Study guide
4.3 Field Effect Transistors & Darlington Pairs
EASA Part-66 Module 04 — Electronic Fundamentals Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Semiconductor Physics & Diode Fundamentals
1.1 Semiconductor Theory, PN Junction & Conduction 1.2 Power Rectification & Filtering Circuits 1.3 Diode Wave-Shaping & Voltage Multipliers
2 Chapter 2: Special-Purpose Diodes & Semiconductor Testing
2.1 Voltage Regulation & Zener Diodes 2.2 Optoelectronic, Fast-Switching & Power Diodes 2.3 Diode Testing, Failure Modes & Aircraft Applications
3 Chapter 3: Transistor Principles, Configurations & Biasing
3.1 BJT Structure, Operation & Current Relationships 3.2 Transistor Circuit Configurations 3.3 Transistor Biasing, Thermal Stability & Testing
4 Chapter 4: Transistor Amplifiers, FETs & Oscillators
4.1 Amplifier Operating Classes & Push-Pull Systems 4.2 Multistage Coupling & Negative Feedback 4.3 Field Effect Transistors & Darlington Pairs 4.4 Oscillators & Multivibrators
5 Chapter 5: Operational Amplifiers & Linear Integrated Circuits
5.1 Op-Amp Fundamentals, Characteristics & Virtual Ground 5.2 Op-Amp Linear Circuits & Calculations 5.3 Active Wave-Shaping, Comparators & Digital Logic Basics
6 Chapter 6: Printed Circuit Boards & Electrostatic Discharge Protection
6.1 PCB Design, Layered Construction & Manufacturing 6.2 PCB Inspection, Soldering Defects & Electrostatic Discharge (ESD) Control
7 Chapter 7: Servomechanism Principles, Transducers & Control
7.1 Open-Loop and Closed-Loop Control Architecture 7.2 Servomechanism Transducers (Potentiometers, LVDTs & RVDTs) 7.3 Servo Dynamics, Damping, Motors & Hunting Prevention
8 Chapter 8: Synchro Systems, Resolvers & Fault Diagnosis
8.1 Torque Synchro Systems (TX, TR & Differentials) 8.2 Control Synchros, Resolvers & Inductive Sensors 8.3 Synchro Troubleshooting, Wiring Faults & Maintenance
4.3 Field Effect Transistors & Darlington Pairs
Key Takeaways Explain This Topic AI
Field Effect Transistors (FETs) are unipolar voltage-controlled devices whose drain current is governed by an electric field across a semiconductor channel, contrasting with current-controlled bipolar junction transistors.
Junction FETs (JFETs) operate with a reverse-biased gate-source PN junction, providing very high input impedance (10^8 to 10^10 Ω) and adhering to Shockley's drain current relationship ID = IDSS(1 - VGS/VP)^2.
MOSFETs utilize an ultra-thin silicon dioxide (SiO2) gate insulating layer, resulting in extreme input impedance (>10^12 Ω); they exist as depletion-mode (normally-on) and enhancement-mode (normally-off, requiring VGS(th)) devices.
The sub-microscopic gate dielectric of MOSFETs is catastrophically vulnerable to electrostatic discharge (ESD) as low as 50 V to 100 V, demanding strict Electrostatic Protected Area (EPA) handling procedures.
A Darlington pair cascades two BJTs in a common-collector configuration to achieve overall current gain β_total ≈ β1 · β2 and high input impedance, but incurs a cumulative Vbe drop of ~1.4 V and higher saturation voltage (Vce(sat) ≈ 0.7 to 0.9 V).
Last updated: September 2026
4.3 Field Effect Transistors & Darlington Pairs
While Bipolar Junction Transistors (BJTs) are current-controlled devices relying on both majority and minority charge carriers, Field Effect Transistors (FETs) operate on a fundamentally different semiconductor principle: unipolar conduction controlled by an electrostatic field .
In avionics systems, FETs offer critical advantages over BJTs, including ultra-high input impedance, near-zero DC gate drive current, low thermal noise figures, and superior thermal stability without thermal runaway. Alongside FETs, the composite bipolar Darlington pair provides extreme current amplification required to interface microelectronic flight computers with high-current electro-mechanical aircraft actuators.
1. Unipolar vs. Bipolar Operation: Voltage vs. Current Control
Understanding the foundational distinction between BJTs and FETs is a primary EASA Part-66 Module 04 requirement:
BJT (Bipolar) : Conduction depends on two carrier types (electrons and holes). It is a current-controlled device where a small base current ( I B I_B I B ) controls a large collector current ( I C = β I B I_C = \beta I_B I C = β I B ). Its forward-biased base-emitter junction exhibits moderate input impedance ( 1 k Ω to 5 k Ω 1\text{ k}\Omega\text{ to }5\text{ k}\Omega 1 k Ω to 5 k Ω ).
