Study guide

12.3 Center of Gravity Calculations, Flight Limits & Ballast Adjustments

EASA Part-66 Module 07 — Maintenance Practices Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Safety Precautions — Electricity, Gases & Chemical Hazards

1.1 Electrical-System Hazards, Isolation & Protective Equipment 1.2 Compressed Gases, Pressure Vessels & Oxygen System Safety 1.3 Hazardous Chemicals, Solvents, Oils & Personal Protective Equipment

2 Chapter 2: Safety Precautions — Fire Protection, Confined Spaces & Emergency Response

2.1 Fire Classifications, Extinguishing Agents & Asphyxiation Risks 2.2 Confined-Space Entry, Fuel-Tank Safety & CDCCL Control 2.3 Emergency Response, Accident Remediation & Ballistic Recovery Systems

3 Chapter 3: Workshop Practices, Hand Tools & Precision Measurement

3.1 Workshop Housekeeping, Tool Control & Foreign Object Debris (FOD) 3.2 Engineering Dimensions, Allowances & Tolerances 3.3 Hand Tools, Powered Equipment & Operating Safety 3.4 Precision Measuring Instruments & Standards Traceability

4 Chapter 4: Fastener Torquing & Avionic Test Equipment

4.1 Torque Wrenches, Extension Calculations & Calibration Care 4.2 Multimeters, Megohmmeters & Insulation Testing 4.3 Bonding Testers, Milliohmmeters & Oscilloscopes

5 Chapter 5: Engineering Drawings, Standards & Fits

5.1 Orthographic Projections, Title Blocks & Revision Control 5.2 Drawing Line Conventions, Symbols & ATA Specification 100/iSpec 2200 5.3 Electrical Schematics, Wiring Interconnects & Component Location 5.4 Systems of Limits, Fits, Clearances & Shaft Alignment

6 Chapter 6: Electrical Wiring Interconnection System (EWIS)

6.1 EWIS Principles, Wire Types & Loom Routing Practices 6.2 Crimp Terminations, Connector Pin Insertion & Extraction Tooling 6.3 Electrical Bonding, Grounding Resistance & Electromagnetic Shielding

7 Chapter 7: Aircraft Riveting Practice

7.1 Solid and Blind Rivet Classifications, Materials & Head Markings 7.2 Rivet Spacing, Pitch, Edge Distance & Structural Layout 7.3 Countersinking, Dimpling Techniques & Rivet Installation 7.4 Rivet Joint Inspection, Failure Modes & Drill-Out Procedures

8 Chapter 8: Sheet Metal Working & Composite Materials

8.1 Sheet Metal Forming, Neutral Axis & Bend Allowance Calculations 8.2 Welding, Brazing, Soldering & Structural Adhesive Bonding 8.3 Composite Reinforcements, Pre-Preg Cold Storage & Clean Room Practice 8.4 Additive Manufacturing in Aircraft Maintenance

9 Chapter 9: Pipes, Flexible Hoses & Springs

9.1 Aircraft Rigid Tubing, Bending & 37-Degree Flaring Standards 9.2 Flexible Hoses, Installation Geometry & Serviceability 9.3 Aircraft Springs: Classifications, Rate Testing & Inspection

10 Chapter 10: Bearings & Mechanical Transmissions

10.1 Bearing Classifications, Load Types & Lubrication Practice 10.2 Bearing Defect Analysis: Spalling, Brinelling & Overheating 10.3 Gears, Gearboxes, Backlash Measurement & Belt/Chain Drives

11 Chapter 11: Flight Control Cables & Rigging

11.1 Aircraft Cable Construction, Sizing & Swaged Terminal Fittings 11.2 Cable Rigging, Turnbuckles & Temperature-Compensated Tensioning 11.3 Pulleys, Fairleads, Cable Inspection & Broken Strand Limits

12 Chapter 12: Aircraft Weight and Balance

12.1 Datum, Arm, Moment & Center of Gravity Principles 12.2 Aircraft Weighing Preparation, Equipment & Tare Deduction 12.3 Center of Gravity Calculations, Flight Limits & Ballast Adjustments

13 Chapter 13: Aircraft Handling, Storage & Winter Operations

13.1 Towing, Taxiing Protocols, Shear Pins & Wing Walkers 13.2 Jacking with Locking Collars, Chocking & Severe Weather Mooring 13.3 Ground De-icing and Anti-icing: Fluids, Clean Aircraft Concept & Holdover Times 13.4 Aircraft Parking, Protective Covers & Engine/Airframe Long-Term Preservation

