Study guide
6.1 DC and AC Waveforms, Polarity Thermodynamics & Welding Circuit Analysis
AWS CWEng Certified Welding Engineer Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & CWEng Exam Overview
About the CWEng Exam: Four Parts, 163 Questions & Testing Logistics Scoring, Composite Weighting, Eligibility & Five-Year Renewal How to Use This Guide & Build Your Open-Book Reference Set
2 Chapter 1: Mathematics & Statistics for Welding Engineers
1.1 Engineering Mathematics: Algebra, Trigonometry & Geometry in Weldments 1.2 Differential & Integral Calculus Fundamentals in Engineering Analysis 1.3 Applied Engineering Statistics, Population Distributions & Quality Metrics 1.4 Polynomial Equations, Conic Sections & Complex Numbers
3 Chapter 2: Physics Fundamentals & Mechanics
2.1 Unit Systems, Dimensional Analysis & Engineering Conversions 2.2 Mechanics: Statics, Equilibrium, Force Vectors & Moments 2.3 Work, Energy, Power & Mechanical Advantage in Welding Systems 2.4 Thermal Physics, Linear/Volumetric Expansion & Heat Capacity
4 Chapter 3: General & Physical Chemistry for Welding
3.1 Atomic Structure, Bonding & Solid-Solution Thermodynamics 3.2 Hume-Rothery Compatibility, Interstitial Strain & HSLA Microalloy Scavenging 3.3 Gas Laws, Dalton Partial Pressures, Arc Dissociation & Sieverts Law 3.4 Cylinder Capacity, Available Arc Time & Gas-Related Porosity Diagnosis 3.5 Redox Thermodynamics, Deoxidation & Slag-Metal Refining 3.6 Basicity Index Calculations, Toughness Prediction & Cryogenic Consumable Selection
5 Chapter 4: Strength of Materials & Mechanics of Materials
4.1 Engineering vs. True Stress-Strain, Elastic Constants & Z-Direction Ductility 4.2 Plane Stress vs. Plane Strain, Triaxial Restraint & Alloy Property Comparison 4.3 Beam Bending, Transverse Shear, Torsion & Mohr Circle Construction 4.4 Multiaxial Yield Criteria & Combined-Load Analysis of Welded Members 4.5 Fatigue Life, Weld-Toe Stress Concentration & Paris-Erdogan Crack Growth 4.6 LEFM Fracture Toughness, Ductile-Brittle Transition & Larson-Miller Creep 4.7 Comparative Failure-Mode Synthesis & Integrated Flaw and Creep Assessment
6 Chapter 5: Heat Transfer & Fluid Mechanics in Welding
5.1 Fourier Conduction, Rosenthal Moving Heat Source & 2D vs. 3D Heat Flow 5.2 Adams Cooling Rate, the t8/5 Window & HAZ Peak-Temperature Distribution 5.3 Convection, Stefan-Boltzmann Radiation & Emissivity of Weld Surfaces 5.4 Arc Radiation Losses, Preheat Maintenance & PWHT Boundary Conditions 5.5 Fluid Statics, Bernoulli, Viscosity & Reynolds-Number Regimes 5.6 Gas Lens Mechanics, Buoyancy Effects & Torch Flow Design 5.7 Hyperbaric, Vacuum & Controlled-Atmosphere Welding Environments
7 Chapter 6: Electrical Engineering Principles for Welding Systems
6.1 DC and AC Waveforms, Polarity Thermodynamics & Welding Circuit Analysis 6.2 Joule Heating, Electrode Stickout Preheating & Circuit Voltage Distribution 6.3 Power Factor, Reactance, Impedance & Magnetic Transformer Principles 6.4 Lorentz Force, Electromagnetic Pinch Effect & Arc Blow
8 Chapter 7: Welding Heat Sources & Arc Physics
7.1 Volt-Ampere Characteristics, Operating Point, Self-Regulation & OCV Limits 7.2 Inductance, Slope Control & Dynamic Power-Source Response 7.3 Arc Fall Regions, Cathode Emission Mechanisms & Shielding-Gas Ionization 7.4 Maecker Plasma Jet, Degree of Ionization & Anode Heat Partitioning 7.5 Droplet Force Balance & Classification of Metal Transfer Regimes 7.6 Transition Current, Mode Comparison & Pulsed Waveform Design
