Study guide
10.3 Gears, Gearboxes, Backlash Measurement & Belt/Chain Drives
EASA Part-66 Module 07 — Maintenance Practices Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Safety Precautions — Electricity, Gases & Chemical Hazards
1.1 Electrical-System Hazards, Isolation & Protective Equipment 1.2 Compressed Gases, Pressure Vessels & Oxygen System Safety 1.3 Hazardous Chemicals, Solvents, Oils & Personal Protective Equipment
2 Chapter 2: Safety Precautions — Fire Protection, Confined Spaces & Emergency Response
2.1 Fire Classifications, Extinguishing Agents & Asphyxiation Risks 2.2 Confined-Space Entry, Fuel-Tank Safety & CDCCL Control 2.3 Emergency Response, Accident Remediation & Ballistic Recovery Systems
3 Chapter 3: Workshop Practices, Hand Tools & Precision Measurement
3.1 Workshop Housekeeping, Tool Control & Foreign Object Debris (FOD) 3.2 Engineering Dimensions, Allowances & Tolerances 3.3 Hand Tools, Powered Equipment & Operating Safety 3.4 Precision Measuring Instruments & Standards Traceability
4 Chapter 4: Fastener Torquing & Avionic Test Equipment
4.1 Torque Wrenches, Extension Calculations & Calibration Care 4.2 Multimeters, Megohmmeters & Insulation Testing 4.3 Bonding Testers, Milliohmmeters & Oscilloscopes
5 Chapter 5: Engineering Drawings, Standards & Fits
5.1 Orthographic Projections, Title Blocks & Revision Control 5.2 Drawing Line Conventions, Symbols & ATA Specification 100/iSpec 2200 5.3 Electrical Schematics, Wiring Interconnects & Component Location 5.4 Systems of Limits, Fits, Clearances & Shaft Alignment
6 Chapter 6: Electrical Wiring Interconnection System (EWIS)
6.1 EWIS Principles, Wire Types & Loom Routing Practices 6.2 Crimp Terminations, Connector Pin Insertion & Extraction Tooling 6.3 Electrical Bonding, Grounding Resistance & Electromagnetic Shielding
7 Chapter 7: Aircraft Riveting Practice
7.1 Solid and Blind Rivet Classifications, Materials & Head Markings 7.2 Rivet Spacing, Pitch, Edge Distance & Structural Layout 7.3 Countersinking, Dimpling Techniques & Rivet Installation 7.4 Rivet Joint Inspection, Failure Modes & Drill-Out Procedures
8 Chapter 8: Sheet Metal Working & Composite Materials
8.1 Sheet Metal Forming, Neutral Axis & Bend Allowance Calculations 8.2 Welding, Brazing, Soldering & Structural Adhesive Bonding 8.3 Composite Reinforcements, Pre-Preg Cold Storage & Clean Room Practice 8.4 Additive Manufacturing in Aircraft Maintenance
9 Chapter 9: Pipes, Flexible Hoses & Springs
9.1 Aircraft Rigid Tubing, Bending & 37-Degree Flaring Standards 9.2 Flexible Hoses, Installation Geometry & Serviceability 9.3 Aircraft Springs: Classifications, Rate Testing & Inspection
10 Chapter 10: Bearings & Mechanical Transmissions
10.1 Bearing Classifications, Load Types & Lubrication Practice 10.2 Bearing Defect Analysis: Spalling, Brinelling & Overheating 10.3 Gears, Gearboxes, Backlash Measurement & Belt/Chain Drives
11 Chapter 11: Flight Control Cables & Rigging
11.1 Aircraft Cable Construction, Sizing & Swaged Terminal Fittings 11.2 Cable Rigging, Turnbuckles & Temperature-Compensated Tensioning 11.3 Pulleys, Fairleads, Cable Inspection & Broken Strand Limits
12 Chapter 12: Aircraft Weight and Balance
12.1 Datum, Arm, Moment & Center of Gravity Principles 12.2 Aircraft Weighing Preparation, Equipment & Tare Deduction 12.3 Center of Gravity Calculations, Flight Limits & Ballast Adjustments
13 Chapter 13: Aircraft Handling, Storage & Winter Operations
13.1 Towing, Taxiing Protocols, Shear Pins & Wing Walkers 13.2 Jacking with Locking Collars, Chocking & Severe Weather Mooring 13.3 Ground De-icing and Anti-icing: Fluids, Clean Aircraft Concept & Holdover Times 13.4 Aircraft Parking, Protective Covers & Engine/Airframe Long-Term Preservation
14 Chapter 14: Inspection, Defect Assessment, Maintenance Procedures & Documentation
14.1 NDT Methods: Liquid Penetrant, Magnetic Particle, Eddy Current, Ultrasonic & Radiography 14.2 Corrosion Classifications, Mechanical Removal & Chemical Surface Treatments 14.3 Inspections After Lightning, Heavy Landing & Other Abnormal Events 14.4 Controlled Disassembly, Inspection & Reassembly 14.5 Troubleshooting, Defect Assessment & Repair Control 14.6 Maintenance Documentation, Work Reports & Shift Handover 14.7 Maintenance Planning, Stores Control, CRS & Occurrence Reporting
10.3 Gears, Gearboxes, Backlash Measurement & Belt/Chain Drives
Key Takeaways Explain This Topic AI
Gear type, ratio, direction, thrust, tooth contact, backlash, and lubrication are evaluated for the actual transmission design.
