Study guide
8.2 CWI Duties and Responsibilities
AWS CWI Certified Welding Inspector Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction to the AWS CWI Certification
What Is the AWS CWI Certification? CWI Exam Structure: Parts A, B, and C Eligibility Requirements and Application
2 1. Welding Processes and Fundamentals
1.1 SMAW — Shielded Metal Arc Welding (Stick) 1.2 GMAW — Gas Metal Arc Welding (MIG/MAG) 1.3 FCAW — Flux-Cored Arc Welding 1.4 GTAW — Gas Tungsten Arc Welding (TIG) 1.5 SAW — Submerged Arc Welding 1.6 Other Welding, Cutting Processes, and Process Variables
3 2. Welding Metallurgy and Heat Control
2.1 The Iron-Carbon Phase Diagram 2.2 The Heat-Affected Zone (HAZ) 2.3 Preheat and Interpass Temperature 2.4 Hydrogen-Induced Cracking (HIC) 2.5 Distortion and Residual Stress
4 3. Weld Discontinuities and Defects
3.1 Discontinuity vs. Defect — Definitions and Concepts 3.2 Cracks — Types, Causes, and Significance 3.3 Porosity and Inclusions 3.4 Incomplete Fusion and Incomplete Joint Penetration 3.5 Geometric Discontinuities: Undercut, Overlap, and Profile
5 4. Nondestructive Examination (NDE) Methods
4.1 Visual Testing (VT) 4.2 Liquid Penetrant Testing (PT) 4.3 Magnetic Particle Testing (MT) 4.4 Radiographic Testing (RT) and Ultrasonic Testing (UT)
6 5. Welding Symbols and Terminology
5.1 Anatomy of a Welding Symbol (AWS A2.4) 5.2 Joint Types, Weld Types, and Welding Positions 5.3 Essential Welding Definitions and Terminology
7 6. WPS, PQR, and Welder Qualification
6.1 Welding Procedure Specification (WPS) 6.2 Procedure Qualification Record (PQR) 6.3 Welder Performance Qualification (WPQ)
8 7. Destructive Testing Methods
7.1 Tensile Testing 7.2 Guided Bend, Nick Break, and Fillet Weld Break Tests 7.3 Impact Testing and Hardness Testing
9 8. Welding Safety and Inspector Duties
8.1 Welding Safety Hazards and Prevention 8.2 CWI Duties and Responsibilities 8.3 Welding-Related Calculations
10 9. AWS D1.1 Code Application (Part C)
9.1 AWS D1.1:2025 Code Structure and Navigation 9.2 Clause 5 — Prequalification Requirements 9.3 Clause 8 — Inspection and Acceptance Criteria 9.4 Part B Practical Exam Preparation
11 10. Exam Strategies and Comprehensive Review
10.1 Part A (Fundamentals) Exam Strategies 10.2 Part C (Code Application) Exam Strategies 10.3 Comprehensive Review — 25 Practice Questions
8.2 CWI Duties and Responsibilities
Key Takeaways Explain This Topic AI
CWI duties fall into three phases: before (verification), during (in-process monitoring), and after welding (inspection/documentation)
The CWI verifies the WPS and welder qualifications but does not write the WPS or perform welding — those are engineering/production roles
In-process duties include monitoring parameters, interpass temperature (min and max), cleaning, technique, and consumables
AWS QC1 ethics demand impartiality; falsifying inspection records is the gravest violation and can void certification
AWS B5.1 defines Level I (CAWI, supervised), Level II (CWI, independent accept/reject), and Level III (SCWI, supervisory)
Last updated: June 2026
The Three Phases of Inspection
The CWI's duties span the entire welding lifecycle, and the exam expects you to place each duty in the correct phase — before , during , or after welding. The single biggest conceptual point tested is that the CWI verifies and inspects; the CWI does not perform engineering or production work . The inspector does not write the Welding Procedure Specification (WPS), does not set the production schedule, and does not weld — the inspector confirms that qualified people and documents are in place and that the code is met.