9 Chapter 8: Arc Welding Processes & Parameter Controls
8.1 Shielded Metal Arc Welding (SMAW): Electrode Flux Chemistries & Variables 8.2 GMAW Process Physics, Transfer Modes & Shielding Gas Interactions 8.3 Solid, Metal-Cored & Flux-Cored Wires with CTWD and Parameter Envelopes 8.4 Gas Tungsten (GTAW) & Plasma Arc Welding (PAW): Electrodes & Keyholing 8.5 Submerged Arc Welding (SAW): Flux Basicity, Multi-Wire & High-Deposition Systems
10 Chapter 9: Advanced, Resistance & Solid-State Joining Processes
9.1 High-Energy-Density Beam Physics & Electron Beam Welding 9.2 Laser Beam Welding, EBW/LBW Comparison & Fiber Laser Parameter Derivation 9.3 Resistance Welding Physics, Electrode Materials & Spot Weld Sequence 9.4 Nugget Sizing, Seam and Projection Welding, and Lobe Curve Process Windows 9.5 Solid-State Joining: Friction Stir Welding (FSW), Explosion & Diffusion 9.6 Thermal Cutting & Gouging: Oxyfuel, Plasma Arc and Air Carbon Arc 9.7 High-Frequency, Flash, Stud & Ultrasonic Welding; Surfacing and Thermal Spray
11 Chapter 10: Physical & Transformation Metallurgy of Steels
10.1 Fe-Fe3C System, Crystal Lattices, c/a Ratio & Interstitial Solubility 10.2 Critical Temperatures, Invariant Reactions & the Lever Rule 10.3 Alloying Elements, the Gamma Loop & Phase-Fraction Calculations 10.4 TTT and CCT Diagrams, Constitutional Supercooling & Scheil Microsegregation 10.5 Non-Equilibrium Transformation Products & Martensite Modeling 10.6 HAZ Anatomy, Microstructural Sub-Zones & Multi-Pass Reheated Regions 10.7 HAZ Hardness Traverses, Toughness Gradients & Peak-Temperature Control
12 Chapter 11: Weldability, Cracking Mechanisms & Alloy Metallurgy
11.1 Hydrogen Cracking Conditions, Carbon Equivalent & Diffusible Hydrogen Control 11.2 Preheat, Interpass and Post-Heat Calculations for Cold-Crack Prevention 11.3 Solidification Cracking, Bead Aspect Ratio, Liquation & Lamellar Tearing 11.4 Lamellar Tearing Mitigation & Hot-Cracking Susceptibility Evaluation 11.5 Stainless Families, Schaeffler and WRC-1992 Diagrams, Ferrite Number & Sensitization 11.6 Duplex Stainless Metallurgy & Dissimilar-Metal Ferrite Prediction 11.7 Aluminum Oxide and Porosity Control, and Titanium Reactive-Metal Welding 11.8 Nickel Superalloys, Strain-Age Cracking & Guinier-Preston Aging Sequences
13 Chapter 12: Weldment Design, Stress Analysis & Joint Mechanics
12.1 AWS A2.4 Welding Symbol Anatomy, Symbol Library & Dimension Syntax 12.2 Joint Architecture, CJP versus PJP, and NDE Examination Symbols 12.3 Fillet and Groove Weld Sizing under Direct Stress in ASD and LRFD 12.4 Plug and Slot Welds, Stress Gradients & the Fillet Weld Break Test 12.5 Eccentric Loading Analysis: Elastic Vector Method vs Instantaneous Center 12.6 Fatigue Design of Welded Connections & Residual Stress/Distortion Control
14 Chapter 13: Non-Destructive Examination (NDE) & Discontinuity Analysis
13.1 Visual Testing Gages & Liquid Penetrant Capillary Mechanics 13.2 Magnetic Particle Testing: Flux Leakage, Field Geometry & Prod Amperage 13.3 Radiographic Physics, Geometric Unsharpness, Density & IQI Sensitivity 13.4 Computed and Digital Radiography & Radiographic Discontinuity Interpretation 13.5 Acoustic Wave Mechanics, Refraction & Angle-Beam Sound-Path Geometry 13.6 AWS D1.1 Decibel Rating, Phased Array & Time-of-Flight Diffraction
15 Chapter 14: Brazing, Soldering & Industrial Welding Safety
