Study guide
2.2 Digital-to-Analogue Converters
EASA Part-66 Module 05 — Digital Techniques / Electronic Instrument Systems Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Numbering Systems
1.1 Numbering Systems: Decimal, Binary, Octal and Hexadecimal 1.2 Binary Arithmetic and Signed Number Representation 1.3 Binary Coded Decimal, Gray Code and Alphanumeric Codes
2 Chapter 2: Data Conversion
2.1 Analogue and Digital Signals, Sampling and Quantisation 2.2 Digital-to-Analogue Converters 2.3 Analogue-to-Digital Converters
3 Chapter 3: ARINC 429 Data Buses
3.1 ARINC 429 Specification, Physical Layer and Topology 3.2 ARINC 429 32-Bit Word Architecture 3.3 ARINC 429 Transmission, Timing and Troubleshooting
4 Chapter 4: Advanced Avionics Data Buses and Aircraft Ethernet
4.1 ARINC 629 Digital Autonomous Terminal Access 4.2 MIL-STD-1553B Military Avionics Data Bus 4.3 AFDX / ARINC 664 Part 7 Avionics Full-Duplex Switched Ethernet
5 Chapter 5: Combinational Logic Gates and Boolean Algebra
5.1 Basic Logic Gates, Truth Tables and Logic Levels 5.2 Boolean Algebra, De Morgan Theorems and Logic Simplification 5.3 Universal Gates and Aircraft Combinational Applications
6 Chapter 6: Sequential Logic, Registers and Logic Diagrams
6.1 Bistable Multivibrators: SR, JK, D and T Flip-Flops 6.2 Shift Registers and Data Storage Elements 6.3 Asynchronous and Synchronous Counters and Logic-Diagram Interpretation
7 Chapter 7: Computer Structure and Microprocessors
7.1 Computer Architecture, Terminology and the Bus System 7.2 Semiconductor Memory Technologies 7.3 Microprocessor Operation, Instruction Cycles and I/O
8 Chapter 8: Integrated Circuits, Multiplexing and Integrated Modular Avionics
8.1 Integrated Circuit Technology, Encoders, Decoders and Scale of Integration 8.2 Multiplexing and Demultiplexing Techniques 8.3 Remote Data Concentrators and Integrated Modular Avionics
9 Chapter 9: Fibre Optics in Aviation
9.1 Physics of Light Transmission and Optical Fibres 9.2 Fibre Cable Types, Signal Degradation and Optical Components 9.3 Fibre Optic Maintenance, Termination, Splicing and Inspection
10 Chapter 10: Electronic Displays and Flight Instrument Layout
10.1 Display Technologies: CRT, LED and LCD 10.2 Electronic Flight Instrument System Architecture 10.3 Cockpit Symbology, Colour Standards and Display Reversion
11 Chapter 11: Electrostatic Sensitive Devices
11.1 Physics of Electrostatic Charge and Device Susceptibility 11.2 ESDS Damage Mechanisms: Catastrophic versus Latent Failures 11.3 ESDS Handling, Storage, Packaging and Workshop Procedures
12 Chapter 12: Software Management Control and Airworthiness
12.1 Aviation Software Classification and RTCA DO-178C / EUROCAE ED-12C 12.2 Software Configuration Management and Part Numbering 12.3 Data Loading, Integrity Verification and Unapproved Changes
13 Chapter 13: Electromagnetic Environment
13.1 Electromagnetic Interference and Compatibility 13.2 High Intensity Radiated Fields and RF Hazards 13.3 Lightning Protection, Bonding and Static Dischargers
14 Chapter 14: Engine Indication, Warning and Monitoring Systems
14.1 Airbus ECAM — Electronic Centralised Aircraft Monitoring 14.2 Boeing EICAS — Engine Indicating and Crew Alerting System 14.3 Comparison, Failure Reversion and Sensor Interfacing
15 Chapter 15: Flight Management, Navigation and Surveillance Systems
15.1 Flight Management System and Control Display Unit 15.2 Inertial Reference, AHRS/ADIRU Context and GPS 15.3 Traffic Collision Avoidance and Terrain Awareness
16 Chapter 16: Fly-By-Wire, BITE, ACARS, Cabin and Information Systems
16.1 Fly-By-Wire Flight Control 16.2 Built-In Test Equipment and Central Maintenance Computers 16.3 ACARS, Cabin Systems and Information Systems
2.2 Digital-to-Analogue Converters
Key Takeaways Explain This Topic AI
A digital-to-analogue converter reconstructs a voltage or current from an n-bit word; the ideal analogue step is the reference span divided by 2^n, matching the resolution discussed for quantisers.
