Study guide
6.1 Bistable Multivibrators: SR, JK, D and T Flip-Flops
EASA Part-66 Module 05 — Digital Techniques / Electronic Instrument Systems Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Numbering Systems
1.1 Numbering Systems: Decimal, Binary, Octal and Hexadecimal 1.2 Binary Arithmetic and Signed Number Representation 1.3 Binary Coded Decimal, Gray Code and Alphanumeric Codes
2 Chapter 2: Data Conversion
2.1 Analogue and Digital Signals, Sampling and Quantisation 2.2 Digital-to-Analogue Converters 2.3 Analogue-to-Digital Converters
3 Chapter 3: ARINC 429 Data Buses
3.1 ARINC 429 Specification, Physical Layer and Topology 3.2 ARINC 429 32-Bit Word Architecture 3.3 ARINC 429 Transmission, Timing and Troubleshooting
4 Chapter 4: Advanced Avionics Data Buses and Aircraft Ethernet
4.1 ARINC 629 Digital Autonomous Terminal Access 4.2 MIL-STD-1553B Military Avionics Data Bus 4.3 AFDX / ARINC 664 Part 7 Avionics Full-Duplex Switched Ethernet
5 Chapter 5: Combinational Logic Gates and Boolean Algebra
5.1 Basic Logic Gates, Truth Tables and Logic Levels 5.2 Boolean Algebra, De Morgan Theorems and Logic Simplification 5.3 Universal Gates and Aircraft Combinational Applications
6 Chapter 6: Sequential Logic, Registers and Logic Diagrams
6.1 Bistable Multivibrators: SR, JK, D and T Flip-Flops 6.2 Shift Registers and Data Storage Elements 6.3 Asynchronous and Synchronous Counters and Logic-Diagram Interpretation
7 Chapter 7: Computer Structure and Microprocessors
7.1 Computer Architecture, Terminology and the Bus System 7.2 Semiconductor Memory Technologies 7.3 Microprocessor Operation, Instruction Cycles and I/O
8 Chapter 8: Integrated Circuits, Multiplexing and Integrated Modular Avionics
8.1 Integrated Circuit Technology, Encoders, Decoders and Scale of Integration 8.2 Multiplexing and Demultiplexing Techniques 8.3 Remote Data Concentrators and Integrated Modular Avionics
9 Chapter 9: Fibre Optics in Aviation
9.1 Physics of Light Transmission and Optical Fibres 9.2 Fibre Cable Types, Signal Degradation and Optical Components 9.3 Fibre Optic Maintenance, Termination, Splicing and Inspection
10 Chapter 10: Electronic Displays and Flight Instrument Layout
10.1 Display Technologies: CRT, LED and LCD 10.2 Electronic Flight Instrument System Architecture 10.3 Cockpit Symbology, Colour Standards and Display Reversion
11 Chapter 11: Electrostatic Sensitive Devices
11.1 Physics of Electrostatic Charge and Device Susceptibility 11.2 ESDS Damage Mechanisms: Catastrophic versus Latent Failures 11.3 ESDS Handling, Storage, Packaging and Workshop Procedures
12 Chapter 12: Software Management Control and Airworthiness
12.1 Aviation Software Classification and RTCA DO-178C / EUROCAE ED-12C 12.2 Software Configuration Management and Part Numbering 12.3 Data Loading, Integrity Verification and Unapproved Changes
13 Chapter 13: Electromagnetic Environment
13.1 Electromagnetic Interference and Compatibility 13.2 High Intensity Radiated Fields and RF Hazards 13.3 Lightning Protection, Bonding and Static Dischargers
14 Chapter 14: Engine Indication, Warning and Monitoring Systems
14.1 Airbus ECAM — Electronic Centralised Aircraft Monitoring 14.2 Boeing EICAS — Engine Indicating and Crew Alerting System 14.3 Comparison, Failure Reversion and Sensor Interfacing
15 Chapter 15: Flight Management, Navigation and Surveillance Systems
15.1 Flight Management System and Control Display Unit 15.2 Inertial Reference, AHRS/ADIRU Context and GPS 15.3 Traffic Collision Avoidance and Terrain Awareness
16 Chapter 16: Fly-By-Wire, BITE, ACARS, Cabin and Information Systems
16.1 Fly-By-Wire Flight Control 16.2 Built-In Test Equipment and Central Maintenance Computers 16.3 ACARS, Cabin Systems and Information Systems
6.1 Bistable Multivibrators: SR, JK, D and T Flip-Flops
Key Takeaways Explain This Topic AI
A latch is level-sensitive and can change Q for the whole time enable is active; an edge-triggered flip-flop updates Q only on a specified clock edge.