14.1 Brazing Thermodynamics, Capillary Wetting Physics & Joint Clearance 14.2 AWS A5.8 Brazing Filler Metals, FB Fluxes & Industrial Heating Processes 14.3 Soldering Fundamentals, Flux Chemistries & Intermetallic Formation 14.4 Hierarchy of Controls, Electric Shock Physics & Industrial Ventilation 14.5 Fume Exposure Limits, Arc Radiation, Hot Work and Confined-Space Entry 14.6 Arc-Generated Toxic Gases, Moving-Equipment Hazards & TWA Exposure Calculation
16 Chapter 15: Structural Fabrication & AWS D1.1 Code Implementation
15.1 AWS D1.1 Scope, Prequalification Limits, Base-Metal Groups & Matching Filler 15.2 Prequalified Joint Details, Backing Systems & Joint Specification Verification 15.3 Thermal Cut Edges, Fit-Up Tolerances & Minimum Preheat Requirements 15.4 Preheat Application Zones, Measurement Instrumentation & Fabrication Audits 15.5 PWHT Fundamentals, D1.1 Thermal Cycles & Visual Acceptance Criteria 15.6 D1.1 Nondestructive Examination Protocols, PWHT Scheduling & Visual Audit Practice
17 Chapter 16: Welding Procedure Qualification (WPS & PQR) per ASME IX & AWS B2.1
16.1 PQR versus WPS Hierarchy, Qualification Workflow & Standard Procedures 16.2 Manufacturer Responsibility, Subcontracting Limits & Multi-Process Qualification 16.3 Essential, Supplementary Essential and Nonessential Variables with Heat Input Mechanics 16.4 Waveform-Controlled Power Sources, Appendix H & Heat-Input Compliance 16.5 P-Numbers, Group Numbers, F-Numbers & A-Numbers 16.6 QW-451 Mechanical Test Protocols & Procedure Qualification Test Evaluation
18 Chapter 17: Filler Metal Specifications, Selection & Consumable Control
17.1 AWS A5 Architecture: SMAW, GMAW/GTAW and FCAW Consumable Classifications 17.2 SAW Wire-Flux Systems, Alloy Pickup & PWHT Property Effects 17.3 Stainless Filler Specifications, Solidification Modes & Dissimilar-Metal Joints 17.4 AWS A5.10 Aluminum Filler Selection & Dilution and Ferrite-Number Calculations 17.5 Consumable Storage, Conditioning Envelopes & Atmospheric Exposure Limits 17.6 Low-Hydrogen Designators, the Yurioka Parameter & Preheat Sizing
19 Chapter 18: Welder Performance Qualification, Quality Management & Welding Economics
18.1 Welder Qualification Philosophy, Test Positions & Thickness and Diameter Ranges 18.2 F-Number Hierarchy, Operator Qualification & Continuity Requirements 18.3 ISO 3834, Welding Coordination, Inspection Test Plans & Equipment Validation 18.4 EN 10204 Material Certification, Traceability & Heat-Input Nonconformance Auditing 18.5 Weld Cost Anatomy, Deposition Rates, Operating Factor & the Overwelding Law 18.6 Economic Optimization Strategies & Fabrication Cost Comparison
6.1 DC and AC Waveforms, Polarity Thermodynamics & Welding Circuit Analysis
Key Takeaways Explain This Topic AI
Polarity dictates thermal energy distribution across the arc: in non-consumable GTAW, DCEN concentrates ~70% of heat into the workpiece anode and ~30% into the tungsten cathode, whereas DCEP reverses this ratio, requiring severe electrode current derating.
In consumable electrode processes (GMAW, SMAW), DCEP is standard because cathode spot emission on the base metal cleans surface oxides and provides deep penetration, whereas DCEN increases wire melting rate by 30-50% due to cathode fall heating of the wire tip at the expense of penetration.
A complete welding circuit represents a distributed series resistance network governed by Kirchhoff's Voltage Law (KVL), where parasitic voltage drops across welding cables, contact tip interfaces, and ground connections directly subtract from the voltage available at the arc.