Binary-weighted resistor networks need a wide spread of precision resistances, whereas an R-2R ladder uses only two resistance values and is the usual integrated-circuit architecture.
Settling time is the interval required for the analogue output to enter and remain within a specified error band, commonly plus or minus one-half LSB, after a code change.
Monotonicity means the analogue output never decreases when the digital input increases by one LSB; missing steps and large differential non-linearity destroy monotonicity.
Offset error, gain error, reference drift, and glitches are the principal limitations when digital boxes drive display brightness, servo commands, or analogue cockpit instruments.
Last updated: September 2026
2.2 Digital-to-Analogue Converters
Digital computers command many analogue actuators and indicators. A display computer may set backlight brightness with a voltage. A flight-control or autopilot computer may send an analogue rate or position command to a servo amplifier that still expects a smooth voltage. Some standby or repeater instruments remain analogue even though the source parameter now lives in a digital air-data or inertial box. The current topic 5.3 heading and levels are broad. The pre-12 June 2024 detailed description identified digital-to-analogue converter (DAC) operation, inputs, outputs, applications, and limitations; this guide retains that useful scope. Category B2 knowledge is level 2; Category B1 is level 1.
A DAC accepts an n n n -bit digital word and a stable analogue reference . It produces a voltage or a current that, in the ideal case, is V out = V ref × D 2 n V_{\text{out}} = V_{\text{ref}} \times \frac{D}{2^n} V out = V ref × 2 n D
for a unipolar straight-binary code D D D running from 0 0 0 to 2 n − 1 2^n-1 2 n − 1 . (Some avionics DACs use bipolar offset-binary or two’s-complement coding so that mid-scale is zero volts; the arithmetic changes but the hardware ideas do not.) The analogue resolution is again one LSB, V ref / 2 n V_{\text{ref}}/2^n V ref / 2 n (unipolar). The digital input is the only “sensor” the DAC has: garbage codes, stuck bits, or a collapsed reference produce a wrong analogue command even when the processor logic looks healthy on a bus analyser.
Binary-Weighted Resistor DACs
The classical weighted-resistor (or binary-weighted) DAC uses a resistor for each bit whose conductance is proportional to that bit’s binary weight. For a 4-bit example the resistors are R R R , 2 R 2R 2 R , 4 R 4R 4 R , and 8 R 8R 8 R (or the current-defining set R / 8 R/8 R /8 , R / 4 R/4 R /4 , R / 2 R/2 R /2 , R R R ). Each bit switch connects its resistor either to the reference or to analogue ground. The weighted currents (or voltages) are summed, usually at the inverting node of an operational amplifier.
The architecture is easy to draw and easy to explain in an oral board, which is why it still appears in basic-knowledge teaching. It is much harder to manufacture at 12 bits and beyond. An 8-bit weighted network already needs a resistance ratio of 128 : 1 128:1 128 : 1 between the most-significant and least-significant bit. Those resistors must track over the full airborne temperature range, or the bit weights cease to be binary. A single out-of-tolerance most-significant-bit resistor can create a large differential non-linearity (DNL) error — a jump that is much larger or much smaller than one LSB — and can destroy monotonicity .
Switch on-resistance adds another error. The most-significant-bit switch carries the largest current, so a few ohms of MOSFET resistance steal a significant fraction of that bit’s weight unless the design uses force-sense switching or very large devices. For these reasons, discrete weighted-resistor DACs are rare in modern line-replaceable units except in low-resolution, non-critical analogue trims.
R-2R Ladder DACs
The R-2R ladder uses only two resistance values, R R R and 2 R 2R 2 R , arranged so that each bit node sees the same equivalent resistance looking downstream. A bit switch steers the node current either to the summing amplifier or to ground (current-mode ladder) or switches the node between V ref V_{\text{ref}} V ref and ground (voltage-mode ladder). Because every rung is R R R or 2 R 2R 2 R , integrated-circuit processes can match the ratio tightly. A 12-bit monolithic DAC is therefore almost always an R-2R ladder or a segmented variant of the same idea, not a 12-resistor binary-weighted string stretching from R R R to 2048 R 2048R 2048 R .
