Study guide
17.2 SAW Wire-Flux Systems, Alloy Pickup & PWHT Property Effects
AWS CWEng Certified Welding Engineer Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & CWEng Exam Overview
About the CWEng Exam: Four Parts, 163 Questions & Testing Logistics Scoring, Composite Weighting, Eligibility & Five-Year Renewal How to Use This Guide & Build Your Open-Book Reference Set
2 Chapter 1: Mathematics & Statistics for Welding Engineers
1.1 Engineering Mathematics: Algebra, Trigonometry & Geometry in Weldments 1.2 Differential & Integral Calculus Fundamentals in Engineering Analysis 1.3 Applied Engineering Statistics, Population Distributions & Quality Metrics 1.4 Polynomial Equations, Conic Sections & Complex Numbers
3 Chapter 2: Physics Fundamentals & Mechanics
2.1 Unit Systems, Dimensional Analysis & Engineering Conversions 2.2 Mechanics: Statics, Equilibrium, Force Vectors & Moments 2.3 Work, Energy, Power & Mechanical Advantage in Welding Systems 2.4 Thermal Physics, Linear/Volumetric Expansion & Heat Capacity
4 Chapter 3: General & Physical Chemistry for Welding
3.1 Atomic Structure, Bonding & Solid-Solution Thermodynamics 3.2 Hume-Rothery Compatibility, Interstitial Strain & HSLA Microalloy Scavenging 3.3 Gas Laws, Dalton Partial Pressures, Arc Dissociation & Sieverts Law 3.4 Cylinder Capacity, Available Arc Time & Gas-Related Porosity Diagnosis 3.5 Redox Thermodynamics, Deoxidation & Slag-Metal Refining 3.6 Basicity Index Calculations, Toughness Prediction & Cryogenic Consumable Selection
5 Chapter 4: Strength of Materials & Mechanics of Materials
4.1 Engineering vs. True Stress-Strain, Elastic Constants & Z-Direction Ductility 4.2 Plane Stress vs. Plane Strain, Triaxial Restraint & Alloy Property Comparison 4.3 Beam Bending, Transverse Shear, Torsion & Mohr Circle Construction 4.4 Multiaxial Yield Criteria & Combined-Load Analysis of Welded Members 4.5 Fatigue Life, Weld-Toe Stress Concentration & Paris-Erdogan Crack Growth 4.6 LEFM Fracture Toughness, Ductile-Brittle Transition & Larson-Miller Creep 4.7 Comparative Failure-Mode Synthesis & Integrated Flaw and Creep Assessment
6 Chapter 5: Heat Transfer & Fluid Mechanics in Welding
5.1 Fourier Conduction, Rosenthal Moving Heat Source & 2D vs. 3D Heat Flow 5.2 Adams Cooling Rate, the t8/5 Window & HAZ Peak-Temperature Distribution 5.3 Convection, Stefan-Boltzmann Radiation & Emissivity of Weld Surfaces 5.4 Arc Radiation Losses, Preheat Maintenance & PWHT Boundary Conditions 5.5 Fluid Statics, Bernoulli, Viscosity & Reynolds-Number Regimes 5.6 Gas Lens Mechanics, Buoyancy Effects & Torch Flow Design 5.7 Hyperbaric, Vacuum & Controlled-Atmosphere Welding Environments
7 Chapter 6: Electrical Engineering Principles for Welding Systems
6.1 DC and AC Waveforms, Polarity Thermodynamics & Welding Circuit Analysis 6.2 Joule Heating, Electrode Stickout Preheating & Circuit Voltage Distribution 6.3 Power Factor, Reactance, Impedance & Magnetic Transformer Principles 6.4 Lorentz Force, Electromagnetic Pinch Effect & Arc Blow
8 Chapter 7: Welding Heat Sources & Arc Physics
7.1 Volt-Ampere Characteristics, Operating Point, Self-Regulation & OCV Limits 7.2 Inductance, Slope Control & Dynamic Power-Source Response 7.3 Arc Fall Regions, Cathode Emission Mechanisms & Shielding-Gas Ionization 7.4 Maecker Plasma Jet, Degree of Ionization & Anode Heat Partitioning 7.5 Droplet Force Balance & Classification of Metal Transfer Regimes 7.6 Transition Current, Mode Comparison & Pulsed Waveform Design
