Study guide

14.1 Airbus ECAM — Electronic Centralised Aircraft Monitoring

EASA Part-66 Module 05 — Digital Techniques / Electronic Instrument Systems Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Numbering Systems

1.1 Numbering Systems: Decimal, Binary, Octal and Hexadecimal 1.2 Binary Arithmetic and Signed Number Representation 1.3 Binary Coded Decimal, Gray Code and Alphanumeric Codes

2 Chapter 2: Data Conversion

2.1 Analogue and Digital Signals, Sampling and Quantisation 2.2 Digital-to-Analogue Converters 2.3 Analogue-to-Digital Converters

3 Chapter 3: ARINC 429 Data Buses

3.1 ARINC 429 Specification, Physical Layer and Topology 3.2 ARINC 429 32-Bit Word Architecture 3.3 ARINC 429 Transmission, Timing and Troubleshooting

4 Chapter 4: Advanced Avionics Data Buses and Aircraft Ethernet

4.1 ARINC 629 Digital Autonomous Terminal Access 4.2 MIL-STD-1553B Military Avionics Data Bus 4.3 AFDX / ARINC 664 Part 7 Avionics Full-Duplex Switched Ethernet

5 Chapter 5: Combinational Logic Gates and Boolean Algebra

5.1 Basic Logic Gates, Truth Tables and Logic Levels 5.2 Boolean Algebra, De Morgan Theorems and Logic Simplification 5.3 Universal Gates and Aircraft Combinational Applications

6 Chapter 6: Sequential Logic, Registers and Logic Diagrams

6.1 Bistable Multivibrators: SR, JK, D and T Flip-Flops 6.2 Shift Registers and Data Storage Elements 6.3 Asynchronous and Synchronous Counters and Logic-Diagram Interpretation

7 Chapter 7: Computer Structure and Microprocessors

7.1 Computer Architecture, Terminology and the Bus System 7.2 Semiconductor Memory Technologies 7.3 Microprocessor Operation, Instruction Cycles and I/O

8 Chapter 8: Integrated Circuits, Multiplexing and Integrated Modular Avionics

8.1 Integrated Circuit Technology, Encoders, Decoders and Scale of Integration 8.2 Multiplexing and Demultiplexing Techniques 8.3 Remote Data Concentrators and Integrated Modular Avionics

9 Chapter 9: Fibre Optics in Aviation

9.1 Physics of Light Transmission and Optical Fibres 9.2 Fibre Cable Types, Signal Degradation and Optical Components 9.3 Fibre Optic Maintenance, Termination, Splicing and Inspection

10 Chapter 10: Electronic Displays and Flight Instrument Layout

10.1 Display Technologies: CRT, LED and LCD 10.2 Electronic Flight Instrument System Architecture 10.3 Cockpit Symbology, Colour Standards and Display Reversion

11 Chapter 11: Electrostatic Sensitive Devices

11.1 Physics of Electrostatic Charge and Device Susceptibility 11.2 ESDS Damage Mechanisms: Catastrophic versus Latent Failures 11.3 ESDS Handling, Storage, Packaging and Workshop Procedures

12 Chapter 12: Software Management Control and Airworthiness

12.1 Aviation Software Classification and RTCA DO-178C / EUROCAE ED-12C 12.2 Software Configuration Management and Part Numbering 12.3 Data Loading, Integrity Verification and Unapproved Changes

13 Chapter 13: Electromagnetic Environment

13.1 Electromagnetic Interference and Compatibility 13.2 High Intensity Radiated Fields and RF Hazards 13.3 Lightning Protection, Bonding and Static Dischargers

14 Chapter 14: Engine Indication, Warning and Monitoring Systems

14.1 Airbus ECAM — Electronic Centralised Aircraft Monitoring 14.2 Boeing EICAS — Engine Indicating and Crew Alerting System 14.3 Comparison, Failure Reversion and Sensor Interfacing

15 Chapter 15: Flight Management, Navigation and Surveillance Systems

15.1 Flight Management System and Control Display Unit 15.2 Inertial Reference, AHRS/ADIRU Context and GPS 15.3 Traffic Collision Avoidance and Terrain Awareness

16 Chapter 16: Fly-By-Wire, BITE, ACARS, Cabin and Information Systems

16.1 Fly-By-Wire Flight Control 16.2 Built-In Test Equipment and Central Maintenance Computers 16.3 ACARS, Cabin Systems and Information Systems

14.1 Airbus ECAM — Electronic Centralised Aircraft Monitoring

Key Takeaways Explain This Topic AI

Electronic Centralised Aircraft Monitoring (ECAM, official spelling Centralised) uses an upper Engine/Warning Display for primary engine parameters plus warning, caution and memo messages, and a lower System Display for synoptic pages and status.

