Study guide
14.6 Arc-Generated Toxic Gases, Moving-Equipment Hazards & TWA Exposure Calculation
AWS CWEng Certified Welding Engineer Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & CWEng Exam Overview
About the CWEng Exam: Four Parts, 163 Questions & Testing Logistics Scoring, Composite Weighting, Eligibility & Five-Year Renewal How to Use This Guide & Build Your Open-Book Reference Set
2 Chapter 1: Mathematics & Statistics for Welding Engineers
1.1 Engineering Mathematics: Algebra, Trigonometry & Geometry in Weldments 1.2 Differential & Integral Calculus Fundamentals in Engineering Analysis 1.3 Applied Engineering Statistics, Population Distributions & Quality Metrics 1.4 Polynomial Equations, Conic Sections & Complex Numbers
3 Chapter 2: Physics Fundamentals & Mechanics
2.1 Unit Systems, Dimensional Analysis & Engineering Conversions 2.2 Mechanics: Statics, Equilibrium, Force Vectors & Moments 2.3 Work, Energy, Power & Mechanical Advantage in Welding Systems 2.4 Thermal Physics, Linear/Volumetric Expansion & Heat Capacity
4 Chapter 3: General & Physical Chemistry for Welding
3.1 Atomic Structure, Bonding & Solid-Solution Thermodynamics 3.2 Hume-Rothery Compatibility, Interstitial Strain & HSLA Microalloy Scavenging 3.3 Gas Laws, Dalton Partial Pressures, Arc Dissociation & Sieverts Law 3.4 Cylinder Capacity, Available Arc Time & Gas-Related Porosity Diagnosis 3.5 Redox Thermodynamics, Deoxidation & Slag-Metal Refining 3.6 Basicity Index Calculations, Toughness Prediction & Cryogenic Consumable Selection
5 Chapter 4: Strength of Materials & Mechanics of Materials
4.1 Engineering vs. True Stress-Strain, Elastic Constants & Z-Direction Ductility 4.2 Plane Stress vs. Plane Strain, Triaxial Restraint & Alloy Property Comparison 4.3 Beam Bending, Transverse Shear, Torsion & Mohr Circle Construction 4.4 Multiaxial Yield Criteria & Combined-Load Analysis of Welded Members 4.5 Fatigue Life, Weld-Toe Stress Concentration & Paris-Erdogan Crack Growth 4.6 LEFM Fracture Toughness, Ductile-Brittle Transition & Larson-Miller Creep 4.7 Comparative Failure-Mode Synthesis & Integrated Flaw and Creep Assessment
6 Chapter 5: Heat Transfer & Fluid Mechanics in Welding
5.1 Fourier Conduction, Rosenthal Moving Heat Source & 2D vs. 3D Heat Flow 5.2 Adams Cooling Rate, the t8/5 Window & HAZ Peak-Temperature Distribution 5.3 Convection, Stefan-Boltzmann Radiation & Emissivity of Weld Surfaces 5.4 Arc Radiation Losses, Preheat Maintenance & PWHT Boundary Conditions 5.5 Fluid Statics, Bernoulli, Viscosity & Reynolds-Number Regimes 5.6 Gas Lens Mechanics, Buoyancy Effects & Torch Flow Design 5.7 Hyperbaric, Vacuum & Controlled-Atmosphere Welding Environments
7 Chapter 6: Electrical Engineering Principles for Welding Systems
6.1 DC and AC Waveforms, Polarity Thermodynamics & Welding Circuit Analysis 6.2 Joule Heating, Electrode Stickout Preheating & Circuit Voltage Distribution 6.3 Power Factor, Reactance, Impedance & Magnetic Transformer Principles 6.4 Lorentz Force, Electromagnetic Pinch Effect & Arc Blow
8 Chapter 7: Welding Heat Sources & Arc Physics
7.1 Volt-Ampere Characteristics, Operating Point, Self-Regulation & OCV Limits 7.2 Inductance, Slope Control & Dynamic Power-Source Response 7.3 Arc Fall Regions, Cathode Emission Mechanisms & Shielding-Gas Ionization 7.4 Maecker Plasma Jet, Degree of Ionization & Anode Heat Partitioning 7.5 Droplet Force Balance & Classification of Metal Transfer Regimes 7.6 Transition Current, Mode Comparison & Pulsed Waveform Design
9 Chapter 8: Arc Welding Processes & Parameter Controls
