Study guide
5.1 Orthographic Projections, Title Blocks & Revision Control
EASA Part-66 Module 07 — Maintenance Practices Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Safety Precautions — Electricity, Gases & Chemical Hazards
1.1 Electrical-System Hazards, Isolation & Protective Equipment 1.2 Compressed Gases, Pressure Vessels & Oxygen System Safety 1.3 Hazardous Chemicals, Solvents, Oils & Personal Protective Equipment
2 Chapter 2: Safety Precautions — Fire Protection, Confined Spaces & Emergency Response
2.1 Fire Classifications, Extinguishing Agents & Asphyxiation Risks 2.2 Confined-Space Entry, Fuel-Tank Safety & CDCCL Control 2.3 Emergency Response, Accident Remediation & Ballistic Recovery Systems
3 Chapter 3: Workshop Practices, Hand Tools & Precision Measurement
3.1 Workshop Housekeeping, Tool Control & Foreign Object Debris (FOD) 3.2 Engineering Dimensions, Allowances & Tolerances 3.3 Hand Tools, Powered Equipment & Operating Safety 3.4 Precision Measuring Instruments & Standards Traceability
4 Chapter 4: Fastener Torquing & Avionic Test Equipment
4.1 Torque Wrenches, Extension Calculations & Calibration Care 4.2 Multimeters, Megohmmeters & Insulation Testing 4.3 Bonding Testers, Milliohmmeters & Oscilloscopes
5 Chapter 5: Engineering Drawings, Standards & Fits
5.1 Orthographic Projections, Title Blocks & Revision Control 5.2 Drawing Line Conventions, Symbols & ATA Specification 100/iSpec 2200 5.3 Electrical Schematics, Wiring Interconnects & Component Location 5.4 Systems of Limits, Fits, Clearances & Shaft Alignment
6 Chapter 6: Electrical Wiring Interconnection System (EWIS)
6.1 EWIS Principles, Wire Types & Loom Routing Practices 6.2 Crimp Terminations, Connector Pin Insertion & Extraction Tooling 6.3 Electrical Bonding, Grounding Resistance & Electromagnetic Shielding
7 Chapter 7: Aircraft Riveting Practice
7.1 Solid and Blind Rivet Classifications, Materials & Head Markings 7.2 Rivet Spacing, Pitch, Edge Distance & Structural Layout 7.3 Countersinking, Dimpling Techniques & Rivet Installation 7.4 Rivet Joint Inspection, Failure Modes & Drill-Out Procedures
8 Chapter 8: Sheet Metal Working & Composite Materials
8.1 Sheet Metal Forming, Neutral Axis & Bend Allowance Calculations 8.2 Welding, Brazing, Soldering & Structural Adhesive Bonding 8.3 Composite Reinforcements, Pre-Preg Cold Storage & Clean Room Practice 8.4 Additive Manufacturing in Aircraft Maintenance
9 Chapter 9: Pipes, Flexible Hoses & Springs
9.1 Aircraft Rigid Tubing, Bending & 37-Degree Flaring Standards 9.2 Flexible Hoses, Installation Geometry & Serviceability 9.3 Aircraft Springs: Classifications, Rate Testing & Inspection
10 Chapter 10: Bearings & Mechanical Transmissions
10.1 Bearing Classifications, Load Types & Lubrication Practice 10.2 Bearing Defect Analysis: Spalling, Brinelling & Overheating 10.3 Gears, Gearboxes, Backlash Measurement & Belt/Chain Drives
11 Chapter 11: Flight Control Cables & Rigging
11.1 Aircraft Cable Construction, Sizing & Swaged Terminal Fittings 11.2 Cable Rigging, Turnbuckles & Temperature-Compensated Tensioning 11.3 Pulleys, Fairleads, Cable Inspection & Broken Strand Limits
12 Chapter 12: Aircraft Weight and Balance
12.1 Datum, Arm, Moment & Center of Gravity Principles 12.2 Aircraft Weighing Preparation, Equipment & Tare Deduction 12.3 Center of Gravity Calculations, Flight Limits & Ballast Adjustments
13 Chapter 13: Aircraft Handling, Storage & Winter Operations
13.1 Towing, Taxiing Protocols, Shear Pins & Wing Walkers 13.2 Jacking with Locking Collars, Chocking & Severe Weather Mooring 13.3 Ground De-icing and Anti-icing: Fluids, Clean Aircraft Concept & Holdover Times 13.4 Aircraft Parking, Protective Covers & Engine/Airframe Long-Term Preservation
14 Chapter 14: Inspection, Defect Assessment, Maintenance Procedures & Documentation
14.1 NDT Methods: Liquid Penetrant, Magnetic Particle, Eddy Current, Ultrasonic & Radiography 14.2 Corrosion Classifications, Mechanical Removal & Chemical Surface Treatments 14.3 Inspections After Lightning, Heavy Landing & Other Abnormal Events 14.4 Controlled Disassembly, Inspection & Reassembly 14.5 Troubleshooting, Defect Assessment & Repair Control 14.6 Maintenance Documentation, Work Reports & Shift Handover 14.7 Maintenance Planning, Stores Control, CRS & Occurrence Reporting
5.1 Orthographic Projections, Title Blocks & Revision Control
Key Takeaways Explain This Topic AI
First-angle projection positions the object between observer and projection plane (plan view placed below elevation), whereas third-angle projection positions the projection plane between observer and object (plan view placed above elevation).
