17: Filler Metal Specifications, Selection & Consumable Control
17.1 AWS A5 Architecture: SMAW, GMAW/GTAW and FCAW Consumable Classifications 17.2 SAW Wire-Flux Systems, Alloy Pickup & PWHT Property Effects 17.3 Stainless Filler Specifications, Solidification Modes & Dissimilar-Metal Joints 17.4 AWS A5.10 Aluminum Filler Selection & Dilution and Ferrite-Number Calculations 17.5 Consumable Storage, Conditioning Envelopes & Atmospheric Exposure Limits 17.6 Low-Hydrogen Designators, the Yurioka Parameter & Preheat Sizing
19 Chapter 18: Welder Performance Qualification, Quality Management & Welding Economics
18.1 Welder Qualification Philosophy, Test Positions & Thickness and Diameter Ranges 18.2 F-Number Hierarchy, Operator Qualification & Continuity Requirements 18.3 ISO 3834, Welding Coordination, Inspection Test Plans & Equipment Validation 18.4 EN 10204 Material Certification, Traceability & Heat-Input Nonconformance Auditing 18.5 Weld Cost Anatomy, Deposition Rates, Operating Factor & the Overwelding Law 18.6 Economic Optimization Strategies & Fabrication Cost Comparison
11.6 Duplex Stainless Metallurgy & Dissimilar-Metal Ferrite Prediction
Key Takeaways Explain This Topic AI
Austenitic stainless steel weld deposits must typically contain 3 to 8 Ferrite Number (FN) (or 4 to 10 FN) to ensure primary ferrite (FA) solidification, which prevents hot solidification cracking while avoiding embrittling sigma phase or cryogenic toughness degradation.
Duplex stainless steel welding requires tight heat input control (0.5 to 2.5 kJ/mm), nickel-overalloyed fillers (e.g., 2209), and nitrogen-bearing shielding gas (Ar + 1-2% N2) to maintain a balanced 40-60% austenite-ferrite phase proportion and prevent brittle intermetallic precipitation.
Duplex stainless steels have both a minimum and a maximum heat input: too fast a cooling rate leaves excess ferrite, and too slow a rate precipitates embrittling intermetallic phases.
Duplex filler metals are deliberately over-alloyed with nickel so that the as-welded deposit re-forms enough austenite on cooling.
Dissimilar-metal joints must be assessed at the diluted composition, so the chromium and nickel equivalents are computed after estimating dilution from each base metal.
Last updated: September 2026
Duplex Stainless Steel Welding Metallurgy
Duplex stainless steels (e.g., 2205: 22% Cr, 5% Ni, 3% Mo, 0.17% N) feature a balanced, two-phase microstructure of approximately 40% to 60% austenite (gamma) and 40% to 60% delta ferrite (delta) . They provide roughly double the yield strength of austenitic grades, coupled with superior resistance to chloride stress corrosion cracking (CSCC) and localized pitting (Pitting Resistance Equivalent Number, PRE_N = Cr + 3.3*Mo + 16*N >= 35 ).
Solidification & Phase Balance Kinetics
Unlike austenitic stainless steels, duplex alloys solidify 100% as delta ferrite (L -> delta). Austenite only forms as a solid-state transformation product upon cooling between 1300°C and 1000°C:
Rapid Cooling (Low Heat Input, < 0.5 kJ/mm): Insufficient time for nitrogen and nickel to diffuse and nucleate austenite. The HAZ freezes with excessive ferrite (> 75% to 85% delta). Excess nitrogen cannot remain dissolved in ferrite, precipitating as brittle chromium nitrides (Cr2N) within ferrite grains, destroying impact toughness and pitting corrosion resistance.
Slow Cooling (Excessive Heat Input, > 2.5 kJ/mm): Prolonged residence time in the 600°C to 950°C range promotes precipitation of brittle intermetallic phases:
Sigma phase (sigma, Fe-Cr-Mo intermetallic): Highly embrittling; as little as 1% to 2% sigma phase drastically degrades room-temperature toughness and corrosion resistance.
Chi phase (chi) and secondary austenite (gamma_2).
Welding Engineering Protocols for Duplex Steels
Heat Input Constraints: Maintain heat input strictly within 0.5 to 2.5 kJ/mm for standard 2205 duplex, and 0.2 to 1.5 kJ/mm for 2507 super-duplex.
