Study guide
3.2 Transistor Circuit Configurations
EASA Part-66 Module 04 — Electronic Fundamentals Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Semiconductor Physics & Diode Fundamentals
1.1 Semiconductor Theory, PN Junction & Conduction 1.2 Power Rectification & Filtering Circuits 1.3 Diode Wave-Shaping & Voltage Multipliers
2 Chapter 2: Special-Purpose Diodes & Semiconductor Testing
2.1 Voltage Regulation & Zener Diodes 2.2 Optoelectronic, Fast-Switching & Power Diodes 2.3 Diode Testing, Failure Modes & Aircraft Applications
3 Chapter 3: Transistor Principles, Configurations & Biasing
3.1 BJT Structure, Operation & Current Relationships 3.2 Transistor Circuit Configurations 3.3 Transistor Biasing, Thermal Stability & Testing
4 Chapter 4: Transistor Amplifiers, FETs & Oscillators
4.1 Amplifier Operating Classes & Push-Pull Systems 4.2 Multistage Coupling & Negative Feedback 4.3 Field Effect Transistors & Darlington Pairs 4.4 Oscillators & Multivibrators
5 Chapter 5: Operational Amplifiers & Linear Integrated Circuits
5.1 Op-Amp Fundamentals, Characteristics & Virtual Ground 5.2 Op-Amp Linear Circuits & Calculations 5.3 Active Wave-Shaping, Comparators & Digital Logic Basics
6 Chapter 6: Printed Circuit Boards & Electrostatic Discharge Protection
6.1 PCB Design, Layered Construction & Manufacturing 6.2 PCB Inspection, Soldering Defects & Electrostatic Discharge (ESD) Control
7 Chapter 7: Servomechanism Principles, Transducers & Control
7.1 Open-Loop and Closed-Loop Control Architecture 7.2 Servomechanism Transducers (Potentiometers, LVDTs & RVDTs) 7.3 Servo Dynamics, Damping, Motors & Hunting Prevention
8 Chapter 8: Synchro Systems, Resolvers & Fault Diagnosis
8.1 Torque Synchro Systems (TX, TR & Differentials) 8.2 Control Synchros, Resolvers & Inductive Sensors 8.3 Synchro Troubleshooting, Wiring Faults & Maintenance
3.2 Transistor Circuit Configurations
Key Takeaways Explain This Topic AI
A BJT can be connected in three fundamental circuit topologies: Common Emitter (CE), Common Base (CB), and Common Collector (CC / Emitter Follower), each offering distinct impedance and gain profiles.
The Common Emitter configuration is the only topology that introduces a 180° phase inversion between the input and output AC voltage waveforms, while delivering high voltage, current, and total power gains.
The Common Base configuration features very low input impedance (20 Ω to 50 Ω), very high output impedance (~1 MΩ), unity current gain (alpha < 1), and superior high-frequency bandwidth due to the total absence of Miller effect capacitance.
The Common Collector (Emitter Follower) features high input impedance (20 kΩ to 500 kΩ), very low output impedance (10 Ω to 100 Ω), and a voltage gain slightly below unity (Av ≈ 0.98 to 0.99), serving as the universal impedance-matching buffer in avionics.
Multistage avionics systems cascade these topologies strategically—often using a CC input stage for high-Z sensor loading, CE intermediate stages for voltage/power amplification, and CB or CC output stages for transmission line driving.
Last updated: September 2026
3.2 Transistor Circuit Configurations
Because a BJT has three terminals, one terminal must always be shared in common between the input and output circuits (often referenced to AC ground). This leads to the three fundamental BJT circuit configurations :
- Common Emitter (CE)
- Common Base (CB)
- Common Collector (CC) , universally known as the Emitter Follower
Each topology exhibits distinct characteristics regarding input impedance ( Z i n Z_{in} Z in ), output impedance ( Z o u t Z_{out} Z o u t ), voltage gain ( A v A_v A v ), current gain ( A i A_i A i ), and phase relationship ( Δ θ \Delta\theta Δ θ ), governing its role in avionics systems.
1. Common Emitter (CE) Configuration
In the Common Emitter topology, the AC input is applied to the Base , the output is extracted from the Collector , and the Emitter is shared in common (connected to AC ground via a bypass capacitor).
Key Characteristics
Input Impedance ( Z i n Z_{in} Z in ) : Moderate, typically 1 k Ω to 5 k Ω 1\text{ k}\Omega\text{ to }5\text{ k}\Omega 1 k Ω to 5 k Ω ( Z i n ≈ β ⋅ r e ′ Z_{in} \approx \beta \cdot r'_e Z in ≈ β ⋅ r e ′ ).