14 Chapter 14: Inspection, Defect Assessment, Maintenance Procedures & Documentation

14.1 NDT Methods: Liquid Penetrant, Magnetic Particle, Eddy Current, Ultrasonic & Radiography 14.2 Corrosion Classifications, Mechanical Removal & Chemical Surface Treatments 14.3 Inspections After Lightning, Heavy Landing & Other Abnormal Events 14.4 Controlled Disassembly, Inspection & Reassembly 14.5 Troubleshooting, Defect Assessment & Repair Control 14.6 Maintenance Documentation, Work Reports & Shift Handover 14.7 Maintenance Planning, Stores Control, CRS & Occurrence Reporting

12.3 Center of Gravity Calculations, Flight Limits & Ballast Adjustments

Key Takeaways Explain This Topic AI

Empty Weight Center of Gravity (EWCG) is derived from net scale reactions and known weighing point station arms using the fundamental principle of moments: CG = Total Moment / Total Empty Weight.

Operational weight regimes—Basic Empty Weight (BEW), Zero Fuel Weight (ZFW), Takeoff Weight (TOW), and Landing Weight (LW)—must each fall within certified forward and aft CG envelope limits throughout the flight profile.

Relocating mass longitudinally shifts the aircraft CG in the direction of the movement by a distance proportional to the ratio of shifted mass to total aircraft mass: Delta CG = (Weight Shifted × Distance Shifted) / Total Aircraft Weight.

When structural modifications or interior conversions push the empty CG outside approved flight limits, permanent or temporary ballast must be installed, calculated using the ballast formula: Ballast Weight = (Aircraft Weight × Desired CG Shift) / (Ballast Arm - Desired CG).

Every change to aircraft empty weight or CG requires immediate formal revision of the Weight and Balance Report, Equipment List, and Loading Schedule / Trim Sheet signed by an authorized Part-66 certifying engineer.

Last updated: September 2026

12.3 Center of Gravity Calculations, Flight Limits & Ballast Adjustments

Once an aircraft has been leveled, weighed, and tare deducted, the certifying maintenance engineer must convert raw net scale reactions into a certified Empty Weight Center of Gravity (EWCG) . Furthermore, the engineer must understand how subsequent equipment additions, component removals, and payload shifts alter the operational center of gravity across various flight phases. When modifications displace the center of gravity beyond certified airworthiness limits, mathematical ballast calculations must be executed to restore the aircraft to a compliant, airworthy condition.

Empty Weight Center of Gravity Derivation from Scale Reactions

To compute the longitudinal empty weight CG, the engineer establishes the horizontal arm from the reference datum to each weighing point. On a typical tricycle landing gear configuration, the weighing points are the nose gear and the main landing gear. TRICYCLE GEAR WEIGHING GEOMETRY

  • Datum
  • | CG
  • | Nose Arm |
  • |<----------------------------------->| Main Arm
  • | |<--------------------->|
  • +=============================================================+
  • | |
  • v v
  • [Nose Gear] [Main Gear]
  • Net = Wn Net = Wm
  • |<---------------- Wheelbase (D) --------->|
  • 1. The Moment Summation Method (Datum Forward of Aircraft)

When the reference datum is located forward of the nose, all arms are positive numbers: Total Empty Weight = W N + W M L + W M R \text{Total Empty Weight} = W_N + W_{ML} + W_{MR} Total Empty Weight = W N ​ + W M L ​ + W MR ​ Total Moment = ( W N × Arm N ) + ( W M L × Arm M L ) + ( W M R × Arm M R ) \text{Total Moment} = (W_N \times \text{Arm}_N) + (W_{ML} \times \text{Arm}_{ML}) + (W_{MR} \times \text{Arm}_{MR}) Total Moment = ( W N ​ × Arm N ​ ) + ( W M L ​ × Arm M L ​ ) + ( W MR ​ × Arm MR ​ ) CG Station = Total Moment Total Empty Weight \text{CG Station} = \frac{\text{Total Moment}}{\text{Total Empty Weight}} CG Station = Total Empty Weight Total Moment ​

Where:

  • Wn = Net weight on nose gear
  • Wml, Wmr = Net weight on left and right main gear
  • Arm_n, Arm_ml, Arm_mr = Horizontal station arms from reference datum to gear centerlines
  • 2. The Wheelbase Reaction Method (Datum at Main Gear Centerline)

If the datum is set at the main gear centerline, the main gear arm is zero (0.0). The CG distance forward of the main gear is derived directly from moment equilibrium: Distance from Main Gear to CG = W N × D Total Empty Weight \text{Distance from Main Gear to CG} = \frac{W_N \times D}{\text{Total Empty Weight}} Distance from Main Gear to CG = Total Empty Weight W N ​ × D ​

Where D is the horizontal distance between the nose gear and main gear (the wheelbase ). The CG station is then computed relative to the datum by adding or subtracting this distance.

