Study guide
2.1 Analogue and Digital Signals, Sampling and Quantisation
EASA Part-66 Module 05 — Digital Techniques / Electronic Instrument Systems Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Numbering Systems
1.1 Numbering Systems: Decimal, Binary, Octal and Hexadecimal 1.2 Binary Arithmetic and Signed Number Representation 1.3 Binary Coded Decimal, Gray Code and Alphanumeric Codes
2 Chapter 2: Data Conversion
2.1 Analogue and Digital Signals, Sampling and Quantisation 2.2 Digital-to-Analogue Converters 2.3 Analogue-to-Digital Converters
3 Chapter 3: ARINC 429 Data Buses
3.1 ARINC 429 Specification, Physical Layer and Topology 3.2 ARINC 429 32-Bit Word Architecture 3.3 ARINC 429 Transmission, Timing and Troubleshooting
4 Chapter 4: Advanced Avionics Data Buses and Aircraft Ethernet
4.1 ARINC 629 Digital Autonomous Terminal Access 4.2 MIL-STD-1553B Military Avionics Data Bus 4.3 AFDX / ARINC 664 Part 7 Avionics Full-Duplex Switched Ethernet
5 Chapter 5: Combinational Logic Gates and Boolean Algebra
5.1 Basic Logic Gates, Truth Tables and Logic Levels 5.2 Boolean Algebra, De Morgan Theorems and Logic Simplification 5.3 Universal Gates and Aircraft Combinational Applications
6 Chapter 6: Sequential Logic, Registers and Logic Diagrams
6.1 Bistable Multivibrators: SR, JK, D and T Flip-Flops 6.2 Shift Registers and Data Storage Elements 6.3 Asynchronous and Synchronous Counters and Logic-Diagram Interpretation
7 Chapter 7: Computer Structure and Microprocessors
7.1 Computer Architecture, Terminology and the Bus System 7.2 Semiconductor Memory Technologies 7.3 Microprocessor Operation, Instruction Cycles and I/O
8 Chapter 8: Integrated Circuits, Multiplexing and Integrated Modular Avionics
8.1 Integrated Circuit Technology, Encoders, Decoders and Scale of Integration 8.2 Multiplexing and Demultiplexing Techniques 8.3 Remote Data Concentrators and Integrated Modular Avionics
9 Chapter 9: Fibre Optics in Aviation
9.1 Physics of Light Transmission and Optical Fibres 9.2 Fibre Cable Types, Signal Degradation and Optical Components 9.3 Fibre Optic Maintenance, Termination, Splicing and Inspection
10 Chapter 10: Electronic Displays and Flight Instrument Layout
10.1 Display Technologies: CRT, LED and LCD 10.2 Electronic Flight Instrument System Architecture 10.3 Cockpit Symbology, Colour Standards and Display Reversion
11 Chapter 11: Electrostatic Sensitive Devices
11.1 Physics of Electrostatic Charge and Device Susceptibility 11.2 ESDS Damage Mechanisms: Catastrophic versus Latent Failures 11.3 ESDS Handling, Storage, Packaging and Workshop Procedures
12 Chapter 12: Software Management Control and Airworthiness
12.1 Aviation Software Classification and RTCA DO-178C / EUROCAE ED-12C 12.2 Software Configuration Management and Part Numbering 12.3 Data Loading, Integrity Verification and Unapproved Changes
13 Chapter 13: Electromagnetic Environment
13.1 Electromagnetic Interference and Compatibility 13.2 High Intensity Radiated Fields and RF Hazards 13.3 Lightning Protection, Bonding and Static Dischargers
14 Chapter 14: Engine Indication, Warning and Monitoring Systems
14.1 Airbus ECAM — Electronic Centralised Aircraft Monitoring 14.2 Boeing EICAS — Engine Indicating and Crew Alerting System 14.3 Comparison, Failure Reversion and Sensor Interfacing
15 Chapter 15: Flight Management, Navigation and Surveillance Systems
15.1 Flight Management System and Control Display Unit 15.2 Inertial Reference, AHRS/ADIRU Context and GPS 15.3 Traffic Collision Avoidance and Terrain Awareness
16 Chapter 16: Fly-By-Wire, BITE, ACARS, Cabin and Information Systems
16.1 Fly-By-Wire Flight Control 16.2 Built-In Test Equipment and Central Maintenance Computers 16.3 ACARS, Cabin Systems and Information Systems
2.1 Analogue and Digital Signals, Sampling and Quantisation
Key Takeaways Explain This Topic AI
Analogue aircraft signals are continuous in time and amplitude, whereas digital data exist only at sampling instants and only at a finite set of amplitude levels.
The Nyquist criterion requires the sampling frequency to exceed twice the highest frequency component of interest; otherwise high-frequency energy folds back as indistinguishable aliases.