8.1 Shielded Metal Arc Welding (SMAW): Electrode Flux Chemistries & Variables 8.2 GMAW Process Physics, Transfer Modes & Shielding Gas Interactions 8.3 Solid, Metal-Cored & Flux-Cored Wires with CTWD and Parameter Envelopes 8.4 Gas Tungsten (GTAW) & Plasma Arc Welding (PAW): Electrodes & Keyholing 8.5 Submerged Arc Welding (SAW): Flux Basicity, Multi-Wire & High-Deposition Systems
10 Chapter 9: Advanced, Resistance & Solid-State Joining Processes
9.1 High-Energy-Density Beam Physics & Electron Beam Welding 9.2 Laser Beam Welding, EBW/LBW Comparison & Fiber Laser Parameter Derivation 9.3 Resistance Welding Physics, Electrode Materials & Spot Weld Sequence 9.4 Nugget Sizing, Seam and Projection Welding, and Lobe Curve Process Windows 9.5 Solid-State Joining: Friction Stir Welding (FSW), Explosion & Diffusion 9.6 Thermal Cutting & Gouging: Oxyfuel, Plasma Arc and Air Carbon Arc 9.7 High-Frequency, Flash, Stud & Ultrasonic Welding; Surfacing and Thermal Spray
11 Chapter 10: Physical & Transformation Metallurgy of Steels
10.1 Fe-Fe3C System, Crystal Lattices, c/a Ratio & Interstitial Solubility 10.2 Critical Temperatures, Invariant Reactions & the Lever Rule 10.3 Alloying Elements, the Gamma Loop & Phase-Fraction Calculations 10.4 TTT and CCT Diagrams, Constitutional Supercooling & Scheil Microsegregation 10.5 Non-Equilibrium Transformation Products & Martensite Modeling 10.6 HAZ Anatomy, Microstructural Sub-Zones & Multi-Pass Reheated Regions 10.7 HAZ Hardness Traverses, Toughness Gradients & Peak-Temperature Control
12 Chapter 11: Weldability, Cracking Mechanisms & Alloy Metallurgy
11.1 Hydrogen Cracking Conditions, Carbon Equivalent & Diffusible Hydrogen Control 11.2 Preheat, Interpass and Post-Heat Calculations for Cold-Crack Prevention 11.3 Solidification Cracking, Bead Aspect Ratio, Liquation & Lamellar Tearing 11.4 Lamellar Tearing Mitigation & Hot-Cracking Susceptibility Evaluation 11.5 Stainless Families, Schaeffler and WRC-1992 Diagrams, Ferrite Number & Sensitization 11.6 Duplex Stainless Metallurgy & Dissimilar-Metal Ferrite Prediction 11.7 Aluminum Oxide and Porosity Control, and Titanium Reactive-Metal Welding 11.8 Nickel Superalloys, Strain-Age Cracking & Guinier-Preston Aging Sequences
13 Chapter 12: Weldment Design, Stress Analysis & Joint Mechanics
12.1 AWS A2.4 Welding Symbol Anatomy, Symbol Library & Dimension Syntax 12.2 Joint Architecture, CJP versus PJP, and NDE Examination Symbols 12.3 Fillet and Groove Weld Sizing under Direct Stress in ASD and LRFD 12.4 Plug and Slot Welds, Stress Gradients & the Fillet Weld Break Test 12.5 Eccentric Loading Analysis: Elastic Vector Method vs Instantaneous Center 12.6 Fatigue Design of Welded Connections & Residual Stress/Distortion Control
14 Chapter 13: Non-Destructive Examination (NDE) & Discontinuity Analysis
13.1 Visual Testing Gages & Liquid Penetrant Capillary Mechanics 13.2 Magnetic Particle Testing: Flux Leakage, Field Geometry & Prod Amperage 13.3 Radiographic Physics, Geometric Unsharpness, Density & IQI Sensitivity 13.4 Computed and Digital Radiography & Radiographic Discontinuity Interpretation 13.5 Acoustic Wave Mechanics, Refraction & Angle-Beam Sound-Path Geometry 13.6 AWS D1.1 Decibel Rating, Phased Array & Time-of-Flight Diffraction
15 Chapter 14: Brazing, Soldering & Industrial Welding Safety
