Study guide

5.2 Op-Amp Linear Circuits & Calculations

EASA Part-66 Module 04 — Electronic Fundamentals Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Semiconductor Physics & Diode Fundamentals

1.1 Semiconductor Theory, PN Junction & Conduction 1.2 Power Rectification & Filtering Circuits 1.3 Diode Wave-Shaping & Voltage Multipliers

2 Chapter 2: Special-Purpose Diodes & Semiconductor Testing

2.1 Voltage Regulation & Zener Diodes 2.2 Optoelectronic, Fast-Switching & Power Diodes 2.3 Diode Testing, Failure Modes & Aircraft Applications

3 Chapter 3: Transistor Principles, Configurations & Biasing

3.1 BJT Structure, Operation & Current Relationships 3.2 Transistor Circuit Configurations 3.3 Transistor Biasing, Thermal Stability & Testing

4 Chapter 4: Transistor Amplifiers, FETs & Oscillators

4.1 Amplifier Operating Classes & Push-Pull Systems 4.2 Multistage Coupling & Negative Feedback 4.3 Field Effect Transistors & Darlington Pairs 4.4 Oscillators & Multivibrators

5 Chapter 5: Operational Amplifiers & Linear Integrated Circuits

5.1 Op-Amp Fundamentals, Characteristics & Virtual Ground 5.2 Op-Amp Linear Circuits & Calculations 5.3 Active Wave-Shaping, Comparators & Digital Logic Basics

6 Chapter 6: Printed Circuit Boards & Electrostatic Discharge Protection

6.1 PCB Design, Layered Construction & Manufacturing 6.2 PCB Inspection, Soldering Defects & Electrostatic Discharge (ESD) Control

7 Chapter 7: Servomechanism Principles, Transducers & Control

7.1 Open-Loop and Closed-Loop Control Architecture 7.2 Servomechanism Transducers (Potentiometers, LVDTs & RVDTs) 7.3 Servo Dynamics, Damping, Motors & Hunting Prevention

8 Chapter 8: Synchro Systems, Resolvers & Fault Diagnosis

8.1 Torque Synchro Systems (TX, TR & Differentials) 8.2 Control Synchros, Resolvers & Inductive Sensors 8.3 Synchro Troubleshooting, Wiring Faults & Maintenance

5.2 Op-Amp Linear Circuits & Calculations

Key Takeaways Explain This Topic AI

Negative feedback returns an inverted portion of the output signal to the inverting input, stabilizing closed-loop gain against device variations, widening system bandwidth, and reducing non-linear distortion.

The inverting amplifier produces a closed-loop voltage gain of A_v = -R_f / R_in with a 180° phase inversion, establishing an input impedance equal strictly to the input resistor R_in.

The non-inverting amplifier exhibits a closed-loop voltage gain of A_v = 1 + (R_f / R_1) with 0° phase shift (in-phase) and presents an exceptionally high input impedance that prevents signal loading on sensitive sensors.

The voltage follower (unity-gain buffer) features A_v = 1, zero phase shift, near-infinite input impedance, and near-zero output impedance, serving as an ideal isolation stage for aircraft capacitive fuel probes and piezoelectric sensors.

Inverting summing amplifiers calculate scaled analog additions of flight control command voltages (V_out = -R_f · Σ(V_n / R_n)), while balanced differential instrumentation amplifiers reject common-mode noise to measure strain-gauge and thermocouple micro-voltages.

Last updated: September 2026

5.2 Op-Amp Linear Circuits & Calculations

Operational amplifiers achieve linear, predictable amplification through the deliberate application of negative feedback . By feeding a fraction of the output signal back to the inverting ( − - − ) input terminal, the extreme and temperature-sensitive open-loop gain ( A O L ≈ 10 5 to 10 6 A_{OL} \approx 10^5\text{ to }10^6 A O L ​ ≈ 1 0 5 to 1 0 6 ) is traded for precise, highly stable closed-loop amplification established strictly by external passive resistors. Under the EASA Part-66 syllabus, aircraft maintenance engineers must be capable of deriving circuit transfer functions, calculating component values, assessing input/output impedances, and verifying that signal amplitudes do not violate aircraft DC supply rail saturation boundaries.