An analogue anti-alias low-pass filter must precede the sample-and-hold, because a digital filter cannot remove aliases that have already been created at the sampler.
An n-bit quantiser provides 2^n discrete levels; the least-significant-bit step is the full-scale range divided by 2^n, and the maximum quantisation error is plus or minus one-half of that step.
Air-data pressures, LVDT and RVDT position voltages, and temperature-probe signals all enter analogue-to-digital converters after conditioning; resolution, sampling rate, and anti-alias filtering jointly set the usable digital word.
Last updated: September 2026
2.1 Analogue and Digital Signals, Sampling and Quantisation
Aircraft sensors produce physical quantities that vary smoothly: pitot and static pressure, total air temperature, and the analogue voltages from linear and rotary variable differential transformers (LVDTs and RVDTs) that report flight-control surface or actuator position. Digital computers, electronic instrument systems, and aircraft data buses cannot store those continuous waveforms as analogue voltages. They store binary words. Commission Implementing Regulation (EU) 2023/989 sets topic 5.3, Data conversion, at level 2 for B2/B2L and level 1 for B1. Its current Appendix I does not spell out the component concepts; the former detailed Appendix I description supplied analogue data, digital data, and converter operation, which this guide retains as historical study scope. This section develops the continuous-versus-discrete distinction, the sampling theorem, aliasing, quantisation, and the anti-alias filters that protect air-data and engine-sensor chains.
Continuous Analogue Data versus Discrete Digital Data
An analogue signal is continuous in both time and amplitude. At every instant the instantaneous value may occupy any real number within the transducer range. A platinum resistance temperature detector, a capacitive fuel-quantity probe, and an LVDT secondary voltage are analogue sources: their outputs change smoothly as temperature, fuel height, or ram displacement change. There is no inherent “step” in a correctly functioning analogue chain until a later converter imposes one.
A digital representation is discrete in time and discrete in amplitude. Time is sliced into sampling instants separated by the sampling period T s = 1 / f s T_s = 1/f_s T s = 1/ f s . Amplitude is restricted to a finite set of allowed levels. Between samples the digital system holds a number, not the original waveform. Once quantised, the sample is encoded as a binary word of n n n bits and may be transmitted on a digital bus or processed by a flight-guidance or engine computer.
The two domains are complementary rather than competing. Analogue circuits remain the natural interface to physics. Digital processing gives noise immunity on multi-receiver buses, exact repeatability of computed parameters, and straightforward Built-In Test Equipment (BITE) patterns. Every modern air-data computer, full-authority digital engine-control (FADEC) channel, and electronic flight instrument computer therefore contains an analogue front end, a sampler, a quantiser, and a digital processor. A technician who treats “digital” as automatically more accurate than “analogue” will misdiagnose offset, aliasing, and reference errors that originate entirely in the analogue path.
Sampling Rate and the Sampling Period
Sampling measures the analogue waveform at discrete instants and, with a sample-and-hold, freezes that voltage while the analogue-to-digital converter finishes conversion. The sampling frequency f s f_s f s must be chosen from the highest frequency of interest in the sensor bandwidth, not from a convenient leftover clock divider.
If a total-air-temperature signal is known to change no faster than a few hertz after probe thermal lag, a few tens of samples per second can capture the useful information. If a wide-band vibration accelerometer on an engine gearbox carries energy to several kilohertz, f s f_s f s must sit well above that band. Undersampling a fast signal is not a mild accuracy loss; it creates a false low-frequency image that the rest of the avionics will treat as a valid parameter.
The sampling period and the converter’s conversion time must also fit together. If conversion occupies most of T s T_s T s , the analogue value must already be held stable. That is why a sample-and-hold (treated in detail in Section 2.3) sits between the anti-alias filter and the quantiser on almost every aircraft data-acquisition channel.
The Nyquist Criterion
Harry Nyquist’s sampling theorem states that a band-limited signal containing no energy above f max f_{\max} f m a x can be reconstructed from uniformly spaced samples if f s > 2 f max f_s > 2 f_{\max} f s > 2 f m a x
The quantity 2 f max 2 f_{\max} 2 f m a x is the Nyquist rate . Half the sampling frequency, f s / 2 f_s/2 f s /2 , is the Nyquist frequency (also called the folding frequency). In some textbooks the inequality is written f s ≥ 2 f max f_s \ge 2 f_{\max} f s ≥ 2 f m a x ; practical avionics designs use a comfortable margin because real anti-alias filters do not cut off infinitely sharply and because reconstruction filters are not ideal brick walls.
A worked air-data illustration: suppose the highest useful frequency in a filtered pitot-static channel is 20 Hz 20\text{ Hz} 20 Hz . The theoretical minimum sampling rate is 40 samples/s 40\text{ samples/s} 40 samples/s . An air-data computer will typically sample far faster — often hundreds of hertz — so that digital filtering, BITE, and latency requirements are met and so that a practical analogue low-pass filter can begin rolling off well below f s / 2 f_s/2 f s /2 . The extra samples are not wasted; they buy filter transition-band width and reduce group-delay compromise.