Backlash and contact-pattern limits come from approved data and are measured at stated positions and conditions.
Belt and chain tension, alignment, wear, and elongation are system-specific and require the prescribed tools and limits.
After assembly, restore locking and guards and complete required rotation, lubrication, and functional checks.
Last updated: September 2026
- 10.3 Gears, Gearboxes, Backlash Measurement & Belt/Chain Drives
- Approved-Data Control
Values and examples explain principles. Current approved maintenance data, product instructions, organisation procedures, and applicable law control actual limits, materials, intervals, methods, and acceptance.
Mechanical transmission systems are vital aircraft subsystems engineered to transfer rotational power, transform speed and torque, and redirect mechanical drive vectors across aircraft components. In aviation applications—such as turboprop reduction gearboxes converting 40,000 RPM turbine shaft speed down to 1,200 RPM propeller speed, helicopter main rotor transmissions transmitting thousands of horsepower at 90° angles, and flight control mechanical actuators—transmissions must operate with near-total mechanical reliability under severe cyclic stresses. The EASA Part-66 maintenance engineer must master gear geometries, planetary epicyclic reduction physics, backlash measurement protocols, tooth meshing patterns, and belt and chain drive maintenance.
Aircraft Gear Types, Tooth Geometries & Thrust Vectors
Aircraft gears are manufactured from case-hardened alloy steels (such as nickel-chromium-molybdenum AISI 9310 or nitriding steels like Nitralloy 135M) with precision-ground tooth profiles conforming to an involute curve . The involute profile ensures a constant angular velocity ratio between mating gears throughout engagement.
1. Spur Gears
Geometry: Teeth are cut straight and parallel to the axis of rotation on cylindrical gear blanks. Meshing occurs across parallel shafts.
Operational Dynamics: Tooth engagement occurs instantaneously across the entire face width of the tooth simultaneously. This sudden application of load generates high impact noise, vibrational harmonics, and dynamic contact stress at high pitch-line velocities. However, spur gears operate with the highest mechanical efficiency (98% to 99%) and generate zero axial thrust load along the shaft.
Applications: Engine accessory gearbox starter gear trains, fuel pump drive idlers, and flight deck manual trim control dials.
2. Helical Gears
Geometry: Teeth are cut at an angle across the face of the cylindrical blank, forming a helix inclined at a helix angle ( β \beta β , typically 15° to 30°). Meshing occurs between parallel shafts.
Operational Dynamics: Teeth engage progressively, starting as a point at one side of the tooth edge and smoothly rolling into full line contact across the face. This gradual engagement produces smooth, quiet operation with significantly higher load-carrying capacity than spur gears.
The Axial Thrust Penalty: Because the tooth contact line is inclined at an angle β \beta β , the normal tooth load resolves into two force components: a tangential driving force and a significant axial thrust force ( F t h r u s t = F t a n g e n t i a l × tan β F_{thrust} = F_{tangential} \times \tan \beta F t h r u s t = F t an g e n t ia l × tan β ) that pushes the gear along its shaft. Helical gear shafts must be equipped with dedicated thrust bearings (e.g., angular contact ball bearings or tapered rollers) to absorb this longitudinal vector.
