Study guide

13.3 Lightning Protection, Bonding and Static Dischargers

EASA Part-66 Module 05 — Digital Techniques / Electronic Instrument Systems Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Numbering Systems

1.1 Numbering Systems: Decimal, Binary, Octal and Hexadecimal 1.2 Binary Arithmetic and Signed Number Representation 1.3 Binary Coded Decimal, Gray Code and Alphanumeric Codes

2 Chapter 2: Data Conversion

2.1 Analogue and Digital Signals, Sampling and Quantisation 2.2 Digital-to-Analogue Converters 2.3 Analogue-to-Digital Converters

3 Chapter 3: ARINC 429 Data Buses

3.1 ARINC 429 Specification, Physical Layer and Topology 3.2 ARINC 429 32-Bit Word Architecture 3.3 ARINC 429 Transmission, Timing and Troubleshooting

4 Chapter 4: Advanced Avionics Data Buses and Aircraft Ethernet

4.1 ARINC 629 Digital Autonomous Terminal Access 4.2 MIL-STD-1553B Military Avionics Data Bus 4.3 AFDX / ARINC 664 Part 7 Avionics Full-Duplex Switched Ethernet

5 Chapter 5: Combinational Logic Gates and Boolean Algebra

5.1 Basic Logic Gates, Truth Tables and Logic Levels 5.2 Boolean Algebra, De Morgan Theorems and Logic Simplification 5.3 Universal Gates and Aircraft Combinational Applications

6 Chapter 6: Sequential Logic, Registers and Logic Diagrams

6.1 Bistable Multivibrators: SR, JK, D and T Flip-Flops 6.2 Shift Registers and Data Storage Elements 6.3 Asynchronous and Synchronous Counters and Logic-Diagram Interpretation

7 Chapter 7: Computer Structure and Microprocessors

7.1 Computer Architecture, Terminology and the Bus System 7.2 Semiconductor Memory Technologies 7.3 Microprocessor Operation, Instruction Cycles and I/O

8 Chapter 8: Integrated Circuits, Multiplexing and Integrated Modular Avionics

8.1 Integrated Circuit Technology, Encoders, Decoders and Scale of Integration 8.2 Multiplexing and Demultiplexing Techniques 8.3 Remote Data Concentrators and Integrated Modular Avionics

9 Chapter 9: Fibre Optics in Aviation

9.1 Physics of Light Transmission and Optical Fibres 9.2 Fibre Cable Types, Signal Degradation and Optical Components 9.3 Fibre Optic Maintenance, Termination, Splicing and Inspection

10 Chapter 10: Electronic Displays and Flight Instrument Layout

10.1 Display Technologies: CRT, LED and LCD 10.2 Electronic Flight Instrument System Architecture 10.3 Cockpit Symbology, Colour Standards and Display Reversion

11 Chapter 11: Electrostatic Sensitive Devices

11.1 Physics of Electrostatic Charge and Device Susceptibility 11.2 ESDS Damage Mechanisms: Catastrophic versus Latent Failures 11.3 ESDS Handling, Storage, Packaging and Workshop Procedures

12 Chapter 12: Software Management Control and Airworthiness

12.1 Aviation Software Classification and RTCA DO-178C / EUROCAE ED-12C 12.2 Software Configuration Management and Part Numbering 12.3 Data Loading, Integrity Verification and Unapproved Changes

13 Chapter 13: Electromagnetic Environment

13.1 Electromagnetic Interference and Compatibility 13.2 High Intensity Radiated Fields and RF Hazards 13.3 Lightning Protection, Bonding and Static Dischargers

14 Chapter 14: Engine Indication, Warning and Monitoring Systems

14.1 Airbus ECAM — Electronic Centralised Aircraft Monitoring 14.2 Boeing EICAS — Engine Indicating and Crew Alerting System 14.3 Comparison, Failure Reversion and Sensor Interfacing

15 Chapter 15: Flight Management, Navigation and Surveillance Systems

15.1 Flight Management System and Control Display Unit 15.2 Inertial Reference, AHRS/ADIRU Context and GPS 15.3 Traffic Collision Avoidance and Terrain Awareness

