Study guide
4.4 Oscillators & Multivibrators
EASA Part-66 Module 04 — Electronic Fundamentals Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Semiconductor Physics & Diode Fundamentals
1.1 Semiconductor Theory, PN Junction & Conduction 1.2 Power Rectification & Filtering Circuits 1.3 Diode Wave-Shaping & Voltage Multipliers
2 Chapter 2: Special-Purpose Diodes & Semiconductor Testing
2.1 Voltage Regulation & Zener Diodes 2.2 Optoelectronic, Fast-Switching & Power Diodes 2.3 Diode Testing, Failure Modes & Aircraft Applications
3 Chapter 3: Transistor Principles, Configurations & Biasing
3.1 BJT Structure, Operation & Current Relationships 3.2 Transistor Circuit Configurations 3.3 Transistor Biasing, Thermal Stability & Testing
4 Chapter 4: Transistor Amplifiers, FETs & Oscillators
4.1 Amplifier Operating Classes & Push-Pull Systems 4.2 Multistage Coupling & Negative Feedback 4.3 Field Effect Transistors & Darlington Pairs 4.4 Oscillators & Multivibrators
5 Chapter 5: Operational Amplifiers & Linear Integrated Circuits
5.1 Op-Amp Fundamentals, Characteristics & Virtual Ground 5.2 Op-Amp Linear Circuits & Calculations 5.3 Active Wave-Shaping, Comparators & Digital Logic Basics
6 Chapter 6: Printed Circuit Boards & Electrostatic Discharge Protection
6.1 PCB Design, Layered Construction & Manufacturing 6.2 PCB Inspection, Soldering Defects & Electrostatic Discharge (ESD) Control
7 Chapter 7: Servomechanism Principles, Transducers & Control
7.1 Open-Loop and Closed-Loop Control Architecture 7.2 Servomechanism Transducers (Potentiometers, LVDTs & RVDTs) 7.3 Servo Dynamics, Damping, Motors & Hunting Prevention
8 Chapter 8: Synchro Systems, Resolvers & Fault Diagnosis
8.1 Torque Synchro Systems (TX, TR & Differentials) 8.2 Control Synchros, Resolvers & Inductive Sensors 8.3 Synchro Troubleshooting, Wiring Faults & Maintenance
4.4 Oscillators & Multivibrators
Key Takeaways Explain This Topic AI
Sustained sinusoidal oscillation requires satisfying the two Barkhausen criteria: a closed-loop gain magnitude of exactly unity (|Aβ| = 1) and a net loop phase shift of 0° or 360°.
LC resonant tank oscillators interchange electrostatic and magnetic energy at frequency f0 = 1 / (2π√(LC)), with Hartley using a tapped inductor and Colpitts using a capacitive voltage divider.
Colpitts oscillators exhibit superior high-frequency phase stability and lower harmonic distortion compared to Hartley circuits, making them the standard LC architecture in aircraft VHF communications transceivers.
Quartz crystal oscillators utilize the piezoelectric effect to achieve mechanical Q-factors exceeding 100,000 and frequency stability in parts per million (ppm), serving as precision timebases in GPS receivers, weather radar, and TCAS.
Multivibrators are non-sinusoidal relaxation circuits categorized into astable (free-running clock generators), monostable (one-shot timing pulse generators), and bistable (two-state digital memory flip-flops).
Last updated: September 2026
4.4 Oscillators & Multivibrators
In aircraft avionics, electronic signal generators are divided into two fundamental classes:
Sinusoidal Oscillators : Generate pure, single-frequency sine waves for radio frequency (RF) communications carrier waves, radar local oscillators, VHF omnidirectional range (VOR) navigation receivers, and synchro system 400 Hz excitation references.
Multivibrators (Relaxation Oscillators) : Generate non-sinusoidal digital clock waveforms, rectangular pulses, and square waves used in flight management computer clocks, radar range gate timing, Distance Measuring Equipment (DME) pulse decoding, and cockpit indicator flashers.
1. Principles of Sinusoidal Oscillation & The Barkhausen Criteria
An oscillator is essentially an amplifier that generates an AC output signal from a DC power supply without requiring any external AC input signal . It achieves this by taking a portion of its output voltage and feeding it back to the input in positive (regenerative) feedback .
