Study guide
8.2 Multiplexing and Demultiplexing Techniques
EASA Part-66 Module 05 — Digital Techniques / Electronic Instrument Systems Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Numbering Systems
1.1 Numbering Systems: Decimal, Binary, Octal and Hexadecimal 1.2 Binary Arithmetic and Signed Number Representation 1.3 Binary Coded Decimal, Gray Code and Alphanumeric Codes
2 Chapter 2: Data Conversion
2.1 Analogue and Digital Signals, Sampling and Quantisation 2.2 Digital-to-Analogue Converters 2.3 Analogue-to-Digital Converters
3 Chapter 3: ARINC 429 Data Buses
3.1 ARINC 429 Specification, Physical Layer and Topology 3.2 ARINC 429 32-Bit Word Architecture 3.3 ARINC 429 Transmission, Timing and Troubleshooting
4 Chapter 4: Advanced Avionics Data Buses and Aircraft Ethernet
4.1 ARINC 629 Digital Autonomous Terminal Access 4.2 MIL-STD-1553B Military Avionics Data Bus 4.3 AFDX / ARINC 664 Part 7 Avionics Full-Duplex Switched Ethernet
5 Chapter 5: Combinational Logic Gates and Boolean Algebra
5.1 Basic Logic Gates, Truth Tables and Logic Levels 5.2 Boolean Algebra, De Morgan Theorems and Logic Simplification 5.3 Universal Gates and Aircraft Combinational Applications
6 Chapter 6: Sequential Logic, Registers and Logic Diagrams
6.1 Bistable Multivibrators: SR, JK, D and T Flip-Flops 6.2 Shift Registers and Data Storage Elements 6.3 Asynchronous and Synchronous Counters and Logic-Diagram Interpretation
7 Chapter 7: Computer Structure and Microprocessors
7.1 Computer Architecture, Terminology and the Bus System 7.2 Semiconductor Memory Technologies 7.3 Microprocessor Operation, Instruction Cycles and I/O
8 Chapter 8: Integrated Circuits, Multiplexing and Integrated Modular Avionics
8.1 Integrated Circuit Technology, Encoders, Decoders and Scale of Integration 8.2 Multiplexing and Demultiplexing Techniques 8.3 Remote Data Concentrators and Integrated Modular Avionics
9 Chapter 9: Fibre Optics in Aviation
9.1 Physics of Light Transmission and Optical Fibres 9.2 Fibre Cable Types, Signal Degradation and Optical Components 9.3 Fibre Optic Maintenance, Termination, Splicing and Inspection
10 Chapter 10: Electronic Displays and Flight Instrument Layout
10.1 Display Technologies: CRT, LED and LCD 10.2 Electronic Flight Instrument System Architecture 10.3 Cockpit Symbology, Colour Standards and Display Reversion
11 Chapter 11: Electrostatic Sensitive Devices
11.1 Physics of Electrostatic Charge and Device Susceptibility 11.2 ESDS Damage Mechanisms: Catastrophic versus Latent Failures 11.3 ESDS Handling, Storage, Packaging and Workshop Procedures
12 Chapter 12: Software Management Control and Airworthiness
12.1 Aviation Software Classification and RTCA DO-178C / EUROCAE ED-12C 12.2 Software Configuration Management and Part Numbering 12.3 Data Loading, Integrity Verification and Unapproved Changes
13 Chapter 13: Electromagnetic Environment
13.1 Electromagnetic Interference and Compatibility 13.2 High Intensity Radiated Fields and RF Hazards 13.3 Lightning Protection, Bonding and Static Dischargers
14 Chapter 14: Engine Indication, Warning and Monitoring Systems
14.1 Airbus ECAM — Electronic Centralised Aircraft Monitoring 14.2 Boeing EICAS — Engine Indicating and Crew Alerting System 14.3 Comparison, Failure Reversion and Sensor Interfacing
15 Chapter 15: Flight Management, Navigation and Surveillance Systems
15.1 Flight Management System and Control Display Unit 15.2 Inertial Reference, AHRS/ADIRU Context and GPS 15.3 Traffic Collision Avoidance and Terrain Awareness
16 Chapter 16: Fly-By-Wire, BITE, ACARS, Cabin and Information Systems
16.1 Fly-By-Wire Flight Control 16.2 Built-In Test Equipment and Central Maintenance Computers 16.3 ACARS, Cabin Systems and Information Systems
8.2 Multiplexing and Demultiplexing Techniques
Key Takeaways Explain This Topic AI
A multiplexer with 2^n data inputs needs n select (data-select) lines and, when enabled, routes exactly one input to a single output.
