Study guide

7.2 Rivet Spacing, Pitch, Edge Distance & Structural Layout

EASA Part-66 Module 07 — Maintenance Practices Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Safety Precautions — Electricity, Gases & Chemical Hazards

1.1 Electrical-System Hazards, Isolation & Protective Equipment 1.2 Compressed Gases, Pressure Vessels & Oxygen System Safety 1.3 Hazardous Chemicals, Solvents, Oils & Personal Protective Equipment

2 Chapter 2: Safety Precautions — Fire Protection, Confined Spaces & Emergency Response

2.1 Fire Classifications, Extinguishing Agents & Asphyxiation Risks 2.2 Confined-Space Entry, Fuel-Tank Safety & CDCCL Control 2.3 Emergency Response, Accident Remediation & Ballistic Recovery Systems

3 Chapter 3: Workshop Practices, Hand Tools & Precision Measurement

3.1 Workshop Housekeeping, Tool Control & Foreign Object Debris (FOD) 3.2 Engineering Dimensions, Allowances & Tolerances 3.3 Hand Tools, Powered Equipment & Operating Safety 3.4 Precision Measuring Instruments & Standards Traceability

4 Chapter 4: Fastener Torquing & Avionic Test Equipment

4.1 Torque Wrenches, Extension Calculations & Calibration Care 4.2 Multimeters, Megohmmeters & Insulation Testing 4.3 Bonding Testers, Milliohmmeters & Oscilloscopes

5 Chapter 5: Engineering Drawings, Standards & Fits

5.1 Orthographic Projections, Title Blocks & Revision Control 5.2 Drawing Line Conventions, Symbols & ATA Specification 100/iSpec 2200 5.3 Electrical Schematics, Wiring Interconnects & Component Location 5.4 Systems of Limits, Fits, Clearances & Shaft Alignment

6 Chapter 6: Electrical Wiring Interconnection System (EWIS)

6.1 EWIS Principles, Wire Types & Loom Routing Practices 6.2 Crimp Terminations, Connector Pin Insertion & Extraction Tooling 6.3 Electrical Bonding, Grounding Resistance & Electromagnetic Shielding

7 Chapter 7: Aircraft Riveting Practice

7.1 Solid and Blind Rivet Classifications, Materials & Head Markings 7.2 Rivet Spacing, Pitch, Edge Distance & Structural Layout 7.3 Countersinking, Dimpling Techniques & Rivet Installation 7.4 Rivet Joint Inspection, Failure Modes & Drill-Out Procedures

8 Chapter 8: Sheet Metal Working & Composite Materials

8.1 Sheet Metal Forming, Neutral Axis & Bend Allowance Calculations 8.2 Welding, Brazing, Soldering & Structural Adhesive Bonding 8.3 Composite Reinforcements, Pre-Preg Cold Storage & Clean Room Practice 8.4 Additive Manufacturing in Aircraft Maintenance

9 Chapter 9: Pipes, Flexible Hoses & Springs

9.1 Aircraft Rigid Tubing, Bending & 37-Degree Flaring Standards 9.2 Flexible Hoses, Installation Geometry & Serviceability 9.3 Aircraft Springs: Classifications, Rate Testing & Inspection

10 Chapter 10: Bearings & Mechanical Transmissions

10.1 Bearing Classifications, Load Types & Lubrication Practice 10.2 Bearing Defect Analysis: Spalling, Brinelling & Overheating 10.3 Gears, Gearboxes, Backlash Measurement & Belt/Chain Drives

11 Chapter 11: Flight Control Cables & Rigging

11.1 Aircraft Cable Construction, Sizing & Swaged Terminal Fittings 11.2 Cable Rigging, Turnbuckles & Temperature-Compensated Tensioning 11.3 Pulleys, Fairleads, Cable Inspection & Broken Strand Limits

12 Chapter 12: Aircraft Weight and Balance

12.1 Datum, Arm, Moment & Center of Gravity Principles 12.2 Aircraft Weighing Preparation, Equipment & Tare Deduction 12.3 Center of Gravity Calculations, Flight Limits & Ballast Adjustments

13 Chapter 13: Aircraft Handling, Storage & Winter Operations

13.1 Towing, Taxiing Protocols, Shear Pins & Wing Walkers 13.2 Jacking with Locking Collars, Chocking & Severe Weather Mooring 13.3 Ground De-icing and Anti-icing: Fluids, Clean Aircraft Concept & Holdover Times 13.4 Aircraft Parking, Protective Covers & Engine/Airframe Long-Term Preservation