16 Chapter 16: Fly-By-Wire, BITE, ACARS, Cabin and Information Systems

16.1 Fly-By-Wire Flight Control 16.2 Built-In Test Equipment and Central Maintenance Computers 16.3 ACARS, Cabin Systems and Information Systems

13.3 Lightning Protection, Bonding and Static Dischargers

Key Takeaways Explain This Topic AI

Typical industry teaching (SAE ARP5414 / EUROCAE ED-91) divides the airframe into lightning zones for first-return-stroke extremities, swept-stroke surfaces and conduction paths; use the type-specific drawing, not a universal map.

Bonding jumpers provide the designed current path across moving joints, doors, control surfaces and composite-to-metal interfaces and must remain short, clean and unpainted.

Static dischargers (wicks) bleed precipitation-static charge to reduce corona noise on radios; they are not a substitute for lightning bonding but often sit at likely exit or hang-on edges and are damaged in strikes.

Composite repairs must restore designed conductivity (mesh, foil, diverters, fastener bonds); isolated metal fittings can spark if left unbonded.

After a reported or suspected strike, follow the AMM inspection of likely entry and exit damage, jumpers, wicks, radomes, composites and systems; do not invent unpublished strike-current kiloamperes as EASA Module 5 facts.

Last updated: September 2026

13.3 Lightning Protection, Bonding and Static Dischargers

Topic 5.14 still sits at Level 2 for B1 and B2/B2L , Level 1 for B3 , and not required for Category A . Lightning is a different electromagnetic environment from HIRF: a high-current, short-duration attachment and dwell on the airframe, with possible reattachment as the flash is swept aft. The influence on maintenance practices is the zoning concept (as typical industry teaching), bonding jumpers , static dischargers , composite conductivity , and inspection after a strike .

How lightning involves the aeroplane

Aircraft often trigger lightning when they fly through a charged cloud, rather than simply being hit at random. A leader attaches at a likely extremity; current flows through the structure; the flash may dwell and then sweep aft as the aeroplane moves, creating further attachment spots. Energy also couples into wiring ( indirect effects ): induced voltages and currents that can upset or damage avionics even when the skin is not holed.

Design organisations use standardised current components (first return stroke, intermediate current, continuing current, subsequent strokes, multiple bursts) published in industry lightning-environment documents such as SAE ARP5412 / EUROCAE ED-84 . Those waveforms are certification design environments . They are not a set of kiloampere figures in EASA Part-66 Appendix I. Do not treat a peak current as a Module 5 fact, do not invent unpublished strike-current numbers, and do not try to “measure the strike” on the ramp with a clamp meter. The technician’s job is configuration and inspection , not reconstructing the waveform.

Zoning as typical teaching

Industry lightning zoning (typically SAE ARP5414 / EUROCAE ED-91 ) divides the outside of the aeroplane according to the probability of attachment and the type of current expected there. Exact zone drawings are type-specific (in the AMM or lightning-protection drawings). The teaching pattern is:

Typical zone idea What it means for teaching Hangar implication

First-return-stroke extremities (often taught as Zone 1A and related 1-series surfaces) Nose, wing tips, empennage tips, engine-inlet lips, propeller blades and similar projections are likely initial attachment regions Look here first for pits, holes, burnt paint, damaged pitot/static probes and antennas

Swept-stroke surfaces (often taught as Zone 2-series) After initial attachment the flash is dragged aft along skins, flaps and fairings Search aft of the nose and tips for a trail of marks, fastener sparking and composite puncture

Hang-on trailing edges (often taught as 1B/2B-style edges) The flash may remain attached at a trailing edge while current continues Trailing-edge structure, static dischargers and control-surface bonds

Conduction / low-attachment regions (often taught as Zone 3) Direct attachment is less likely, but current still flows between entry and exit through structure and designated bonds Hidden damage: bonding jumpers, hinges, pipe bonds, fuel-tank fastener interfaces

Do not invent a universal millimetre map of zones for every type. Use the aircraft lightning-zone diagram in the maintenance data when inspecting. Zoning is a search pattern , not a licence to skip a jumper that happens to sit in a “quiet” painted area on a training sketch.