The Two Barkhausen Criteria
For an amplifier-feedback loop to sustain continuous, stable sinusoidal oscillation at a designated frequency ( f 0 f_0 f 0 ), the system must satisfy the Barkhausen Criteria :
Loop Gain Magnitude Criterion : ∣ A ⋅ β ∣ = 1 |A \cdot \beta| = 1 ∣ A ⋅ β ∣ = 1
At Startup : The initial loop gain must be slightly greater than unity ( ∣ A β ∣ > 1 |A\beta| > 1 ∣ A β ∣ > 1 ). This allows tiny, broadband thermal noise voltages across the circuit components to be progressively amplified and filtered around f 0 f_0 f 0 , rapidly building up the oscillation amplitude.
At Steady-State : As the oscillation reaches the desired amplitude, non-linearities in the transistor (such as saturation/cutoff limiting or automatic gain control) compress the amplifier gain until the effective loop gain stabilizes at exactly unity ( ∣ A β ∣ = 1 |A\beta| = 1 ∣ A β ∣ = 1 ) . If ∣ A β ∣ < 1 |A\beta| < 1 ∣ A β ∣ < 1 , oscillations decay exponentially to zero; if ∣ A β ∣ > 1 |A\beta| > 1 ∣ A β ∣ > 1 , the waveform grows until severe clipping occurs.
Phase Shift Criterion : ∠ ( A ⋅ β ) = 0 ∘ or 360 ∘ \angle (A \cdot \beta) = 0^\circ \quad \text{or} \quad 360^\circ ∠ ( A ⋅ β ) = 0 ∘ or 36 0 ∘
A standard Common Emitter (CE) transistor amplifier stage introduces an intrinsic 180 ∘ 180^\circ 18 0 ∘ phase inversion between base and collector.
Therefore, the external frequency-determining feedback network must introduce an additional 180 ∘ 180^\circ 18 0 ∘ phase shift precisely at frequency f 0 f_0 f 0 .
Total round-trip phase shift: 180 ∘ + 180 ∘ = 360 ∘ ≡ 0 ∘ 180^\circ + 180^\circ = 360^\circ \equiv 0^\circ 18 0 ∘ + 18 0 ∘ = 36 0 ∘ ≡ 0 ∘ (in-phase regenerative feedback).
2. LC Resonant Tank Oscillators
At radio frequencies ( 100 kHz to > 500 MHz 100\text{ kHz to }>500\text{ MHz} 100 kHz to > 500 MHz ), frequency determination relies on a parallel LC resonant tank circuit . In an ideal tank, energy continuously cycles between the electric field of capacitor C C C ( E = 1 2 C V 2 E = \frac{1}{2} C V^2 E = 2 1 C V 2 ) and the magnetic field of inductor L L L ( E = 1 2 L I 2 E = \frac{1}{2} L I^2 E = 2 1 L I 2 ) at the natural resonant frequency: f 0 = 1 2 π L C f_0 = \frac{1}{2\pi \sqrt{L C}} f 0 = 2 π L C 1
Because practical inductors possess internal winding resistance ( R s R_s R s ), energy is dissipated as heat, producing damped (decaying) oscillations. The active transistor injects a pulse of energy each cycle to replenish these losses.
A. The Hartley Oscillator
In a Hartley oscillator , the frequency-determining feedback network employs an inductive voltage divider formed by a center-tapped inductor ( L 1 L_1 L 1 and L 2 L_2 L 2 ) tuned by a single parallel capacitor ( C C C ):
Feedback Ratio : β ≈ L 1 L 2 \beta \approx \frac{L_1}{L_2} β ≈ L 2 L 1 (ratio of feedback winding to collector winding).
Total Inductance : L e q = L 1 + L 2 + 2 M L_{eq} = L_1 + L_2 + 2M L e q = L 1 + L 2 + 2 M (accounting for mutual inductance M M M ).
Resonant Frequency : f 0 = 1 2 π L e q C f_0 = \frac{1}{2\pi \sqrt{L_{eq} C}} f 0 = 2 π L e q C 1
Characteristics : Readily tuned over a wide frequency band using a single variable capacitor. However, parasitic inter-turn capacitance in the tapped coil can introduce harmonic distortion at VHF frequencies.
B. The Colpitts Oscillator
In a Colpitts oscillator , the feedback network uses a capacitive voltage divider consisting of two series capacitors ( C 1 C_1 C 1 and C 2 C_2 C 2 ) in parallel with a single untapped inductor ( L L L ):
Series Equivalent Capacitance : C e q = C 1 ⋅ C 2 C 1 + C 2 C_{eq} = \frac{C_1 \cdot C_2}{C_1 + C_2} C e q = C 1 + C 2 C 1 ⋅ C 2
Resonant Frequency : f 0 = 1 2 π L ⋅ C e q f_0 = \frac{1}{2\pi \sqrt{L \cdot C_{eq}}} f 0 = 2 π L ⋅ C e q 1
Feedback Fraction : β ≈ C 1 C 2 \beta \approx \frac{C_1}{C_2} β ≈ C 2 C 1 (voltage tapped across C 2 C_2 C 2 for base feedback).