14.1 Brazing Thermodynamics, Capillary Wetting Physics & Joint Clearance 14.2 AWS A5.8 Brazing Filler Metals, FB Fluxes & Industrial Heating Processes 14.3 Soldering Fundamentals, Flux Chemistries & Intermetallic Formation 14.4 Hierarchy of Controls, Electric Shock Physics & Industrial Ventilation 14.5 Fume Exposure Limits, Arc Radiation, Hot Work and Confined-Space Entry 14.6 Arc-Generated Toxic Gases, Moving-Equipment Hazards & TWA Exposure Calculation
16 Chapter 15: Structural Fabrication & AWS D1.1 Code Implementation
15.1 AWS D1.1 Scope, Prequalification Limits, Base-Metal Groups & Matching Filler 15.2 Prequalified Joint Details, Backing Systems & Joint Specification Verification 15.3 Thermal Cut Edges, Fit-Up Tolerances & Minimum Preheat Requirements 15.4 Preheat Application Zones, Measurement Instrumentation & Fabrication Audits 15.5 PWHT Fundamentals, D1.1 Thermal Cycles & Visual Acceptance Criteria 15.6 D1.1 Nondestructive Examination Protocols, PWHT Scheduling & Visual Audit Practice
17 Chapter 16: Welding Procedure Qualification (WPS & PQR) per ASME IX & AWS B2.1
16.1 PQR versus WPS Hierarchy, Qualification Workflow & Standard Procedures 16.2 Manufacturer Responsibility, Subcontracting Limits & Multi-Process Qualification 16.3 Essential, Supplementary Essential and Nonessential Variables with Heat Input Mechanics 16.4 Waveform-Controlled Power Sources, Appendix H & Heat-Input Compliance 16.5 P-Numbers, Group Numbers, F-Numbers & A-Numbers 16.6 QW-451 Mechanical Test Protocols & Procedure Qualification Test Evaluation
18 Chapter 17: Filler Metal Specifications, Selection & Consumable Control
17.1 AWS A5 Architecture: SMAW, GMAW/GTAW and FCAW Consumable Classifications 17.2 SAW Wire-Flux Systems, Alloy Pickup & PWHT Property Effects 17.3 Stainless Filler Specifications, Solidification Modes & Dissimilar-Metal Joints 17.4 AWS A5.10 Aluminum Filler Selection & Dilution and Ferrite-Number Calculations 17.5 Consumable Storage, Conditioning Envelopes & Atmospheric Exposure Limits 17.6 Low-Hydrogen Designators, the Yurioka Parameter & Preheat Sizing
19 Chapter 18: Welder Performance Qualification, Quality Management & Welding Economics
18.1 Welder Qualification Philosophy, Test Positions & Thickness and Diameter Ranges 18.2 F-Number Hierarchy, Operator Qualification & Continuity Requirements 18.3 ISO 3834, Welding Coordination, Inspection Test Plans & Equipment Validation 18.4 EN 10204 Material Certification, Traceability & Heat-Input Nonconformance Auditing 18.5 Weld Cost Anatomy, Deposition Rates, Operating Factor & the Overwelding Law 18.6 Economic Optimization Strategies & Fabrication Cost Comparison
14.6 Arc-Generated Toxic Gases, Moving-Equipment Hazards & TWA Exposure Calculation
Key Takeaways Explain This Topic AI
Ozone, nitrogen oxides, carbon monoxide, phosgene and hydrogen fluoride are gases, so a particulate-filtering respirator offers no protection against them.
Phosgene forms when ultraviolet light from the arc decomposes chlorinated solvent vapour, which is why degreasing must be physically separated from arc welding.
Robotic welding cell safeguarding is governed by ANSI/RIA R15.06, and the welding engineer who specifies the cell owns the risk assessment.
An eight-hour time-weighted average is computed from the concentration in each task period weighted by its duration, not from the highest reading of the shift.
Last updated: September 2026
Toxic Gases Generated by the Arc
AWS B5.16 Clause 8.3.7 requires recognition of health hazards from fumes, toxic gases, noise and radiation . Fume particulate was covered above; the gaseous hazards are a separate exam topic because they are invisible, odourless at dangerous concentrations, and are produced by the arc itself rather than by the consumable.
