Study guide
16.5 P-Numbers, Group Numbers, F-Numbers & A-Numbers
AWS CWEng Certified Welding Engineer Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & CWEng Exam Overview
About the CWEng Exam: Four Parts, 163 Questions & Testing Logistics Scoring, Composite Weighting, Eligibility & Five-Year Renewal How to Use This Guide & Build Your Open-Book Reference Set
2 Chapter 1: Mathematics & Statistics for Welding Engineers
1.1 Engineering Mathematics: Algebra, Trigonometry & Geometry in Weldments 1.2 Differential & Integral Calculus Fundamentals in Engineering Analysis 1.3 Applied Engineering Statistics, Population Distributions & Quality Metrics 1.4 Polynomial Equations, Conic Sections & Complex Numbers
3 Chapter 2: Physics Fundamentals & Mechanics
2.1 Unit Systems, Dimensional Analysis & Engineering Conversions 2.2 Mechanics: Statics, Equilibrium, Force Vectors & Moments 2.3 Work, Energy, Power & Mechanical Advantage in Welding Systems 2.4 Thermal Physics, Linear/Volumetric Expansion & Heat Capacity
4 Chapter 3: General & Physical Chemistry for Welding
3.1 Atomic Structure, Bonding & Solid-Solution Thermodynamics 3.2 Hume-Rothery Compatibility, Interstitial Strain & HSLA Microalloy Scavenging 3.3 Gas Laws, Dalton Partial Pressures, Arc Dissociation & Sieverts Law 3.4 Cylinder Capacity, Available Arc Time & Gas-Related Porosity Diagnosis 3.5 Redox Thermodynamics, Deoxidation & Slag-Metal Refining 3.6 Basicity Index Calculations, Toughness Prediction & Cryogenic Consumable Selection
5 Chapter 4: Strength of Materials & Mechanics of Materials
4.1 Engineering vs. True Stress-Strain, Elastic Constants & Z-Direction Ductility 4.2 Plane Stress vs. Plane Strain, Triaxial Restraint & Alloy Property Comparison 4.3 Beam Bending, Transverse Shear, Torsion & Mohr Circle Construction 4.4 Multiaxial Yield Criteria & Combined-Load Analysis of Welded Members 4.5 Fatigue Life, Weld-Toe Stress Concentration & Paris-Erdogan Crack Growth 4.6 LEFM Fracture Toughness, Ductile-Brittle Transition & Larson-Miller Creep 4.7 Comparative Failure-Mode Synthesis & Integrated Flaw and Creep Assessment
6 Chapter 5: Heat Transfer & Fluid Mechanics in Welding
5.1 Fourier Conduction, Rosenthal Moving Heat Source & 2D vs. 3D Heat Flow 5.2 Adams Cooling Rate, the t8/5 Window & HAZ Peak-Temperature Distribution 5.3 Convection, Stefan-Boltzmann Radiation & Emissivity of Weld Surfaces 5.4 Arc Radiation Losses, Preheat Maintenance & PWHT Boundary Conditions 5.5 Fluid Statics, Bernoulli, Viscosity & Reynolds-Number Regimes 5.6 Gas Lens Mechanics, Buoyancy Effects & Torch Flow Design 5.7 Hyperbaric, Vacuum & Controlled-Atmosphere Welding Environments
7 Chapter 6: Electrical Engineering Principles for Welding Systems
6.1 DC and AC Waveforms, Polarity Thermodynamics & Welding Circuit Analysis 6.2 Joule Heating, Electrode Stickout Preheating & Circuit Voltage Distribution 6.3 Power Factor, Reactance, Impedance & Magnetic Transformer Principles 6.4 Lorentz Force, Electromagnetic Pinch Effect & Arc Blow
8 Chapter 7: Welding Heat Sources & Arc Physics
7.1 Volt-Ampere Characteristics, Operating Point, Self-Regulation & OCV Limits 7.2 Inductance, Slope Control & Dynamic Power-Source Response 7.3 Arc Fall Regions, Cathode Emission Mechanisms & Shielding-Gas Ionization 7.4 Maecker Plasma Jet, Degree of Ionization & Anode Heat Partitioning 7.5 Droplet Force Balance & Classification of Metal Transfer Regimes 7.6 Transition Current, Mode Comparison & Pulsed Waveform Design
9 Chapter 8: Arc Welding Processes & Parameter Controls
8.1 Shielded Metal Arc Welding (SMAW): Electrode Flux Chemistries & Variables 8.2 GMAW Process Physics, Transfer Modes & Shielding Gas Interactions 8.3 Solid, Metal-Cored & Flux-Cored Wires with CTWD and Parameter Envelopes 8.4 Gas Tungsten (GTAW) & Plasma Arc Welding (PAW): Electrodes & Keyholing 8.5 Submerged Arc Welding (SAW): Flux Basicity, Multi-Wire & High-Deposition Systems