Applications: High-speed turbine engine accessory drives, turboprop primary reduction stages, and helicopter intermediate gearboxes.
3. Double Helical & Herringbone Gears
Geometry: Features two sets of helical teeth cut on the same gear blank with identical helix angles but in opposite directions (left-hand and right-hand helixes). In a true herringbone gear , the two helix tracks meet seamlessly at a center apex without a groove; in double-helical gears, a narrow clearance groove separates them for manufacturing tool runout.
Axial Thrust Cancellation: Because the two helix tracks have equal and opposite angles, they generate equal and opposite axial thrust forces. These forces cancel each other out internally within the gear blank ( F n e t _ t h r u s t = 0 F_{net\_thrust} = 0 F n e t _ t h r u s t = 0 ).
Operational Value: Herringbone gears combine the smooth, quiet, high-torque capabilities of helical teeth with the zero-thrust advantage of spur gears, eliminating the weight and friction of heavy thrust bearings.
Applications: High-power main turboprop propeller reduction gearboxes (e.g., Rolls-Royce Tyne, Europrop TP400) and heavy marine gas turbine marine reduction units. +-------------------------------------------------------------------------+
- | AIRCRAFT GEAR TYPES & THRUST VECTORS |
- | |
- | 1. SPUR GEAR 2. HELICAL GEAR |
- | Teeth parallel to axis Teeth cut at helix angle (beta) |
- | Parallel shafts Parallel shafts |
- | Thrust Vector: ZERO Thrust Vector: HEAVY AXIAL |
- | |
- | |||||||||| \\\\\\\\ |
- | |||||||||| \\\\\\\\ |
- | Shaft <======> Shaft Shaft <======> Shaft ---> F_ax |
- | |
- | 3. HERRINGBONE (Double Helical) 4. SPIRAL BEVEL GEAR |
- | Opposing helix tracks Intersecting shafts (90°) |
- | Parallel shafts Curved teeth, high torque |
- | Thrust Vector: ZERO (Cancelled) Thrust Vector: Heavy Axial/Radial|
- | |
- | <<<<<<<<<< / / / |
- | >>>>>>>>>> | | | 90° Drive |
- | Shaft <======> Shaft \ \ \ |
- +-------------------------------------------------------------------------+
- 4. Bevel Gears (Straight, Spiral & Hypoid)
Straight Bevel Gears: Conical gear blanks with straight teeth tapering toward the cone apex. Designed to transmit power across intersecting shafts (typically at a 90° right angle). Like spur gears, teeth engage abruptly, limiting their speed.
Spiral Bevel Gears: Conical blanks with curved, oblique spiral teeth. Meshing is gradual and progressive, yielding high strength, smooth power delivery, and quiet operation under severe loads. Used in helicopter 90° main rotor mast gearboxes, tail rotor intermediate/tail gearboxes, and jet engine radial tower shafts driving accessory gearboxes from the high-pressure spool.
Hypoid Gears: Resemble spiral bevel gears, but the driving pinion shaft does not intersect the gear axis (the pinion shaft is offset either above or below the center of the ring gear). This offset allows shafts to cross without touching. Meshing involves a complex combination of rolling and longitudinal sliding contact, requiring specialized Extreme Pressure (EP) sulfur-phosphorus lubricants. Used in specialized helicopter tail rotor drive drop-boxes and auxiliary drives.
5. Worm and Worm Wheel (Worm Drive)
Geometry: Consists of a cylindrical screw with helical spiral threads (the worm ) meshing with a concave-toothed spur gear (the worm wheel ). The axes are non-intersecting and oriented at 90° to each other.
Characteristics: Provides massive speed reduction ratios in a single stage (typically 20:1 up to 70:1) within an extremely compact space. Contact involves severe sliding friction, resulting in lower mechanical efficiency (60% to 85%) and requiring high-viscosity synthetic compounded lubricants.