On an active-high NOR SR latch, S = 1 and R = 1 is the forbidden state: Q and NOT Q are both forced to 0, and the next hold state is a race.
A JK flip-flop with J = 1 and K = 1 toggles Q on the clock edge; that combination is defined behaviour, not the SR forbidden row.
A D flip-flop captures D at the clock edge (next Q equals D) and then holds, which is why it is the standard memory bit and discrete sampler.
A T flip-flop with T = 1 divides the clock by two; T = 0 holds. Aircraft uses include switch debounce (SR) and latched warning memory bits (SR or D).
Last updated: September 2026
6.1 Bistable Multivibrators: SR, JK, D and T Flip-Flops
Commission Implementing Regulation (EU) 2023/989 sets Appendix I topic 5.5(a), Identification and applications , at knowledge level 2 for both category B1 and category B2/B2L . Categories A and B3 are not examined on 5.5. Sequential applications — devices that store a bit — are taught here as a practical expansion of that broad heading. Interpretation of complete logic diagrams is a separate head, 5.5(b) , examined at level 2 for B2/B2L only ; B1 is not required to interpret diagrams at that depth. Module 5 is a multiple-choice paper: B2 sits 72 questions in 90 minutes , B1 sits 40 questions in 50 minutes , A/B3 sit 20 questions in 25 minutes , with a 75% pass mark , no negative marking, and no essay . The live paper uses three options; the practice items in this chapter use four options.
Combinational gates (AND, OR, NAND, NOR, XOR) produce an output that is a function of the present inputs only . Sequential logic adds memory : the output depends on the present inputs and on a stored previous state. That memory cell is the bistable multivibrator . A bistable has two stable states, conventionally Q = 1 (set) and Q = 0 (reset). The complementary pin, written NOT Q or Q-bar, is the inverse of Q when the cell is healthy. Two families appear on aircraft digital cards: the latch , which is level-sensitive, and the edge-triggered flip-flop , which updates only on a specified clock transition.
Latch versus edge-triggered flip-flop
A latch remains transparent while its enable (or gated clock) sits at the active level: Q can follow the data pins for the whole of that interval. When enable returns inactive, the last value is held . An edge-triggered flip-flop samples its controlling pins only at a rising or falling clock edge, then ignores those pins until the next edge. Aircraft sequential designs almost always distribute a common square-wave clock so that a bank of bits updates together. Treating a transparent latch as if it were edge-triggered is a standard maintenance error: a bouncing discrete on a still-enabled latch chatters Q, whereas the same bounce arriving between clock edges of a flip-flop is ignored.
The clock pin on a flip-flop symbol carries a triangle . No inversion bubble on that triangle means a rising-edge trigger; a bubble means a falling-edge trigger. A latch symbol uses an enable labelled EN or G and has no edge triangle. Asynchronous preset (PR) and clear (CLR) pins, often active-low (drawn with bubbles), override the clocked path and force Q immediately. Setup time is the interval for which data must be stable before the capturing edge; hold time is the interval it must remain stable after the edge. Violating either can leave the cell metastable — Q hovers between 0 and 1 before collapsing at random — which on the aircraft looks like an intermittent latched discrete that sometimes stores the new value and sometimes does not.
SR latch: Set, Reset and the forbidden state
The SR (Set–Reset) latch is the elementary bistable. Cross-coupled NOR gates give an active-high SR; cross-coupled NAND gates give an active-low S-bar / R-bar latch. For the NOR (active-high) version the four input rows are:
- S R Action on Q Notes
- 0 0 Hold (memory) Both inputs released; last state remains
- 1 0 Set Q becomes 1 and remains 1 after S returns to 0
- 0 1 Reset Q becomes 0 and remains 0 after R returns to 0
- 1 1 Forbidden Both NOR outputs forced to 0, so Q and NOT Q are no longer complementary
When S = 1 and R = 1 , the latch is in the forbidden (invalid) state . Releasing both inputs back to 0 then starts a race : whichever gate is slightly faster wins, so the next stored bit is unpredictable. Exam items often present S = R = 1 and ask why a designer must prevent it. On an aircraft schematic the usual preventives are mechanically exclusive contacts (a break-before-make SPDT switch cannot close Set and Reset together) or a combinational interlock in front of S and R.
