Study guide

4.1 Linear Motion & Motion Under Gravity

EASA Part-66 Module 02 — Physics Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Syllabus Map & Knowledge Levels

2 Chapter 2: Matter

2.1 Nature of Matter: Elements & Atomic Structure 2.2 Molecules & Chemical Compounds 2.3 States of Matter & Changes of State

3 Chapter 3: Mechanics — Statics

3.1 Forces, Moments, Couples & Vectors 3.2 Centre of Gravity 3.3 Stress, Strain, Elasticity & Hooke's Law 3.4 Pressure, Buoyancy & Barometers

4 Chapter 4: Mechanics — Kinetics

4.1 Linear Motion & Motion Under Gravity 4.2 Uniform Circular Motion (Centripetal/Centrifugal) 4.3 Periodic Motion, Vibration, Harmonics & Resonance 4.4 Mechanical Advantage, Velocity Ratio & Efficiency

5 Chapter 5: Mechanics — Dynamics

5.1 Mass, Force, Inertia & Newton's Laws 5.2 Work, Power & Energy 5.3 Momentum, Conservation of Momentum & Impulse 5.4 Gyroscopic Principles & Friction

6 Chapter 6: Fluid Dynamics

6.1 Density & Specific Gravity 6.2 Viscosity, Streamlining & Compressibility 6.3 Bernoulli's Theorem, Pressure Types & Venturi

7 Chapter 7: Thermodynamics

7.1 Temperature Scales & Heat Definition 7.2 Heat Capacity, Transfer Modes & Volumetric Expansion 7.3 Gas Laws, Thermodynamic Laws & Expanding Gases 7.4 Engine Cycles, Latent Heat & Heat of Combustion

8 Chapter 8: Optics (Light)

8.1 Nature of Light & Reflection 8.2 Refraction, Lenses & Fibre Optics

9 Chapter 9: Wave Motion & Sound

9.1 Mechanical Waves, Interference & Standing Waves 9.2 Sound: Speed, Intensity, Pitch, Quality & Doppler Effect

4.1 Linear Motion & Motion Under Gravity

Key Takeaways Explain This Topic AI

Speed is a scalar (distance/time); velocity is a vector (displacement/time) — same magnitude only when motion is in a single straight direction without reversal.

Acceleration a = Δv/Δt; uniform acceleration means constant a, which is the assumption behind the three constant-acceleration equations of motion.

The constant-acceleration equations are v = u + at, s = ut + ½at², and v² = u² + 2as (SI: m/s, m/s², m).

Near Earth’s surface, free-fall acceleration is g ≈ 9.81 m/s² downward (often 9.8 or 10 m/s² in exam estimates); air resistance is neglected unless stated.

Kinematic problems for dropped tools, launched parts, and vertical climb/descent are solved by choosing a sign convention and substituting carefully into the equations.

Last updated: July 2026

Linear Motion & Motion Under Gravity

Kinetics (in the Part-66 syllabus sense of Mechanics — Kinetics ) studies how bodies move: how far, how fast, and how their speed changes with time. Chapter 3 covered forces and equilibrium when things stay put; this section treats rectilinear (straight-line) motion with constant acceleration, including free fall. Dynamics (Newton’s laws linking force to acceleration) follows in the next chapter — here the focus is the kinematic description itself.

Distance, Displacement, Speed, and Velocity

Distance is the total path length travelled. It is always positive and is a scalar . Displacement is the straight-line change of position from start to finish, with direction — a vector . Walking 10 m forward and 10 m back gives distance 20 m but displacement 0.

Speed is the rate of covering distance:

speed = distance / time

Units: metres per second (m/s). Average speed uses total distance over total time; instantaneous speed is the limit as the time interval shrinks.

Velocity is the rate of change of displacement:

velocity = displacement / time

Velocity is a vector — magnitude and direction. If an aircraft taxis 200 m north in 40 s, its average velocity is 5 m/s north. The average speed is also 5 m/s if it went only north; reverse or turn, and speed and the magnitude of average velocity diverge.

Exam trap: a quantity without direction stated is often speed; “20 m/s east” is velocity. Average velocity over a closed path can be zero while average speed is not.

Acceleration

Acceleration is the rate of change of velocity:

a = (v − u) / t or a = Δv / Δt

where u is initial velocity, v is final velocity, and t is the time interval. SI unit: m/s² . Acceleration is a vector. Speeding up in the direction of travel is positive acceleration in that sense; slowing down (deceleration) is acceleration opposite the velocity. A body can have constant speed and still accelerate if direction changes (circular motion — next section).