A demultiplexer is the inverse: one data input is steered to one of 2^n outputs under the same n-bit select code; a decoder with the data fed into an enable pin is often used as a demultiplexer.
On logic diagrams identify a mux by the MUX (or n-1) label, 2^n data pins, n select pins, one Y output and usually an active-low enable; complementary W outputs appear on devices such as the 74151.
Time-division multiplexing shares one path by time slots; frequency-division multiplexing shares a medium by carrier frequency. Aircraft analogue CMOS muxes (4051-class) time-scan sensors into an ADC, while digital buses place successive words on one pair.
Last updated: September 2026
8.2 Multiplexing and Demultiplexing Techniques
Module 5.9, Multiplexing, is a Category B2/B2L knowledge-level-2 topic. Multiplexer/demultiplexer operation, application, and identification in logic diagrams come from the pre-12 June 2024 detailed Appendix I description. Categories A, B3 and B1 are not examined on 5.9, but every electronic instrument system that shares a wire, an ADC channel or a cockpit display refresh path is using the same idea. This section treats the combinational MSI blocks first, then the enable pin, then how the same function is drawn on a schematic, and finally how time-division and frequency-division multiplexing appear in aircraft analogue and digital hardware.
Data select: 2^n inputs and n select lines
A digital multiplexer (mux, data selector) is a combinational switch. It has 2^n data inputs, n select or address lines, usually one enable (strobe), and one output. The select code chooses which single data input is connected through to the output. An 8-to-1 multiplexer therefore has eight data pins (D0–D7), three select pins (S2 S1 S0), one enable, and one Y output. A 4-to-1 device uses two select pins; a 2-to-1 device uses one; a 16-to-1 device uses four. The rule is strict: if you count data inputs and they are not a power of two, you are not looking at a single binary-addressed mux — you may be looking at several muxes with a common enable, or at an analogue switch array with a different pin-out.
Boolean form for a 4-to-1 mux with active-high enable E is:
Y = E · (D0·S1'·S0' + D1·S1'·S0 + D2·S1·S0' + D3·S1·S0)
If E is false, Y is forced to a defined inactive level (or open-collector off), regardless of data and select. That is how several mux packages are expanded: two 8-to-1 devices plus a 2-to-1 device, or two 8-to-1 devices with complementary enables, build a 16-to-1 selector without inventing a new MSI part.
Textbook TTL parts you should recognise by pin function, not by memorising every number, are the 74151 (8-to-1 with complementary Y and W outputs), 74153 (dual 4-to-1), 74157 (quad 2-to-1, often used to steer a 4-bit nibble from one of two sources) and 74150 (16-to-1). CMOS 74HC/HCT versions of the same functions appear on later cards. Analogue CMOS multiplexers such as the 4051 (8-channel), 4052 (dual 4-channel) and 4053 (triple 2-channel) pass a voltage rather than a logic level; they are the usual front-end when one ADC must scan many sensors.
Worked select code. On an 8-to-1 mux, S2 S1 S0 = 101 binary (decimal 5) connects D5 to Y, provided the enable is asserted. If the enable is the wrong polarity — a common wiring-diagram error — Y stays inactive for every select code and the circuit looks like a dead source.
Demultiplexers
A demultiplexer (demux, distributor) is the inverse: one data input, n select lines, 2^n outputs. The select code steers the single data bit (or analogue voltage) to one output; the other outputs stay inactive. A 1-to-8 demux therefore has three select pins and eight outputs. In TTL catalogues you often do not buy a part labelled “demultiplexer”; you buy a decoder with an enable, and you feed the serial data into that enable. The 74138 3-to-8 decoder used as a demux is the standard teaching identification: address pins select which output may go active, and the data pin (on G1 or a G2 input) decides whether that output actually pulses. That is why topic 5.8 (decoders) and topic 5.9 (multiplexers/demultiplexers) sit next to each other on the syllabus — the same MSI package can be either function depending on how the enable is driven.
A mux followed by a demux with the same select code reconstructs the original parallel sources after they have shared one wire. If the select codes are not common — different clocks, different wiring, or a stuck select bit — the reconstructed channels appear swapped or silent. That is a classic ground-test pattern on analogue scanning systems: one thermocouple channel reads another sensor’s temperature.
