Study guide

3.5 Geometric Discontinuities: Undercut, Overlap, and Profile

AWS CWI Certified Welding Inspector Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction to the AWS CWI Certification

What Is the AWS CWI Certification? CWI Exam Structure: Parts A, B, and C Eligibility Requirements and Application

2 1. Welding Processes and Fundamentals

1.1 SMAW — Shielded Metal Arc Welding (Stick) 1.2 GMAW — Gas Metal Arc Welding (MIG/MAG) 1.3 FCAW — Flux-Cored Arc Welding 1.4 GTAW — Gas Tungsten Arc Welding (TIG) 1.5 SAW — Submerged Arc Welding 1.6 Other Welding, Cutting Processes, and Process Variables

3 2. Welding Metallurgy and Heat Control

2.1 The Iron-Carbon Phase Diagram 2.2 The Heat-Affected Zone (HAZ) 2.3 Preheat and Interpass Temperature 2.4 Hydrogen-Induced Cracking (HIC) 2.5 Distortion and Residual Stress

4 3. Weld Discontinuities and Defects

3.1 Discontinuity vs. Defect — Definitions and Concepts 3.2 Cracks — Types, Causes, and Significance 3.3 Porosity and Inclusions 3.4 Incomplete Fusion and Incomplete Joint Penetration 3.5 Geometric Discontinuities: Undercut, Overlap, and Profile

5 4. Nondestructive Examination (NDE) Methods

4.1 Visual Testing (VT) 4.2 Liquid Penetrant Testing (PT) 4.3 Magnetic Particle Testing (MT) 4.4 Radiographic Testing (RT) and Ultrasonic Testing (UT)

6 5. Welding Symbols and Terminology

5.1 Anatomy of a Welding Symbol (AWS A2.4) 5.2 Joint Types, Weld Types, and Welding Positions 5.3 Essential Welding Definitions and Terminology

7 6. WPS, PQR, and Welder Qualification

6.1 Welding Procedure Specification (WPS) 6.2 Procedure Qualification Record (PQR) 6.3 Welder Performance Qualification (WPQ)

8 7. Destructive Testing Methods

7.1 Tensile Testing 7.2 Guided Bend, Nick Break, and Fillet Weld Break Tests 7.3 Impact Testing and Hardness Testing

9 8. Welding Safety and Inspector Duties

8.1 Welding Safety Hazards and Prevention 8.2 CWI Duties and Responsibilities 8.3 Welding-Related Calculations

10 9. AWS D1.1 Code Application (Part C)

9.1 AWS D1.1:2025 Code Structure and Navigation 9.2 Clause 5 — Prequalification Requirements 9.3 Clause 8 — Inspection and Acceptance Criteria 9.4 Part B Practical Exam Preparation

11 10. Exam Strategies and Comprehensive Review

10.1 Part A (Fundamentals) Exam Strategies 10.2 Part C (Code Application) Exam Strategies 10.3 Comprehensive Review — 25 Practice Questions

3.5 Geometric Discontinuities: Undercut, Overlap, and Profile

Key Takeaways Explain This Topic AI

Undercut limits (AWS D1.1): 0.010 in. for cyclically loaded, ~1/32 in. for statically loaded members

Overlap is surface lack of fusion — a stress-concentrating notch, generally not acceptable

Groove-weld reinforcement limits: 1/8 in. for material up to 1 in. thick, 3/16 in. over 1 in.

Arc strikes must be ground smooth and visually inspected for cracks; spatter must be removed

  • Theoretical fillet throat = 0.707 × leg size; most geometric discontinuities are found by VT
  • Last updated: June 2026

Surface and Profile Discontinuities

Geometric discontinuities are conditions of the weld's shape and surface — they change the cross-section or surface profile and act as notches. Most are surface-breaking, so visual testing (VT) is the primary detection method, making them the bread-and-butter of CWI Part B (Practical) gauge work. They are generally less severe than cracks or lack of fusion, but several are routinely rejectable, and undercut and overlap are among the most frequently tested topics on the whole exam.

Undercut

Per AWS A3.0, undercut is "a groove melted into the base metal adjacent to the weld toe or weld root and left unfilled by weld metal." It removes load-carrying section and leaves a sharp notch that initiates fatigue cracks — especially dangerous in cyclically loaded structures.

Toe undercut — at the weld face/base-metal junction.

Root undercut — on the root side of the joint.