14 Chapter 14: Inspection, Defect Assessment, Maintenance Procedures & Documentation

14.1 NDT Methods: Liquid Penetrant, Magnetic Particle, Eddy Current, Ultrasonic & Radiography 14.2 Corrosion Classifications, Mechanical Removal & Chemical Surface Treatments 14.3 Inspections After Lightning, Heavy Landing & Other Abnormal Events 14.4 Controlled Disassembly, Inspection & Reassembly 14.5 Troubleshooting, Defect Assessment & Repair Control 14.6 Maintenance Documentation, Work Reports & Shift Handover 14.7 Maintenance Planning, Stores Control, CRS & Occurrence Reporting

7.2 Rivet Spacing, Pitch, Edge Distance & Structural Layout

Key Takeaways Explain This Topic AI

Approved drawings or the SRM control rivet type, diameter, rows, pitch, edge distance, and repair geometry.

Common diameter-based ratios are useful learning and layout checks, not universal design limits.

Countersinking removes material and may require different thickness and edge controls from dimpling or protruding heads.

Lay out from stable datums, check hole quality and alignment, and do not relocate fasteners without approved data.

Last updated: September 2026

  • 7.2 Rivet Spacing, Pitch, Edge Distance & Structural Layout
  • Approved-Data Control

The figures and hardware examples in this section illustrate principles. For an actual aircraft or component, current approved maintenance data, product instructions, organisation procedures, and applicable law control the material, limit, interval, sequence, tooling, PPE, and acceptance decision.

A riveted joint is only as strong as its geometric layout. Merely selecting high-strength fasteners is insufficient; if rivets are placed too close to a sheet edge, the parent metal will tear out under tensile flight loads. Conversely, if rivets are spaced too far apart, the sheets will gap open, buckle under compressive stress, or trap corrosive moisture. To maintain structural airworthiness under EASA Part-66 Module 7, the aircraft maintenance engineer must master the mathematical rules governing Edge Distance (ED), pitch, transverse pitch, joint geometries (lap vs. butt joints), and fastener sizing calculations.

Fundamental Geometric Parameters of Riveted Joints

When designing or executing a structural sheet metal repair conforming to an Aircraft Maintenance Manual (AMM) or Structural Repair Manual (SRM), four geometric parameters dictate fastener placement: +-------------------------------------------------------------------------+

  • | RIVETED JOINT GEOMETRY PARAMETERS |
  • | |
  • | Sheet Edge |
  • | | |
  • | |<--- ED --->( + )<--------- Pitch --------->( + ) |
  • | | | | |
  • | | | | |
  • | | |<------- Transverse Pitch ---->| |
  • | | v v |
  • | |<--- ED --->( + )<--------- Pitch --------->( + ) |
  • | |
  • | D = Rivet Shank Diameter |
  • | ED = Edge Distance (Hole Centre to Sheet Edge) |
  • | Pitch = Centre-to-Centre Distance Between Rivets in Same Row |
  • | Transverse Pitch (Gauge) = Distance Between Parallel Rivet Rows |
  • +-------------------------------------------------------------------------+
  • 1. Edge Distance (ED)

Edge Distance is defined as the distance measured perpendicularly from the centre of the rivet hole to the nearest edge of the sheet metal .

Minimum Edge Distance:

Universal Head Rivets (MS20470): Minimum ED is 2 times the rivet shank diameter ( 2 D 2D 2 D ) .

Countersunk Head Rivets (MS20426): Minimum ED is 2.5 times the rivet shank diameter ( 2.5 D 2.5D 2.5 D ) .

Structural Rationale: Countersinking removes a conical volume of metal from the upper sheet, reducing the cylindrical bearing surface of the hole. A larger margin ( 2.5 D 2.5D 2.5 D ) is mandatory to prevent the fastener from tearing through the reduced sheet cross-section.

Defect Consequence: If ED is less than 2 D 2D 2 D (or 2.5 D 2.5D 2.5 D for flush), the joint suffers catastrophic shear tear-out (cleavage failure) , where the fastener rips through the edge of the sheet under design tensile loads.

Maximum Edge Distance:

Maximum allowable ED across all standard structural joints is 4 times the rivet shank diameter ( 4 D 4D 4 D ) .