10 Chapter 9: Advanced, Resistance & Solid-State Joining Processes
9.1 High-Energy-Density Beam Physics & Electron Beam Welding 9.2 Laser Beam Welding, EBW/LBW Comparison & Fiber Laser Parameter Derivation 9.3 Resistance Welding Physics, Electrode Materials & Spot Weld Sequence 9.4 Nugget Sizing, Seam and Projection Welding, and Lobe Curve Process Windows 9.5 Solid-State Joining: Friction Stir Welding (FSW), Explosion & Diffusion 9.6 Thermal Cutting & Gouging: Oxyfuel, Plasma Arc and Air Carbon Arc 9.7 High-Frequency, Flash, Stud & Ultrasonic Welding; Surfacing and Thermal Spray
11 Chapter 10: Physical & Transformation Metallurgy of Steels
10.1 Fe-Fe3C System, Crystal Lattices, c/a Ratio & Interstitial Solubility 10.2 Critical Temperatures, Invariant Reactions & the Lever Rule 10.3 Alloying Elements, the Gamma Loop & Phase-Fraction Calculations 10.4 TTT and CCT Diagrams, Constitutional Supercooling & Scheil Microsegregation 10.5 Non-Equilibrium Transformation Products & Martensite Modeling 10.6 HAZ Anatomy, Microstructural Sub-Zones & Multi-Pass Reheated Regions 10.7 HAZ Hardness Traverses, Toughness Gradients & Peak-Temperature Control
12 Chapter 11: Weldability, Cracking Mechanisms & Alloy Metallurgy
11.1 Hydrogen Cracking Conditions, Carbon Equivalent & Diffusible Hydrogen Control 11.2 Preheat, Interpass and Post-Heat Calculations for Cold-Crack Prevention 11.3 Solidification Cracking, Bead Aspect Ratio, Liquation & Lamellar Tearing 11.4 Lamellar Tearing Mitigation & Hot-Cracking Susceptibility Evaluation 11.5 Stainless Families, Schaeffler and WRC-1992 Diagrams, Ferrite Number & Sensitization 11.6 Duplex Stainless Metallurgy & Dissimilar-Metal Ferrite Prediction 11.7 Aluminum Oxide and Porosity Control, and Titanium Reactive-Metal Welding 11.8 Nickel Superalloys, Strain-Age Cracking & Guinier-Preston Aging Sequences
13 Chapter 12: Weldment Design, Stress Analysis & Joint Mechanics
12.1 AWS A2.4 Welding Symbol Anatomy, Symbol Library & Dimension Syntax 12.2 Joint Architecture, CJP versus PJP, and NDE Examination Symbols 12.3 Fillet and Groove Weld Sizing under Direct Stress in ASD and LRFD 12.4 Plug and Slot Welds, Stress Gradients & the Fillet Weld Break Test 12.5 Eccentric Loading Analysis: Elastic Vector Method vs Instantaneous Center 12.6 Fatigue Design of Welded Connections & Residual Stress/Distortion Control
14 Chapter 13: Non-Destructive Examination (NDE) & Discontinuity Analysis
13.1 Visual Testing Gages & Liquid Penetrant Capillary Mechanics 13.2 Magnetic Particle Testing: Flux Leakage, Field Geometry & Prod Amperage 13.3 Radiographic Physics, Geometric Unsharpness, Density & IQI Sensitivity 13.4 Computed and Digital Radiography & Radiographic Discontinuity Interpretation 13.5 Acoustic Wave Mechanics, Refraction & Angle-Beam Sound-Path Geometry 13.6 AWS D1.1 Decibel Rating, Phased Array & Time-of-Flight Diffraction
15 Chapter 14: Brazing, Soldering & Industrial Welding Safety
14.1 Brazing Thermodynamics, Capillary Wetting Physics & Joint Clearance 14.2 AWS A5.8 Brazing Filler Metals, FB Fluxes & Industrial Heating Processes 14.3 Soldering Fundamentals, Flux Chemistries & Intermetallic Formation 14.4 Hierarchy of Controls, Electric Shock Physics & Industrial Ventilation 14.5 Fume Exposure Limits, Arc Radiation, Hot Work and Confined-Space Entry 14.6 Arc-Generated Toxic Gases, Moving-Equipment Hazards & TWA Exposure Calculation
16 Chapter 15: Structural Fabrication & AWS D1.1 Code Implementation
15.1 AWS D1.1 Scope, Prequalification Limits, Base-Metal Groups & Matching Filler 15.2 Prequalified Joint Details, Backing Systems & Joint Specification Verification 15.3 Thermal Cut Edges, Fit-Up Tolerances & Minimum Preheat Requirements 15.4 Preheat Application Zones, Measurement Instrumentation & Fabrication Audits 15.5 PWHT Fundamentals, D1.1 Thermal Cycles & Visual Acceptance Criteria 15.6 D1.1 Nondestructive Examination Protocols, PWHT Scheduling & Visual Audit Practice