Maximum Interpass Temperature: Constrain interpass temperatures to <= 150°C (300°F) for 2205, and <= 100°C (212°F) for 2507.
Over-Alloyed Filler Metals: Autogenous welding (no filler) produces an unacceptably ferritic weld metal (> 80% delta). Weld procedures mandate nickel-overalloyed filler metals (e.g., AWS ER2209 with 8.5% to 10.0% Ni to join 5% Ni base plate) to drive austenite reformation in the fusion zone.
Nitrogen-Bearing Shielding Gas: In GTAW and GMAW, high arc temperatures drive nitrogen out of the molten pool. Adding 1% to 2% N2 to argon shielding gas (and 99.999% N2 for root purging) maintains nitrogen levels, promoting prompt austenite reformation and preserving corrosion resistance.
- Worked Numerical Example: Dissimilar Metal Weld & WRC-1992 Ferrite Calculation
- Problem Statement
A welding engineer must qualify a procedure for joining a carbon steel pressure vessel nozzle (ASTM A106 Grade B) to an austenitic stainless steel pipe (ASTM A312 TP304L) using Gas Tungsten Arc Welding (GTAW) with AWS ER309L filler metal. The joint design is a single-V butt weld. Metallurgical cross-sectioning verifies an overall weld dilution of 30% (15% from A106B and 15% from 304L), with 70% contributed by the ER309L filler metal.
The certified compositions are as follows (weight percent):
- Base Metal 1 (A106B): 0.22% C, 0.80% Mn, 0.25% Si, 0.05% Cr, 0.02% Mo, 0.08% Ni, 0.15% Cu, 0.008% N, 0.00% Nb
- Base Metal 2 (304L): 0.025% C, 1.40% Mn, 0.45% Si, 18.30% Cr, 0.20% Mo, 8.20% Ni, 0.30% Cu, 0.060% N, 0.00% Nb
Filler Metal (ER309L): 0.020% C, 1.70% Mn, 0.40% Si, 23.50% Cr, 0.10% Mo, 13.20% Ni, 0.10% Cu, 0.045% N, 0.00% Nb
Engineering Tasks:
Calculate the Chromium Equivalent (Cr_eq) and Nickel Equivalent (Ni_eq) for all three materials using the WRC-1992 formulas: Cr_eq = Cr + Mo + 0.7*Nb
Ni_eq = Ni + 35*C + 20*N + 0.25*Cu
Calculate the resulting mixed weld deposit Cr_eq and Ni_eq based on the specified dilution fractions (15% BM1 + 15% BM2 + 70% FM).
Using the linearized WRC-1992 iso-ferrite relationship for the 2 to 15 FN regime: FN approx -14.4 + 3.96 * (Cr_eq - 0.93*Ni_eq) estimate the Ferrite Number (FN) of the deposit.
Metallurgically evaluate whether the deposit successfully prevents solidification cracking, avoids excessive delta ferrite, and avoids martensite formation.
- Step-by-Step Solution
- Step 1: Calculate WRC-1992 Equivalents for Components
- Base Metal 1 (A106B): Cr_eq, BM1 = 0.05 + 0.02 + 0.7*(0) = 0.07%
- Ni_eq, BM1 = 0.08 + 35*(0.22) + 20*(0.008) + 0.25*(0.15)
- Ni_eq, BM1 = 0.08 + 7.70 + 0.16 + 0.0375 = 7.9775% approx 7.98%
- Base Metal 2 (304L): Cr_eq, BM2 = 18.30 + 0.20 + 0.7*(0) = 18.50%
- Ni_eq, BM2 = 8.20 + 35*(0.025) + 20*(0.060) + 0.25*(0.30)
- Ni_eq, BM2 = 8.20 + 0.875 + 1.20 + 0.075 = 10.35%
- Filler Metal (ER309L): Cr_eq, FM = 23.50 + 0.10 + 0.7*(0) = 23.60%
- Ni_eq, FM = 13.20 + 35*(0.020) + 20*(0.045) + 0.25*(0.10)
- Ni_eq, FM = 13.20 + 0.70 + 0.90 + 0.025 = 14.825% approx 14.83%
Step 2: Calculate Mixed Weld Metal Equivalents Applying the dilution mass balance: Cr_eq, deposit = 0.15*(Cr_eq, BM1) + 0.15*(Cr_eq, BM2) + 0.70*(Cr_eq, FM)
- Cr_eq, deposit = 0.15*(0.07) + 0.15*(18.50) + 0.70*(23.60)
- Cr_eq, deposit = 0.0105 + 2.775 + 16.52 = 19.3055% approx 19.31%
- Ni_eq, deposit = 0.15*(Ni_eq, BM1) + 0.15*(Ni_eq, BM2) + 0.70*(Ni_eq, FM)
- Ni_eq, deposit = 0.15*(7.978) + 0.15*(10.35) + 0.70*(14.825)
- Ni_eq, deposit = 1.1967 + 1.5525 + 10.3775 = 13.1267% approx 13.13%
Step 3: Estimate Ferrite Number (FN) Effective Parameter = Cr_eq - 0.93*Ni_eq = 19.31 - 0.93*(13.13) = 19.31 - 12.21 = 7.10
FN approx -14.4 + 3.96*(7.10) = -14.4 + 28.12 = 13.72 approx 13.7 FN
Note: Graphical reading on the official WRC-1992 coordinate grid at (19.31, 13.13) yields 9.0 to 12.0 FN .