The Irreversible (Self-Locking) Anti-Backdrive Feature: When the lead angle of the worm is shallow (typically < 5 ∘ < 5^\circ < 5 ∘ to 6 ∘ 6^\circ 6 ∘ ), the coefficient of static friction exceeds the tangent of the lead angle. Under this condition, the worm can easily drive the worm wheel, but the worm wheel cannot back-drive the worm . Any torque applied to the output wheel jams against the worm threads.
Aviation Applications: Essential safety mechanism in aircraft flap drive power units, horizontal stabilizer trim tab actuators, landing gear emergency manual crank winches, and cargo door hoist drives. If electrical or hydraulic motor drive power is lost, the self-locking worm drive prevents aerodynamic air loads from back-driving and blowing out the control surfaces.
Gear Type Shaft Relationship Tooth Profile Axial Thrust Generated Mechanical Efficiency Primary Aircraft System
Spur Parallel Straight Zero Very High (98%–99%) Accessory gearbox idler drives, fuel pump gearheads
Helical Parallel Angled Helix High (mandates thrust bearing) High (96%–98%) High-speed turbine accessory reduction stages
Herringbone Parallel Opposed Double Helix Zero (forces cancel) Very High (97%–99%) High-power turboprop main reduction gearboxes
Straight Bevel Intersecting (90°) Straight Taper Moderate High (95%–97%) Low-speed flap interconnect 90° gearboxes
Spiral Bevel Intersecting (90°) Curved Spiral High (Axial & Radial) High (96%–98%) Turbine radial tower shaft, helicopter main/tail rotor gearboxes
Hypoid Non-Intersecting (Offset) Curved Hyperboloid High (requires EP oil) Medium (90%–94%) Rotorcraft tail rotor offset drive gearboxes
Worm Drive Non-Intersecting (90°) Screw / Concave Wheel High Axial Medium (60%–85%) Flap actuators, stabilizer trim tabs (anti-backdrive)
Epicyclic (Planetary) Gear Systems
In high-power aircraft transmissions, conventional single-stage parallel gear trains are too large and heavy to achieve the necessary speed reduction. Epicyclic (planetary) gearboxes solve this by distributing torque across multiple load paths within a compact, coaxial housing. +-------------------------------------------------------------------------+
- | EPICYCLIC (PLANETARY) GEAR ARCHITECTURE |
- | |
- | [ Ring Gear / Annulus ] |
- | .-----------------. |
- | / (Internally) \ |
- | | (Toothed) | |
- | | .---. .---. | |
- | | ( P_1 ) ( P_2 ) | <-- Planet Gears (P) |
- | | '---' '---' | |
- | | .-. .-. | |
- | | ( Sun ) | <-- Sun Gear (S) |
- | | '-' '-' | (High-Speed Input) |
- | | .---. .---. | |
- | | ( P_3 ) ( P_4 ) | |
- | | '---' '---' | |
- | \ [Planet Carrier]/ |
- | '-----------------' |
- | |
- | Standard Reduction Setup (Turboprop / Helicopter): |
- | - Annulus (Ring) is FIXED to gearbox case. |
- | - Sun Gear is high-speed INPUT. |
- | - Planet Carrier is low-speed, high-torque OUTPUT. |
- | - Ratio: R = 1 + (N_annulus / N_sun) |
- +-------------------------------------------------------------------------+
- Structural Components
An epicyclic gear train consists of four concentric elements:
Sun Gear ( S S S ): The central external-toothed gear rotating on the primary centerline axis. Typically driven by the high-speed turbine shaft.
Planet Gears ( P P P ): Three to five identical external-toothed gears spaced symmetrically around the sun gear and meshing simultaneously with both the sun and outer ring gear.
Planet Carrier ( C C C ): The structural cage holding the planet gear shafts. As the planet gears orbit the sun gear, the carrier rotates on the main centerline axis.
Ring Gear / Annulus ( A A A ): The outer internal-toothed ring enclosing the entire assembly.
Coaxial Architecture Advantages
Pure Coaxial Alignment: The input shaft and output shaft share the exact same centerline axis, eliminating bending moments on the casing and minimizing nacelle frontal area.
Multiple Load Paths: Torque from the sun gear is divided equally across 3, 4, or 5 planet gears. This reduces gear tooth bending stresses by 66% to 80% compared to a two-gear countershaft arrangement, enabling dramatic weight savings.