Joule's First Law (Q = I^2 * R * t) governs both destructive parasitic heating in undersized welding cables and functional preheating in the electrode extension (wire stickout), which exponentially accelerates GMAW and SAW wire melting rates.
The welding arc column does not obey linear Ohm's Law (V = IR); it functions as an ionized plasma with non-linear volt-ampere characteristics and negative incremental resistance (dV/dI < 0) at low-to-medium current levels.
Last updated: September 2026
6.1 DC & AC Circuit Fundamentals, Ohm's Law & Kirchhoff's Laws
Quick Answer: Direct Current (DC) delivers continuous, unidirectional electron drift, whereas Alternating Current (AC) cyclically reverses polarity through zero-current transitions. In welding circuits, polarity dictates thermal distribution: Direct Current Electrode Negative (DCEN) concentrates approximately 70% of arc heat into the workpiece anode in Gas Tungsten Arc Welding (GTAW), whereas Direct Current Electrode Positive (DCEP) yields superior cleaning action and deep penetration in Gas Metal Arc Welding (GMAW). Total loop performance is governed by Kirchhoff's Voltage Law ( ∑ V = 0 \sum V = 0 ∑ V = 0 ), where parasitic cable and contact-tip resistance subtract from open-circuit potential, and Joule heating ( P = I 2 R P = I^2 R P = I 2 R ) in the electrode stickout provides functional preheating that dramatically boosts consumable deposition rates.
1. DC vs AC Waveforms in Arc Welding Systems
Every electric arc welding system relies on an energized closed circuit that converts electrical potential energy into localized thermal energy within an ionized gas column (plasma). The nature of the current waveform—Direct Current (DC) or Alternating Current (AC)—governs arc stability, heat partitioning, and surface oxide disruption. Direct Current (DC) Alternating Current (AC)
- Current (I) Current (I)
- ^
- +I |----------------------- +I | _--_ _--_
- | | / / / /
- 0 +------------------------> Time 0 +----+------+----+------+--> Time
- | | / / / /
- I | -I | -- --
- Direct Current (DC) Characteristics
Unidirectional Flow: Electrons drift steadily from the negative terminal (cathode) toward the positive terminal (anode) with drift velocity v d = I / ( n e A ) v_d = I / (n e A) v d = I / ( n e A ) , where n n n is charge carrier density, e e e is elementary charge, and A A A is conductor cross-section.
Continuous Plasma Ionization: Because current never crosses zero, the thermal ionization of the shielding gas remains continuous, eliminating cyclic arc extinguishing and re-ignition transients.
Polarity Invariance: Cathode and anode spots remain stationary on their respective conductors, establishing steady thermal and metallurgical gradients.
Alternating Current (AC) Characteristics
Cyclic Reversal: Current alternates sinusoidally (or via modern inverter squarewaves) at power-line frequencies ( 50 Hz 50\text{ Hz} 50 Hz or 60 Hz 60\text{ Hz} 60 Hz ) or inverter-controlled frequencies ( 20 to 400 Hz 20\text{ to }400\text{ Hz} 20 to 400 Hz ).
Zero-Crossing Extinction: Twice per cycle, current drops to zero ( I = 0 I = 0 I = 0 ). As current approaches zero, plasma temperature falls, deionizing the arc path. Re-igniting the arc on the subsequent half-cycle requires either a high open-circuit voltage (OCV), capacitive pulse injection, or continuous high-frequency (HF) spark stabilization ( 1 to 2 MHz 1\text{ to }2\text{ MHz} 1 to 2 MHz ).
Cathodic Etching (Cleaning Action): When the electrode is positive (DCEP half-cycle), heavy positive shielding gas ions ( Ar + , He + \text{Ar}^+, \text{He}^+ Ar + , He + ) are accelerated toward the workpiece cathode by the cathode fall potential. These massive ions blast refractory surface oxide films (e.g., Al 2 O 3 \text{Al}_2\text{O}_3 Al 2 O 3 with melting point 2072 ∘ C 2072^\circ\text{C} 207 2 ∘ C on aluminum base metal melting at 660 ∘ C 660^\circ\text{C} 66 0 ∘ C , or MgO \text{MgO} MgO on magnesium) via cathodic sputtering. During the subsequent electrode negative (DCEN half-cycle), electrons flow into the workpiece, generating deep penetration.