Gas Formation mechanism Typical OSHA limit (29 CFR 1910.1000) Engineering control
Ozone (O3) UV photolysis of atmospheric oxygen by the arc; worst in GMAW/GTAW of aluminum and stainless under argon, and with high-current spray transfer 0.1 ppm Local exhaust at the arc; shield the arc from surrounding air; argon-helium or gas blends that reduce UV output
Nitrogen dioxide (NO2) Nitrogen and oxygen in air fixed by the arc or by plasma/oxyfuel cutting 5 ppm ceiling Local exhaust; never cut in a closed booth without extraction
Nitric oxide (NO) Same high-temperature air fixation; oxidizes to NO2 downstream 25 ppm As above
Carbon monoxide (CO) Thermal dissociation of CO2 shielding gas and of flux carbonates in the arc 50 ppm Extraction; critical in confined spaces and with 100% CO2 GMAW
Phosgene (COCl2) UV decomposition of chlorinated solvent vapour (trichloroethylene, perchloroethylene, methylene chloride) drifting into the arc 0.1 ppm Physically separate degreasing operations from all arc work; verify parts are dry before welding
Hydrogen fluoride (HF) Decomposition of fluoride-bearing electrode coatings and SAW fluxes 3 ppm (as F) Extraction, especially with low-hydrogen basic coatings
The phosgene pathway deserves particular emphasis because it is the one that kills people who believed they were working safely. Degreasing tanks using chlorinated solvents must never share ventilation or floor space with arc welding: the solvent vapour travels, the arc's ultraviolet output cracks it, and the resulting phosgene has a permissible limit 500 times lower than carbon monoxide's. ANSI Z49.1 addresses this by requiring that parts cleaned with chlorinated solvents be thoroughly dried before welding and that welding be located away from such operations.
Exam Trap: "Ozone is a fume." Ozone, NOx, CO, phosgene and HF are gases — they pass straight through a particulate-filtering respirator and are not captured by a fume-rated cartridge. Controlling them requires ventilation, source separation or supplied-air respiratory protection, never a dust/fume filter. Answer choices that propose an N95 or P100 for a gaseous hazard are always wrong.
Mechanical & Moving-Equipment Hazards
Clause 8.3.7 also lists moving equipment among the safety hazards a welding engineer must recognize. Modern welding cells are mechanized, and the mechanization — not the arc — causes most of the severe-injury events:
Positioners, turning rolls and manipulators. Rotating tables and turning rolls create crushing and in-running nip points between the workpiece and the rolls. Guarding, two-hand controls and travel limit switches are the accepted controls.
Robotic welding cells. Safeguarding is governed by ANSI/RIA R15.06 (harmonized with ISO 10218): perimeter fencing, interlocked gates, light curtains, safe-speed teach modes and emergency stops. A welding engineer specifying a cell owns the risk assessment, not only the weld schedule.
Energy isolation. Servicing any powered positioner, wire feeder, fixture actuator or exhaust fan requires lockout/tagout under OSHA 29 CFR 1910.147, including hydraulic and pneumatic stored energy, not just electrical.
Cranes, rigging and material handling. Dropped or swinging weldments cause crush injuries during fit-up; lifting lugs that were tacked rather than welded to a qualified procedure are a recurring failure mode.
Grinding and cutting equipment. Abrasive wheel guarding, correct wheel rating and eye protection under 29 CFR 1910.215 apply to the cleanup operations that surround every weld.
- Comprehensive Worked Engineering Example: LEV Airflow & 8-Hour TWA Fume Exposure
- Problem Statement
A welding workstation uses a flanged rectangular local exhaust hood (12 in × 18 in, area A = 1.50 ft²) positioned at a distance of X = 1.25 ft from a structural GMAW seam. Calculate the required volumetric flow rate Q (in CFM) to satisfy the OSHA mandatory capture velocity of V_c = 100 ft/min.
An industrial hygiene monitoring survey samples a welder fabricating 316L stainless steel vessels across an 8-hour shift. The personal breathing zone air sampler yields the following data:
Task 1 (SMAW with E316-16): Duration T_1 = 3.5 hours; Cr(VI) concentration C_1 = 8.40 μg/m3.
Task 2 (GTAW Root Pass): Duration T_2 = 2.5 hours; Cr(VI) concentration C_2 = 0.80 μg/m3.