Output Impedance ( Z o u t Z_{out} Z o u t ) : Moderate to high, typically 20 k Ω to 100 k Ω 20\text{ k}\Omega\text{ to }100\text{ k}\Omega 20 k Ω to 100 k Ω (determined by R C ∥ r o R_C \parallel r_o R C ∥ r o ).
Voltage Gain ( A v A_v A v ) : High, typically − 50 to − 500 -50\text{ to }-500 − 50 to − 500 ( A v ≈ − R C / r e ′ A_v \approx -R_C / r'_e A v ≈ − R C / r e ′ ).
Current Gain ( A i A_i A i ) : High, equal to β \beta β ( 50 to 300 50\text{ to }300 50 to 300 ).
Power Gain ( A p A_p A p ) : Highest of all three configurations . Because A p = A v × A i A_p = A_v \times A_i A p = A v × A i , combining substantial voltage gain with high current gain produces power gains of 40 to 47 dB 40\text{ to }47\text{ dB} 40 to 47 dB .
Phase Shift : 180 ∘ 180^\circ 18 0 ∘ Phase Inversion between input and output AC voltages.
Mechanism of Phase Inversion
The 180 ∘ 180^\circ 18 0 ∘ phase inversion is a central EASA Part-66 exam concept:
When the input voltage at the base swings positive , forward bias V B E V_{BE} V BE increases.
Base current I B I_B I B increases, causing collector current I C = β I B I_C = \beta I_B I C = β I B to rise.
The increased I C I_C I C causes a larger voltage drop across collector resistor R C R_C R C ( V R C = I C R C V_{RC} = I_C R_C V RC = I C R C ).
Because collector voltage is V C = V C C − I C R C V_C = V_{CC} - I_C R_C V C = V CC − I C R C , the collector voltage drops toward ground.
Thus, a positive-going input peak produces a negative-going output peak , creating a 180 ∘ 180^\circ 18 0 ∘ phase inversion.
Warning
Multistage Feedback Hazards : In aircraft autopilot servos and interphone amplifiers, cascading two CE stages creates two sequential 180 ∘ 180^\circ 18 0 ∘ shifts ( 180 ∘ + 180 ∘ = 360 ∘ = 0 ∘ 180^\circ + 180^\circ = 360^\circ = 0^\circ 18 0 ∘ + 18 0 ∘ = 36 0 ∘ = 0 ∘ ). If stray capacitive coupling feeds output signal back to the input in phase, it produces regenerative positive feedback , causing unwanted high-frequency oscillation.
2. Common Base (CB) Configuration
In the Common Base topology, the AC input is injected into the Emitter , the output is taken from the Collector , and the Base is connected directly to AC ground.
Key Characteristics
Input Impedance ( Z i n Z_{in} Z in ) : Very low, typically 20 Ω to 50 Ω 20\ \Omega\text{ to }50\ \Omega 20 Ω to 50 Ω ( Z i n ≈ r e ′ = 25 mV / I E Z_{in} \approx r'_e = 25\text{ mV} / I_E Z in ≈ r e ′ = 25 mV / I E ).
Output Impedance ( Z o u t Z_{out} Z o u t ) : Very high, typically 500 k Ω to 1 M Ω 500\text{ k}\Omega\text{ to }1\text{ M}\Omega 500 k Ω to 1 M Ω .
Voltage Gain ( A v A_v A v ) : High, comparable to Common Emitter ( A v ≈ + R C / r e ′ A_v \approx +R_C / r'_e A v ≈ + R C / r e ′ ).
Current Gain ( A i A_i A i ) : Slightly less than unity ( A i = α ≈ 0.95 to 0.998 A_i = \alpha \approx 0.95\text{ to }0.998 A i = α ≈ 0.95 to 0.998 ). There is no current gain .
Power Gain ( A p A_p A p ) : Moderate ( A p = A v × α A_p = A_v \times \alpha A p = A v × α ).
Phase Shift : 0 ∘ 0^\circ 0 ∘ (Non-inverting / In-Phase) .
Miller Effect Suppression & RF Applications
In Common Emitter amplifiers, collector-base capacitance ( C c b C_{cb} C c b ) is amplified by voltage gain ( C M i l l e r = C c b ( 1 + ∣ A v ∣ ) C_{Miller} = C_{cb}(1 + |A_v|) C M i ll er = C c b ( 1 + ∣ A v ∣ ) ), creating high-frequency feedback that degrades bandwidth.
In the Common Base configuration, the base is tied to AC ground, acting as an electrostatic shield between emitter and collector. This eliminates Miller multiplication of capacitance. Consequently, CB stages provide superior high-frequency bandwidth and stability, making them the standard choice for aircraft VHF/UHF communications front-ends , radar IF preamplifiers, and matching to 50 Ω 50\ \Omega 50 Ω antenna feedlines.