Defect Consequence: If ED exceeds 4 D 4D 4 D , the sheet edge between fasteners is not held in intimate contact. The edge lifts and curls—a defect known as puckering . Moisture, de-icing fluid, and airborne dirt penetrate between the loose faying surfaces, initiating aggressive crevice corrosion, intergranular corrosion, and exfoliation.

2. Rivet Pitch (Spacing Along a Row)

Pitch is the linear distance measured between the centres of adjacent rivets in the same row .

Minimum Pitch: Must never be less than 3 times the shank diameter ( 3 D 3D 3 D ) .

Structural Rationale: Placing rivets closer than 3 D 3D 3 D concentrates stress fields around adjacent holes. Under load, these stress fields overlap, creating micro-cracks and causing the sheet to tear along the rivet line like a perforated postage stamp.

Standard Pitch: Standard aerospace design layout specifies a pitch between 4 D 4D 4 D and 6 D 6D 6 D (typically 4 D 4D 4 D to 5 D 5D 5 D for pressurized fuselage skins).

Maximum Pitch: The upper allowable limit for rivet pitch is 8 D 8D 8 D to 10 D 10D 10 D .

Defect Consequence: An excessive pitch allows thin skin panels to deflect, buckle, or "oil-can" between fasteners when subjected to aerodynamic shear or compression loads.

3. Transverse Pitch (Gauge / Distance Between Rows)

Transverse pitch—often termed row pitch or gauge—is the perpendicular distance measured between the centre lines of adjacent parallel rows of rivets .

Parallel (Square) Riveting: Minimum transverse pitch is 2.5 D 2.5D 2.5 D , with standard practice utilizing 3 D 3D 3 D to 4 D 4D 4 D .

Staggered (Zigzag) Riveting: When rivets are staggered between adjacent rows, the stress concentration is distributed more uniformly. The transverse pitch in staggered patterns is typically calculated as: Transverse Pitch (Staggered) = 0.75 × Pitch \text{Transverse Pitch (Staggered)} = 0.75 \times \text{Pitch} Transverse Pitch (Staggered) = 0.75 × Pitch

provided it does not fall below the absolute minimum of 2.5 D 2.5D 2.5 D .

Geometric Parameter Minimum Limit Standard Design Range Maximum Limit Primary Failure / Defect Risk

Edge Distance (Universal) 2.0 D 2.0D 2.0 D 2.0 D 2.0D 2.0 D – 2.5 D 2.5D 2.5 D 4.0 D 4.0D 4.0 D <2D: Sheet edge tear-out; >4D: Puckering & crevice corrosion

Edge Distance (Countersunk) 2.5 D 2.5D 2.5 D 2.5 D 2.5D 2.5 D – 3.0 D 3.0D 3.0 D 4.0 D 4.0D 4.0 D <2.5D: Knife-edge shear tear-out; >4D: Edge separation

Rivet Pitch (Along Row) 3.0 D 3.0D 3.0 D 4.0 D 4.0D 4.0 D – 6.0 D 6.0D 6.0 D 8.0 D 8.0D 8.0 D – 10.0 D 10.0D 10.0 D <3D: Sheet tearing along row; >10D: Skin buckling / oil-canning

Transverse Pitch (Parallel) 2.5 D 2.5D 2.5 D 3.0 D 3.0D 3.0 D – 4.0 D 4.0D 4.0 D — <2.5D: Inter-row stress concentration and shear failure

Transverse Pitch (Staggered) 2.5 D 2.5D 2.5 D 0.75 × Pitch 0.75 \times \text{Pitch} 0.75 × Pitch — Maintains uniform diagonal shear distribution

Joint Configurations: Lap Joints vs. Butt Joints

Aircraft structural skin and web splices are fabricated using either lap or butt joint configurations: Joint Configurations & Shear Loading:

  • Single-Row Lap Joint Double-Strap Butt Joint
  • (Eccentric Shear Loading) (Symmetrical Double Shear)
  • P <=== [ Sheet 1 ] [ Strap 1 ] ===> P/2
  • [=====] Rivet [=====] Rivet
  • [ Sheet 2 ] ===> P P <=== [ Sheet 1 ] [ Sheet 2 ] ===> P
  • [=====] Rivet
  • (Subject to secondary bending) [ Strap 2 ] ===> P/2
  • (Pure shear; zero bending moment)
  • Lap Joints

In a lap joint, the two sheets overlap directly and are secured by one or more rows of rivets. While simple to fabricate, lap joints are eccentrically loaded : because the tensile forces in the two sheets do not act along the same neutral plane, an internal couple (bending moment) is generated. This induces secondary bending, tilting the rivet heads and concentrating high peeling stresses along the sheet edges. Lap joints are restricted to light skins, secondary structures, or multi-row configurations designed to absorb secondary bending.