The Principle of Negative Feedback

In an open-loop configuration, minor temperature shifts, power supply variations, or minuscule DC offset drifts cause the amplifier output to slam uncontrollably into positive or negative saturation. Negative feedback introduces a feedback network (typically resistors R f R_f R f ​ and R i n R_{in} R in ​ ) that returns an opposing signal to the inverting terminal:

Loading diagram...

The closed-loop gain ( A c l A_{cl} A c l ​ ) of the feedback system is expressed by the classic Black feedback equation: A c l = A O L 1 + β A O L A_{cl} = \frac{A_{OL}}{1 + \beta A_{OL}} A c l ​ = 1 + β A O L ​ A O L ​ ​

Where β \beta β is the feedback transfer factor ( 0 < β ≤ 1 0 < \beta \le 1 0 < β ≤ 1 ). When the open-loop gain is enormous such that β A O L ≫ 1 \beta A_{OL} \gg 1 β A O L ​ ≫ 1 : A c l ≈ A O L β A O L = 1 β A_{cl} \approx \frac{A_{OL}}{\beta A_{OL}} = \frac{1}{\beta} A c l ​ ≈ β A O L ​ A O L ​ ​ = β 1 ​

This fundamental result proves that closed-loop gain is completely independent of internal transistor parameters, temperature drift, and supply fluctuations , depending entirely on the ratio of stable, low-tolerance external metal-film resistors.

The Inverting Amplifier

In the inverting amplifier , the input voltage ( V i n V_{in} V in ​ ) is applied through an input resistor ( R i n R_{in} R in ​ ) to the inverting input ( − - − ), while a feedback resistor ( R f R_f R f ​ ) connects the output ( V o u t V_{out} V o u t ​ ) back to the inverting input. The non-inverting input ( + + + ) is connected directly to circuit ground ( 0 V 0\text{ V} 0 V ). +------------[ Rf ]------------+

  • | |
  • | |\ |
  • V_in o----[ Rin ]--+----| -\ |
  • | \ |
  • 0V --| + >--------------------+----o V_out
  • | /
  • |/
  • Mathematical Derivation via Virtual Ground

Because the non-inverting terminal is grounded ( V + = 0 V V^+ = 0\text{ V} V + = 0 V ), the virtual ground principle dictates that the inverting terminal is also constrained to zero volts: V − = V + = 0 V V^- = V^+ = 0\text{ V} V − = V + = 0 V

Calculate the current flowing into the summing junction from the input source ( I i n I_{in} I in ​ ): I i n = V i n − V − R i n = V i n − 0 R i n = V i n R i n I_{in} = \frac{V_{in} - V^-}{R_{in}} = \frac{V_{in} - 0}{R_{in}} = \frac{V_{in}}{R_{in}} I in ​ = R in ​ V in ​ − V − ​ = R in ​ V in ​ − 0 ​ = R in ​ V in ​ ​

Calculate the feedback current flowing from the summing junction to the output ( I f I_f I f ​ ): I f = V − − V o u t R f = 0 − V o u t R f = − V o u t R f I_f = \frac{V^- - V_{out}}{R_f} = \frac{0 - V_{out}}{R_f} = -\frac{V_{out}}{R_f} I f ​ = R f ​ V − − V o u t ​ ​ = R f ​ 0 − V o u t ​ ​ = − R f ​ V o u t ​ ​

Apply Kirchhoff's Current Law (KCL) at the inverting summing node. Because the ideal op-amp possesses infinite input impedance ( Z i n = ∞ Z_{in} = \infty Z in ​ = ∞ ), zero current enters the inverting terminal pin ( I − = 0 A I^- = 0\text{ A} I − = 0 A ): I i n = I f I_{in} = I_f I in ​ = I f ​

Equating the current expressions: V i n R i n = − V o u t R f ⟹ V o u t V i n = − R f R i n \frac{V_{in}}{R_{in}} = -\frac{V_{out}}{R_f} \implies \frac{V_{out}}{V_{in}} = -\frac{R_f}{R_{in}} R in ​ V in ​ ​ = − R f ​ V o u t ​ ​ ⟹ V in ​ V o u t ​ ​ = − R in ​ R f ​ ​ A v = − R f R i n A_v = -\frac{R_f}{R_{in}} A v ​ = − R in ​ R f ​ ​

Key Inverting Amplifier Characteristics

Phase Inversion: The negative sign designates a 180 ∘ 180^\circ 18 0 ∘ electrical phase shift between input and output.