FET (Unipolar) : Current conduction is carried exclusively by one carrier type (majority electrons in an N-channel, or majority holes in a P-channel) traveling between Source ( S S S ) and Drain ( D D D ) . Current flow is modulated by an electric field established by a voltage applied to the Gate ( G G G ) terminal. Because the gate draws virtually zero DC current, a FET is a voltage-controlled device with immense input impedance ( 10 8 Ω to > 10 12 Ω 10^8\ \Omega\text{ to }>10^{12}\ \Omega 1 0 8 Ω to > 1 0 12 Ω ).
- 2. Junction Field Effect Transistors (JFETs)
- Construction and Physical Mechanism
An N-channel JFET consists of a bar of N-type silicon with ohmic contacts at each end forming the Source and Drain . Two heavily doped P-type regions ( P + P^+ P + ) are diffused into opposing sides of the bar and connected together to form the Gate . N-Channel JFET Biasing:
- Drain is biased positive relative to Source (V_DS > 0)
- Gate is reverse-biased relative to Source (V_GS ≤ 0)
Because the gate-to-channel PN junction is reverse-biased :
A depletion region forms and widens into the N-channel.
As reverse bias ( ∣ V G S ∣ |V_{GS}| ∣ V GS ∣ ) increases, the non-conductive depletion layers expand inward, constricting the cross-sectional area of the conductive N-channel.
The narrower channel increases channel resistance, reducing electron flow from source to drain.
When reverse gate voltage reaches the Pinch-Off Voltage ( V P V_P V P ) , the depletion layers touch, pinching off the channel and limiting drain current to a constant saturation value.
Mathematical Formulation: Shockley's Equation
In the active saturation region (where V D S > ∣ V P ∣ − ∣ V G S ∣ V_{DS} > |V_P| - |V_{GS}| V D S > ∣ V P ∣ − ∣ V GS ∣ ), drain current ( I D I_D I D ) is governed strictly by gate-source voltage ( V G S V_{GS} V GS ) according to Shockley's Equation : I D = I D S S ( 1 − V G S V P ) 2 I_D = I_{DSS} \left(1 - \frac{V_{GS}}{V_P}\right)^2 I D = I D SS ( 1 − V P V GS ) 2
Where:
I D S S I_{DSS} I D SS = Drain-to-Source saturation current with gate shorted to source ( V G S = 0 V V_{GS} = 0\text{ V} V GS = 0 V ).
V P V_P V P = Gate-source pinch-off (cutoff) voltage (negative for N-channel, positive for P-channel).
V G S V_{GS} V GS = Applied gate-to-source reverse bias voltage.
Transconductance ( g m g_m g m )
Because a FET is voltage-controlled, its gain is defined as transconductance ( g m g_m g m ) , measuring the change in output drain current resulting from a change in input gate voltage: g m = Δ I D Δ V G S = g m 0 ( 1 − V G S V P ) where g m 0 = 2 I D S S ∣ V P ∣ g_m = \frac{\Delta I_D}{\Delta V_{GS}} = g_{m0} \left(1 - \frac{V_{GS}}{V_P}\right) \qquad \text{where} \qquad g_{m0} = \frac{2 I_{DSS}}{|V_P|} g m = Δ V GS Δ I D = g m 0 ( 1 − V P V GS ) where g m 0 = ∣ V P ∣ 2 I D SS
Transconductance is measured in millisiemens (mS) or micromhos ( μ mho \mu\text{mho} μ mho ) .
3. Metal-Oxide-Semiconductor FETs (MOSFETs)
In a MOSFET , the metallic or polysilicon gate electrode is completely physically isolated from the semiconductor channel by an ultra-thin insulating dielectric layer of silicon dioxide ( S i O 2 SiO_2 S i O 2 ) :
Input Impedance : Exceeds 10 12 Ω 10^{12}\ \Omega 1 0 12 Ω ( 1 T Ω 1\text{ T}\Omega 1 T Ω ) , drawing negligible leakage current (picoamperes).
A. Depletion-Mode MOSFET (D-MOSFET)
A D-MOSFET is fabricated with a physical conducting channel already present between source and drain. It can operate in two distinct modes:
Depletion Mode : Applying reverse gate bias ( V G S < 0 V_{GS} < 0 V GS < 0 for N-channel) repels channel electrons, depleting the channel and reducing I D I_D I D .