9 Chapter 8: Arc Welding Processes & Parameter Controls
8.1 Shielded Metal Arc Welding (SMAW): Electrode Flux Chemistries & Variables 8.2 GMAW Process Physics, Transfer Modes & Shielding Gas Interactions 8.3 Solid, Metal-Cored & Flux-Cored Wires with CTWD and Parameter Envelopes 8.4 Gas Tungsten (GTAW) & Plasma Arc Welding (PAW): Electrodes & Keyholing 8.5 Submerged Arc Welding (SAW): Flux Basicity, Multi-Wire & High-Deposition Systems
10 Chapter 9: Advanced, Resistance & Solid-State Joining Processes
9.1 High-Energy-Density Beam Physics & Electron Beam Welding 9.2 Laser Beam Welding, EBW/LBW Comparison & Fiber Laser Parameter Derivation 9.3 Resistance Welding Physics, Electrode Materials & Spot Weld Sequence 9.4 Nugget Sizing, Seam and Projection Welding, and Lobe Curve Process Windows 9.5 Solid-State Joining: Friction Stir Welding (FSW), Explosion & Diffusion 9.6 Thermal Cutting & Gouging: Oxyfuel, Plasma Arc and Air Carbon Arc 9.7 High-Frequency, Flash, Stud & Ultrasonic Welding; Surfacing and Thermal Spray
11 Chapter 10: Physical & Transformation Metallurgy of Steels
10.1 Fe-Fe3C System, Crystal Lattices, c/a Ratio & Interstitial Solubility 10.2 Critical Temperatures, Invariant Reactions & the Lever Rule 10.3 Alloying Elements, the Gamma Loop & Phase-Fraction Calculations 10.4 TTT and CCT Diagrams, Constitutional Supercooling & Scheil Microsegregation 10.5 Non-Equilibrium Transformation Products & Martensite Modeling 10.6 HAZ Anatomy, Microstructural Sub-Zones & Multi-Pass Reheated Regions 10.7 HAZ Hardness Traverses, Toughness Gradients & Peak-Temperature Control
12 Chapter 11: Weldability, Cracking Mechanisms & Alloy Metallurgy
11.1 Hydrogen Cracking Conditions, Carbon Equivalent & Diffusible Hydrogen Control 11.2 Preheat, Interpass and Post-Heat Calculations for Cold-Crack Prevention 11.3 Solidification Cracking, Bead Aspect Ratio, Liquation & Lamellar Tearing 11.4 Lamellar Tearing Mitigation & Hot-Cracking Susceptibility Evaluation 11.5 Stainless Families, Schaeffler and WRC-1992 Diagrams, Ferrite Number & Sensitization 11.6 Duplex Stainless Metallurgy & Dissimilar-Metal Ferrite Prediction 11.7 Aluminum Oxide and Porosity Control, and Titanium Reactive-Metal Welding 11.8 Nickel Superalloys, Strain-Age Cracking & Guinier-Preston Aging Sequences
13 Chapter 12: Weldment Design, Stress Analysis & Joint Mechanics
12.1 AWS A2.4 Welding Symbol Anatomy, Symbol Library & Dimension Syntax 12.2 Joint Architecture, CJP versus PJP, and NDE Examination Symbols 12.3 Fillet and Groove Weld Sizing under Direct Stress in ASD and LRFD 12.4 Plug and Slot Welds, Stress Gradients & the Fillet Weld Break Test 12.5 Eccentric Loading Analysis: Elastic Vector Method vs Instantaneous Center 12.6 Fatigue Design of Welded Connections & Residual Stress/Distortion Control
14 Chapter 13: Non-Destructive Examination (NDE) & Discontinuity Analysis
13.1 Visual Testing Gages & Liquid Penetrant Capillary Mechanics 13.2 Magnetic Particle Testing: Flux Leakage, Field Geometry & Prod Amperage 13.3 Radiographic Physics, Geometric Unsharpness, Density & IQI Sensitivity 13.4 Computed and Digital Radiography & Radiographic Discontinuity Interpretation 13.5 Acoustic Wave Mechanics, Refraction & Angle-Beam Sound-Path Geometry 13.6 AWS D1.1 Decibel Rating, Phased Array & Time-of-Flight Diffraction
15 Chapter 14: Brazing, Soldering & Industrial Welding Safety