Step 4: Metallurgical Evaluation
Solidification Cracking: With Cr_eq / Ni_eq = 19.31 / 13.13 = 1.47, the weld pool solidifies in the primary ferritic FA mode . The presence of approx 9 to 12 FN provides complete immunity against hot cracking.
Martensite Avoidance: The deposit coordinates (19.31, 13.13) fall completely outside the martensite boundary on the Schaeffler/WRC diagrams, ensuring a tough, ductile austenitic-ferritic matrix.
Conclusion: ER309L provides the necessary buffering margin against carbon steel dilution, preventing both brittle martensite and hot cracking.
- Real-World Engineering Scenarios & Exam Pitfalls
- Industrial Scenario: Intergranular Stress Corrosion Failure in Brewery Piping
A craft brewing facility installed an uninsulated AISI 304 schedule 10 process piping system carrying warm wash water (65°C) with trace chlorides. Piping spools were field-welded using manual GTAW with standard AWS ER308 filler wire. After 14 months of operation, multiple circumferential hairline leaks opened in the Heat-Affected Zone approximately 2 mm away from the weld toe. Metallographic sectioning revealed severe grain-boundary ditching conforming to ASTM A262 Practice A, with deep intergranular stress corrosion cracks propagating through chromium-depleted boundaries.
Root Cause Analysis:
The pipe base material was dual-certified standard 304 with carbon measured at 0.065%.
Welds were made using high heat input (> 2.2 kJ/mm) with no interpass temperature restrictions, leaving the HAZ in the 500°C to 850°C sensitization window for minutes.
The fabricator failed to specify low-carbon "L" grades.
Corrective Action: The entire piping network was replaced with AISI 304L (C = 0.022%) welded with ER308L , heat input was constrained to <= 1.0 kJ/mm, and maximum interpass temperature was capped at 100°C, completely eliminating sensitization.
Common Exam Traps
Exam Trap 1: Assuming 100% Austenite Is Best for Corrosion Resistance While fully austenitic welds (0 FN) are required for specialized urea or concentrated nitric acid equipment, selecting 0 FN for general structural fabrication is disastrous. A fully austenitic weld pool solidifies in Mode A, possessing practically zero tolerance for sulfur and phosphorus and resulting in severe centerline hot cracking. You must maintain 3 to 8 FN for structural austenitic welds.
Exam Trap 2: Neglecting Nitrogen in the Schaeffler Diagram Exam questions often ask why the Schaeffler diagram should not be used for modern stainless steel calculations. Schaeffler completely omits nitrogen. Nitrogen is an exceptionally potent austenite stabilizer (20 to 30 times more powerful than nickel). Neglecting nitrogen causes Schaeffler to grossly overestimate delta ferrite, leading to inaccurate filler metal selections. Always cite the WRC-1992 diagram.
Exam Trap 3: Cooling Rate Strategy for Duplex Stainless Steels Do not apply the carbon steel rule ("slower cooling is always safer") or the austenitic rule ("quench as fast as possible") to duplex stainless steel. Extremely rapid cooling leaves duplex HAZs with > 80% brittle ferrite and chromium nitride precipitates. Extremely slow cooling causes catastrophic embrittling sigma phase. Duplex welding requires a strictly controlled moderate cooling window governed by heat inputs of 0.5 to 2.5 kJ/mm .