Butt Joints (Single and Double Strap)

In a butt joint, the two main sheets abut end-to-end along a straight seam:

Single-Strap Butt Joint: A single splice plate covers the abutting seam. Like the lap joint, it introduces an eccentric load path and secondary bending.

Double-Strap Butt Joint: Symmetrical splice plates are placed on both sides of the abutting sheets. The tensile load divides equally between the upper and lower straps ( P / 2 P/2 P /2 each), eliminating secondary bending. Crucially, each rivet operates in double shear —meaning the rivet shank must shear across two distinct planes before failure can occur. A rivet in double shear possesses approximately 1.75 to 2.0 times the load-carrying capacity of the same rivet in single shear. Double-strap butt joints are mandated for heavy-load primary structures, wing skin splices, and pressurized fuselage longitudinal seams.

Fastener Sizing Rules: Shank Diameter & Grip Length Calculations

When calculating fastener dimensions for a structural repair, two fundamental engineering rules dictate the rivet shank diameter and overall length.

1. The Rivet Shank Diameter Rule ( D ≈ 3 T D \approx 3T D ≈ 3 T )

To prevent an imbalance between fastener shear strength and parent sheet bearing strength: Rivet Shank Diameter ( D ) ≈ 3 × T \text{Rivet Shank Diameter } (D) \approx 3 \times T Rivet Shank Diameter ( D ) ≈ 3 × T

where T T T represents the thickness of the thickest sheet in the joint (or the single skin sheet in skin-to-doubler repairs).

Consequence of Undersized Rivet ( D < 2 T D < 2T D < 2 T ): The thin rivet shank lacks adequate shear cross-section; the joint fails prematurely via rivet shear fracture.

Consequence of Oversized Rivet ( D > 4 T D > 4T D > 4 T ): Driving an excessively large rivet requires massive bucking force. The high pressure deforms and stretches the thin sheet metal around the hole, causing puckering, hole distortion, and premature bearing failure of the sheet.

2. The Rivet Length Formula ( L = Grip + 1.5 D L = \text{Grip} + 1.5D L = Grip + 1.5 D )

The total length of a solid rivet must equal the total thickness of the material being joined plus sufficient protruding shank to form a standard, structurally airworthy shop head: Total Length ( L ) = Grip ( G ) + 1.5 D \text{Total Length } (L) = \text{Grip } (G) + 1.5D Total Length ( L ) = Grip ( G ) + 1.5 D

Grip ( G G G ): The total combined thickness of all sheets forming the joint.

1.5 D 1.5D 1.5 D Allowance: A length equal to 1.5 times the shank diameter must protrude beyond the sheets prior to driving. During upsetting, this protruding material collapses to form a standard shop head with a diameter of 1.5 D 1.5D 1.5 D and a height of 0.5 D 0.5D 0.5 D . Solid Rivet Length Sizing Geometry:

Manufactured Head

.---------------.

  • | |
  • '----+ +----'
  • ==============|=====|============== <-- Sheet 1
  • Total Grip (G)| | Combined Thickness
  • ==============|=====|============== <-- Sheet 2
  • | |
  • | | Protruding Allowance = 1.5D
  • '-----' (Forms 1.5D width x 0.5D height shop head)
  • Step-by-Step Practical Calculation Example

Problem: A certifying technician is repairing a damaged lower fuselage skin by installing an internal doubler plate. Both the skin and the doubler are fabricated from 0.040-inch (1.02 mm) 2024-T3 aluminium sheet. The repair calls for MS20470AD (universal head) rivets. Calculate the recommended rivet diameter and the exact rivet part number.

Determine Shank Diameter: D ≈ 3 × T = 3 × 0.040 " = 0.120 " D \approx 3 \times T = 3 \times 0.040" = 0.120" D ≈ 3 × T = 3 × 0.040" = 0.120"

The nearest standard aerospace rivet diameter in 32nds of an inch is 4/32" (1/8" or 0.125").

Therefore: Shank Diameter = 1/8" (0.125" = 4/32", Size 4) .