A clocked (gated) SR latch ANDs S and R with an enable so that the pins are ignored unless the clock level is active. The forbidden combination still exists while the latch is enabled. Tying R to NOT D converts the gated SR into a D latch and deletes the forbidden row, because a single data pin cannot demand Set and Reset at once.
For the NAND active-low latch the hold combination is S-bar = R-bar = 1 (both pins released high) and the forbidden combination is S-bar = R-bar = 0 (both pins pulled low). Read the bubbles on the drawing: active-low Set is asserted by a 0 , not by a 1.
JK flip-flop: J = K = 1 is toggle, not forbidden
The JK flip-flop keeps the SR idea but redefines the both-asserted combination as toggle . J behaves like Set, K like Reset, and a clock edge is required.
- J K Next Q after the clock edge
- 0 0 Hold — Q unchanged
- 0 1 Reset — Q becomes 0
- 1 0 Set — Q becomes 1
- 1 1 Toggle — Q becomes the complement of present Q
When J = 1 and K = 1 , Q flips on every capturing edge. That is defined behaviour — it is not the SR forbidden row. The characteristic equation is next-Q = (J AND NOT Q) OR (NOT K AND Q). A JK with J and K strapped together is a T flip-flop; a JK held with J = K = 1 on every clock is a divide-by-two stage.
If a JK were merely a level-sensitive latch, holding J = K = 1 for the whole clock pulse would let Q toggle at gate-delay rate (the 1s-catching race). Master–slave JK cells and modern edge-triggered JK cells sample J and K only at the edge, so one clock produces one toggle. On a schematic, look for the edge triangle before predicting toggle.
Aircraft use of JK includes a memory bit with separate Set (J) and Reset (K) from two system computers, a binary divider when J = K = 1, and the first stage of a synchronous counter (section 6.3).
D flip-flop: capture of one data bit
The D (data, sometimes called delay) flip-flop has one data pin D and a clock. On the capturing edge, Q becomes equal to D . Between edges Q holds. The characteristic is simply next-Q = D. There is no forbidden data combination through D. Many packaged D cells still expose asynchronous PR and CLR; those pins must sit inactive (usually high if they are active-low) unless a power-up reset is required.
A register is a row of D flip-flops sharing a clock. Capturing a discrete on a defined edge is why D cells appear on aircraft input cards: a squat-switch, a thrust-lever idle discrete, or a fire-handle microswitch is filtered and then sampled so that contact bounce between clocks never reaches the warning computer. Q is then a clean memory bit for the rest of the frame.
T flip-flop: dedicated toggle
The T (toggle) flip-flop has input T and a clock. T = 0 holds; T = 1 toggles Q on the edge. Frequency at Q is half the clock frequency while T remains 1, which is why T stages form binary counters and 1 Hz elapsed-time ticks from a faster crystal. A T cell is a JK with J = K = T, or a D cell with D wired to NOT Q when T is 1.
Aircraft applications: debounce and memory bits
Two 5.5(a) sequential applications dominate Module 5 teaching.
Contact debounce. A mechanical toggle or limit switch does not close cleanly. Over a few milliseconds the contacts bounce, producing a burst of edges. If that raw discrete clocks a counter or a warning computer, one throw is counted many times. An SR latch driven by two break-before-make contacts (one Set, one Reset) captures a single transition and holds it until the opposite contact asserts Reset. An alternative is an RC filter into a Schmitt trigger feeding a D flip-flop that samples after the bounce window. The stored Q is the debounced discrete.
Memory bits (latched discretes). Fire warnings, many latched cautions, and BITE fault-captured bits must remain asserted after the initiating spike has gone. A 20 ms overcurrent that only drove a combinational AND would light a caption for 20 ms and then go dark — useless to the crew. An SR or D cell Sets on the event and holds Q = 1 until a guarded Reset, a valid 'condition gone AND reset selected' AND-gate, or a flight-leg power cycle. When a schematic shows a rectangle with Q and a clock triangle, treat it as a memory bit. When it shows cross-coupled NAND or NOR, treat it as an SR latch and look for the interlock that prevents S = R = 1.