Reduction Ratio Calculation (Fixed-Annulus Mode)
In standard turboprop propeller reduction and helicopter main rotor gearboxes, the Ring Gear (Annulus) is held stationary (fixed to the gearbox casing) . The Sun Gear is the high-speed input, and the Planet Carrier is the low-speed, high-torque output: Reduction Ratio ( R ) = Input Speed ( N s u n ) Output Speed ( N c a r r i e r ) = 1 + N a n n u l u s N s u n \text{Reduction Ratio } (R) = \frac{\text{Input Speed } (N_{sun})}{\text{Output Speed } (N_{carrier})} = 1 + \frac{N_{annulus}}{N_{sun}} Reduction Ratio ( R ) = Output Speed ( N c a rr i er ) Input Speed ( N s u n ) = 1 + N s u n N ann u l u s
where N a n n u l u s N_{annulus} N ann u l u s is the number of teeth on the internal ring gear, and N s u n N_{sun} N s u n is the number of teeth on the sun gear. WORKSHOP CALCULATION EXAMPLE:
A turboprop reduction gearbox epicyclic stage has a Sun Gear with 24 teeth (N_sun = 24)
and a fixed Annulus Gear with 96 teeth (N_annulus = 96).
Step 1: Calculate the Stage Speed Reduction Ratio (R):
R = 1 + (N_annulus / N_sun) = 1 + (96 / 24) = 1 + 4 = 5.0 : 1
- Step 2: If the gas generator turbine drives the Sun Gear at 11,000 RPM with an input
- torque of 300 Nm, calculate the Planet Carrier propeller output speed and torque
(assuming 98% mechanical efficiency):
- Output Propeller Speed = N_sun / R = 11,000 RPM / 5.0 = 2,200 RPM
- Ideal Output Torque = Input Torque x R = 300 Nm x 5.0 = 1,500 Nm
- Actual Output Torque = 1,500 Nm x 0.98 = 1,470 Nm
- Backlash: Definition, Purpose & Measurement Protocols
- Definition & Purpose of Backlash
Backlash is the circumferential clearance (play) between the non-driving tooth flanks of mating gear teeth when measured at the pitch circle circle.
Why Backlash is Mandatory:
Accommodates Thermal Expansion: As gearboxes reach operating temperatures (up to 120°C in flight), steel gear teeth expand radially and circumferentially. Without backlash, thermal expansion would wedge mating teeth tightly together, causing immediate tooth binding and seizure.
Ensures Lubricant Entry: Backlash allows space for an elastohydrodynamic (EHL) oil film to enter and coat the non-driving flanks, preventing metal-to-metal welding and tooth scuffing.
Absorbs Tolerances: Compensates for allowable shaft runout, housing machining variations, and center-distance tolerances.
The DTI Measurement Procedure (Primary Standard)
To measure backlash in an assembled gearbox, the technician uses a Dial Test Indicator (DTI) :
Mount the DTI rigidly to the gearbox casing using a magnetic base or mechanical clamp.
Lock the driving gear stationary using a soft wooden wedge, copper clamp, or shaft holding fixture so that it cannot rotate.
Position the spherical stylus of the DTI exactly perpendicular (at 90°) to the face of a tooth on the driven gear at the pitch circle radius.
Zero the dial indicator bezel.
Gently rock the driven gear back and forth by hand through its free rotational clearance without moving the locked driving gear.
Read the total needle sweep on the dial indicator. This value represents the actual circumferential backlash.
Repeat the measurement at three or four positions spaced 90° apart around the gear circumference to detect gear eccentricity or shaft runout. Compare against the Component Maintenance Manual (CMM) allowable limits (typically 0.003" to 0.008" / 0.08 mm to 0.20 mm ). +-------------------------------------------------------------------------+
- | BACKLASH MEASUREMENT SETUP WITH DTI |
- | |
- | [ Dial Test Indicator (DTI) ] |
- | [0.000"] |
- | || |
- | || Stylus perpendicular |
- | v to tooth flank at pitch line |
- | .--------. / |
- | / Tooth \/ |
- | [Mating Gear]| Driven | <-- Rock driven gear back |
- | LOCKED FIRM | Gear | and forth gently by hand |
- | ===============\__________/ |
- | |
- | Criteria: Total DTI needle deflection = Circumferential Backlash. |
- | Check at 4 positions (90° apart) to detect pitch circle runout. |
- +-------------------------------------------------------------------------+
- Alternative Measurement: Feeler Gauge
On large, open-access industrial or test-rig spur gear sets where a DTI cannot be positioned, precision leaf feeler gauges may be inserted between the non-driving tooth flanks at the mesh point. However, in aviation gearboxes, the DTI method is the mandated standard because feeler gauges can bridge uneven tooth wear or introduce angular error.