Superiority in Avionics : The capacitors in the divider provide a low-reactance shunt to ground for high-order harmonics, yielding a substantially cleaner sinusoidal waveform than the Hartley. It exhibits superior frequency stability at high frequencies, making it the premier LC architecture in aircraft VHF communications transceivers (118.000–136.975 MHz).
3. Quartz Crystal Oscillators
While discrete LC oscillators achieve frequency stabilities of roughly 1 % 1\% 1% to 0.1 % 0.1\% 0.1% , modern aviation communications, navigation, and radar demand tolerances better than 0.0001 % 0.0001\% 0.0001% (1 to 10 parts per million, ppm) . This precision is achieved using quartz crystal oscillators .
The Piezoelectric Effect & Equivalent Circuit
Quartz ( SiO 2 \text{SiO}_2 SiO 2 ) exhibits the piezoelectric effect : applying a mechanical stress across the crystal wafer generates a proportional voltage across its faces; conversely, applying an alternating voltage causes the crystal to vibrate mechanically at its natural acoustic resonant frequency.
Electrically, a mounted quartz crystal behaves as a complex RLC network:
Motional Arm ( L m , C m , R s L_m, C_m, R_s L m , C m , R s ) : L m L_m L m represents the vibrating mechanical mass of the quartz (often several Henries); C m C_m C m represents mechanical elasticity/compliance (fractions of a picofarad); R s R_s R s represents internal acoustic frictional losses (a few ohms).
Static Capacitance ( C 0 C_0 C 0 ) : Represents the electrostatic capacitance formed by the mounting metal electrodes sandwiching the quartz dielectric. Crystal Equivalent Electrical Model:
- --[ Lm ]---[ Cm ]---[ Rs ]--- (Motional Arm)
- |---| |---|
- | ------------[ C0 ]------------ | (Shunt Arm)
- Dual Resonance and Extreme Q-Factor
The crystal exhibits two resonant frequencies separated by only a few kilohertz:
Series Resonant Frequency ( f s f_s f s ) : The motional arm impedance drops to its minimum ( R s R_s R s ): f s = 1 2 π L m C m f_s = \frac{1}{2\pi \sqrt{L_m C_m}} f s = 2 π L m C m 1
Parallel Antiresonant Frequency ( f p f_p f p ) : The inductance L m L_m L m resonates with the series combination of C m C_m C m and C 0 C_0 C 0 , creating an extremely high parallel impedance.
Why Crystals Dominate Aviation
Quality Factor ( Q Q Q ) : The ratio of stored reactive energy to dissipated energy is Q = ω L m R s Q = \frac{\omega L_m}{R_s} Q = R s ω L m . Discrete LC tanks achieve Q ≈ 50 to 200 Q \approx 50\text{ to }200 Q ≈ 50 to 200 . A quartz crystal achieves Q > 10 , 000 to 1 , 000 , 000 Q > 10,000\text{ to }1,000,000 Q > 10 , 000 to 1 , 000 , 000 .
Stability : Extreme Q Q Q yields an extraordinarily steep phase-versus-frequency curve: any circuit drift attempts to shift phase, but a minute frequency shift restores equilibrium, locking the frequency.
Aviation Standards : Temperature-Compensated Crystal Oscillators (TCXO) and Oven-Controlled Crystal Oscillators (OCXO) serve as master clocks in GPS navigation receivers, Mode-S transponders, and Traffic Collision Avoidance Systems (TCAS).
4. Multivibrators: Non-Sinusoidal Relaxation Oscillators
Unlike sinusoidal oscillators that cycle energy between reactive components, multivibrators are relaxation circuits that operate by alternately switching cross-coupled active transistors between full saturation (ON) and cutoff (OFF).
A. Astable Multivibrator (Free-Running Clock)
State Characteristics : Zero stable states ; two quasi-stable states.
Operation : Two cross-coupled BJT stages have their collectors connected to opposing bases via timing capacitors ( C 1 , C 2 C_1, C_2 C 1 , C 2 ) and pull-up resistors ( R 1 , R 2 R_1, R_2 R 1 , R 2 ). The circuit continuously toggles between states as the capacitors alternately charge and discharge.