Current-mode ladders are fast: the switch nodes sit at a virtual earth and the parasitic capacitances do not have to slew through large voltages. Voltage-mode ladders can be simpler when a buffered voltage output is required and speed is modest. In either case the reference must be quieter and more stable than one LSB if the analogue command is to remain inside its error budget. Reference drift with temperature appears as a gain error that scales every code, including full-scale brightness or full-scale servo demand.
Current Output versus Voltage Output
Many DAC integrated circuits are current-output devices. The ladder (or a set of weighted current sources) delivers I out I_{\text{out}} I out into a virtual-earth summing node. An external or on-chip transimpedance amplifier converts that current to a voltage, V out = − I out R F V_{\text{out}} = -I_{\text{out}} R_F V out = − I out R F . The feedback resistor and the amplifier’s settling behaviour then become part of the converter’s analogue specification. A technician probing the DAC pin may see a current, not a voltage; the “DAC output” the servo actually uses is after the amplifier.
Voltage-output DACs include the buffer. They are convenient for driving high-impedance loads such as display dimming inputs or analogue meter movements through a further isolation stage. They are less convenient for driving low-impedance loads or long screened cables: the buffer must supply current, reject the cable capacitance, and still settle inside the LSB band. In either style the DAC does not create energy from the digital word. The analogue power comes from the reference and the supply rails. A collapsing 5 V 5\text{ V} 5 V analogue rail will pull every brightness and servo command toward the wrong end-stop even if the digital data bus remains perfect.
Settling Time, Glitches and Monotonicity
Settling time is the interval from a digital code change until the analogue output enters and remains inside a specified error band, commonly ± 1 2 LSB \pm \tfrac{1}{2}\text{ LSB} ± 2 1 LSB (sometimes ± 1 LSB \pm 1\text{ LSB} ± 1 LSB on slower parts). Major-carry transitions — for example 01111111 01111111 01111111 to 10000000 10000000 10000000 — are the worst case, because every bit switch changes at once. During that instant the output can show a narrow glitch : a spike caused by unequal switch timing. A following analogue filter or a deglitching sample-and-hold is often used when the DAC drives a servo that would otherwise twitch.
Monotonicity means that if the digital input increases by one LSB, the analogue output does not decrease. A monotonic 12-bit DAC may still have DNL errors smaller than one LSB; it will never reverse direction on a rising ramp of codes. A non-monotonic DAC can make a closed-loop servo hunt or an analogue pointer jump backward as the computed parameter increases. Integral non-linearity (INL) describes the bow of the transfer curve relative to the ideal end-point or best-fit line; large INL is an accuracy problem even when the converter remains monotonic.
Offset Error, Gain Error and Other Limitations
Offset error is the analogue output when the digital input is the zero code (or the bipolar mid-scale code). It shifts every point on the transfer curve by the same voltage. Gain error is the error in the slope: full-scale output is not exactly V ref × ( 2 n − 1 ) / 2 n V_{\text{ref}}\times(2^n-1)/2^n V ref × ( 2 n − 1 ) / 2 n . In service, offset often tracks input-amplifier or buffer drift; gain often tracks the reference. Neither error is cured by “more bits” if the analogue reference has moved.
Other practical limitations that Module 05 expects you to name:
Resolution versus accuracy , exactly as in Section 2.1: a 16-bit DAC can still be inaccurate.
Temperature coefficients of the reference, the ladder, and the output amplifier.
Supply rejection : ripple on analogue rails appears on V out V_{\text{out}} V out .
Digital feedthrough and clock noise on the analogue pin.
Load regulation and the inability of a voltage DAC to drive a heavy analogue meter without a buffer.
Code-dependent output impedance on unbuffered current-output pins.