Fully Worked Weighing & CG Calculation

A twin-turboprop commuter aircraft is weighed in an enclosed hangar following an avionics retrofit. The reference datum is located 100.0 inches forward of the fuselage nose tip. Leveling checks are verified. Tare is deducted. The recorded data is as follows:

  • Weighing Point Net Weight (kg) Station Arm from Datum (in) Moment (kg·in)
  • Nose Gear 1,450.0 180.0 1,450.0 × 180.0 = 261,000.0
  • Left Main Gear 3,120.0 450.0 3,120.0 × 450.0 = 1,404,000.0
  • Right Main Gear 3,130.0 450.0 3,130.0 × 450.0 = 1,408,500.0
  • TOTALS 7,700.0 kg — 3,073,500.0 kg·in

Computing the Empty Weight Center of Gravity: Empty Weight CG = 3 , 073 , 500.0 kg ⋅ in 7 , 700.0 kg = 399.16 inches \text{Empty Weight CG} = \frac{3,073,500.0\text{ kg}\cdot\text{in}}{7,700.0\text{ kg}} = \mathbf{399.16\text{ inches}} Empty Weight CG = 7 , 700.0 kg 3 , 073 , 500.0 kg ⋅ in ​ = 399.16 inches

If the certified Empty Weight CG range published in the TCDS is Station 395.0 to 403.0 inches , the calculated CG of 399.16 inches complies with airworthiness requirements.

Operational Weight Regimes & Flight Envelopes

An aircraft's weight and balance changes continuously during flight as fuel burns, passengers move, and payloads are dropped. Certifying engineers and flight dispatchers evaluate four distinct operational weight regimes: HIERARCHY OF AIRCRAFT WEIGHT REGIMES

  • +-------------------------------------------------------------------+
  • | Basic Empty Weight (BEW) [Structure, Engines, Unusable Fuel] |
  • +-------------------------------------------------------------------+
  • +
  • | Operating Items [Flight Crew, Galley Supplies, Manuals]|
  • +-------------------------------------------------------------------+
  • =
  • | Operating Empty Weight (OEW) |
  • +-------------------------------------------------------------------+
  • +
  • | Payload [Passengers, Baggage, Cargo] |
  • +-------------------------------------------------------------------+
  • =
  • | Zero Fuel Weight (ZFW) *** MUST NOT EXCEED MZFW LIMIT *** |
  • +-------------------------------------------------------------------+
  • +
  • | Takeoff Fuel [Usable Mission Fuel] |
  • +-------------------------------------------------------------------+
  • =
  • | Takeoff Weight (TOW) *** MUST NOT EXCEED MTOW LIMIT *** |
  • +-------------------------------------------------------------------+
  • | Trip Fuel Burn [Fuel Consumed in Flight] |
  • +-------------------------------------------------------------------+
  • =
  • | Landing Weight (LW) *** MUST NOT EXCEED MLW LIMIT *** |
  • +-------------------------------------------------------------------+
  • The Critical Significance of Maximum Zero Fuel Weight (MZFW)

The Maximum Zero Fuel Weight (MZFW) is the maximum certified weight of the aircraft loaded with crew, passengers, and payload, but with zero usable fuel in the tanks.

Structural Rationale (Wing Root Bending Relief): In flight, upward aerodynamic lift acts on the wings, exerting immense upward bending moments at the wing roots (where the wings join the fuselage). Fuel stored in wing tanks acts as a downward dead weight, partially offsetting and relieving this upward bending stress. Fuselage payload (passengers and cargo), however, acts directly downward on the fuselage, increasing wing root bending stress. Restricting the total fuselage weight via the MZFW ensures that wing root structural spars are never overstressed in the event the aircraft burns all its wing fuel down to empty.

Alterations: Weight Shifts, Additions & Removals

Maintenance activities frequently involve removing obsolete equipment, installing modern components, or rearranging cabin seats and cargo compartments.

