Study guide
5.1 Anatomy of a Welding Symbol (AWS A2.4)
AWS CWI Certified Welding Inspector Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction to the AWS CWI Certification
What Is the AWS CWI Certification? CWI Exam Structure: Parts A, B, and C Eligibility Requirements and Application
2 1. Welding Processes and Fundamentals
1.1 SMAW — Shielded Metal Arc Welding (Stick) 1.2 GMAW — Gas Metal Arc Welding (MIG/MAG) 1.3 FCAW — Flux-Cored Arc Welding 1.4 GTAW — Gas Tungsten Arc Welding (TIG) 1.5 SAW — Submerged Arc Welding 1.6 Other Welding, Cutting Processes, and Process Variables
3 2. Welding Metallurgy and Heat Control
2.1 The Iron-Carbon Phase Diagram 2.2 The Heat-Affected Zone (HAZ) 2.3 Preheat and Interpass Temperature 2.4 Hydrogen-Induced Cracking (HIC) 2.5 Distortion and Residual Stress
4 3. Weld Discontinuities and Defects
3.1 Discontinuity vs. Defect — Definitions and Concepts 3.2 Cracks — Types, Causes, and Significance 3.3 Porosity and Inclusions 3.4 Incomplete Fusion and Incomplete Joint Penetration 3.5 Geometric Discontinuities: Undercut, Overlap, and Profile
5 4. Nondestructive Examination (NDE) Methods
4.1 Visual Testing (VT) 4.2 Liquid Penetrant Testing (PT) 4.3 Magnetic Particle Testing (MT) 4.4 Radiographic Testing (RT) and Ultrasonic Testing (UT)
6 5. Welding Symbols and Terminology
5.1 Anatomy of a Welding Symbol (AWS A2.4) 5.2 Joint Types, Weld Types, and Welding Positions 5.3 Essential Welding Definitions and Terminology
7 6. WPS, PQR, and Welder Qualification
6.1 Welding Procedure Specification (WPS) 6.2 Procedure Qualification Record (PQR) 6.3 Welder Performance Qualification (WPQ)
8 7. Destructive Testing Methods
7.1 Tensile Testing 7.2 Guided Bend, Nick Break, and Fillet Weld Break Tests 7.3 Impact Testing and Hardness Testing
9 8. Welding Safety and Inspector Duties
8.1 Welding Safety Hazards and Prevention 8.2 CWI Duties and Responsibilities 8.3 Welding-Related Calculations
10 9. AWS D1.1 Code Application (Part C)
9.1 AWS D1.1:2025 Code Structure and Navigation 9.2 Clause 5 — Prequalification Requirements 9.3 Clause 8 — Inspection and Acceptance Criteria 9.4 Part B Practical Exam Preparation
11 10. Exam Strategies and Comprehensive Review
10.1 Part A (Fundamentals) Exam Strategies 10.2 Part C (Code Application) Exam Strategies 10.3 Comprehensive Review — 25 Practice Questions
5.1 Anatomy of a Welding Symbol (AWS A2.4)
Key Takeaways Explain This Topic AI
AWS A2.4 governs welding symbols; a complete symbol is built from the reference line, arrow, weld symbol, tail, dimensions, and supplementary symbols
Arrow-side/other-side is the most-tested convention: weld symbol BELOW the reference line = arrow side; ABOVE = other side; both = both sides
The reference line is ALWAYS drawn horizontal regardless of the joint's orientation on the drawing
Weld size goes to the LEFT of the symbol; length (and length-pitch for intermittent welds) goes to the RIGHT
Field weld = flag at the arrow/reference-line junction; weld-all-around = circle at that junction; finish letters are G (grind), M (machine), C (chip)
Groove weld size in parentheses to the left = effective throat/depth; root opening sits inside the symbol and the included groove angle is shown on the symbol
Last updated: June 2026
The Welding Symbol as a Language
Welding symbols are the standardized graphical shorthand defined by AWS A2.4 — Standard Symbols for Welding, Brazing, and Nondestructive Examination . They let an engineer specify exactly what weld goes where, how big, how long, on which side, by which process, and to what finish — all in a compact mark on a drawing. A Certified Welding Inspector (CWI) must read these symbols fluently because the welding symbol on the drawing is part of the contract documents ; the weld actually deposited must match what the symbol calls out. A misread symbol can mean a weld on the wrong side of a joint, an undersized fillet, or a missing field weld.
It is important to separate two terms that the exam deliberately confuses. The weld symbol is the small shape that names the weld type (the fillet triangle, the V for a V-groove). The welding symbol is the entire assembly — reference line, arrow, weld symbol, dimensions, tail, and supplementary marks — taken together. The weld symbol is one element inside the welding symbol.
The Eight Elements of a Complete Welding Symbol
A2.4 builds every welding symbol from a fixed set of standard locations. Each element has one correct place, and reading the symbol means decoding each location in turn.
Element Standard location What it conveys
Reference line Horizontal line — always present, always horizontal The backbone; everything is read relative to it (above vs. below)
Arrow One end of the reference line, bent to point at the joint Identifies which joint and establishes the arrow side
Weld symbol Touching the reference line, above and/or below The weld type (fillet, groove, plug, slot, spot, seam, etc.)