Input Impedance ( Z i n Z_{in} Z in ​ ): Because the right-hand side of R i n R_{in} R in ​ terminates at the virtual ground node ( 0 V 0\text{ V} 0 V ), the signal source "sees" an input impedance exactly equal to R i n R_{in} R in ​ ( Z i n = R i n Z_{in} = R_{in} Z in ​ = R in ​ ). If R i n R_{in} R in ​ is selected too low, it will load down high-impedance aircraft transducers.

Output Impedance ( Z o u t Z_{out} Z o u t ​ ): Closed-loop negative feedback drives output impedance down to milliohms ( Z o u t ≈ 0 Ω Z_{out} \approx 0\ \Omega Z o u t ​ ≈ 0 Ω ).

The Non-Inverting Amplifier

In the non-inverting amplifier , the input signal ( V i n V_{in} V in ​ ) is connected directly to the high-impedance non-inverting input ( + + + ). Negative feedback is established by a voltage divider network consisting of R f R_f R f ​ and R 1 R_1 R 1 ​ connected from the output to the inverting input ( − - − ). +------------[ Rf ]------------+

  • | |
  • | |\ |
  • +----+----| -\ |
  • | | \ |
  • [R1] V_in-| + >--------------------+----o V_out
  • | | /
  • GND |/
  • Mathematical Derivation

By virtual ground / virtual short tracking, the inverting terminal voltage tracks the non-inverting terminal: V − = V + = V i n V^- = V^+ = V_{in} V − = V + = V in ​

The feedback network forms a resistive voltage divider across V o u t V_{out} V o u t ​ and ground. Because I − = 0 A I^- = 0\text{ A} I − = 0 A , the current flowing down through R 1 R_1 R 1 ​ equals the current through R f R_f R f ​ : V − = V o u t ( R 1 R 1 + R f ) V^- = V_{out} \left( \frac{R_1}{R_1 + R_f} \right) V − = V o u t ​ ( R 1 ​ + R f ​ R 1 ​ ​ )

Equating V − V^- V − to V i n V_{in} V in ​ : V i n = V o u t ( R 1 R 1 + R f ) V_{in} = V_{out} \left( \frac{R_1}{R_1 + R_f} \right) V in ​ = V o u t ​ ( R 1 ​ + R f ​ R 1 ​ ​ )

Rearranging for voltage gain ( A v A_v A v ​ ): A v = V o u t V i n = R 1 + R f R 1 = 1 + R f R 1 A_v = \frac{V_{out}}{V_{in}} = \frac{R_1 + R_f}{R_1} = 1 + \frac{R_f}{R_1} A v ​ = V in ​ V o u t ​ ​ = R 1 ​ R 1 ​ + R f ​ ​ = 1 + R 1 ​ R f ​ ​

Key Non-Inverting Amplifier Characteristics

Zero Phase Shift: The output is in-phase ( 0 ∘ 0^\circ 0 ∘ ) with the input.

Gain Magnitude: Voltage gain is always greater than or equal to unity ( A v ≥ 1 A_v \ge 1 A v ​ ≥ 1 ).

Input Impedance ( Z i n Z_{in} Z in ​ ): Because the input signal connects directly into the op-amp input gate/base with no shunt resistors, the input impedance seen by the source is exceptionally high ( Z i n ≈ Z i n ( o p a m p ) ≥ 10 12 Ω Z_{in} \approx Z_{in(opamp)} \ge 10^{12}\ \Omega Z in ​ ≈ Z in ( o p am p ) ​ ≥ 1 0 12 Ω for BiFET devices), completely eliminating sensor loading errors.