Bonding jumpers and structural current paths

The metal (or protected composite) airframe is intended to carry lightning current in a controlled path so that the interior is not the preferred route. Bonding jumpers close gaps that the structure cannot: control-surface hinges, engine-cowl doors, landing-gear doors, spoilers, flaps, moving radomes, and composite-to-metal joints.

Rules that follow from section 13.1 and become critical in a strike:

Jumpers must be the specified part , short , and landed on clean conducting structure .

A painted or corroded lug forces current into fasteners, sealant or fuel-tank interfaces where sparking is unacceptable.

Isolated metal fittings in composite (latches, hinges, plumbing) must have the designed bond or they can spark to the nearest fibre or mesh.

Do not add unofficial extra straps that create a new path through a tank or a wiring bundle.

Fuel-tank ignition prevention (continuing-airworthiness programmes that grew from fuel-tank safety work) depends on known electrical paths and fastener design. Unofficial bonding “improvements” are a safety failure, not initiative. After any structural or composite repair that disturbs a jumper land, restore the bond and perform the milliohmmeter check the AMM requires.

Static dischargers (static wicks)

Precipitation static (P-static) charges the airframe as ice, rain or dust strikes the surface. Charge bleeds by corona , which produces broadband radio noise on HF and VHF. Static dischargers (wicks, typically on trailing edges of wings, ailerons, elevators and rudder) provide sharp points so that corona occurs off the trailing edge at a controlled location, reducing coupling into antennas.

Static dischargers are not a substitute for lightning bonding and are not the primary down-conductor of the airframe. They do, however, sit on trailing edges that are likely lightning exit or hang-on points , so they are frequently melted, shortened or missing after a strike. Inspect them for that reason and for radio-noise complaints. Resistance and mechanical-condition limits come from the AMM , not from a single Module 5 megohm figure. Do not fly with a set of missing wicks just because the aeroplane is metal: the radio-noise and lightning-exit inspections still apply as written.

Composite conductivity

Carbon laminates need the designed conductive layer to spread lightning current and to keep HIRF skin currents on the outside. Maintenance implications:

Follow the structural repair manual electrical steps (mesh overlap, conductive adhesive, surface ply, fastener bonding).

After paint, restore diverter strips on radomes and any unpainted bonding lands.

Check that metal mesh is not wrenched into an isolated island by a poorly scarfed repair.

Treat a composite puncture or fibre bloom after a strike as structural and electrical damage.

A fair aerodynamic repair that omits conductivity can leave a puncture path into a tank boundary or a wiring run on the next strike, and it can reopen the HIRF aperture discussed in section 13.2.

Inspection after lightning

Crews may report a flash, a bang, transient instruments, a burnt smell, or nothing but a mark found on walk-round. Treat a reported or suspected strike as an AMM lightning-strike inspection, not as a polish-out.

Typical teaching sequence (always overridden by the type AMM):

External search of likely entry and exit: nose, tips, radome, engine inlets, wing and tail trailing edges, static dischargers, antennas, lights, pitot probes.

Marks: pits, burn marks, punctures, delamination, missing paint, exploded fasteners, damaged bonding jumpers.

Systems: popped breakers, spurious warnings, compass or inertial-reference behaviour, radio performance, fuel-quantity anomalies.

Progressive inspection as the AMM requires if damage is found (deeper non-destructive testing, tank areas, hidden bonds).

Do not release the aeroplane until the required inspection and any repairs are complete.

Warning

Do not invent the current. A small surface pit does not tell you the peak kiloamperes, and a spectacular exit hole does not authorise skipping hidden-bond and tank-interface inspections. Use the AMM criteria. Unpublished strike-current numbers are not EASA Module 5 facts.

B1/B2 Level 2 means you can apply zoning as a search pattern, explain bonding and wicks, and carry out (or call for) a lightning-strike inspection. B3 Level 1 means you recognise that lightning-protection hardware and post-strike inspection are airworthiness tasks.

Loading diagram... Lightning attachment, structural current path, bonding jumpers and static dischargers