Dimensions Left of the weld symbol = size; right = length/pitch Leg/throat/depth, length, and intermittent spacing
Tail Forked end opposite the arrow Process abbreviation, specification, WPS number, or notes
Supplementary symbols At the junction or on the weld symbol Field weld, weld-all-around, contour, backing, spacer, melt-through
- Finish symbols Above/over the contour symbol Method to achieve the contour: G, M, C, R, H
- NDE / examination symbols On or near the reference line Required examination method (RT, UT, MT, PT, VT)
The reference line is always drawn horizontal , no matter how the joint is oriented on the drawing — a vertical seam on a tank still gets a horizontal reference line with the arrow bent to reach it. The tail is optional : it appears only when the designer needs to specify a process, a procedure, or a note, and it is omitted when no reference is needed.
Arrow Side vs. Other Side — the Make-or-Break Convention
This single convention is the most heavily tested idea in the entire symbols topic, and it trips up candidates who memorize it backwards. Fix it once and never invert it:
The arrow side is the side of the joint the arrow physically touches/points to.
The other side is the opposite face of that same joint.
A weld symbol below the reference line = a weld on the arrow side .
A weld symbol above the reference line = a weld on the other side .
A weld symbol both above and below = welds on both sides of the joint.
Memory aid: "Below = By the arrow." The mark below the line is the weld nearest the arrow's side. Note the deliberate inversion — below the line means the arrow side, which feels backwards until drilled.
The same above/below logic carries to dimensions and supplementary data: information placed below the reference line describes the arrow-side weld, and information above describes the other-side weld. For symmetrical or non-sided welds (square-groove, plug, spot, seam, flush) the symbol is centered and the above/below distinction does not apply.
The Weld Symbols (Shape Characters)
- Shape Weld type
- Triangle (right-angle) Fillet weld
- Two parallel verticals Square-groove (no edge preparation)
- V V-groove
- Half-V (one straight side) Bevel-groove (perpendicular leg = broken arrow points to the prepared member)
- U U-groove
- J J-groove (broken arrow points to the prepared member)
- Two angled lines meeting / curved pair Flare-V and flare-bevel groove (for rounded edges/tubing)
- Circle in a rectangle Plug or slot weld
- Two parallel horizontals Seam weld
- Circle Spot or projection weld
For the bevel and J grooves only one member is prepared, so A2.4 uses a break (jog) in the arrow line that bends toward the member that gets the bevel or J preparation. If you see a kinked arrow, it is telling you which plate to cut.
Supplementary Symbols
- Supplementary mark Location Meaning
- Flag At the arrow/reference-line junction Field weld — made at the erection site, not in the shop
- Open circle At the junction Weld-all-around — continuous around the whole joint perimeter
- Straight line over the weld symbol On the weld symbol Flush/flat contour
- Convex arc On the weld symbol Convex contour
- Concave arc On the weld symbol Concave contour
- Letter over the contour symbol Above contour Finish method: G grind, M machine, C chip, R roll, H hammer
- Filled rectangle Opposite the groove Backing (backing bar / backing weld)
- Open rectangle In the joint Spacer
Dimensioning Fillet and Groove Welds
The dimension layout follows a fixed left/right rule that A2.4 never changes: size is to the LEFT of the weld symbol, length is to the RIGHT.
, 5/16 ). The number(s) to the right give length and, for intermittent welds, pitch in a length-pitch pair. So 1/4 (left) with 3-8 (right) reads as a 1/4 in leg, 3 in long weld segments on 8 in center-to-center pitch . The single most common misread is treating pitch as the gap between welds — pitch is center-to-center, so the unwelded gap = pitch minus weld length (here 8 − 3 = 5 in clear). Unequal legs are written (a x b) to the left.
Intermittent welds on both sides are chain (segments aligned across the joint, symbols opposite each other) or staggered (segments offset by half a pitch, symbols offset above/below the line).
Groove welds. Groove dimensioning packs several numbers into and around the symbol:
- Groove dimension Where it appears Example
- Depth of bevel preparation Left of the symbol, no parentheses 1/2
- Groove weld size (effective throat) Left of the symbol, in parentheses (3/8)
- Root opening Inside the weld symbol 1/8 between the lines
- Groove angle (included angle) Outside/above the symbol 60°
For a complete-joint-penetration (CJP) weld the size equals the joint thickness, so it is often left blank or noted "CJP" in the tail rather than dimensioned. When both a depth and a parenthetical size appear, the depth is the bevel cut and the parenthetical value is the effective throat actually credited for strength.
Reading a Symbol End to End
A disciplined CWI reads every welding symbol the same way: identify the joint via the arrow; read the weld symbol below the line (arrow side) and above (other side); read size to the left, length-pitch to the right; check the junction for a flag (field) or circle (all-around); check the weld symbol for contour and finish; then read the tail for process/WPS/spec.
Exam focus: Welding symbols are roughly 10% of Part A (~15 questions) , and the arrow-side/other-side convention is the single most frequently tested item. Drill it, drill the left-size/right-length rule, and drill the junction marks (flag = field, circle = all-around) until they are automatic — these are reliable points.