A typical Airbus teaching split uses dual System Data Acquisition Concentrators for synoptic data, dual Flight Warning Computers for alerts, aurals and flight-phase logic, and three Display Management Computers to format the images.

Alerting is ranked: red warning (immediate action, master warning, continuous repetitive chime), amber caution (awareness, master caution, single chime), advisory (pulsing parameter) and green memo (normal status).

Flight-phase inhibit typically defers selected caution-level messages during take-off and landing so that time-critical red warnings remain available; exact phase boundaries are type-specific.

ECAM computers include associated BITE that reports faults for centralised maintenance readout; the in-flight E/WD message field is an operational crew-alert display, not the isolation manual.

Last updated: September 2026

14.1 Airbus ECAM — Electronic Centralised Aircraft Monitoring

Current EASA Part-66 topic 5.15, Typical electronic / digital aircraft systems , is knowledge level 1 for categories A, B3, B1 and B2/B2L. The current Appendix I gives no system-by-system list; the pre-12 June 2024 detailed description explicitly included Electronic Centralised Aircraft Monitoring (ECAM) and associated Built-In Test Equipment (BITE) . This section retains ECAM as a representative historical study example. This section covers how a typical Airbus installation organises the Engine/Warning Display (E/WD) and System Display (SD) , and how advisory, caution and warning information is generated and inhibited by flight-phase logic. Exact ECAM action lines and Quick Reference Handbook drills belong on a type course, not in Module 5.

What ECAM Provides

ECAM is the Airbus name for the centralised engine-indication, systems-synoptic and crew-alerting function. A typical glass-cockpit Airbus puts four jobs on two display units: primary and supporting engine parameters; aircraft-system synoptic pages; colour-coded crew alerts (warning, caution, advisory and memo); and a status summary of inoperative systems after a failure. The crew must see the engine state continuously, be pointed at the affected system when something fails, and not be flooded with every amber message during take-off and landing. For the maintenance engineer, a missing parameter, a stuck memo, a blank display or an unexpected inhibit is often the first evidence of a failed sensor, a failed warning computer, or a display-reversion event.

Typical Computer Arrangement

Classroom teaching uses the A320-family split as the general arrangement. Later Airbus types keep the same ideas with different box names and display sizes. Processing is divided among specialised computers rather than placed in a single LRU.

Computer Typical quantity Familiarisation-level role

System Data Acquisition Concentrator (SDAC) 2 Acquires analogue, discrete and digital system data for synoptic pages. SDACs do not generate crew-alert messages.

Flight Warning Computer (FWC) 2 Generates warning, caution and memo messages, aural alerts and flight-phase inhibit logic.

Display Management Computer (DMC) 3 Formats PFD, ND and ECAM images. Typical teaching assigns DMC 3 to the two ECAM display units.

ECAM display units 2 Upper unit: E/WD . Lower unit: SD .

ECAM Control Panel (ECP) 1 Manual system-page selection, CLR / RCL / STS, brightness, and emergency cancel as fitted.

Dual SDACs and dual FWCs mean a single computer failure should not remove both synoptic data and alerting. Three DMCs allow an EFIS DMC to be switched onto the ECAM displays if DMC 3 fails. Engine parameters originate mainly in Full Authority Digital Engine Control (FADEC) or Electronic Engine Control (EEC) channels as digital words; fire detection, some oil-quantity sensors and other independent loops arrive on separate paths (section 14.3).

Engine/Warning Display (E/WD)

The upper ECAM display is the Engine/Warning Display. In normal operation it is the permanent engine and alert window, not a general systems page. Typical zones, from top to bottom, are the primary engine area ( N1 or engine pressure ratio (EPR) , exhaust gas temperature (EGT) , N2 and fuel flow , with limit marks and the active thrust limit), fuel-on-board and slat/flap cues, and the memo, warning and caution field. Left-side columns list titles; some types add right-side action reminders. Module 5 requires recognition that this colour-coded field exists, not memorising type-course action lines.