1. Weight Shift Formula

When an existing mass onboard the aircraft is moved from one longitudinal location to another, the total aircraft weight remains unchanged, but the center of gravity shifts in the direction of the movement: Δ CG = Weight Shifted × Distance Shifted Total Aircraft Weight \Delta \text{CG} = \frac{\text{Weight Shifted} \times \text{Distance Shifted}}{\text{Total Aircraft Weight}} Δ CG = Total Aircraft Weight Weight Shifted × Distance Shifted ​ New CG = Original CG ± Δ CG \text{New CG} = \text{Original CG} \pm \Delta \text{CG} New CG = Original CG ± Δ CG

2. Equipment Addition or Removal Formula

When equipment is permanently added to or removed from the aircraft, both the total aircraft weight and total moment change: New CG = Original Total Moment ± ( Added or Removed Weight × Arm ) Original Total Weight ± Added or Removed Weight \text{New CG} = \frac{\text{Original Total Moment} \pm (\text{Added or Removed Weight} \times \text{Arm})}{\text{Original Total Weight} \pm \text{Added or Removed Weight}} New CG = Original Total Weight ± Added or Removed Weight Original Total Moment ± ( Added or Removed Weight × Arm ) ​

Rule: Add weight and moment when installing equipment; subtract weight and moment when removing equipment.

Worked Example: Equipment Removal & Installation

An aircraft with an empty weight of 5,000 kg and an empty CG at Station 120.0 inches (Original Moment = 5,000 × 120.0 = 600,000 kg·in) undergoes an avionics upgrade:

An old navigation unit weighing 30 kg located at Station 40.0 inches is removed :

Removed Moment = 30 × 40.0 = 1,200 kg·in

A modern digital multi-function display weighing 10 kg is installed at Station 50.0 inches :

Added Moment = 10 × 50.0 = 500 kg·in New Total Weight = 5 , 000 − 30 + 10 = 4 , 980 kg \text{New Total Weight} = 5,000 - 30 + 10 = \mathbf{4,980\text{ kg}} New Total Weight = 5 , 000 − 30 + 10 = 4 , 980 kg New Total Moment = 600 , 000 − 1 , 200 + 500 = 599 , 300 kg ⋅ in \text{New Total Moment} = 600,000 - 1,200 + 500 = \mathbf{599,300\text{ kg}\cdot\text{in}} New Total Moment = 600 , 000 − 1 , 200 + 500 = 599 , 300 kg ⋅ in New CG = 599 , 300 4 , 980 = 120.34 inches \text{New CG} = \frac{599,300}{4,980} = \mathbf{120.34\text{ inches}} New CG = 4 , 980 599 , 300 ​ = 120.34 inches

The removal of the net 20 kg from the forward nose bay shifted the aircraft center of gravity slightly aft, from Station 120.00 inches to Station 120.34 inches.

Ballast Calculations & Structural Installation Standards

When structural repairs, equipment retrofits, or mission configurations displace the aircraft empty or operating CG beyond certified boundaries, ballast must be installed to bring the CG back into the approved envelope.

Mathematical Derivation of Ballast

To determine the exact ballast weight required to shift an aircraft CG from its current out-of-limits position to a desired target position within the envelope: Ballast Weight = Aircraft Weight × Desired CG Shift Ballast Arm − Desired CG Station \text{Ballast Weight} = \frac{\text{Aircraft Weight} \times \text{Desired CG Shift}}{\text{Ballast Arm} - \text{Desired CG Station}} Ballast Weight = Ballast Arm − Desired CG Station Aircraft Weight × Desired CG Shift ​

Where:

  • Aircraft Weight = Weight prior to adding ballast
  • Desired CG Shift = Absolute difference between Current CG and Desired Target CG
  • Ballast Arm = Station arm where ballast will be physically mounted
  • Desired CG Station = Target station location of the new center of gravity
  • Worked Ballast Calculation

An aircraft weighing 4,500 kg has its center of gravity at Station 88.0 inches . Due to heavy avionics removals in the nose, the CG has moved aft of the certified aft limit of Station 86.0 inches by 2.0 inches. The maintenance facility plans to install permanent ballast in the forward avionics bay at Station 20.0 inches to shift the CG forward to exactly the aft limit of Station 86.0 inches .