The Voltage Follower (Unity-Gain Buffer)

The voltage follower (or unity-gain buffer) is a critical specialized variant of the non-inverting amplifier where the feedback resistor is replaced by a direct short circuit ( R f = 0 Ω R_f = 0\ \Omega R f ​ = 0 Ω ) and the ground resistor is omitted ( R 1 = ∞ R_1 = \infty R 1 ​ = ∞ ). +------------------------------+

  • | |
  • | |\ |
  • +----| -\ |
  • | \ |
  • V_in-| + >--------------------+----o V_out
  • | /
  • |/

Applying the non-inverting gain equation: A v = 1 + R f R 1 = 1 + 0 ∞ = 1 A_v = 1 + \frac{R_f}{R_1} = 1 + \frac{0}{\infty} = 1 A v ​ = 1 + R 1 ​ R f ​ ​ = 1 + ∞ 0 ​ = 1 V o u t = V i n V_{out} = V_{in} V o u t ​ = V in ​

Avionics Engineering Significance: Impedance Isolation

While a voltage follower provides zero voltage amplification ( A v = 1 A_v = 1 A v ​ = 1 , or 0 dB 0\text{ dB} 0 dB ), it provides immense power gain by performing an impedance transformation:

Input Impedance: Extremely high ( Z i n ≈ 10 9 to 10 12 Ω Z_{in} \approx 10^9\text{ to }10^{12}\ \Omega Z in ​ ≈ 1 0 9 to 1 0 12 Ω ).

Output Impedance: Extremely low ( Z o u t ≈ 0.01 to 0.1 Ω Z_{out} \approx 0.01\text{ to }0.1\ \Omega Z o u t ​ ≈ 0.01 to 0.1 Ω ).

Note

Avionics Sensor Isolation: Modern aircraft use high-impedance sensors such as capacitive fuel quantity probes, piezoelectric engine vibration accelerometers, and ceramic cylinder pressure transducers. These devices can supply only micro-amperes of current. Connecting them directly to low-impedance filter networks, transmission lines, or analog-to-digital converters (ADCs) causes the transducer voltage to collapse due to circuit loading. Inserting a voltage follower buffers the sensor, drawing virtually zero current while driving downstream avionics buses with robust current capability.

The Summing Amplifier (Inverting Analog Adder)

The summing amplifier provides an analog output proportional to the inverted algebraic sum of multiple input control voltages. Multiple input signals ( V 1 , V 2 , V 3 , … V_1, V_2, V_3, \dots V 1 ​ , V 2 ​ , V 3 ​ , … ) are connected through individual input resistors ( R 1 , R 2 , R 3 , … R_1, R_2, R_3, \dots R 1 ​ , R 2 ​ , R 3 ​ , … ) to the op-amp's inverting virtual ground summing junction. V1 o----[ R1 ]----+

  • |
  • V2 o----[ R2 ]----+-----------[ Rf ]------------+
  • | |
  • V3 o----[ R3 ]----+ |\ |
  • +---| -\ |
  • | \ |
  • 0V --| + >--------------------+----o V_out
  • | /
  • |/
  • Mathematical Derivation via KCL

At the virtual ground node ( V − = 0 V V^- = 0\text{ V} V − = 0 V ), each input generates an independent input current: I 1 = V 1 R 1 , I 2 = V 2 R 2 , I 3 = V 3 R 3 I_1 = \frac{V_1}{R_1}, \quad I_2 = \frac{V_2}{R_2}, \quad I_3 = \frac{V_3}{R_3} I 1 ​ = R 1 ​ V 1 ​ ​ , I 2 ​ = R 2 ​ V 2 ​ ​ , I 3 ​ = R 3 ​ V 3 ​ ​

By Kirchhoff's Current Law at the summing node, the total current ( I t o t a l I_{total} I t o t a l ​ ) entering the junction must equal the current flowing across feedback resistor R f R_f R f ​ : I t o t a l = I 1 + I 2 + I 3 + ⋯ = I f I_{total} = I_1 + I_2 + I_3 + \dots = I_f I t o t a l ​ = I 1 ​ + I 2 ​ + I 3 ​ + ⋯ = I f ​ V 1 R 1 + V 2 R 2 + V 3 R 3 = − V o u t R f \frac{V_1}{R_1} + \frac{V_2}{R_2} + \frac{V_3}{R_3} = -\frac{V_{out}}{R_f} R 1 ​ V 1 ​ ​ + R 2 ​ V 2 ​ ​ + R 3 ​ V 3 ​ ​ = − R f ​ V o u t ​ ​