Property Binary-weighted resistor DAC R-2R ladder DAC
Resistance values R , 2 R , 4 R , … , 2 n − 1 R R, 2R, 4R, \ldots, 2^{n-1}R R , 2 R , 4 R , … , 2 n − 1 R Only R R R and 2 R 2R 2 R
- Matching difficulty Rises rapidly with n n n Two values; suited to monolithic processes
- Typical resolution in LRUs Low (trim, simple analogue) 8 to 16 bits common
- Dominant errors MSB resistor and switch resistance Reference, switch timing, ladder ratio
- Output form Usually voltage via summing amplifier Current or voltage, often current-mode
- Speed Limited by large MSB time constants Fast in current mode; buffer may dominate
- Monotonicity risk High if MSB weight is wrong Designed in if DNL stays above − 1 LSB -1\text{ LSB} − 1 LSB
- Aircraft Applications
Display brightness and flooding. Electronic flight instrument and crew-alerting displays need analogue lamp or backlight drive that follows a digital dimming word from the display computer or a lighting-control panel. The DAC output is usually a voltage or a low-frequency pulse-width command reconstructed to analogue. Settling time matters when the crew selects a new lighting preset; a slow or ringing DAC is seen as flicker. Offset error appears as a residual glow at the “off” code; gain error appears as a display that will not reach full day brightness.
Servo and actuator commands. Many autopilot, yaw-damper, and engine-control interfaces still present an analogue voltage or current to a servo amplifier even though the control law is digital. The DAC is then inside the command path. Non-monotonicity or large glitches can be interpreted as a command reversal. Conversion must settle inside the servo’s inner-loop sample time. Technicians tracing a “digital box, analogue jack” interface should measure the analogue command with the digital word known from BITE, not assume the pin voltage is a raw sensor.
Analogue cockpit instruments driven from digital boxes. Repeater altimeters, analogue standby interfaces, and older engine gauges may be driven from a digital air-data or engine computer through a DAC (or through a synchro/resolver wrapper that itself contains conversion). The limitation set is the same: reference integrity, monotonicity, settling, and the analogue cable. A digital parameter that is correct on the bus can still drive a wrong analogue pointer if the DAC reference or the instrument buffer has failed.
Worked Numerical Example: 8-bit Brightness DAC
A unipolar voltage-output DAC sets display backlight command from 0 V 0\text{ V} 0 V to a 5.000 V 5.000\text{ V} 5.000 V reference. The digital word is 8 bits.
Step 1 — Resolution V LSB = 5.000 V 256 = 19.53 mV V_{\text{LSB}} = \frac{5.000\text{ V}}{256} = 19.53\text{ mV} V LSB = 256 5.000 V = 19.53 mV
Step 2 — Ideal output for code D = 200 D = 200 D = 200 V out = 5.000 V × 200 256 = 3.906 V V_{\text{out}} = 5.000\text{ V} \times \frac{200}{256} = 3.906\text{ V} V out = 5.000 V × 256 200 = 3.906 V
Step 3 — Offset and gain
If the measured output at code 0 0 0 is + 15 mV +15\text{ mV} + 15 mV , the offset error is + 15 mV +15\text{ mV} + 15 mV (less than one LSB). If the measured full-scale code 255 255 255 is 4.900 V 4.900\text{ V} 4.900 V instead of 5.000 × 255 / 256 = 4.980 V 5.000\times 255/256 = 4.980\text{ V} 5.000 × 255/256 = 4.980 V , there is a gain error of about − 80 mV -80\text{ mV} − 80 mV at the top of the scale. The display will never reach the intended day brightness until the reference or the gain path is corrected.
Step 4 — Settling
If the servo or lighting amplifier requires the analogue voltage to be inside ± 1 2 LSB \pm \tfrac{1}{2}\text{ LSB} ± 2 1 LSB ( ± 9.8 mV \pm 9.8\text{ mV} ± 9.8 mV ) within 20 μ s 20\text{ }\mu\text{s} 20 μ s , a DAC whose datasheet settling time is 50 μ s 50\text{ }\mu\text{s} 50 μ s is the wrong part, regardless of its 8-bit resolution.
Note
Inputs, outputs, and limitations belong in the same breath. The input is the digital word plus the analogue reference and supplies. The output is a voltage or a current that must be buffered for the real load. The limitations — settling, monotonicity, offset, gain, glitch, temperature, and load — decide whether that pin is fit to drive a brightness input, a servo, or an analogue instrument.