Output : Continuous square-wave pulse train.
Frequency and Period : T 1 = 0.693 R 1 C 1 T 2 = 0.693 R 2 C 2 T_1 = 0.693 R_1 C_1 \qquad T_2 = 0.693 R_2 C_2 T 1 = 0.693 R 1 C 1 T 2 = 0.693 R 2 C 2 T t o t a l = T 1 + T 2 ≈ 1.386 R C ( for symmetric R 1 = R 2 , C 1 = C 2 ) T_{total} = T_1 + T_2 \approx 1.386 R C \quad (\text{for symmetric } R_1=R_2, C_1=C_2) T t o t a l = T 1 + T 2 ≈ 1.386 RC ( for symmetric R 1 = R 2 , C 1 = C 2 ) f = 1 T t o t a l = 1 1.386 R C ≈ 0.72 R C f = \frac{1}{T_{total}} = \frac{1}{1.386 R C} \approx \frac{0.72}{R C} f = T t o t a l 1 = 1.386 RC 1 ≈ RC 0.72
Avionics Application : Master clock pulse generation for digital logic circuits, flasher units for warning annunciator lights.
B. Monostable Multivibrator (One-Shot Pulse Generator)
State Characteristics : One permanently stable state ; one quasi-stable state.
Operation : Normally rests in its stable state with Q 1 Q_1 Q 1 OFF and Q 2 Q_2 Q 2 ON. An external trigger pulse flips the circuit into its quasi-stable state ( Q 1 Q_1 Q 1 ON, Q 2 Q_2 Q 2 OFF) for a calibrated time duration ( t w t_w t w ) dictated by an RC timing network, after which it automatically snaps back to its resting state.
Pulse Width Equation : t w = ln ( 2 ) ⋅ R C ≈ 0.693 R C t_w = \ln(2) \cdot R C \approx 0.693 R C t w = ln ( 2 ) ⋅ RC ≈ 0.693 RC
Avionics Application : Generating calibrated timing delays, pulse-shaping radar trigger pulses, stretching narrow sensor spikes, and Distance Measuring Equipment (DME) pulse-pair decoders.
C. Bistable Multivibrator (Flip-Flop Data Latch)
State Characteristics : Two permanently stable states ( Q = 1 , Q ˉ = 0 Q = 1, \bar{Q} = 0 Q = 1 , Q ˉ = 0 or Q = 0 , Q ˉ = 1 Q = 0, \bar{Q} = 1 Q = 0 , Q ˉ = 1 ).
Operation : The circuit does not oscillate spontaneously. It remains indefinitely in one stable state until an external trigger pulse forces it to toggle into the opposing state.
Significance : The fundamental 1-bit digital storage element in aviation flight management computers, binary counters, frequency dividers, and register files.
Comparison: Oscillators and Multivibrators
Circuit Type Waveform Generated Stability Mechanism Stable States Primary Avionics Application
Hartley Oscillator Sinusoidal RF Tapped inductor LC resonance 0 0 0 (Linear AC) Wideband tunable radio receivers
Colpitts Oscillator Sinusoidal RF Tapped capacitor LC resonance 0 0 0 (Linear AC) VHF communications local oscillators (118–137 MHz)
Quartz Crystal Pure Sinusoidal Piezoelectric mechanical resonance ( Q > 10 5 Q > 10^5 Q > 1 0 5 ) 0 0 0 (Linear AC) Master clocks: GPS, TCAS, radar, transponders
Astable Multivibrator Square wave / Pulses RC relaxation charging time 0 0 0 (Free-running) Clock pulse generators, cockpit warning flashers
Monostable Multivibrator Single calibrated pulse RC discharge timing ( 0.693 R C 0.693 RC 0.693 RC ) 1 1 1 stable, 1 1 1 quasi Radar range gates, DME pulse-pair timing
Bistable Multivibrator DC logic levels ( 0 0 0 or 1 1 1 ) Cross-coupled DC latched states 2 2 2 stable states 1-bit memory cells, digital registers, binary counters
- Worked Engineering Calculation: Colpitts Oscillator & Astable Clock
- Problem 1: Colpitts Resonant Frequency
An aircraft VHF receiver local oscillator utilizes a Colpitts configuration. The circuit parameters are:
Inductor: L = 1.0 μ H L = 1.0\ \mu\text{H} L = 1.0 μ H
Feedback Capacitors: C 1 = 200 pF C_1 = 200\text{ pF} C 1 = 200 pF and C 2 = 800 pF C_2 = 800\text{ pF} C 2 = 800 pF
Calculate the series equivalent capacitance ( C e q C_{eq} C e q ) and the fundamental oscillation frequency ( f 0 f_0 f 0 ).