14.1 Brazing Thermodynamics, Capillary Wetting Physics & Joint Clearance 14.2 AWS A5.8 Brazing Filler Metals, FB Fluxes & Industrial Heating Processes 14.3 Soldering Fundamentals, Flux Chemistries & Intermetallic Formation 14.4 Hierarchy of Controls, Electric Shock Physics & Industrial Ventilation 14.5 Fume Exposure Limits, Arc Radiation, Hot Work and Confined-Space Entry 14.6 Arc-Generated Toxic Gases, Moving-Equipment Hazards & TWA Exposure Calculation
16 Chapter 15: Structural Fabrication & AWS D1.1 Code Implementation
15.1 AWS D1.1 Scope, Prequalification Limits, Base-Metal Groups & Matching Filler 15.2 Prequalified Joint Details, Backing Systems & Joint Specification Verification 15.3 Thermal Cut Edges, Fit-Up Tolerances & Minimum Preheat Requirements 15.4 Preheat Application Zones, Measurement Instrumentation & Fabrication Audits 15.5 PWHT Fundamentals, D1.1 Thermal Cycles & Visual Acceptance Criteria 15.6 D1.1 Nondestructive Examination Protocols, PWHT Scheduling & Visual Audit Practice
17 Chapter 16: Welding Procedure Qualification (WPS & PQR) per ASME IX & AWS B2.1
16.1 PQR versus WPS Hierarchy, Qualification Workflow & Standard Procedures 16.2 Manufacturer Responsibility, Subcontracting Limits & Multi-Process Qualification 16.3 Essential, Supplementary Essential and Nonessential Variables with Heat Input Mechanics 16.4 Waveform-Controlled Power Sources, Appendix H & Heat-Input Compliance 16.5 P-Numbers, Group Numbers, F-Numbers & A-Numbers 16.6 QW-451 Mechanical Test Protocols & Procedure Qualification Test Evaluation
18 Chapter 17: Filler Metal Specifications, Selection & Consumable Control
17.1 AWS A5 Architecture: SMAW, GMAW/GTAW and FCAW Consumable Classifications 17.2 SAW Wire-Flux Systems, Alloy Pickup & PWHT Property Effects 17.3 Stainless Filler Specifications, Solidification Modes & Dissimilar-Metal Joints 17.4 AWS A5.10 Aluminum Filler Selection & Dilution and Ferrite-Number Calculations 17.5 Consumable Storage, Conditioning Envelopes & Atmospheric Exposure Limits 17.6 Low-Hydrogen Designators, the Yurioka Parameter & Preheat Sizing
19 Chapter 18: Welder Performance Qualification, Quality Management & Welding Economics
18.1 Welder Qualification Philosophy, Test Positions & Thickness and Diameter Ranges 18.2 F-Number Hierarchy, Operator Qualification & Continuity Requirements 18.3 ISO 3834, Welding Coordination, Inspection Test Plans & Equipment Validation 18.4 EN 10204 Material Certification, Traceability & Heat-Input Nonconformance Auditing 18.5 Weld Cost Anatomy, Deposition Rates, Operating Factor & the Overwelding Law 18.6 Economic Optimization Strategies & Fabrication Cost Comparison
17.2 SAW Wire-Flux Systems, Alloy Pickup & PWHT Property Effects
Key Takeaways Explain This Topic AI
Submerged arc welding (SAW) per AWS A5.17 and A5.23 specifies wire-flux combinations (e.g., F7A2-EM12K), where neutral fluxes maintain consistent weld metal chemistry across voltage variations, whereas active fluxes cause dangerous Mn and Si alloy accumulation in multi-pass welds.
Submerged arc flux and wire are classified as a system because the flux contributes alloying, so a wire designation alone does not define the deposit.
An active flux adds manganese and silicon in a way that varies with arc voltage, which is why voltage must be tightly controlled on multi-pass submerged arc welds.
A neutral flux keeps deposit chemistry essentially independent of voltage and is therefore preferred for thick multi-pass joints.
Consumable certifications state whether properties are as-welded or post-weld heat treated, and the two conditions can differ substantially in strength and toughness.