17 Chapter 16: Welding Procedure Qualification (WPS & PQR) per ASME IX & AWS B2.1
16.1 PQR versus WPS Hierarchy, Qualification Workflow & Standard Procedures 16.2 Manufacturer Responsibility, Subcontracting Limits & Multi-Process Qualification 16.3 Essential, Supplementary Essential and Nonessential Variables with Heat Input Mechanics 16.4 Waveform-Controlled Power Sources, Appendix H & Heat-Input Compliance 16.5 P-Numbers, Group Numbers, F-Numbers & A-Numbers 16.6 QW-451 Mechanical Test Protocols & Procedure Qualification Test Evaluation
18 Chapter 17: Filler Metal Specifications, Selection & Consumable Control
17.1 AWS A5 Architecture: SMAW, GMAW/GTAW and FCAW Consumable Classifications 17.2 SAW Wire-Flux Systems, Alloy Pickup & PWHT Property Effects 17.3 Stainless Filler Specifications, Solidification Modes & Dissimilar-Metal Joints 17.4 AWS A5.10 Aluminum Filler Selection & Dilution and Ferrite-Number Calculations 17.5 Consumable Storage, Conditioning Envelopes & Atmospheric Exposure Limits 17.6 Low-Hydrogen Designators, the Yurioka Parameter & Preheat Sizing
19 Chapter 18: Welder Performance Qualification, Quality Management & Welding Economics
18.1 Welder Qualification Philosophy, Test Positions & Thickness and Diameter Ranges 18.2 F-Number Hierarchy, Operator Qualification & Continuity Requirements 18.3 ISO 3834, Welding Coordination, Inspection Test Plans & Equipment Validation 18.4 EN 10204 Material Certification, Traceability & Heat-Input Nonconformance Auditing 18.5 Weld Cost Anatomy, Deposition Rates, Operating Factor & the Overwelding Law 18.6 Economic Optimization Strategies & Fabrication Cost Comparison
16.5 P-Numbers, Group Numbers, F-Numbers & A-Numbers
Key Takeaways Explain This Topic AI
ASME Section IX base metal P-Numbers group alloys by weldability and chemical composition, while Group Numbers subdivide P-Numbers specifically for notch toughness qualification under QW/QB-422.
Filler metal F-Numbers (QW-432) group electrodes based on usability and operator manipulation characteristics, whereas A-Numbers (QW-442) classify the chemical composition of deposited ferrous weld metal.
Qualifying on one P-Number normally qualifies that P-Number, and specific cross-qualification between P-Numbers is permitted only where Section IX expressly states it.
A change in A-Number is an essential variable for ferrous weld metal because it changes deposit chemistry and therefore mechanical properties.
Group Numbers exist to control notch toughness, so they only become restrictive when the construction code requires impact testing.
Last updated: September 2026
16.3 P-Numbers, F-Numbers, A-Numbers & Mechanical Test Coupons
Quick Answer: ASME Section IX categorizes base metals into P-Numbers based on composition and weldability (e.g., P-No 1 carbon steels, P-No 8 austenitic stainless steels) and further subdivides them into Group Numbers when impact testing is required by construction codes. Filler metals are categorized by F-Numbers (QW-432) according to usability and slag system (F-1 through F-6 for steels) and by A-Numbers (QW-442) according to deposited ferrous weld metal chemical analysis (A-1 through A-12). Procedure qualification per QW-202 and Table QW-451.1 requires two transverse tension specimens and four guided bend specimens (or two root and two face bends for thin plate). Tension specimens must reach the specified minimum tensile strength (SMTS), but QW-153.1(d) accepts specimens failing in the base metal outside the weld at no more than 5% below SMTS. Guided bends evaluated per QW-163 reject any open discontinuity exceeding 1/8 in (3.2 mm). Charpy V-notch tests per QW-170 require specific notch placement across the weld metal centerline and HAZ.