Enhancement Mode : Applying positive gate bias ( V G S > 0 V_{GS} > 0 V GS > 0 for N-channel) attracts additional electrons into the channel, enhancing conductivity and increasing I D I_D I D above I D S S I_{DSS} I D SS .
B. Enhancement-Mode MOSFET (E-MOSFET)
An E-MOSFET has no physical channel built during fabrication . At zero gate bias ( V G S = 0 V V_{GS} = 0\text{ V} V GS = 0 V ), the device is normally-off and no current flows between drain and source ( I D = 0 I_D = 0 I D = 0 ).
Inversion Layer Formation : When a positive gate voltage exceeding the threshold voltage ( V G S ( t h ) V_{GS(th)} V GS ( t h ) ) is applied, the positive electric field repels substrate holes and attracts minority electrons to the S i O 2 SiO_2 S i O 2 interface.
This creates a thin conducting N-type inversion layer bridging the source and drain, turning the transistor ON.
Significance : E-MOSFETs are the foundation of modern digital avionics: complementary pairs of N-channel and P-channel MOSFETs form CMOS (Complementary MOS) logic gates, which consume virtually zero static power in aircraft computers and FADEC systems.
Electrostatic Discharge (ESD) Hazards
The S i O 2 SiO_2 S i O 2 gate insulating layer is sub-microscopically thin (often less than 50 nm 50\text{ nm} 50 nm ). Because the dielectric breakdown strength of S i O 2 SiO_2 S i O 2 is approximately 10 7 V/cm 10^7\text{ V/cm} 1 0 7 V/cm , an electrostatic potential of merely 50 V to 100 V 50\text{ V to }100\text{ V} 50 V to 100 V is sufficient to permanently puncture the dielectric barrier, causing catastrophic short-circuit failure.
Warning
ESD Handling in Aircraft Maintenance : Humans routinely accumulate static charges of 3 , 000 V to 15 , 000 V 3,000\text{ V to }15,000\text{ V} 3 , 000 V to 15 , 000 V simply walking across hangar floors. Handling MOSFETs or CMOS LRU circuit cards without Electrostatic Protected Area (EPA) controls—such as conductive grounded wrist straps with a 1 M Ω 1\text{ M}\Omega 1 M Ω safety resistor, dissipative work mats, and conductive shielding transport bags—will permanently destroy gate insulation or introduce latent gate damage that causes premature in-flight failure.
4. The Darlington Pair Configuration
When flight computer microcontrollers (supplying only milliampere-level logic outputs) must drive high-current inductive aircraft loads (such as 5 A 5\text{ A} 5 A fuel valves, trim tab motors, or relay solenoids), a single BJT lacks sufficient current gain. The Darlington pair solves this by cascading two bipolar transistors into a single composite device.
Circuit Architecture
The collectors of both transistors ( Q 1 Q_1 Q 1 and Q 2 Q_2 Q 2 ) are tied together.
The emitter of the input driver transistor ( Q 1 Q_1 Q 1 ) feeds directly into the base of the main output power transistor ( Q 2 Q_2 Q 2 ). Darlington Topology:
- C (Common Collector Node)
- |---------
- | |
- C1 C2
- B --- B1 B2
- E1 ----->|
- E2 --- E (Composite Emitter Node)
- Composite Parameters
Total Current Gain ( β t o t a l \beta_{total} β t o t a l ) : I C 1 = β 1 I B I B 2 = I E 1 = ( β 1 + 1 ) I B I_{C1} = \beta_1 I_B \qquad I_{B2} = I_{E1} = (\beta_1 + 1) I_B I C 1 = β 1 I B I B 2 = I E 1 = ( β 1 + 1 ) I B I C 2 = β 2 I B 2 = β 2 ( β 1 + 1 ) I B I_{C2} = \beta_2 I_{B2} = \beta_2 (\beta_1 + 1) I_B I C 2 = β 2 I B 2 = β 2 ( β 1 + 1 ) I B I C ( t o t a l ) = I C 1 + I C 2 = [ β 1 + β 2 ( β 1 + 1 ) ] I B ≈ ( β 1 ⋅ β 2 ) I B I_{C(total)} = I_{C1} + I_{C2} = [\beta_1 + \beta_2 (\beta_1 + 1)] I_B \approx (\beta_1 \cdot \beta_2) I_B I C ( t o t a l ) = I C 1 + I C 2 = [ β 1 + β 2 ( β 1 + 1 )] I B ≈ ( β 1 ⋅ β 2 ) I B β t o t a l ≈ β 1 ⋅ β 2 \beta_{total} \approx \beta_1 \cdot \beta_2 β t o t a l ≈ β 1 ⋅ β 2
If Q 1 Q_1 Q 1 has β 1 = 100 \beta_1 = 100 β 1 = 100 and Q 2 Q_2 Q 2 has β 2 = 50 \beta_2 = 50 β 2 = 50 , the composite gain is β t o t a l ≈ 5 , 000 \beta_{total} \approx 5,000 β t o t a l ≈ 5 , 000 .