Aliasing
When f s < 2 f max f_s < 2 f_{\max} f s < 2 f m a x , frequency components above the Nyquist frequency fold back into the baseband. A component at frequency f f f appears at f alias = ∣ f − k f s ∣ f_{\text{alias}} = \lvert f - k f_s \rvert f alias = ∣ f − k f s ∣
where the integer k k k is chosen so the result lies between 0 0 0 and f s / 2 f_s/2 f s /2 . The aliased tone is indistinguishable from a genuine low-frequency signal. No later digital filter can remove it, because the damage has already occurred at the sampling instant.
On an aircraft this is not an academic curiosity. Engine vibration, 400 Hz 400\text{ Hz} 400 Hz alternating-current ripple on a poorly filtered direct-current rail, and switching edges from nearby power electronics all inject energy above the intended sensor bandwidth. If that energy reaches the sampler, a slowly varying airspeed or temperature word can acquire a wandering error that looks like a valid aerodynamic or thermal change. A line-maintenance crew comparing a digital airspeed readout with a mechanical standby instrument may then chase the wrong unit.
Anti-Alias Filters
The only robust protection is an analogue anti-aliasing low-pass filter placed before the sample-and-hold. Its pass-band covers the frequencies the system must measure. Its stop-band has already attenuated everything above f s / 2 f_s/2 f s /2 to below one least-significant bit (or to a documented noise floor) before the sampling switch closes.
A single-pole RC filter rolls off at only 20 dB/decade 20\text{ dB/decade} 20 dB/decade , so the gap between f max f_{\max} f m a x and f s / 2 f_s/2 f s /2 must be wide, or a multi-pole active filter (Butterworth, Bessel, or elliptic) must be used. Bessel responses are favoured when waveform shape and group delay matter, as in some servo-command and vibration channels. After digitisation, additional digital low-pass filtering can refine the displayed or computed bandwidth, but it cannot repair aliases.
Warning
Do not omit or bypass the analogue anti-alias filter during troubleshooting. Substituting a raw sensor into a converter input “to see the true signal” can inject 400 Hz 400\text{ Hz} 400 Hz aircraft-bus ripple and high-frequency electromagnetic interference that alias into the displayed parameter. The indication then disagrees with a calibrated analogue gauge even though the digital box is working as designed.
Quantisation, Resolution and Bit Depth
After sampling, each held voltage is mapped onto the nearest of 2 n 2^n 2 n discrete levels. An n n n -bit converter therefore provides number of levels = 2 n \text{number of levels} = 2^n number of levels = 2 n
The quantisation step , or least-significant-bit (LSB) voltage, for a unipolar converter is V LSB = FSR 2 n V_{\text{LSB}} = \frac{\text{FSR}}{2^n} V LSB = 2 n FSR
where FSR is the full-scale range. A bipolar converter spanning ± V ref \pm V_{\text{ref}} ± V ref uses 2 V ref 2V_{\text{ref}} 2 V ref as the full-scale span. The table below lists the bit depths that appear constantly in Module 05 teaching and in aircraft data-acquisition hardware.
Bits n n n Levels 2 n 2^n 2 n LSB as a fraction of full-scale range LSB on a 10.00 V 10.00\text{ V} 10.00 V full-scale range
- 8 256 1 / 256 ≈ 0.391 % 1/256 \approx 0.391\% 1/256 ≈ 0.391% 39.1 mV 39.1\text{ mV} 39.1 mV
- 10 1 024 1 / 1 024 ≈ 0.0977 % 1/1\,024 \approx 0.0977\% 1/1 024 ≈ 0.0977% 9.77 mV 9.77\text{ mV} 9.77 mV
- 12 4 096 1 / 4 096 ≈ 0.0244 % 1/4\,096 \approx 0.0244\% 1/4 096 ≈ 0.0244% 2.44 mV 2.44\text{ mV} 2.44 mV
14 16 384 1 / 16 384 ≈ 0.0061 % 1/16\,384 \approx 0.0061\% 1/16 384 ≈ 0.0061% 610 μ V 610\text{ }\mu\text{V} 610 μ V
16 65 536 1 / 65 536 ≈ 0.0015 % 1/65\,536 \approx 0.0015\% 1/65 536 ≈ 0.0015% 153 μ V 153\text{ }\mu\text{V} 153 μ V
Quantisation Error and Quantisation Noise
Because the true analogue voltage may lie anywhere inside a step, the maximum quantisation error is ± 1 2 LSB \pm \tfrac{1}{2}\text{ LSB} ± 2 1 LSB . That error is not a random hardware fault; it is the irreducible price of representing a continuum with a finite code set. Over many samples of a busy signal the error behaves like additive noise — quantisation noise — with an RMS value of V LSB / 12 V_{\text{LSB}}/\sqrt{12} V LSB / 12 for an ideal uniform quantiser.