Task 3 (Grinding / Setup): Duration T_3 = 2.0 hours; Cr(VI) concentration C_3 = 1.20 μg/m3.
Calculate the 8-hour Time-Weighted Average (TWA) exposure to Hexavalent Chromium. State whether the welder has exceeded the OSHA Action Level (2.5 μg/m3) or the OSHA Permissible Exposure Limit (5.0 μg/m3), and outline mandatory engineering and administrative interventions.
- Step-by-Step Engineering Solution
- Part 1: LEV Volumetric Flow Rate Calculation
- DallaValle equation for flanged hood: Q = 0.75 * V_c * (10 * X² + A)
- Given: V_c = 100 ft/min, X = 1.25 ft, A = 1.50 ft²: X² = (1.25)² = 1.5625 ft²
- 10 * X² + A = 10 * (1.5625) + 1.50 = 15.625 + 1.50 = 17.125 ft²
- Q = 0.75 * 100 * 17.125 = 75 * 17.125 = 1,284.38 CFM
Engineering Result: The exhaust fan must deliver at least 1,285 CFM of airflow through the ductwork.
Part 2: 8-Hour Time-Weighted Average (TWA) Calculation TWA = [Sum of (C_i * T_i)] / [Sum of T_i] = (C_1 * T_1 + C_2 * T_2 + C_3 * T_3) / 8.0 hours
- TWA = [(8.40 μg/m3 * 3.5 hr) + (0.80 μg/m3 * 2.5 hr) + (1.20 μg/m3 * 2.0 hr)] / 8.0 hr
- TWA = (29.40 + 2.00 + 2.40) / 8.0 = 33.80 / 8.0 = 4.225 μg/m3
Regulatory and Industrial Hygiene Evaluation:
OSHA Action Level (2.5 μg/m3): EXCEEDED. (4.225 > 2.5).
OSHA Permissible Exposure Limit (5.0 μg/m3): NOT EXCEEDED. (4.225 ≤ 5.0).
Mandatory Corrective Action per 29 CFR 1910.1026: Because the Action Level was breached, the employer is legally obligated to: (1) enroll the welder in an annual medical surveillance program, (2) perform periodic exposure monitoring every 6 months, (3) institute mandatory Cr(VI) hazard training, and (4) upgrade engineering controls (e.g., repositioning LEV extraction source capture closer to the SMAW station) to drive the TWA below the 2.5 μg/m3 threshold.
- Industrial Scenarios & Certified Welding Engineer Exam Pitfalls
- Real-World Field Disaster Scenario
A maintenance crew entered the ballast tank of an ocean barge to repair internal stiffener web cracks using SMAW. The crew ran high-pressure oxygen hoses into the tank to "freshen the air" and sweeten the humid atmosphere. Within 30 minutes, an arc spark bounced off a stiffener and landed on a worker's grease-stained leather glove. In the 28% oxygen-enriched environment, the leather glove and jacket exploded into intense, uncontrollable flames. Both welders suffered fatal third-degree burns before the attendant could react. Atmospheric testing had not been performed, and oxygen had been used as ventilation in violation of OSHA 1910.146 and ANSI Z49.1.
Common Exam Traps
Exam Trap 1: The 35-Foot Rule and Fire Watch Duration A standard exam question asks: "Under ANSI Z49.1 and OSHA 1910.252, what is the required combustible clearance and minimum post-welding fire watch duration?" The required clearance is 35 feet (10.7 meters) , and the minimum post-work duration is 30 minutes (never 15 minutes!).
Exam Trap 2: Oxygen Enrichment Boundary Questions frequently ask candidates to identify the maximum allowable oxygen concentration for safe confined space entry. Options often include 20.9%, 21.5%, 23.5%, and 25.0%. The correct statutory limit per OSHA 1910.146 is 23.5% . Any reading above 23.5% constitutes an oxygen-enriched atmosphere.
Exam Trap 3: SMAW vs. GTAW Hexavalent Chromium Candidates are often tricked into assuming that GTAW produces the most dangerous fumes because it welds high-purity stainless steels. In reality, SMAW and FCAW generate far higher fractions of Hexavalent Chromium than GTAW due to alkali metal salts in the flux coatings that chemically oxidize chromium into its hexavalent state.