Composite Input Impedance ( Z i n Z_{in} Z in ) : Z i n ≈ β 1 ⋅ β 2 ⋅ R E Z_{in} \approx \beta_1 \cdot \beta_2 \cdot R_E Z in ≈ β 1 ⋅ β 2 ⋅ R E
This extremely high input impedance minimizes loading on preceding control logic.
Engineering Drawbacks & Trade-Offs
Double Base-Emitter Drop : V B E ( t o t a l ) = V B E 1 + V B E 2 ≈ 0.7 V + 0.7 V = 1.4 V V_{BE(total)} = V_{BE1} + V_{BE2} \approx 0.7\text{ V} + 0.7\text{ V} = 1.4\text{ V} V BE ( t o t a l ) = V BE 1 + V BE 2 ≈ 0.7 V + 0.7 V = 1.4 V The control signal must exceed 1.4 V 1.4\text{ V} 1.4 V before conduction can begin.
Elevated Saturation Voltage : V C E ( s a t ) = V C E 1 ( s a t ) + V B E 2 ≈ 0.2 V + 0.7 V = 0.9 V V_{CE(sat)} = V_{CE1(sat)} + V_{BE2} \approx 0.2\text{ V} + 0.7\text{ V} = 0.9\text{ V} V CE ( s a t ) = V CE 1 ( s a t ) + V BE 2 ≈ 0.2 V + 0.7 V = 0.9 V Unlike a single saturated BJT ( V C E ( s a t ) ≈ 0.1 to 0.2 V V_{CE(sat)} \approx 0.1\text{ to }0.2\text{ V} V CE ( s a t ) ≈ 0.1 to 0.2 V ), a Darlington cannot saturate below 0.7 – 0.9 V 0.7\text{–}0.9\text{ V} 0.7 – 0.9 V . At high load currents (e.g., 10 A 10\text{ A} 10 A ), this causes significant power dissipation ( P = 0.9 V × 10 A = 9.0 W P = 0.9\text{ V} \times 10\text{ A} = 9.0\text{ W} P = 0.9 V × 10 A = 9.0 W ), requiring substantial heat sinking.
Turn-Off Delay : Trapped base charge in Q 2 Q_2 Q 2 cannot discharge quickly when Q 1 Q_1 Q 1 turns off. Practical Darlington devices integrate internal base-emitter "bleed" resistors to speed up turn-off switching.
Comparison: BJT vs. JFET vs. MOSFET vs. Darlington
Parameter BJT JFET MOSFET (Enhancement) Darlington Pair
Control Mechanism Current-controlled ( I B I_B I B ) Voltage-controlled ( V G S V_{GS} V GS ) Voltage-controlled ( V G S V_{GS} V GS ) Current-controlled ( I B I_B I B )
Carrier Type Bipolar (electrons & holes) Unipolar (single majority) Unipolar (single majority) Bipolar (two stages)
Input Impedance Moderate ( 1 − 5 k Ω 1 - 5\text{ k}\Omega 1 − 5 k Ω ) Very High ( 10 8 − 10 10 Ω 10^8 - 10^{10}\ \Omega 1 0 8 − 1 0 10 Ω ) Extremely High ( > 10 12 Ω >10^{12}\ \Omega > 1 0 12 Ω ) High ( 100 k Ω − 1 M Ω 100\text{ k}\Omega - 1\text{ M}\Omega 100 k Ω − 1 M Ω )
Current Gain β ≈ 50 − 300 \beta \approx 50 - 300 β ≈ 50 − 300 N/A ( g m ≈ 2 − 10 mS g_m \approx 2 - 10\text{ mS} g m ≈ 2 − 10 mS ) N/A ( g m ≈ 5 − 50 mS g_m \approx 5 - 50\text{ mS} g m ≈ 5 − 50 mS ) Extreme ( β 1 β 2 ≈ 1000 − 10000 \beta_1 \beta_2 \approx 1000 - 10000 β 1 β 2 ≈ 1000 − 10000 )