Solving for V o u t V_{out} V o u t ​ : V o u t = − ( R f R 1 V 1 + R f R 2 V 2 + R f R 3 V 3 ) V_{out} = -\left( \frac{R_f}{R_1}V_1 + \frac{R_f}{R_2}V_2 + \frac{R_f}{R_3}V_3 \right) V o u t ​ = − ( R 1 ​ R f ​ ​ V 1 ​ + R 2 ​ R f ​ ​ V 2 ​ + R 3 ​ R f ​ ​ V 3 ​ )

If all input resistors are chosen equal ( R 1 = R 2 = R 3 = R i n R_1 = R_2 = R_3 = R_{in} R 1 ​ = R 2 ​ = R 3 ​ = R in ​ ), the circuit acts as an equal-gain inverting adder: V o u t = − R f R i n ( V 1 + V 2 + V 3 ) V_{out} = -\frac{R_f}{R_{in}}(V_1 + V_2 + V_3) V o u t ​ = − R in ​ R f ​ ​ ( V 1 ​ + V 2 ​ + V 3 ​ )

Aviation Application: Flight Control Surface Mixing

In aircraft fly-by-wire and autopilot systems, summing amplifiers algebraically combine pilot control stick command voltages ( V pilot V_{\text{pilot}} V pilot ​ ), autopilot pitch displacement commands ( V AP V_{\text{AP}} V AP ​ ), and pitch-rate gyro damping feedback ( V gyro V_{\text{gyro}} V gyro ​ ) into a single command voltage sent to hydraulic elevator actuator servos.

The Differential Amplifier (Subtractor)

A differential amplifier amplifies the difference between two input signals while rejecting common-mode electrical interference present on both conductors: +------------[ Rf ]------------+

  • | |
  • V1 o----[ R1 ]--------+----| -\ |
  • | \ |
  • V2 o----[ R2 ]--------+----| + >--------------------+----o V_out
  • | | /
  • [R3] |/
  • |
  • GND

By applying superposition and the voltage divider equation at the non-inverting terminal ( V + = V 2 ⋅ R 3 R 2 + R 3 V^+ = V_2 \cdot \frac{R_3}{R_2 + R_3} V + = V 2 ​ ⋅ R 2 ​ + R 3 ​ R 3 ​ ​ ): V o u t = V 2 ( R 3 R 2 + R 3 ) ( 1 + R f R 1 ) − V 1 ( R f R 1 ) V_{out} = V_2 \left( \frac{R_3}{R_2 + R_3} \right) \left( 1 + \frac{R_f}{R_1} \right) - V_1 \left( \frac{R_f}{R_1} \right) V o u t ​ = V 2 ​ ( R 2 ​ + R 3 ​ R 3 ​ ​ ) ( 1 + R 1 ​ R f ​ ​ ) − V 1 ​ ( R 1 ​ R f ​ ​ )

When the resistor ratios are precisely balanced such that R f R 1 = R 3 R 2 \frac{R_f}{R_1} = \frac{R_3}{R_2} R 1 ​ R f ​ ​ = R 2 ​ R 3 ​ ​ (conventionally R 2 = R 1 R_2 = R_1 R 2 ​ = R 1 ​ and R 3 = R f R_3 = R_f R 3 ​ = R f ​ ): V o u t = R f R 1 ( V 2 − V 1 ) V_{out} = \frac{R_f}{R_1}(V_2 - V_1) V o u t ​ = R 1 ​ R f ​ ​ ( V 2 ​ − V 1 ​ )

The Three-Op-Amp Instrumentation Amplifier

While the single op-amp differential circuit functions well, its input impedance is limited to R 1 R_1 R 1 ​ and R 2 R_2 R 2 ​ , which can unbalance bridge circuits. In critical flight-test instrumentation (such as wing strain-gauge bridges and thermocouple exhaust gas temperature sensors), the three-op-amp instrumentation amplifier is standard. It places two non-inverting buffers ahead of the differential stage, providing gigohm input impedances on both lines and allowing voltage gain to be adjusted using a single external gain resistor ( R G R_G R G ​ ): A v = ( 1 + 2 R R G ) ( R f R 1 ) A_v = \left( 1 + \frac{2R}{R_G} \right) \left( \frac{R_f}{R_1} \right) A v ​ = ( 1 + R G ​ 2 R ​ ) ( R 1 ​ R f ​ ​ )