Operational Hazards of Incorrect Backlash
Excessive Backlash: Generates violent dynamic gear chatter and tooth rattling, particularly during torque reversals. Under pulsating engine loads, excessive play causes impact hammer shock loading on tooth flanks, initiating severe root bending fatigue and tooth breakage.
Insufficient Backlash: As operating temperatures rise, thermal expansion eliminates the clearance gap. Tooth flanks squeeze out the lubricating oil film, resulting in rapid micro-welding, intense scuffing, severe galling, tooth face pitting, and catastrophic transmission lockup.
Tooth Contact Pattern Inspection (Prussian Blue Dye)
Measuring backlash verifies clearance, but it does not confirm whether gear teeth are meshing correctly across their full working face. To verify alignment, technicians perform a tooth contact pattern inspection using Prussian blue engineer's marking compound.
Workshop Procedure
Thoroughly degrease the gear teeth with approved solvent and wipe dry.
Apply a micro-thin, uniform film of Prussian blue paste to both drive and coast flanks of three or four consecutive teeth on the driving gear.
Rotate the gear train by hand through mesh several complete revolutions against a light resisting brake load applied to the driven shaft (simulating operational tooth contact pressure).
Inspect the pattern transferred to the uncoated teeth of the mating gear. +-------------------------------------------------------------------------+
- | GEAR TOOTH CONTACT PATTERNS |
- | |
- | 1. CORRECT PATTERN (Centered on Pitch Line) |
- | .-------------------------------------------------. |
- | | Top Land | |
- | | .-----------------------------. | |
- | | | UNIFORM CONTACT (50%-75%) | | Pitch Line |
- | | '-----------------------------' | |
- | | Root Dedendum | |
- | '-------------------------------------------------' |
- | Toe (Inner Edge) Heel (Outer Edge) |
- | |
- | 2. INCORRECT: HEEL CONTACT 3. INCORRECT: TOE CONTACT |
- | .-----------------------. .-----------------------. |
- | | [ CONTACT]| |[CONTACT] | |
- | '-----------------------' '-----------------------' |
- | Causes: Shaft deflection, Causes: Over-shimming, |
- | excessive gear offset. misaligned bearing bore. |
- +-------------------------------------------------------------------------+
- Contact Pattern Interpretation
Ideal Pattern: Centered evenly between top land and root dedendum, extending across approximately 50% to 75% of the central face width , with a gentle fade toward both the toe (inner edge) and heel (outer edge). On spiral bevel gears, unloaded test patterns are intentionally biased slightly toward the toe ; under high engine torque, shaft deflection moves the contact zone into the exact center of the tooth.
Heel Contact (Heavy Outer Edge): Tooth contact concentrated at the wide outer edge. Indicates excessive shaft deflection or improper axial shimming of bevel gears.
Toe Contact (Heavy Inner Edge): Contact concentrated at the narrow inner edge. Causes severe edge stress concentrations, leading to corner chipping.
Flank (Root) or Face (Tip) Contact: Indicates incorrect center distance between shafts or improper tooth profile cutting depth.
Mechanical Belt & Chain Transmission Drives
Where rotational power must be transmitted across significant center distances without the weight of an intermediate gear train, belt and chain drives are deployed.
1. Synchronous (Toothed) Timing Belts
Construction: Molded neoprene rubber or polyurethane reinforced with continuous internal longitudinal tensile cords of Kevlar, carbon fiber, or high-tensile fiberglass. The inner surface features molded transverse trapezoidal or curvilinear teeth.
Operational Principle: Operates via positive mechanical engagement between belt teeth and grooved pulley sprockets. Provides zero slip , maintaining absolute rotational synchronism between shafts.