Causes: excessive current (amperage too high), excessive arc length/voltage, travel speed too fast, improper electrode (work) angle, and excessive weave that overheats the toe.

AWS D1.1 acceptance (visual):

  • Loading Undercut limit
  • Cyclically loaded, member transverse to tensile stress ≤ 0.010 in. (0.25 mm) deep

Statically loaded ≤ 1/32 in. (1 mm) for any length, OR ≤ 1/16 in. (1.6 mm) for cumulative lengths up to a code-specified amount

The tighter cyclic limit exists because fatigue cracks readily nucleate from the undercut notch.

Overlap (Cold Lap)

Per AWS A3.0, overlap is "the protrusion of weld metal beyond the weld toe or weld root" — weld metal that has rolled over onto the base-metal surface without fusing to it. It is essentially surface lack of fusion and creates a sharp re-entrant notch at the toe. Overlap is generally not acceptable because it both forms a stress-concentrating notch and signals probable lack of fusion underneath. Causes: travel speed too slow, amperage too low (the puddle runs ahead of the arc), improper electrode angle, and oversized electrode for the joint.

Reinforcement, Underfill, and Convexity

Weld reinforcement is weld metal in excess of that required to fill the joint. Some face reinforcement is normal; excessive reinforcement creates an abrupt toe transition (stress concentration) and wastes filler. AWS D1.1 limits groove-weld face reinforcement to 1/8 in. (3 mm) for material up to 1 in. thick and 3/16 in. (5 mm) for thicker material; the weld must also blend smoothly to the base metal.

Underfill is the opposite — a groove-weld face (or root) below the base-metal surface, leaving the joint under-thickness and rejectable. Excessive convexity (fillet face too bulged) creates a sharp toe; excessive concavity reduces the effective throat and undersizes the weld.

Fillet-Weld Throat and Size

For an equal-leg fillet weld , the theoretical throat = 0.707 × leg size (cos 45° = 1/√2 ≈ 0.707). A 1/2-in. fillet therefore has a 0.354-in. theoretical throat. Undersized legs or a throat below the specified minimum (often from excessive concavity) make the weld rejectable.

Mismatch (High-Low), Arc Strikes, Spatter, and More

Discontinuity Description Significance / treatment

Mismatch / high-low Misalignment of the two members' surfaces at a butt joint Creates a stress concentration and eccentric load path; limited by code (e.g., D1.1 caps offset of abutting parts)

Arc strike Localized remelted/heat-affected spot from striking the arc outside the joint Leaves a hard, brittle (martensitic) HAZ and possible micro-cracks; D1.1 requires it be ground smooth and VT'd for cracks , especially on cyclically loaded members

Spatter Metal droplets thrown onto the surface Usually a workmanship/cosmetic issue; must be removed because it can mask other discontinuities and start corrosion

  • Excessive convexity Bulged fillet face Sharp toe — stress riser
  • Excessive concavity / insufficient throat Sunken fillet face Throat below minimum = undersized weld

Melt-through / excessive root reinforcement Excess root-side metal Limited by code; abrupt root profile concentrates stress

Discontinuity → Cause → Detection Quick Reference

  • Discontinuity Typical cause Primary detection
  • Undercut High current, fast travel, long arc, bad angle VT (and undercut gauge)
  • Overlap Slow travel, low amperage, bad angle VT
  • Excessive reinforcement / convexity Too much fill, low travel speed VT (fillet/weld gauge)
  • Underfill / insufficient throat Too little fill, excessive concavity VT (gauge)
  • Mismatch (high-low) Poor fit-up/alignment VT (Hi-Lo gauge)
  • Arc strike Striking arc off the joint VT , then MT/PT for cracks
  • Porosity (surface) Gas/moisture/wind VT ; subsurface by RT
  • Slag inclusion Poor interpass cleaning RT / UT
  • Incomplete fusion / penetration Low heat, bad angle, joint geometry UT (RT for IJP)
  • Cracks Hydrogen, restraint, S/P films VT/MT/PT (surface), UT (subsurface)

Exam essentials: Memorize the D1.1 undercut numbers — 0.010 in. cyclic, 1/32 in. static — and reinforcement limits 1/8 in. (≤1 in. thick), 3/16 in. (>1 in.) . Overlap is generally not acceptable (surface lack of fusion). Arc strikes must be ground and re-inspected for cracking. Fillet throat = 0.707 × leg.