Last updated: September 2026
AWS A5.17 & AWS A5.23: Submerged Arc Wire-Flux Systems
Submerged Arc Welding (SAW) differs fundamentally from gas-shielded or coated processes: the electrode and the flux are classified together as a complete functional system . An electrode classified with Flux A will produce radically different weld metal mechanical properties and chemistry when paired with Flux B. AWS A5.17 SAW SYSTEM NOMENCLATURE
- F 7 A 2 - E M12 K
- | | | | | | |
- Flux Tensile Condition CVN Electrode Manganese Killed
- (x10 ksi) A = As-Weld 20 ft·lbf Solid Wire M = Med Mn (Silicon
- P = PWHT @-20°F (0.8-1.25%) Deoxidized)
- Low-Alloy SAW Systems (AWS A5.23)
AWS A5.23 incorporates two compositional suffixes: the first designates the solid or composite wire, while the second designates the chemical composition of the deposited weld metal: F 8 A 4 − E A 2 − A 2 \mathbf{F8A4-EA2-A2} F8A4 − EA2 − A2
F8 : 80–100 ksi tensile strength.
A : As-welded condition.
4 : 20 ft·lbf CVN at -40°F (-40°C).
EA2 : Solid wire containing 0.5% Mo.
-A2 : Deposited weld metal chemical composition meets the A2 class (0.5% Mo).
Active Flux vs. Neutral Flux Dynamics
Understanding flux behavior is one of the most heavily tested areas on the CWEng exam: +-----------------------------------------------------------------------------------------+
- | ACTIVE VS. NEUTRAL SAW FLUXES |
- +------------------------------------+----------------------------------------------------+
- | Characteristic | Active Flux | Neutral Flux |
- +------------------------------------+-------------------------+--------------------------+
- | Alloying Additions (Mn, Si) | High (deliberately | Negligible (maintains |
- | | added to flux matrix) | balance without alloying)|
- | Voltage Sensitivity | Extreme: higher voltage | Negligible: chemistry |
- | | burns more flux, adding | remains stable over |
- | | excessive Mn and Si | wide voltage window |
- | Maximum Plate Thickness / Passes | Single-pass or limited | Unlimited multi-pass |
- | | two-pass welds only | groove welds on heavy |
- | | (t <= 3/16" to 1/2") | plates (unlimited t) |
- | Primary Failure Mode if Misused | High hardness (>350 HV),| Oxidation or wormhole |
- | | microcracking, and low | porosity if applied over |
- | | CVN in multi-pass welds | uncleaned, heavy scale |
- +------------------------------------+-------------------------+--------------------------+
In an active flux, the recovery of manganese and silicon is directly proportional to the quantity of flux melted per unit length of weld. Because arc voltage governs arc length, increasing the arc voltage increases the flux consumption ratio phi = M_flux / M_wire: Δ [ % M n ] ∝ V arc ⋅ ( M flux M wire ) \Delta [\%Mn] \propto V_{\text{arc}} \cdot \left(\frac{M_{\text{flux}}}{M_{\text{wire}}}\right) Δ [ % M n ] ∝ V arc ⋅ ( M wire M flux )
If an operator increases arc voltage from 28 V to 35 V on a multi-pass joint using an active flux, weld metal manganese can spike from 1.20% to over 2.50%, and silicon can exceed 1.00%. The resulting weld metal transforms into brittle, untempered martensite, causing catastrophic cold cracking under restraint.