Applications: Flight Data Recorder (FDR) drives, engine electronic governor position feedbacks, camera gimbal stabilization drives, and cockpit trim tab indicator transmitters.
2. V-Belt Drives
Construction: Continuous loop of rubber and fabric cords with a trapezoidal (V-shaped) cross section. Operates in matching V-groove sheaves.
Operating Principle: Wedging action of the belt into the pulley sheave multiplies normal contact force, providing high tractive friction without excessive belt tension. Permits slight slip under shock loads, protecting driven accessories.
Applications: Alternator and cooling blower fan drives on light piston aircraft engines.
3. Roller Chain Drives
Construction: Precision steel assemblies conforming to ANSI B29.1 or British Standards (BS 228). Comprises alternating inner link plates with press-fit bushings and outer link plates with press-fit pins, enclosed by free-rotating hardened steel rollers.
Applications: Primary flight control cable-to-surface bellcrank connections, aileron and rudder trim systems, flap synchronization torque shafts, and manual landing gear emergency extension drives.
Critical Maintenance Checks:
Chain Tension & Deflection: Measured mid-span between sprockets. The total allowable slack deflection is typically 1/64 inch per inch of span under a calibrated thumb or spring-balance load.
Sprocket Alignment: Sprocket faces must be verified parallel and coplanar using a precision straight-edge or laser alignment tool to prevent roller side-plate wear.
Elongation Wear Limit (The 2% to 3% Rule): Chains do not "stretch" elastically in service; they elongate due to mechanical wear and material loss at the internal pin-and-bushing interfaces. The engineer measures the length of a specified span of links (e.g., 20 pitch lengths) with a vernier caliper while applying tension. If the measured pitch elongation exceeds 2% to 3% of the original nominal pitch length , the chain must be rejected and scrapped. An elongated chain rides up on the sprocket tooth tips, causing tooth skipping and catastrophic chain breakage.
- Realistic Maintenance Scenario & Common Exam Traps
- Realistic Maintenance Scenario
A licensed maintenance engineer is reassembling an intermediate 90° tail rotor gearbox on a light twin-turbine helicopter following seal replacement. The gearbox houses a spiral bevel driving pinion and driven gear.
Backlash Measurement: The engineer locks the pinion shaft with an approved spline holding tool. A DTI is clamped to the magnesium case with its stylus positioned perpendicular to the driven gear tooth face at the pitch line. Rocking the driven gear yields a DTI sweep of 0.009 inches. The CMM allowable backlash specification is 0.004" to 0.007".
Shim Adjustment: Because backlash is excessive (0.009"), the engineer calculates the required shim adjustment. Removing a 0.003" laminated stainless steel shim from behind the driven bevel gear bearing carrier moves the gear closer into mesh with the pinion.
Re-measurement: Re-checking with the DTI at four 90° quadrants yields 0.005", 0.005", 0.006", and 0.005", perfectly within the 0.004" to 0.007" CMM limit.
Tooth Contact Verification: The engineer cleans the teeth and applies a thin film of Prussian blue dye to three pinion teeth. Rotating the assembly against hand brake drag produces a clean, centered contact pattern extending across 60% of the tooth face, slightly biased toward the toe. The gearbox is approved for closure and safety-wired.
Common Exam Traps
Trap 1: Believing helical gears produce zero axial thrust. Helical gears generate substantial axial thrust forces that push gears along their shaft; only double helical (herringbone) gears cancel axial thrust internally.
Trap 2: Miscalculating fixed-annulus epicyclic gear ratios. Remember the formula is R = 1 + ( N a n n u l u s / N s u n ) R = 1 + (N_{annulus} / N_{sun}) R = 1 + ( N ann u l u s / N s u n ) . Forgetting the " 1 + 1 + 1 + " is a very common exam calculation error.
Trap 3: Measuring backlash parallel to the gear face. Dial indicator styluses must be placed strictly perpendicular (90°) to the tooth flank at the pitch line. Angled positioning introduces cosine measurement error, giving false backlash readings.
Trap 4: Attributing chain elongation to metal stretching. Roller chains elongate due to pin and bushing wear, not elastic stretching of the link plates. Exceeding 2% to 3% elongation mandates replacement.