3. Common Collector (CC) / Emitter Follower
In the Common Collector topology, the AC input is applied to the Base , the output is taken from the Emitter , and the Collector is tied to AC ground (via the DC supply rail V C C V_{CC} V CC ).
Key Characteristics
Input Impedance ( Z i n Z_{in} Z in ) : High, typically 20 k Ω to 500 k Ω 20\text{ k}\Omega\text{ to }500\text{ k}\Omega 20 k Ω to 500 k Ω ( Z i n ≈ β R E Z_{in} \approx \beta R_E Z in ≈ β R E ).
Output Impedance ( Z o u t Z_{out} Z o u t ) : Very low, typically 10 Ω to 100 Ω 10\ \Omega\text{ to }100\ \Omega 10 Ω to 100 Ω ( Z o u t ≈ r e ′ + [ R S / β ] Z_{out} \approx r'_e + [R_S / \beta] Z o u t ≈ r e ′ + [ R S / β ] ).
Voltage Gain ( A v A_v A v ) : Slightly less than unity, typically 0.98 to 0.99 0.98\text{ to }0.99 0.98 to 0.99 (never exceeds 1.0).
Current Gain ( A i A_i A i ) : High, equal to β + 1 \beta + 1 β + 1 .
Power Gain ( A p A_p A p ) : Moderate ( A p ≈ A i A_p \approx A_i A p ≈ A i ).
Phase Shift : 0 ∘ 0^\circ 0 ∘ (Non-inverting / In-Phase) .
The Emitter Follower in Avionics
The circuit is known as the Emitter Follower because the emitter output voltage directly "follows" the base input voltage, offset only by the constant 0.7 V 0.7\text{ V} 0.7 V base-emitter diode drop: V E = V B − 0.7 V V_E = V_B - 0.7\text{ V} V E = V B − 0.7 V
Because it transforms high impedance to low impedance with unity voltage gain, the Common Collector is universally used as an impedance-matching buffer . It interfaces delicate, high-impedance sensors (such as piezoelectric engine vibration pickups and cockpit microphones) to low-impedance cables and downstream processing stages without signal loading or attenuation.
Summary Comparison Matrix
The table below summarizes the core parameters tested in EASA Part-66 Module 04:
- Parameter Common Emitter (CE) Common Base (CB) Common Collector (CC / Emitter Follower)
- Input Port Base Emitter Base
- Output Port Collector Collector Emitter
- Common Terminal Emitter Base Collector
Input Impedance ( Z i n Z_{in} Z in ) Moderate ( 1 − 5 k Ω 1 - 5\text{ k}\Omega 1 − 5 k Ω ) Very Low ( 20 − 50 Ω 20 - 50\ \Omega 20 − 50 Ω ) High ( 20 − 500 k Ω 20 - 500\text{ k}\Omega 20 − 500 k Ω )
Output Impedance ( Z o u t Z_{out} Z o u t ) Moderate-High ( 20 − 100 k Ω 20 - 100\text{ k}\Omega 20 − 100 k Ω ) Very High ( 500 k Ω − 1 M Ω 500\text{ k}\Omega - 1\text{ M}\Omega 500 k Ω − 1 M Ω ) Very Low ( 10 − 100 Ω 10 - 100\ \Omega 10 − 100 Ω )
Voltage Gain ( A v A_v A v ) High ( 50 − 500 50 - 500 50 − 500 ) High ( 50 − 500 50 - 500 50 − 500 ) Less than unity ( 0.98 − 0.99 0.98 - 0.99 0.98 − 0.99 )
Current Gain ( A i A_i A i ) High ( β ≈ 50 − 300 \beta \approx 50 - 300 β ≈ 50 − 300 ) Less than unity ( α < 1 \alpha < 1 α < 1 ) High ( β + 1 \beta + 1 β + 1 )
Power Gain ( A p A_p A p ) Highest ( A v × A i A_v \times A_i A v × A i ) Moderate Moderate
Phase Shift ( Δ θ \Delta\theta Δ θ ) 180 ∘ 180^\circ 18 0 ∘ (Inverting) 0 ∘ 0^\circ 0 ∘ (In-phase) 0 ∘ 0^\circ 0 ∘ (In-phase)
Typical Avionics Use General-purpose audio, IF, and power amplification VHF/UHF RF receivers, 50 Ω 50\ \Omega 50 Ω antenna line receivers Sensor buffer amplifiers, line drivers, impedance matchers
Note
Cascaded Architectures : Typical aircraft radar and communications receivers cascade these stages: a Common Base or Common Collector input stage matches antenna or sensor impedance, followed by multiple Common Emitter stages for high voltage and power amplification, terminating in an Emitter Follower output stage to drive transmission lines.