Mechanical Property Requirements & PWHT Effects
AWS A5 specifications mandate rigid tensile, yield, elongation, and Charpy V-notch toughness thresholds:
AWS Spec Classification Tensile Strength (ksi / MPa) Yield Strength min (ksi / MPa) Elongation min (%) CVN Impact Energy (min) PWHT Condition
- A5.1 E7018 70 / 483 58 / 400 22% 20 ft·lbf @ -20°F (-29°C) As-Welded
- A5.1 E7018-1 70 / 483 58 / 400 22% 20 ft·lbf @ -45°F (-43°C) As-Welded
- A5.5 E8018-C3 80 / 552 68–80 / 469–552 24% 20 ft·lbf @ -40°F (-40°C) As-Welded
- A5.5 E9018-B3 90 / 621 77 / 531 17% None specified by A5.5 PWHT: 1275°F (690°C) for 1 hr
- A5.18 ER70S-6 70 / 483 58 / 400 22% 20 ft·lbf @ -20°F (-29°C) As-Welded
- A5.20 E71T-1C / -1M 70–95 / 483–655 58 / 400 22% 20 ft·lbf @ 0°F (-18°C) As-Welded
- A5.20 E71T-8 70–95 / 483–655 58 / 400 22% 20 ft·lbf @ -20°F (-29°C) As-Welded
- A5.29 E81T1-Ni1M 80–100 / 552–689 68–80 / 469–552 19% 20 ft·lbf @ -40°F (-40°C) As-Welded
- A5.17 F7A2-EM12K 70–95 / 483–655 58 / 400 22% 20 ft·lbf @ -20°F (-29°C) As-Welded
- A5.23 F8A4-EA2-A2 80–100 / 552–689 68 / 469 20% 20 ft·lbf @ -40°F (-40°C) As-Welded
- Influence of Postweld Heat Treatment (PWHT)
Postweld heat treatment relieves residual stresses and tempers hard microstructures. However, for plain carbon-manganese weld metals, extended PWHT holding times can result in significant loss of tensile and yield strength (often dropping 5–10 ksi due to subcritical carbide coarsening and dislocation recovery) and may degrade CVN toughness if step-cooling induces temper embrittlement.
- Comprehensive Worked Engineering Example: SAW Flux Selection & Alloy Pickup Calculation
- Problem Statement
A pressure vessel manufacturer is welding a 38 mm thick longitudinal shell seam in ASTM A516 Grade 70 normalized plate. The joint is a symmetrical double-V groove requiring 14 passes. The welding supervisor proposes using an existing shop inventory of Submerged Arc flux designated as an active flux paired with an AWS A5.17 EM12K wire (0.10% C, 1.05% Mn, 0.22% Si). The qualified welding parameters specify 32 V, 550 A, and 450 mm/min.
From empirical flux calibration curves, the active flux transfers manganese and silicon to the weld metal according to the flux-to-wire consumption ratio phi = M_flux / M_wire: ϕ = 0.035 ⋅ V arc − 0.22 \phi = 0.035 \cdot V_{\text{arc}} - 0.22 ϕ = 0.035 ⋅ V arc − 0.22
The incremental alloy recovery into the deposit is: Δ % M n = 0.85 ⋅ ϕ \Delta \%Mn = 0.85 \cdot \phi Δ% M n = 0.85 ⋅ ϕ Δ % S i = 0.60 ⋅ ϕ \Delta \%Si = 0.60 \cdot \phi Δ% S i = 0.60 ⋅ ϕ
Assuming base metal dilution is D = 0.30 (30%), with base metal chemistry of 0.20% C, 1.20% Mn, and 0.25% Si:
Compute the flux consumption ratio phi at 32 V.
Calculate the resulting weld metal Mn and Si content for Pass 1 (diluted by base metal).
Calculate the steady-state weld metal Mn and Si content in Pass 8 (fill pass where dilution comes entirely from prior weld passes, D_weld = 0.30).
Evaluate compliance with AWS D1.1 Clause 5.6 / ASME Section VIII rules regarding active fluxes. DOUBLE-V GROOVE PASS PROFILE
- Plate Surface ================================ Plate Surface
- | Pass 14 Pass 13 /
| Pass 8 (Diluted from / <-- Fill Passes:
| Pass 7 Pass 6) / Mn & Si accumulate
| Pass 1 (Root Pass) / from active flux!
- +-------------------+
- | ASTM A516 Gr 70 |
- Step-by-Step Engineering Solution
Step 1: Compute Flux Consumption Ratio (phi) ϕ = 0.035 ( 32 ) − 0.22 = 1.12 − 0.22 = 0.90 \phi = 0.035(32) - 0.22 = 1.12 - 0.22 = 0.90 ϕ = 0.035 ( 32 ) − 0.22 = 1.12 − 0.22 = 0.90
For every 1.00 kg of wire consumed, 0.90 kg of active flux is melted.