Turn-On Voltage V B E ≈ 0.7 V V_{BE} \approx 0.7\text{ V} V BE ≈ 0.7 V Normally ON ( V G S = 0 V_{GS}=0 V GS = 0 ) V G S ( t h ) ≈ 1.5 − 4.0 V V_{GS(th)} \approx 1.5 - 4.0\text{ V} V GS ( t h ) ≈ 1.5 − 4.0 V V B E ≈ 1.4 V V_{BE} \approx 1.4\text{ V} V BE ≈ 1.4 V
- Thermal Runaway Vulnerable Immune (negative temp coeff) Immune (negative temp coeff) Vulnerable
- Static Sensitivity Low Low Extreme (catastrophic ESD) Low
- Worked Engineering Calculation: JFET Shockley Operating Point
- Problem
An avionics fuel quantity sensor interface employs an N-channel JFET in its preamplifier stage. The manufacturer datasheet specifies:
- Drain saturation current at zero bias: I D S S = 12.0 mA I_{DSS} = 12.0\text{ mA} I D SS = 12.0 mA
- Pinch-off voltage: V P = − 4.0 V V_P = -4.0\text{ V} V P = − 4.0 V
If the bias circuit establishes a gate-to-source voltage V G S = − 1.5 V V_{GS} = -1.5\text{ V} V GS = − 1.5 V , calculate:
The quiescent drain current ( I D I_D I D ).
The zero-bias transconductance ( g m 0 g_{m0} g m 0 ).
The operating transconductance ( g m g_m g m ) at V G S = − 1.5 V V_{GS} = -1.5\text{ V} V GS = − 1.5 V .
Solution
Quiescent Drain Current ( I D I_D I D ) :
Using Shockley's Equation: I D = I D S S ( 1 − V G S V P ) 2 = 12.0 mA × ( 1 − − 1.5 V − 4.0 V ) 2 I_D = I_{DSS} \left(1 - \frac{V_{GS}}{V_P}\right)^2 = 12.0\text{ mA} \times \left(1 - \frac{-1.5\text{ V}}{-4.0\text{ V}}\right)^2 I D = I D SS ( 1 − V P V GS ) 2 = 12.0 mA × ( 1 − − 4.0 V − 1.5 V ) 2 I D = 12.0 mA × ( 1 − 0.375 ) 2 = 12.0 mA × ( 0.625 ) 2 = 12.0 mA × 0.390625 ≈ 4.69 mA I_D = 12.0\text{ mA} \times (1 - 0.375)^2 = 12.0\text{ mA} \times (0.625)^2 = 12.0\text{ mA} \times 0.390625 \approx 4.69\text{ mA} I D = 12.0 mA × ( 1 − 0.375 ) 2 = 12.0 mA × ( 0.625 ) 2 = 12.0 mA × 0.390625 ≈ 4.69 mA
Zero-Bias Transconductance ( g m 0 g_{m0} g m 0 ) : g m 0 = 2 I D S S ∣ V P ∣ = 2 × 12.0 mA ∣ − 4.0 V ∣ = 24.0 mA 4.0 V = 6.0 mS = 6000 μ S g_{m0} = \frac{2 I_{DSS}}{|V_P|} = \frac{2 \times 12.0\text{ mA}}{|-4.0\text{ V}|} = \frac{24.0\text{ mA}}{4.0\text{ V}} = 6.0\text{ mS} = 6000\ \mu\text{S} g m 0 = ∣ V P ∣ 2 I D SS = ∣ − 4.0 V ∣ 2 × 12.0 mA = 4.0 V 24.0 mA = 6.0 mS = 6000 μ S
Operating Transconductance ( g m g_m g m ) : g m = g m 0 ( 1 − V G S V P ) = 6.0 mS × ( 1 − 0.375 ) = 6.0 mS × 0.625 = 3.75 mS = 3750 μ S g_m = g_{m0} \left(1 - \frac{V_{GS}}{V_P}\right) = 6.0\text{ mS} \times (1 - 0.375) = 6.0\text{ mS} \times 0.625 = 3.75\text{ mS} = 3750\ \mu\text{S} g m = g m 0 ( 1 − V P V GS ) = 6.0 mS × ( 1 − 0.375 ) = 6.0 mS × 0.625 = 3.75 mS = 3750 μ S
Every 1.0 V 1.0\text{ V} 1.0 V change in gate voltage will cause a 3.75 mA 3.75\text{ mA} 3.75 mA change in drain current.