Green memo messages (seat-belt signs, APU available, speed-brake extended) confirm a selected or automatic aircraft state and are not failures. Pulsing advisory behaviour around a parameter (often taught as level 1) marks a value drifting toward a limit. Cautions (amber, typically level 2) and warnings (red, typically level 3) occupy the same field at higher priority. Overflow indication and clear/recall logic step through a stack that is too long for one screen. Independent failures remain listed; purely consequential effects may be suppressed so the same failure is not repeated in several disguises.

System Display (SD) and System Pages

The lower ECAM display is the System Display. It presents system synoptic pages and the status (STS) page rather than the permanent engine strip. A typical ECP allows the crew to call BLEED, PRESS, EL/AC, EL/DC, HYD, FUEL, APU, COND/AIR, DOOR/OXY, WHEEL, F/CTL, ENG and similar pages. Each page is a schematic of valves, pumps, buses, quantities, temperatures and pressures in the same red/amber/green/white language as the rest of the glass cockpit. The CRUISE page, when provided, is a condensed multi-system summary for the cruise phase.

Automatic page switching is part of the general arrangement: ENG during start or an engine-related failure; the affected synoptic after a system failure; DOOR or WHEEL on the ground or landing; STS after the operational failure drill is cleared. The SD is a context display . If the upper display fails, the E/WD image normally transfers onto the lower unit so that engine parameters and alerts are preserved; system pages then share an EFIS display via an ECAM/ND transfer switch.

Advisory, Caution and Warning Levels

ECAM alerting is taught as a ranked set of levels. Colours, lights and sounds must match the level.

Level (typical teaching) Crew meaning Typical colour Typical lights Typical aural

Warning (level 3) Immediate action Red Red MASTER WARN Continuous repetitive chime (CRC) or a specific warning tone

  • Caution (level 2) Awareness and timely action Amber Amber MASTER CAUT Single chime
  • Advisory (level 1) Parameter drifting toward a limit Pulsing parameter None (typical) None (typical)
  • Memo (level 0) Normal status reminder Green None None

Red is never used for a routine memo. Amber is never used to mean normal. Green completed indications mean the item is in the expected state. Cyan or blue action titles and white page labels must not be confused with the red/amber/green safety language. The master-warning and master-caution captions are driven by the FWCs. Pressing the light silences or resets attention-getters; it does not repair the system and it does not erase BITE memory.

Flight-Phase Inhibit as Typical Teaching

If every amber caution chimed at rotation, genuine red warnings could be missed. Flight-phase inhibit is FWC logic that uses airspeed, radio altitude, thrust-lever position, landing-gear discretes and similar inputs to defer selected caution-level messages during the most critical phases. Typical classroom teaching divides electrical power-up, engine start, take-off roll, climb, cruise, descent, approach, landing and post-landing into numbered phases, but the exact phase table is type-specific. During the take-off and landing inhibit windows many cautions are parked. Red warnings that protect against fire or similarly immediate hazards are generally not inhibited. After the window, previously inhibited cautions that are still present appear, often with the normal single chime. An engineer troubleshooting a missing amber message must ask whether the FWC considered the aircraft to be in an inhibit phase, not only whether a sensor failed.

Warning

Do not treat ECAM as a type-course procedure trainer. Module 5 asks for general arrangement: E/WD versus SD, system pages, the warning/caution/advisory/memo hierarchy, and the existence of flight-phase inhibit. Precise inhibit speeds and ECAM action lines are aeroplane-specific.

Associated BITE

ECAM computers include BITE . Power-up tests and continuous monitoring record faults against the SDAC, FWC, DMC and display-unit LRUs and usually report to a centralised maintenance computer or centralised fault-display system. Failures that affect the current flight appear as operational warnings or cautions. Lower-priority items may appear only on the STS page or only in the BITE readout. Using the E/WD as the maintenance manual is a category error. If the E/WD is blank but the SD is alive, suspect a display unit, DMC assignment or reversion. If system pages freeze while warnings still chime, suspect the SDAC path versus the FWC path. If a known amber failure is silent during take-off, check flight-phase inhibit before replacing sensors.

Loading diagram... Typical Airbus ECAM General Arrangement (Familiarisation)