Step 2: Calculate Alloy Transfer Increments Δ % M n = 0.85 × 0.90 = 0.765 % Mn \Delta \%Mn = 0.85 \times 0.90 = 0.765\%\text{ Mn} Δ% M n = 0.85 × 0.90 = 0.765% Mn Δ % S i = 0.60 × 0.90 = 0.540 % Si \Delta \%Si = 0.60 \times 0.90 = 0.540\%\text{ Si} Δ% S i = 0.60 × 0.90 = 0.540% Si
Step 3: Calculate Pass 1 Composition (Root Pass) In Pass 1, dilution from the base metal is D = 0.30, and consumable contribution is (1 - D) = 0.70: % M n deposit, pass 1 = D ( % M n base ) + ( 1 − D ) ( % M n wire + Δ % M n ) \%Mn_{\text{deposit, pass 1}} = D(\%Mn_{\text{base}}) + (1 - D)(\%Mn_{\text{wire}} + \Delta \%Mn) % M n deposit, pass 1 = D ( % M n base ) + ( 1 − D ) ( % M n wire + Δ% M n ) % M n deposit, pass 1 = 0.30 ( 1.20 ) + 0.70 ( 1.05 + 0.765 ) = 0.360 + 0.70 ( 1.815 ) = 0.360 + 1.2705 = 1.63 % Mn \%Mn_{\text{deposit, pass 1}} = 0.30(1.20) + 0.70(1.05 + 0.765) = 0.360 + 0.70(1.815) = 0.360 + 1.2705 = 1.63\%\text{ Mn} % M n deposit, pass 1 = 0.30 ( 1.20 ) + 0.70 ( 1.05 + 0.765 ) = 0.360 + 0.70 ( 1.815 ) = 0.360 + 1.2705 = 1.63% Mn % S i deposit, pass 1 = D ( % S i base ) + ( 1 − D ) ( % S i wire + Δ % S i ) \%Si_{\text{deposit, pass 1}} = D(\%Si_{\text{base}}) + (1 - D)(\%Si_{\text{wire}} + \Delta \%Si) % S i deposit, pass 1 = D ( % S i base ) + ( 1 − D ) ( % S i wire + Δ% S i ) % S i deposit, pass 1 = 0.30 ( 0.25 ) + 0.70 ( 0.22 + 0.540 ) = 0.075 + 0.70 ( 0.760 ) = 0.075 + 0.532 = 0.61 % Si \%Si_{\text{deposit, pass 1}} = 0.30(0.25) + 0.70(0.22 + 0.540) = 0.075 + 0.70(0.760) = 0.075 + 0.532 = 0.61\%\text{ Si} % S i deposit, pass 1 = 0.30 ( 0.25 ) + 0.70 ( 0.22 + 0.540 ) = 0.075 + 0.70 ( 0.760 ) = 0.075 + 0.532 = 0.61% Si
Step 4: Calculate Pass 8 Composition (Multi-pass Steady-State Accumulation) In multi-pass welding, subsequent passes dilute prior weld passes. At steady state, dilution D from preceding passes with identical consumable inputs leads to the undiluted weld metal composition: % M n steady = % M n wire + Δ % M n = 1.05 % + 0.765 % = 1.815 % Mn \%Mn_{\text{steady}} = \%Mn_{\text{wire}} + \Delta \%Mn = 1.05\% + 0.765\% = 1.815\%\text{ Mn} % M n steady = % M n wire + Δ% M n = 1.05% + 0.765% = 1.815% Mn % S i steady = % S i wire + Δ % S i = 0.22 % + 0.540 % = 0.760 % Si \%Si_{\text{steady}} = \%Si_{\text{wire}} + \Delta \%Si = 0.22\% + 0.540\% = 0.760\%\text{ Si} % S i steady = % S i wire + Δ% S i = 0.22% + 0.540% = 0.760% Si
If the operator allows arc voltage to wander up to 36 V to widen the cap pass: ϕ 36 V = 0.035 ( 36 ) − 0.22 = 1.26 − 0.22 = 1.04 \phi_{36V} = 0.035(36) - 0.22 = 1.26 - 0.22 = 1.04 ϕ 36 V = 0.035 ( 36 ) − 0.22 = 1.26 − 0.22 = 1.04 % M n cap = 1.05 + 0.85 ( 1.04 ) = 1.05 + 0.884 = 1.934 % Mn \%Mn_{\text{cap}} = 1.05 + 0.85(1.04) = 1.05 + 0.884 = 1.934\%\text{ Mn} % M n cap = 1.05 + 0.85 ( 1.04 ) = 1.05 + 0.884 = 1.934% Mn % S i cap = 0.22 + 0.60 ( 1.04 ) = 0.22 + 0.624 = 0.844 % Si \%Si_{\text{cap}} = 0.22 + 0.60(1.04) = 0.22 + 0.624 = 0.844\%\text{ Si} % S i cap = 0.22 + 0.60 ( 1.04 ) = 0.22 + 0.624 = 0.844% Si
Step 5: Metallurgical & Code Evaluation
The steady-state silicon content reaches 0.76–0.84%. Under AWS A5.17 and ASME Section VIII Div 1, silicon in structural weld deposits is typically restricted to <= 0.80% because excess silicon forms coarse silicate films and embrittles the matrix.