Calculate Total Grip: Grip ( G ) = T 1 + T 2 = 0.040 " + 0.040 " = 0.080 " \text{Grip } (G) = T_1 + T_2 = 0.040" + 0.040" = 0.080" Grip ( G ) = T 1 ​ + T 2 ​ = 0.040" + 0.040" = 0.080"

Calculate Shop Head Allowance ( 1.5 D 1.5D 1.5 D ): 1.5 D = 1.5 × 0.125 " = 0.1875 " 1.5D = 1.5 \times 0.125" = 0.1875" 1.5 D = 1.5 × 0.125" = 0.1875"

Calculate Total Rivet Length: L = G + 1.5 D = 0.080 " + 0.1875 " = 0.2675 " L = G + 1.5D = 0.080" + 0.1875" = 0.2675" L = G + 1.5 D = 0.080" + 0.1875" = 0.2675"

Convert to 16ths of an Inch: Length in 16ths = 0.2675 " × 16 = 4.28 \text{Length in 16ths} = 0.2675" \times 16 = 4.28 Length in 16ths = 0.2675" × 16 = 4.28

Since rivets are stocked in discrete 1/16" increments, round to the nearest standard length: a dash -4 (4/16" = 0.250") would leave the shop head slightly under-formed ( 0.250 " − 0.080 " = 0.170 " < 0.1875 " 0.250" - 0.080" = 0.170" < 0.1875" 0.250" − 0.080" = 0.170" < 0.1875" ), while a dash -5 (5/16" = 0.3125") provides 0.3125 " − 0.080 " = 0.2325 " 0.3125" - 0.080" = 0.2325" 0.3125" − 0.080" = 0.2325" . Per standard SRM grip charts, a total grip of 0.080" using a 1/8" rivet falls within the grip range for a dash -5 length (or a -4 if trimmed).

Complete Part Number: MS20470AD4-5 .

Hole Layout Tools & Cleco Fasteners

When fabricating repairs, holes must be transferred from the parent structure to replacement doublers with extreme accuracy.

Hole Duplicator (Hole Finder / Strap Duplicator): A flexible steel strap with an alignment pin on the lower leg and a drill bushing on the upper leg. The pin enters the existing parent hole behind the new sheet, centering the drill guide perfectly over the hidden hole.

Cleco Temporary Fasteners: Spring-loaded cylindrical clamps used to hold sheets in intimate alignment during drilling and riveting. Clecos are color-coded by diameter:

  • Silver: 3/32" (#40 hole)
  • Copper: 1/8" (#30 hole)
  • Black: 5/32" (#21 hole)
  • Brass (Gold): 3/16" (#10 hole)
  • Zinc / Green: 1/4" (1/4" hole)
  • Realistic Maintenance Scenario & Common Exam Traps
  • Realistic Maintenance Scenario

A certifying technician is performing a multi-row lap joint repair on a pressurized fuselage panel. The repair blueprint specifies 5/32" universal rivets with a 2-row staggered pattern. The blueprint lists the edge distance as 0.250 inches. Before drilling, the engineer performs a sanity check:

For a 5/32" (0.15625") universal rivet, the minimum allowable edge distance is 2 D = 2 × 0.15625 " = 0.3125 " 2D = 2 \times 0.15625" = 0.3125" 2 D = 2 × 0.15625" = 0.3125" (5/16"). The blueprint specification of 0.250" violates the mandatory minimum rule ( 0.250 " < 0.3125 " 0.250" < 0.3125" 0.250" < 0.3125" ). If drilled at 0.250", the sheet would tear out under cabin pressurization cycling. The engineer halts work, contacts structural engineering, and issues a Technical Variance to adjust the edge distance to 0.375" ( 2.4 D 2.4D 2.4 D ), maintaining airworthiness compliance.

Common Exam Traps

Trap 1: Measuring Edge Distance from the edge of the hole. Edge distance is ALWAYS measured from the centre line of the hole to the sheet edge , never from the hole perimeter.

Trap 2: Applying the 2D minimum edge distance rule to countersunk rivets. Universal head rivets require 2.0 D 2.0D 2.0 D , but countersunk rivets require a minimum of 2.5 D 2.5D 2.5 D due to the reduced bearing thickness from the conical cut.

Trap 3: Forgetting that double shear doubles fastener capacity. In a double-strap butt joint, rivets are loaded in double shear; a joint requiring 10 rivets in single shear only requires 5 to 6 rivets in double shear to carry the equivalent load.