Identify variables:

  • Aircraft Weight = 4,500 kg
  • Current CG = 88.0 inches
  • Desired CG = 86.0 inches
  • Desired Shift = 88.0 - 86.0 = 2.0 inches
  • Ballast Arm = 20.0 inches

Apply the ballast formula: Ballast Weight = 4 , 500 × 2.0 86.0 − 20.0 = 9 , 000 66.0 = 136.36 kg \text{Ballast Weight} = \frac{4,500 \times 2.0}{86.0 - 20.0} = \frac{9,000}{66.0} = \mathbf{136.36\text{ kg}} Ballast Weight = 86.0 − 20.0 4 , 500 × 2.0 ​ = 66.0 9 , 000 ​ = 136.36 kg

Verification Check:

  • Original Moment = 4,500 × 88.0 = 396,000 kg·in
  • Ballast Moment = 136.36 × 20.0 = 2,727.2 kg·in
  • Total Moment = 396,000 + 2,727.2 = 398,727.2 kg·in
  • Total Weight = 4,500 + 136.36 = 4,636.36 kg

New CG = 398,727.2 / 4,636.36 = 86.00 inches (Matches the target exactly).

Airframe Installation Standards for Ballast

Permanent Ballast: Typically fabricated from high-density lead plates, steel bars, or depleted uranium/tungsten blocks. It must be bolted securely to primary structural members (such as fuselage bulkheads, longerons, or engine mount trusses) using certified AN/MS aerospace bolts, large load-distribution washers, and positive self-locking nuts or cotter-pinned castellated nuts. It must be clearly painted in bright red or yellow gloss paint and stenciled with durable lettering: P E R M A N E N T B A L L A S T − − − D O N O T R E M O V E − − − [ W E I G H T ] K G \mathbf{PERMANENT\;BALLAST\;---\;DO\;NOT\;REMOVE\;---\;[WEIGHT]\;KG} PERMANENT BALLAST − − − DO NOT REMOVE − − − [ WEIGHT ] KG

Temporary Ballast: Carried in cargo holds or baggage bays for specific light-payload flights. Must be secured with certified cargo tie-down straps or cargo nets capable of withstanding certified emergency landing forward and vertical G-loadings. It must be explicitly tagged and logged on the flight load manifest.

Weight & Balance Documentation, Equipment List & Legal Sign-Off

Under EASA Part-66 and Part-M/Part-ML, any weighing or weight-and-balance alteration must be legally documented before the aircraft can be released to service:

Weight and Balance Report: An official engineering document recording the date and location of weighing, scale types and calibration dates, hangar ambient conditions, leveling means used, tare deductions, net reaction weights, calculated empty weight, and calculated EWCG.

Equipment List: A comprehensive inventory itemizing every piece of equipment included in the basic empty weight. Each entry specifies part number, description, manufacturer, serial number, mass, and station arm. Items are categorized as 'X' (Installed) or 'O' (Optional/Removed). When an engineer adds or removes an LRU, the Equipment List must be marked up and re-dated.

Loading Schedule / Trim Sheet: Operational charts or electronic flight bag (EFB) software algorithms enabling pilots and loadmasters to verify that payload, passenger seating, and fuel loading remain within the certified flight envelope across all stages of flight.

Certificate of Release to Service (CRS): An authorized Part-66 aircraft maintenance engineer must sign a CRS entering the new empty weight and EWCG into the aircraft technical logbook and updating the Aircraft Flight Manual (AFM) Weight and Balance Supplement.

  • Realistic Maintenance Scenario & Common Exam Traps
  • Realistic Maintenance Scenario

A certifying Part-66 engineer is supervising the cabin reconfiguration of a corporate transport. Ten luxury passenger seats (weighing 25 kg each at Station 300) are removed, and a high-density configuration of sixteen commuter seats (weighing 18 kg each at Station 280) is installed. The engineer updates the weight and balance ledger by deducting 250 kg at Station 300 (-75,000 kg·in) and adding 288 kg at Station 280 (+80,640 kg·in). The net change (+38 kg and +5,640 kg·in) is added into the master empty weight report, and the equipment list is revised with new part numbers and serial numbers prior to CRS issuance.

Common Exam Traps

Trap 1: Forgetting that ballast adds to total aircraft mass. In ballast calculations, the ballast weight increases both the moment and the total mass of the aircraft. Forgetting to include the ballast mass in the denominator when verifying the new CG is a frequent calculation error.

Trap 2: Misunderstanding Zero Fuel Weight. Many technicians mistakenly assume that if Takeoff Weight is below Maximum Takeoff Weight, the aircraft is safe. If the cabin is overloaded with cargo beyond the MZFW limit, the wing root spars can fail in flight even if the aircraft is under its Maximum Takeoff Weight.

Trap 3: Subtracting instead of adding moved weight in the shift formula. Moving weight aft ALWAYS shifts CG aft; moving weight forward ALWAYS shifts CG forward. Always perform a quick common-sense sanity check on your mathematical signs.