Manganese exceeds 1.80–1.93%, significantly increasing the Carbon Equivalent (CE) and hardenability: C E = C + M n 6 + C r + M o + V 5 + N i + C u 15 = 0.12 + 1.93 6 = 0.12 + 0.322 = 0.442 CE = C + \frac{Mn}{6} + \frac{Cr+Mo+V}{5} + \frac{Ni+Cu}{15} = 0.12 + \frac{1.93}{6} = 0.12 + 0.322 = 0.442 CE = C + 6 M n + 5 C r + M o + V + 15 N i + C u = 0.12 + 6 1.93 = 0.12 + 0.322 = 0.442
AWS D1.1 Clause 5.3 explicitly prohibits the use of active fluxes in multi-pass welds exceeding 3/16 in (5 mm) thickness. The proposed procedure must be REJECTED . The engineer must mandate a neutral flux conforming to AWS A5.17 (e.g., F7A2-EM12K with neutral bonded or fused flux).
- Industrial Scenarios & Certified Welding Engineer Exam Traps
- Real-World Field Disaster Scenario
A fabricator constructing heavy box columns for a 45-story commercial tower switched from an AWS A5.20 E71T-1C gas-shielded FCAW wire to an AWS A5.20 E71T-11 self-shielded wire on a night shift to eliminate gas cylinder handling. The column flange thickness was 2.5 in (63 mm). Within 48 hours, catastrophic full-length centerline cracking occurred down the core of every column seam. The failure investigation revealed two fatal engineering errors:
AWS A5.20 Table 1 Limitation: E71T-11 is explicitly restricted to a maximum plate thickness of 3/8 in (9.5 mm) due to high residual aluminum deoxidizers and lack of notch toughness.
Applying E71T-11 to 2.5 in highly restrained plate generated a coarse columnar microstructure with zero ductility, triggering immediate solidification and delayed cold cracking under transverse shrinkage stresses.
Certified Welding Engineer Exam Traps
Exam Trap 1: Active vs. Neutral Flux Voltage Sensitivity Exam writers frequently ask: "An operator notices slag sticking during SAW multi-pass groove welding and increases the arc voltage from 30 V to 37 V while using an active flux. What is the metallurgical impact on the deposited weld metal?" Candidates mistakenly think higher voltage merely widens the bead. The true engineering answer: Active flux consumption increases, driving excessive manganese and silicon into the weld puddle, causing extreme hardness (> 300 HV) and brittle notch sensitivity.
Exam Trap 2: Suffix Designation in AWS A5.23 vs. A5.5 In AWS A5.5 (SMAW), -B2 indicates the chemical composition of the deposited weld metal. In AWS A5.23 (SAW), a classification like F8A4-EB2-B2 has two -B2 suffixes: the first ( EB2 ) specifies the solid wire composition, while the second ( -B2 ) specifies the chemical composition of the deposited weld metal produced by that wire-flux combination. If an unalloyed wire ( EM12K ) is used with an alloy flux, the classification becomes F8A4-EM12K-B2 .
Exam Trap 3: Triple-Deoxidized ER70S-2 in Multi-Pass GMAW Spray Arc ER70S-2 contains Ti, Zr, and Al deoxidizers. While unmatched for single-pass GTAW root passes, using ER70S-2 in high-current, multi-pass spray-transfer GMAW causes non-metallic oxide inclusion accumulation (TiO2, Al2O3), lowering Charpy V-notch toughness compared to an ER70S-6 wire.