Uniform (constant) acceleration means a does not change with time. That idealisation is excellent for many Module 2 problems: braking on a runway approximation, free fall without air resistance, and constant-thrust start rolls treated as constant a .

Worked example — taxi acceleration. An aircraft starts from rest (u = 0) and reaches 30 m/s in 20 s along a straight taxiway. Acceleration is:

a = (30 − 0) / 20 = 1.5 m/s²

If it later brakes from 30 m/s to rest in 15 s:

  • a = (0 − 30) / 15 = −2.0 m/s²
  • (The negative sign means opposite the positive-forward direction.)
  • Equations of Motion (Constant Acceleration)

When acceleration is constant, three core equations relate u , v , a , t , and displacement s :

  • v = u + at
  • s = ut + ½at²
  • v² = u² + 2as

(A fourth form, s = ½(u + v)t, follows from average velocity under constant a , but the three above cover nearly all exam work.)

How to choose which equation. List the knowns and the unknown. Use (1) when you need v or t and s is missing. Use (2) when s is required and v is missing. Use (3) when t is missing and you know or need s with speeds. Always fix a sign convention first: pick a positive direction (e.g. upward, or along the runway) and keep u , v , a , and s consistent with it.

Worked example — distance under constant acceleration. A trolley on a hangar floor accelerates from rest at 0.8 m/s² for 5.0 s. Distance travelled:

s = ut + ½at² = 0 + ½(0.8)(5.0)² = 0.4 × 25 = 10 m

Final speed: v = 0 + 0.8 × 5 = 4.0 m/s . Check with (3): v² = 0 + 2(0.8)(10) = 16 ⇒ v = 4.0 m/s. Consistent.

Worked example — stopping distance. A vehicle approaches a stop mark at 12 m/s and brakes with constant deceleration of magnitude 3.0 m/s². Take forward as positive: u = 12 m/s, v = 0, a = −3.0 m/s². From (3):

0 = 12² + 2(−3.0)s ⇒ 0 = 144 − 6s ⇒ s = 144/6 = 24 m

Time to stop from (1): 0 = 12 + (−3)t ⇒ t = 4.0 s.

Motion Under Gravity (Free Fall)

Near Earth’s surface, if air resistance is neglected, every freely falling body has the same downward acceleration g . Standard value:

g ≈ 9.81 m/s² (often 9.8 m/s² or 10 m/s² for quick estimates)

“Freely falling” includes objects thrown upward: after release, the only acceleration is still g downward until impact or catch. At the highest point, instantaneous velocity is zero , but acceleration remains g downward — a classic misconception trap.

Sign convention tip. Two common choices:

Positive downward : for a drop from rest, u = 0, a = +g, s positive down.

Positive upward : for a throw upward, u positive, a = −g, and displacement at max height is positive s with v = 0.

Either works if applied consistently.

Worked example — dropped tool. A spanner is dropped from rest from a stand 4.905 m above the hangar floor. Take down positive, g = 9.81 m/s²:

  • v² = u² + 2as = 0 + 2(9.81)(4.905) = 96.26 ⇒ v ≈ 9.81 m/s
  • t from s = ½gt²: 4.905 = ½(9.81)t² ⇒ t² = 1 ⇒ t = 1.0 s

Impact speed about 9.8 m/s after one second of free fall from rest matches the rule of thumb that speed increases by roughly g each second when starting from rest and falling freely.

Worked example — projected upward. A marker is thrown vertically upward at 15 m/s. Take up positive, a = −9.81 m/s². Maximum height (v = 0):

0 = 15² + 2(−9.81)s ⇒ s = 225 / 19.62 ≈ 11.5 m

Time to apex: 0 = 15 − 9.81t ⇒ t ≈ 1.53 s . Total flight time to return to the throw height is twice that (symmetric if landing at same level), about 3.06 s . Speed on return equals launch speed, direction reversed.

Aviation Context

Straight-line kinematics models take-off and landing ground rolls when acceleration is treated as roughly constant, fall times for objects released from height, and relative motion along a single axis (e.g. a part sliding on a straight rail). Real aircraft accelerate under varying thrust and drag — Module 2 expects the ideal constant- a toolkit, not full performance charts. Always state assumptions: constant a , neglect of air resistance for free fall, and SI units throughout.

Quantity Summary

  • Quantity Symbol Type SI unit
  • Distance — Scalar m
  • Displacement s Vector m
  • Speed — Scalar m/s
  • Velocity u, v Vector m/s
  • Acceleration a Vector m/s²
  • Free-fall accel. g Vector (down) ≈ 9.81 m/s²

Master the definitions, the three equations, and free-fall sign discipline — that combination answers the large majority of linear-motion Module 2 items.