Linear Circuit Topologies Comparison

Configuration Voltage Gain ( A v A_v A v ​ ) Phase Shift Input Impedance ( Z i n Z_{in} Z in ​ ) Primary Aircraft Application

Inverting Amplifier − R f / R i n -R_f / R_{in} − R f ​ / R in ​ 180 ∘ 180^\circ 18 0 ∘ R i n R_{in} R in ​ (moderate) Audio phase inversion, signal scaling

Non-Inverting Amplifier 1 + ( R f / R 1 ) 1 + (R_f / R_1) 1 + ( R f ​ / R 1 ​ ) 0 ∘ 0^\circ 0 ∘ (in-phase) Extremely high ( > 10 12 Ω > 10^{12}\ \Omega > 1 0 12 Ω ) Sensor preamplifiers, DC level scaling

Voltage Follower + 1.0 +1.0 + 1.0 ( 0 dB 0\text{ dB} 0 dB ) 0 ∘ 0^\circ 0 ∘ (in-phase) Extremely high ( > 10 12 Ω > 10^{12}\ \Omega > 1 0 12 Ω ) High-impedance sensor isolation buffers

Summing Amplifier − ∑ ( R f / R n ) V n -\sum (R_f / R_n) V_n − ∑ ( R f ​ / R n ​ ) V n ​ 180 ∘ 180^\circ 18 0 ∘ R n R_n R n ​ per channel Autopilot flight control command mixing

Differential Amplifier ( R f / R 1 ) ( V 2 − V 1 ) (R_f / R_1)(V_2 - V_1) ( R f ​ / R 1 ​ ) ( V 2 ​ − V 1 ​ ) 0 ∘ 0^\circ 0 ∘ diff R 1 + R 2 R_1 + R_2 R 1 ​ + R 2 ​ Strain gauge bridges, thermocouple monitoring

Worked Numerical Calculation: Autopilot Elevator Command Mixer

An analog flight-control summing amplifier stage mixes pilot stick pitch command ( V 1 V_1 V 1 ​ ), autopilot pitch correction ( V 2 V_2 V 2 ​ ), and rate-gyro damping ( V 3 V_3 V 3 ​ ). The circuit is energized from dual ± 15.0 V DC \pm 15.0\text{ V DC} ± 15.0 V DC aircraft avionics power rails, with an output saturation limit of V s a t = ± 13.5 V V_{sat} = \pm 13.5\text{ V} V s a t ​ = ± 13.5 V .

Component parameters:

Feedback resistor: R f = 100 k Ω R_f = 100\text{ k}\Omega R f ​ = 100 k Ω

Channel 1 (Pilot): R 1 = 50 k Ω R_1 = 50\text{ k}\Omega R 1 ​ = 50 k Ω , V 1 = + 1.20 V V_1 = +1.20\text{ V} V 1 ​ = + 1.20 V

Channel 2 (Autopilot): R 2 = 100 k Ω R_2 = 100\text{ k}\Omega R 2 ​ = 100 k Ω , V 2 = − 0.80 V V_2 = -0.80\text{ V} V 2 ​ = − 0.80 V

Channel 3 (Rate Gyro): R 3 = 25 k Ω R_3 = 25\text{ k}\Omega R 3 ​ = 25 k Ω , V 3 = + 0.50 V V_3 = +0.50\text{ V} V 3 ​ = + 0.50 V V1 (+1.2V) o----[ 50k ]-----+

  • |
  • V2 (-0.8V) o----[ 100k ]----+-----------[ 100k ]----------+
  • | |
  • V3 (+0.5V) o----[ 25k ]-----+ |\ |
  • +---| -\ |
  • | \ |
  • 0V --| + >--------------------+----o V_out
  • | /
  • |/
  • Step 1: Calculate Individual Channel Gains