Base Metal Grouping Taxonomy: P-Numbers & Group Numbers (QW/QB-422)
To avoid the unsustainable burden of qualifying individual procedures for thousands of distinct commercial metal alloys, ASME Section IX establishes the P-Number base metal grouping system in Table QW/QB-422 . Metals are grouped based on comparable chemical composition, weldability, mechanical properties, and metallurgical transformation behavior. ASME SECTION IX BASE METAL P-NUMBERS
- P-NO 1 P-NO 3 / 4 / 5 P-NO 8 P-NO 9 / 10H
- Carbon Steels Cr-Mo Alloy Steels Austenitic SS Cryogenic Ni & Duplex
- SA-36 - P-No 3: 0.5 Mo - SA-240 Type 304 - P-No 9A/B: 2-3.5% Ni
- SA-106 Gr B - P-No 4: 1.25Cr-0.5Mo - SA-240 Type 316 - P-No 9C: 9% Ni
- SA-516 Gr 70 - P-No 5A: 2.25Cr-1Mo - SA-240 Type 321 - P-No 10H: 2205 Duplex
- P-No 5B: 5Cr to 9Cr - SA-240 Type 347 - P-No 10I: 2507 Super Duplex
- P-No 5C: P91/P92 CSEF
- Primary P-Number Designations
P-No 1: Carbon-manganese construction and pressure vessel steels (e.g., SA-36, SA-106 Gr B, SA-516 Gr 60/70, SA-53).
P-No 3: Carbon-molybdenum (0.5% Mo) low-alloy steels (e.g., SA-335 Gr P1, SA-209).
P-No 4: 1.25% Cr – 0.5% Mo creep-resisting low-alloy steels (e.g., SA-387 Gr 11, SA-335 Gr P11).
P-No 5A, 5B, 5C: 2.25% Cr through 9% Cr alloys. P-No 5A includes 2.25Cr-1Mo (SA-335 P22); P-No 5B includes 5Cr and 9Cr (SA-335 P5, P9); P-No 5C governs Creep Strength Enhanced Ferritic (CSEF) martensitic steels like Grade 91 (SA-335 P91) and Grade 92.
P-No 6: High-chromium martensitic stainless steels (e.g., Type 410).
P-No 7: Ferritic stainless steels (e.g., Type 405, Type 430).
P-No 8: Chromium-nickel austenitic stainless steels (e.g., Type 304, 304L, 316, 316L, 321, 347).
P-No 9A, 9B, 9C: Nickel alloy steels for cryogenic service (2.25% to 9% Ni steels, SA-333 Gr 3, SA-553).
P-No 10H: Duplex and super duplex stainless steels (e.g., UNS S31803, S32205, S32750).
P-No 21 through 26: Aluminum and aluminum-base alloys.
P-No 41 through 49: Nickel and nickel-base alloys (Inconel 600, 625, Incoloy 800H, Hastelloy C-276).
P-No 51 through 53: Titanium and titanium-base alloys.
Group Numbers and Notch Toughness Rules (QW-403.5)
Within ferrous P-Numbers (P-No 1, 3, 4, 5, 9, 10, 11), base metals are further divided into Group Numbers assigned primarily according to tensile strength and deoxidation practice:
P-No 1 Group 1: Steels with minimum specified tensile strength < 70 ksi (e.g., SA-516 Gr 60, SA-106 Gr B).
P-No 1 Group 2: Steels with minimum specified tensile strength >= 70 ksi (e.g., SA-516 Gr 70, SA-537 Cl 1). +---------------------------------------------------------------------------------------------------------+
- | P-NUMBER VS. GROUP NUMBER QUALIFICATION SCOPE |
- +------------------------------------+----------------------------------+---------------------------------+
- | Toughness Requirement Status | Procedure Qualification Coupon | Qualified Base Metal Range |
- +------------------------------------+----------------------------------+---------------------------------+
- | NOT MANDATORY | Welded on P-No 1 Group 1 | Qualifies ALL P-No 1 |
- | (Standard Article II Qualification)| (e.g., SA-516 Gr 60) | (Group 1, Group 2, Group 3) |
- +------------------------------------+----------------------------------+---------------------------------+
- | MANDATORY (CVN Impact Required) | Welded on P-No 1 Group 1 | Qualifies ONLY P-No 1 Group 1 |
- | (Supplementary Essential QW-403.5) | (e.g., SA-516 Gr 60) | (DOES NOT qualify Group 2) |
- +------------------------------------+----------------------------------+---------------------------------+
- | MANDATORY (CVN Impact Required) | Welded on P-No 1 Group 2 | Qualifies ONLY P-No 1 Group 2 |
- | (Supplementary Essential QW-403.5) | (e.g., SA-516 Gr 70) | (DOES NOT qualify Group 1) |
- +------------------------------------+----------------------------------+---------------------------------+
Core Engineering Principle: The Group Number Toughness Barrier When notch toughness is not required by the construction code, qualification on any material in a P-Number qualifies all materials within that P-Number (QW-403.1). However, under supplementary essential variable QW-403.5 , when impact testing is required, qualification of a procedure on one Group Number qualifies only that specific Group Number. It does not qualify other Group Numbers within the same P-Number, nor does it qualify combinations unless specifically tested.