Solution 1:
Equivalent Series Capacitance ( C e q C_{eq} C e q ) : C e q = C 1 ⋅ C 2 C 1 + C 2 = 200 pF × 800 pF 200 pF + 800 pF = 160 , 000 1 , 000 = 160 pF = 160 × 10 − 12 F C_{eq} = \frac{C_1 \cdot C_2}{C_1 + C_2} = \frac{200\text{ pF} \times 800\text{ pF}}{200\text{ pF} + 800\text{ pF}} = \frac{160,000}{1,000} = 160\text{ pF} = 160 \times 10^{-12}\text{ F} C e q = C 1 + C 2 C 1 ⋅ C 2 = 200 pF + 800 pF 200 pF × 800 pF = 1 , 000 160 , 000 = 160 pF = 160 × 1 0 − 12 F
Oscillation Frequency ( f 0 f_0 f 0 ) : f 0 = 1 2 π L ⋅ C e q = 1 2 π ( 1.0 × 10 − 6 H ) × ( 160 × 10 − 12 F ) f_0 = \frac{1}{2\pi \sqrt{L \cdot C_{eq}}} = \frac{1}{2\pi \sqrt{(1.0 \times 10^{-6}\text{ H}) \times (160 \times 10^{-12}\text{ F})}} f 0 = 2 π L ⋅ C e q 1 = 2 π ( 1.0 × 1 0 − 6 H ) × ( 160 × 1 0 − 12 F ) 1 1.6 × 10 − 16 = 1.2649 × 10 − 8 s \sqrt{1.6 \times 10^{-16}} = 1.2649 \times 10^{-8}\text{ s} 1.6 × 1 0 − 16 = 1.2649 × 1 0 − 8 s f 0 = 1 2 π × 1.2649 × 10 − 8 = 1 7.9477 × 10 − 8 ≈ 12 , 582 , 200 Hz ≈ 12.58 MHz f_0 = \frac{1}{2\pi \times 1.2649 \times 10^{-8}} = \frac{1}{7.9477 \times 10^{-8}} \approx 12,582,200\text{ Hz} \approx 12.58\text{ MHz} f 0 = 2 π × 1.2649 × 1 0 − 8 1 = 7.9477 × 1 0 − 8 1 ≈ 12 , 582 , 200 Hz ≈ 12.58 MHz
Problem 2: Astable Multivibrator Clock Frequency
A symmetric astable multivibrator used to clock an avionics data logger employs timing resistors R 1 = R 2 = 10 k Ω R_1 = R_2 = 10\text{ k}\Omega R 1 = R 2 = 10 k Ω and timing capacitors C 1 = C 2 = 4.7 nF C_1 = C_2 = 4.7\text{ nF} C 1 = C 2 = 4.7 nF .
Calculate the total period ( T T T ) and the clock frequency ( f f f ).
Solution 2:
Total Period ( T T T ) : T = 1.386 ⋅ R ⋅ C = 1.386 × ( 10 × 10 3 Ω ) × ( 4.7 × 10 − 9 F ) = 1.386 × 4.7 × 10 − 5 s ≈ 65.14 μ s T = 1.386 \cdot R \cdot C = 1.386 \times (10 \times 10^3\ \Omega) \times (4.7 \times 10^{-9}\text{ F}) = 1.386 \times 4.7 \times 10^{-5}\text{ s} \approx 65.14\ \mu\text{s} T = 1.386 ⋅ R ⋅ C = 1.386 × ( 10 × 1 0 3 Ω ) × ( 4.7 × 1 0 − 9 F ) = 1.386 × 4.7 × 1 0 − 5 s ≈ 65.14 μ s
Clock Frequency ( f f f ) : f = 1 T = 1 65.14 × 10 − 6 s ≈ 15 , 350 Hz ≈ 15.35 kHz f = \frac{1}{T} = \frac{1}{65.14 \times 10^{-6}\text{ s}} \approx 15,350\text{ Hz} \approx 15.35\text{ kHz} f = T 1 = 65.14 × 1 0 − 6 s 1 ≈ 15 , 350 Hz ≈ 15.35 kHz