Enable, expansion and identification on logic diagrams
The enable (G, E, EN, or STROBE) is not optional decoration. It qualifies the whole device. Active-low enables are drawn with a bubble; two active-low enables ANDed inside the package (74151, 74138) must both be low. Cascading uses the enable as a higher-order address bit. When you identify the symbol on an aircraft logic diagram, look for this cluster together:
Function name MUX, DMUX, DATA SEL, 8-1, 4-1, or 1-8.
A trapezoid or rectangular IEC box with many data pins on one face and a single Y (and maybe W) on the other.
Select/address pins labelled S0, S1, S2 or A, B, C, often with binary weights 1-2-4.
An enable pin, frequently active-low.
For analogue switches, a bidirectional analogue-path symbol rather than a logic Y, plus a VEE pin on some 4000-series parts.
Do not confuse a mux with a decoder. A decoder has n inputs and 2^n outputs and no “data” pin other than enables. Do not confuse a mux with a priority encoder: the encoder compresses many inputs into a code; the mux uses a code to pick one input. A rectangle with only clock and Q/Q-bar is a flip-flop, not a multiplexer. Four BCD pins and seven segment pins are a BCD-to-7-segment decoder from section 8.1, not a mux.
Device Data I/O Select lines Enable use Typical aircraft job
8-to-1 digital mux (74151 class) 8 inputs, 1 output (Y and often W) 3 Gates the whole selector; polarity must match the diagram Choose one of eight status bits or one of eight bus sources
Quad 2-to-1 (74157 class) Four independent 2-to-1 slices 1 common select Common enable for all four bits Steer a nibble from bus A or bus B
3-to-8 decoder as demux (74138 class) 1 data-on-enable, 8 outputs 3 Enable carries the serial/data bit Distribute a strobe or serial bit to one of eight loads
CMOS analogue 8-ch mux (4051 class) 8 analogue channels, 1 common 3 Inhibit opens all switches Scan thermocouples, RTDs, fuel probes or synchro/resolver voltages into one ADC
Time-division versus frequency-division multiplexing
Two different sharing methods appear in avionics teaching and must not be swapped.
Time-division multiplexing (TDM) assigns the shared path to one source at a time. In digital hardware that is exactly what a mux does: during slot 5, D5 owns the output. Sampled analogue systems do the same: a 4051 steps through sensors, an ADC converts each voltage, and software labels the result. Aircraft data buses are TDM in the broad sense that successive words occupy the same wire at successive times — an ARINC 429 pair carries many labels, one 32-bit word after another, rather than one dedicated pair per parameter. Display refresh and discrete scanners are also TDM.
Frequency-division multiplexing (FDM) assigns each channel a different carrier frequency so several signals can occupy the medium at the same instant. VHF communications, navigation beams and some analogue audio/video distribution are FDM problems. You do not select FDM channels with a 74151; you select them with tuned filters, mixers or a radio. Mention FDM in a Module 5.9 answer only as the contrasting method: same idea of sharing, different physical mechanism.
A mixed aircraft example is an analogue input card in a remote concentrator: CMOS analogue mux (TDM scanning) feeds an ADC; the digital results then share a data bus (TDM words); the VHF voice that the crew hears on the same aeroplane is still FDM at radio frequency. The maintenance implication is different in each layer. A stuck select line on the analogue mux aliases every channel to one sensor. A bus-label fault loses parameters by identity, not by carrier. An FDM radio fault is a receiver/transmitter problem, not an MSI data-selector problem.
Aircraft analogue and digital applications
Analogue multiplexing exists wherever many slowly changing voltages would otherwise each need a dedicated ADC and a long wire. Engine and airframe thermocouples, resistance temperature detectors, fuel-quantity tank probes, potentiometric position sensors, and older inertial-system synchro/resolver chains are scanned this way. The mux must preserve analogue accuracy: on-resistance, leakage and break-before-make switching matter, which is why analogue CMOS parts, not TTL 74151s, are used in that role. Digital multiplexing exists wherever many logic sources share a pin, a backplane or a display: nibble steering with 74157 devices, interrupt or discrete concentration, and the select logic in front of a shared UART or ARINC controller.
When you read a logic diagram in the aircraft wiring manual, name the block first (mux or demux), count data pins against 2^n, count select pins against n, note enable polarity, and only then trace the selected channel. If the count does not fit 2^n, look for cascaded packages or for an analogue switch that is not binary-addressed in the way the TTL data selector is. That identification sequence develops the “identification in logic diagrams” language from the former detailed 5.9 description.