For a full-scale sine wave the theoretical signal-to-quantisation-noise ratio is approximately SQNR ≈ 6.02 n + 1.76 dB \text{SQNR} \approx 6.02n + 1.76\text{ dB} SQNR ≈ 6.02 n + 1.76 dB
Each extra bit therefore improves ideal SQNR by about 6 dB 6\text{ dB} 6 dB . Real converters fall short because of differential non-linearity, aperture jitter, and reference noise. Maintenance implications are direct: a 12-bit air-data channel cannot be turned into 16-bit performance by software scaling alone. The hardware resolution, the analogue front-end noise, and the anti-alias filter together set the usable precision.
Note
Resolution is not the same as accuracy. A 16-bit word can resolve 153 μ V 153\text{ }\mu\text{V} 153 μ V on a 10 V 10\text{ V} 10 V range and still be wrong by tens of millivolts if the voltage reference has drifted, the probe excitation is in error, or the analogue input amplifier has an offset. Resolution describes the fineness of the steps; accuracy describes closeness to the true physical quantity.
Aircraft Signal Paths into Converters
Typical analogue sources that enter analogue-to-digital converters on a transport aeroplane include:
Air-data sensors. Pitot and static pressures (often via vibrating-cylinder or solid-state transducers), angle-of-attack vanes, and total-air-temperature probes feed the air-data computer. After analogue conditioning they are sampled, quantised, and computed into computed airspeed, Mach number, pressure altitude, and true airspeed.
LVDT and RVDT position sensors. Flight-control surface position, throttle-lever angle, and many actuator rams use alternating-current-excited differential transformers. The analogue secondary voltages are demodulated to direct current (or processed as alternating-current amplitudes) and then digitised so flight-control and engine computers can close digital loops.
Temperature probes. Resistance temperature detectors and thermocouples on engines, hydraulic systems, and environmental-control systems produce millivolt or resistance changes that must be amplified, filtered, and converted before they appear on crew alerting displays or enter a FADEC limit schedule.
In each path the same sequence applies: analogue sensing, anti-alias filtering, sampling, quantisation to 2 n 2^n 2 n levels, and digital transmission. Category B2 staff must be able to explain why a “noisy” digital parameter may be an aliasing or resolution problem rather than a failed probe, and why replacing a sensor without confirming the analogue interface and reference voltages can leave the digital word still incorrect.
Worked Numerical Example: 12-bit Air-Data Channel
A unipolar analogue-to-digital converter in an air-data computer has a full-scale range of 0 V 0\text{ V} 0 V to 10.00 V 10.00\text{ V} 10.00 V and a resolution of 12 bits 12\text{ bits} 12 bits . A conditioned pitot-transducer voltage of 3.250 V 3.250\text{ V} 3.250 V is presented to the sampler.
Step 1 — Number of levels and LSB size 2 12 = 4096 levels , V LSB = 10.00 V 4096 = 2.441 mV 2^{12} = 4096 \text{ levels}, \quad V_{\text{LSB}} = \frac{10.00\text{ V}}{4096} = 2.441\text{ mV} 2 12 = 4096 levels , V LSB = 4096 10.00 V = 2.441 mV
Step 2 — Ideal code code = round ( 3.250 V 2.441 mV ) = round ( 1331.3 ) = 1331 \text{code} = \operatorname{round}\left(\frac{3.250\text{ V}}{2.441\text{ mV}}\right) = \operatorname{round}(1331.3) = 1331 code = round ( 2.441 mV 3.250 V ) = round ( 1331.3 ) = 1331
Step 3 — Quantisation error bound
Maximum error = ± 1.221 mV = \pm 1.221\text{ mV} = ± 1.221 mV , which is ± 0.012 % \pm 0.012\% ± 0.012% of full scale. Whether that error is acceptable depends on the pressure-to-voltage scale factor and the airspeed accuracy specification, not on the bit count alone.
Step 4 — Nyquist check
If the anti-alias filter cuts off at 25 Hz 25\text{ Hz} 25 Hz and f s = 200 Hz f_s = 200\text{ Hz} f s = 200 Hz , then f s / 2 = 100 Hz f_s/2 = 100\text{ Hz} f s /2 = 100 Hz , giving a factor-of-four guard band above 25 Hz 25\text{ Hz} 25 Hz . Energy at 400 Hz 400\text{ Hz} 400 Hz from the alternating-current bus must already be attenuated by the analogue filter; otherwise it aliases toward a near-direct-current offset or a low-frequency wander in the airspeed word.