Phase 1 — Before Welding (Pre-Weld Verification)
Pre-weld inspection prevents defects before they happen and is the most cost-effective phase. The CWI verifies:
- Duty What to confirm
- Drawings & specs Joint design, weld size, NDE/acceptance criteria are understood
- WPS available & applicable A qualified WPS exists for each joint, position, and material
- Welder qualifications Each welder holds current, valid qualification for the process/position/material
- Base material Correct grade/spec, proper marking, no excessive rust, oil, scale, or moisture
- Consumables Electrode/wire matches the WPS; low-hydrogen electrodes properly stored/baked
- Joint fit-up Root opening, bevel angle, root face, alignment (high-low), backing, tack quality
- Preheat Minimum preheat met at the correct location and distance from the joint
- Equipment & environment Power source, gas flow, wind exposure (gas-shielded), temperature, moisture
A classic exam item asks which task is not the CWI's job before welding; the answer is usually "design/develop the WPS," which belongs to the welding engineer or qualified responsible party. The CWI reviews and verifies it.
Phase 2 — During Welding (In-Process Inspection)
In-process inspection catches problems that visual inspection of the finished weld cannot. Key duties:
Monitor welding parameters — amperage, voltage, and travel speed within WPS ranges (these control heat input)
Verify interpass temperature — both the minimum (often equal to preheat) and the maximum interpass limit, which protects the heat-affected zone (HAZ) and mechanical properties
- Check interpass cleaning — slag fully removed between passes; no trapped porosity
- Observe technique — electrode angle, stringer vs. weave per the WPS, correct bead sequence
- Confirm consumable usage — correct electrode/wire for root vs. fill/cap; correct shielding gas type and flow
Watch the environment — wind picking up on gas-shielded processes, preheat being maintained throughout (not just at the start)
Failing to maintain preheat or exceeding maximum interpass temperature are common real-world findings — the CWI must catch them while the weld is still in progress.
Phase 3 — After Welding (Post-Weld Inspection)
Once welding is complete, the CWI performs and coordinates final inspection:
- Duty Detail
- Visual inspection (VT) Evaluate profile, size, and surface discontinuities against acceptance criteria
- Measure weld size Fillet leg and throat; groove reinforcement height; with proper gauges
- Surface discontinuities Cracks, undercut, overlap, porosity, incomplete fusion at the surface
- Coordinate NDE Schedule/verify RT, UT, MT, PT per the governing code
- Review NDE results Evaluate technician reports; render accept/reject
- Verify PWHT If required, confirm temperature, hold time, and cooling-rate compliance
- Documentation & sign-off Record results, accept/reject decisions, and repair directives in writing
Visual inspection (VT) is the most-used and most cost-effective NDE method, and it is the CWI's primary direct tool.
Ethics and the Documentation Trail
Under AWS QC1 and the AWS Code of Ethics , the CWI must be impartial and objective , basing every accept/reject decision on the code — not on schedule pressure, relationships, or who signs the paycheck. The CWI must never falsify records, must work only within their area of competence, must protect proprietary information, and must report safety hazards and code violations. Falsifying an inspection report is the most serious ethical violation and can void the certification.
Records the CWI typically maintains include inspection reports, NDE reports, the WPS/PQR set, welder qualification records, material test reports (MTRs), and nonconformance/repair documentation.
When a weld is rejected, the CWI documents the discontinuity type, location, and the acceptance criterion it failed, then issues a written repair directive and re-inspects after repair . The inspector's reports become the legal quality record for the project; clear, factual, dated entries protect both the public and the inspector. The CWI's authority comes from the contract and the governing code — the inspector enforces the code but does not change it, and any deviation requires an engineering disposition (use-as-is, repair, rework, or reject) from the responsible engineer, not from the inspector alone.
AWS B5.1 — Three Levels of Welding Inspector
AWS B5.1, "Specification for the Qualification of Welding Inspectors," defines what each level may do:
Level Title Authority
Level I Associate Welding Inspector (CAWI) Inspects under the direct supervision of a CWI; does not make final accept/reject decisions
Level II Certified Welding Inspector (CWI) Inspects independently; makes accept/reject decisions; may supervise Level I
Level III Senior Certified Welding Inspector (SCWI) All Level II authority, plus develops procedures, trains, and resolves complex issues
For the Exam: Sort duties into before/during/after, remember the CWI verifies the WPS rather than writing it, and that only Level II (CWI) and Level III (SCWI) make independent accept/reject decisions. Objectivity per AWS QC1 is non-negotiable.