2. Polarity Dynamics: DCEP vs DCEN Thermodynamics
In electric arc welding, polarity designates the electrical connection of the welding torch electrode relative to the workpiece. DCEN (Straight Polarity) DCEP (Reverse Polarity)
- (-) Electrode (+) Workpiece (+) Electrode (-) Workpiece
- [Cathode] [Anode] [Anode] [Cathode]
- | | | |
- | e- (Electrons) | | Positive Ions |
- +-------->--------->+ +<-------+--------+
- | | | | |
- +<--------+---------+ +-------->------->+
- Positive Ions e- (Electrons)
- ~70% Heat at Workpiece (GTAW) ~70% Heat at Electrode (GTAW)
- Arc Zone Physics & Energy Partitioning
The total voltage drop across a welding arc consists of three contiguous zones: V arc = V c + V p + V a V_{\text{arc}} = V_c + V_p + V_a V arc = V c + V p + V a
where V c V_c V c is the cathode fall voltage ( 2 to 5 V 2\text{ to }5\text{ V} 2 to 5 V ), V p V_p V p is the positive plasma column voltage ( 10 to 25 V 10\text{ to }25\text{ V} 10 to 25 V , proportional to arc length), and V a V_a V a is the anode fall voltage ( 1 to 4 V 1\text{ to }4\text{ V} 1 to 4 V ).
Heat Input at the Anode ( Q a Q_a Q a ): Electrons arriving at the anode accelerate through the anode fall V a V_a V a , impacting the anode surface and releasing their kinetic energy plus the electronic condensation energy (the material work function Φ a \Phi_a Φ a , typically 4.0 to 4.5 eV 4.0\text{ to }4.5\text{ eV} 4.0 to 4.5 eV for steel): Q a = I ( V a + Φ a + 3 2 k B T e e ) Q_a = I \left( V_a + \Phi_a + \frac{3}{2} \frac{k_B T_e}{e} \right) Q a = I ( V a + Φ a + 2 3 e k B T e )
where 3 2 k B T e e \frac{3}{2} \frac{k_B T_e}{e} 2 3 e k B T e represents the thermal kinetic energy of the electron gas.
Heat Input at the Cathode ( Q c Q_c Q c ): The cathode receives kinetic and neutralization energy from impacting positive gas ions, but simultaneously loses thermal energy due to thermionic electron cooling (the cooling effect of electrons overcoming the cathode work function Φ c \Phi_c Φ c ): Q c = I i ( V c + V i − Φ c ) − I e Φ c Q_c = I_i (V_c + V_i - \Phi_c) - I_e \Phi_c Q c = I i ( V c + V i − Φ c ) − I e Φ c
where V i V_i V i is the gas ionization potential, I i I_i I i is ion current, and I e I_e I e is electron current ( I = I i + I e I = I_i + I_e I = I i + I e ).
Industrial Comparison: Non-Consumable vs Consumable Processes
Process Polarity Electrode Heating Workpiece Heating Penetration Profile Primary Industrial Application
GTAW DCEN (Straight) ~30% ~70% Deep, narrow penetration Carbon/stainless steels, titanium, nickel alloys. Sharp tungsten tip maintained.
GTAW DCEP (Reverse) ~70% ~30% Extremely shallow, wide Heavy tungsten balling/melting. Current derated by 90%. Rarely used alone.
GTAW AC (Balanced) ~50% ~50% Medium penetration Aluminum and magnesium alloys. DCEP provides cleaning; DCEN provides penetration.
GMAW DCEP (Reverse) ~30% ~70% (effective) Deep, finger-like penetration Standard GMAW for all structural steels and alloys. High cathode spot mobility on base metal yields stable arc and axial spray transfer.
GMAW DCEN (Straight) ~70% ~30% Shallow penetration, high reinforcement Cladding, hardfacing, sheet metal. Wire melt-off rate increases by 30-50%, but cathode spot wandering creates repulsive globular spatter unless special flux/gas is used.
SMAW DCEP (EXX18) Moderate High Deep, ductile penetration Out-of-position structural welding, high-toughness pressure retaining piping.
SMAW DCEN (EXX12) High Moderate Shallow penetration Sheet metal fabrication, poor fit-up joints, fast-fill root runs.