Channel 1 Gain: A v 1 = − R f R 1 = − 100 k Ω 50 k Ω = − 2.0 A_{v1} = -\frac{R_f}{R_1} = -\frac{100\text{ k}\Omega}{50\text{ k}\Omega} = -2.0 A v 1 ​ = − R 1 ​ R f ​ ​ = − 50 k Ω 100 k Ω ​ = − 2.0

Channel 2 Gain: A v 2 = − R f R 2 = − 100 k Ω 100 k Ω = − 1.0 A_{v2} = -\frac{R_f}{R_2} = -\frac{100\text{ k}\Omega}{100\text{ k}\Omega} = -1.0 A v 2 ​ = − R 2 ​ R f ​ ​ = − 100 k Ω 100 k Ω ​ = − 1.0

Channel 3 Gain: A v 3 = − R f R 3 = − 100 k Ω 25 k Ω = − 4.0 A_{v3} = -\frac{R_f}{R_3} = -\frac{100\text{ k}\Omega}{25\text{ k}\Omega} = -4.0 A v 3 ​ = − R 3 ​ R f ​ ​ = − 25 k Ω 100 k Ω ​ = − 4.0

Step 2: Calculate Individual Output Contributions

From Channel 1: V o u t 1 = A v 1 ⋅ V 1 = − 2.0 × ( + 1.20 V ) = − 2.40 V V_{out1} = A_{v1} \cdot V_1 = -2.0 \times (+1.20\text{ V}) = -2.40\text{ V} V o u t 1 ​ = A v 1 ​ ⋅ V 1 ​ = − 2.0 × ( + 1.20 V ) = − 2.40 V

From Channel 2: V o u t 2 = A v 2 ⋅ V 2 = − 1.0 × ( − 0.80 V ) = + 0.80 V V_{out2} = A_{v2} \cdot V_2 = -1.0 \times (-0.80\text{ V}) = +0.80\text{ V} V o u t 2 ​ = A v 2 ​ ⋅ V 2 ​ = − 1.0 × ( − 0.80 V ) = + 0.80 V

From Channel 3: V o u t 3 = A v 3 ⋅ V 3 = − 4.0 × ( + 0.50 V ) = − 2.00 V V_{out3} = A_{v3} \cdot V_3 = -4.0 \times (+0.50\text{ V}) = -2.00\text{ V} V o u t 3 ​ = A v 3 ​ ⋅ V 3 ​ = − 4.0 × ( + 0.50 V ) = − 2.00 V

Step 3: Compute Total Output Voltage ( V o u t V_{out} V o u t ​ ) V o u t = V o u t 1 + V o u t 2 + V o u t 3 = − 2.40 V + 0.80 V − 2.00 V = − 3.60 V V_{out} = V_{out1} + V_{out2} + V_{out3} = -2.40\text{ V} + 0.80\text{ V} - 2.00\text{ V} = -3.60\text{ V} V o u t ​ = V o u t 1 ​ + V o u t 2 ​ + V o u t 3 ​ = − 2.40 V + 0.80 V − 2.00 V = − 3.60 V

Step 4: Saturation Check

The resulting output of − 3.60 V -3.60\text{ V} − 3.60 V is well within the negative saturation rail of − 13.5 V -13.5\text{ V} − 13.5 V . Linear operation is maintained.

Warning

Rail Saturation Hazard: If pilot input increases to V 1 = + 6.0 V V_1 = +6.0\text{ V} V 1 ​ = + 6.0 V with other inputs unchanged, theoretical output would be V o u t = ( − 2.0 × 6.0 ) + 0.80 − 2.00 = − 13.20 V V_{out} = (-2.0 \times 6.0) + 0.80 - 2.00 = -13.20\text{ V} V o u t ​ = ( − 2.0 × 6.0 ) + 0.80 − 2.00 = − 13.20 V . Any further increase beyond + 6.15 V +6.15\text{ V} + 6.15 V drives the output against the negative saturation rail ( − 13.5 V -13.5\text{ V} − 13.5 V ), clipping the waveform and freezing servo control authority.

Loading diagram... Basic Linear Op-Amp Circuit Configurations