Unassigned Base Metals
Base metals not listed in Table QW/QB-422 (such as proprietary alloys or non-ASME specifications) are designated as unassigned metals . An unassigned metal must be qualified independently. Qualification of an unassigned metal qualifies only that specific specification, type, and grade.
Filler Metal Grouping: F-Numbers (QW-432) & A-Numbers (QW-442)
ASME Section IX classifies filler metals using two independent parameters: F-Numbers (which evaluate usability and operator manipulation characteristics) and A-Numbers (which evaluate the chemical composition of the deposited ferrous weld metal).
F-Numbers (Table QW-432)
F-Numbers group welding electrodes and rods based on their operational characteristics, coating formulation, and slag chemistry, significantly reducing procedure and performance qualification requirements. +-------------+---------------------------------------+---------------------------------------------------+
- | F-Number | Electrode Description & Flux System | Representative AWS Classifications |
- +-------------+---------------------------------------+---------------------------------------------------+
- | **F-1** | High-deposition, heavy iron-powder | EXX20, EXX24, EXX27, EXX28 |
- | **F-2** | Rutile coatings, general purpose | EXX12, EXX13, EXX14 |
- | **F-3** | Cellulosic coatings, deep penetration | EXX10, EXX11 (E6010, E7010) |
- | **F-4** | Basic low-hydrogen coatings | EXX15, EXX16, EXX18, EXX18M (E7018, E8018) |
- | **F-5** | Stainless steel covered electrodes | E3XX, E4XX series (E308L-16, E316L-16) |
- | **F-6** | Solid wires, cored wires, bare rods | All carbon & low-alloy GTAW/GMAW/FCAW/SAW wires |
- | | | (ER70S-6, E71T-1M, F7A2-EM12K) |
- | **F-41-46** | Nickel and nickel-alloy consumables | ERNiCr-3 (Inconel 82), ENiCrMo-3 (Inconel 625) |
- +-------------+---------------------------------------+---------------------------------------------------+
Under QW-404.4, changing from one F-Number to another F-Number (e.g., qualifying with an F-3 E6010 electrode and switching to an F-4 E7018 electrode) is an essential variable for procedure qualification that mandates a new PQR.
A-Numbers (Table QW-442)
A-Numbers classify the chemical analysis of the deposited weld metal for ferrous alloys . They do not apply to nonferrous metals (nickel, aluminum, copper). +-------------+---------------------------------------+---------------------------------------------------+
- | A-Number | Weld Metal Deposit Type | Nominal Chemical Composition (Weight %) |
- +-------------+---------------------------------------+---------------------------------------------------+
- | **A-1** | Mild Carbon Steel | C: 0.15% max, Cr: ---, Mo: ---, Ni: ---, Mn: 1.6% |
- | **A-2** | Carbon-Molybdenum (C-Mo) | C: 0.15%, Mo: 0.40–0.65% |
- | **A-3** | Chromium-Molybdenum (0.5Cr-0.5Mo) | Cr: 0.40–1.25%, Mo: 0.40–0.65% |
- | **A-4** | Chromium-Molybdenum (2Cr-1Mo) | Cr: 1.75–3.00%, Mo: 0.40–1.50% |
- | **A-5** | High Cr-Mo (5Cr to 10Cr) | Cr: 4.00–10.5%, Mo: 0.40–1.50% |
- | **A-8** | Chromium-Nickel Austenitic (18Cr-8Ni) | Cr: 14.5–30.0%, Ni: 7.5–15.0% (308, 316) |
- | **A-9** | Chromium-Nickel Austenitic (High Cr) | Cr: 19.0–30.0%, Ni: 15.0–37.0% (309, 310) |
- +-------------+---------------------------------------+---------------------------------------------------+
Per QW-404.5, a change in the weld metal chemical composition from one A-Number to any other A-Number is an essential variable . The A-Number may be determined by chemical analysis of the test coupon weld deposit or from the filler metal manufacturer's certified material test report (CMTR) matching the AWS specification.