CWEng Distinction: In GTAW (non-consumable tungsten), DCEN gives the deepest penetration because the workpiece is the anode absorbing electron condensation energy. In GMAW (consumable wire), DCEP is standard and gives the deepest penetration into the base metal because cathode spots on the base plate aggressively etch oxides and allow the concentrated plasma jet to dig into the weld pool, while DCEN causes cathode spots to wander erratically across the liquid wire droplet, producing upward repulsive forces and shallow penetration.
3. Circuit Analysis: Ohm's Law, Kirchhoff's Laws & Distributed Loop Resistance
A welding power supply does not deliver its terminal voltage directly to the arc. The welding circuit is a distributed network of series and parallel resistances governed by classical circuit laws. +---[ R_cable (Electrode Lead) ]---+---[ R_contact-tip ]---+
- | |
- (+) | v
- [ POWER SOURCE ] [ R_stickout ]
- (V_source) |
- | v
- (-) | [ V_arc ]
- | |
- +---[ R_cable (Ground Lead) ]------+---[ R_ground-clamp ]--+---[ Base Metal ]
- Linear Ohm's Law vs Non-Linear Arc Conduction
For linear passive metallic conductors (copper cables, brass contact tips, steel plate): V = I ⋅ R = I ( ρ L A ) V = I \cdot R = I \left( \frac{\rho L}{A} \right) V = I ⋅ R = I ( A ρ L )
where ρ \rho ρ is electrical resistivity ( Ω ⋅ m \Omega\cdot\text{m} Ω ⋅ m ), L L L is conductor length ( m \text{m} m ), and A A A is cross-sectional area ( m 2 \text{m}^2 m 2 ).
In stark contrast, the welding arc column is a non-linear plasma conductor . It does NOT obey Ohm's Law. At low currents, an increase in current causes increased thermal ionization, raising electrical conductivity faster than current rises, resulting in a negative incremental resistance : d V arc d I < 0 \frac{dV_{\text{arc}}}{dI} < 0 d I d V arc < 0
At high currents (typical of GMAW spray and submerged arc welding), the plasma column approaches full ionization and thermal expansion limits, causing the arc characteristic to flatten and transition to slightly positive incremental resistance.
Kirchhoff's Laws Applied to the Welding Loop
Kirchhoff's Current Law (KCL: ∑ I in = ∑ I out \sum I_{\text{in}} = \sum I_{\text{out}} ∑ I in = ∑ I out ): In a single-torch system, the total current leaving the power source electrode terminal passes through the cable, contact tip, wire extension, arc plasma, workpiece, ground clamp, and return cable in strict series: I source = I cable = I tip = I stickout = I arc = I ground I_{\text{source}} = I_{\text{cable}} = I_{\text{tip}} = I_{\text{stickout}} = I_{\text{arc}} = I_{\text{ground}} I source = I cable = I tip = I stickout = I arc = I ground
In multi-head tandem systems (e.g., multi-wire SAW) sharing a common workpiece, KCL dictates that the total return ground current equals the vector/scalar sum of all individual torch currents: I total ground = ∑ k = 1 n I k I_{\text{total ground}} = \sum_{k=1}^n I_k I total ground = k = 1 ∑ n I k
Kirchhoff's Voltage Law (KVL: ∑ V k = 0 \sum V_k = 0 ∑ V k = 0 ): Tracing the closed loop from the power source positive terminal to the negative terminal: V source − V lead-cable − V contact-tip − V stickout − V arc − V work − V ground-clamp − V return-cable = 0 V_{\text{source}} - V_{\text{lead-cable}} - V_{\text{contact-tip}} - V_{\text{stickout}} - V_{\text{arc}} - V_{\text{work}} - V_{\text{ground-clamp}} - V_{\text{return-cable}} = 0 V source − V lead-cable − V contact-tip − V stickout − V arc − V work − V ground-clamp − V return-cable = 0
Solving for the actual voltage available to sustain the welding arc: V arc = V source − I ( R cables + R tip + R stickout + R clamp ) V_{\text{arc}} = V_{\text{source}} - I \left( R_{\text{cables}} + R_{\text{tip}} + R_{\text{stickout}} + R_{\text{clamp}} \right) V arc = V source − I ( R cables + R tip + R stickout + R clamp )