The ISO projection symbol uses a truncated cone (frustum); first-angle displays the concentric circles on the side opposite the cone taper, while third-angle places the concentric circles adjacent to the small end.
Pictorial drawing methods include isometric projection (axes inclined at 30° to horizontal, equal foreshortening) and oblique projection (front face true shape, receding axis at 30° or 45° foreshortened in cabinet projection).
Drawing revision blocks track engineering changes sequentially using revision letters that strictly omit I, O, Q, S, X, and Z to prevent misidentification with numerical digits.
Last updated: September 2026
- 5.1 Orthographic Projections, Title Blocks & Revision Control
- Approved-Data Control
The figures and hardware examples in this section illustrate principles. For an actual aircraft or component, current approved maintenance data, product instructions, organisation procedures, and applicable law control the material, limit, interval, sequence, tooling, PPE, and acceptance decision.
In aeronautical engineering and aircraft maintenance, engineering drawings are legal, technical instruments that define the exact physical geometry, material specifications, and assembly tolerances of airframe structures and systems. A licensed maintenance engineer must interpret multi-view orthographic drawings with absolute precision. Misinterpreting a projection method or misreading a title block tolerance can lead to manufacturing inverted components, installing structural brackets backward, or applying incorrect torque and clearance values, compromising aircraft airworthiness.
Principles of Orthographic Projection
Orthographic projection is a technique for representing a three-dimensional object in two dimensions by projecting parallel, perpendicular visual rays (projectors) from the object onto orthogonal planes of projection. Standard engineering drawings employ three primary mutually perpendicular planes:
Frontal Plane (Vertical Plane): Yields the Front Elevation (Front View), chosen to display the most characteristic contours and primary dimensions of the component.
Horizontal Plane: Yields the Plan View (Top View), viewed from directly above the object.
Profile Plane: Yields the Side Elevation (Left-Side or Right-Side View), viewed along the transverse axis. FIRST-ANGLE PROJECTION THIRD-ANGLE PROJECTION
(European Standard - ISO) (US Standard - ANSI)
- [ Observer ] [ Observer ]
- |
- v |
- +--------------+ v
- | OBJECT | ==================== (Plane)
- +--------------+ |
- | v
- v +--------------+
- ==================== (Plane) | OBJECT |
- +--------------+
- Object between observer & plane. - Plane between observer & object.
- Rays project THROUGH object. - Object viewed through TRANSPARENT plane.
- Plan view placed UNDER elevation. - Plan view placed ABOVE elevation.
- Left view placed on RIGHT side. - Left view placed on LEFT side.
First-Angle Projection (European / ISO Standard)
In First-Angle Projection (traditionally used throughout Europe and standardized under ISO 128):
The component is placed in the first quadrant , positioned between the observer and the projection plane.
The observer looks through the object onto the plane behind it.
Plan View (Top View): The observer looks down from the top, projecting the view downward onto the horizontal plane situated underneath the Front Elevation .
Left-Side View: The observer looks at the left face of the object, projecting the image across to the profile plane on the right. Consequently, the Left-Side View is drawn to the right of the Front Elevation .
Right-Side View: Viewed from the right and projected onto the left, positioned to the left of the Front Elevation .
Bottom View: Viewed from below and projected onto the upper plane, drawn above the Front Elevation .
Third-Angle Projection (US / ANSI Standard)
In Third-Angle Projection (the standard across North American aviation manufacturing, ASME Y14.3, and widely used in modern aerospace):
The component is placed in the third quadrant , where the projection plane is situated between the observer and the object.
The projection planes are treated as transparent sheets.
Plan View (Top View): The observer looks down through the horizontal plane at the object below. The resulting Plan View is placed directly above the Front Elevation .
Left-Side View: The observer looks through the left profile plane at the left face of the object. The Left-Side View is positioned directly on the left of the Front Elevation .
Right-Side View: Drawn on the right of the Front Elevation .
Bottom View: Drawn directly underneath the Front Elevation .
Comparison of Orthographic Projection Systems
- Feature First-Angle Projection (ISO) Third-Angle Projection (ANSI / ASME)
- Quadrant Placement First Quadrant Third Quadrant
- Spatial Relationship Observer -> Object -> Projection Plane Observer -> Projection Plane -> Object
- Plan View Location Directly below Front Elevation Directly above Front Elevation
- Left-Side View Location Positioned to the right of Front Elevation Positioned to the left of Front Elevation
- Right-Side View Location Positioned to the left of Front Elevation Positioned to the right of Front Elevation
- Bottom View Location Positioned above Front Elevation Positioned below Front Elevation
- Regional Prevalence United Kingdom, Continental Europe, ISO United States, Canada, Global Aerospace
- Official ISO Projection Cone Symbols
Because an engineering drawing may originate from an American airframe manufacturer (Boeing, third-angle) or a European consortium (Airbus, first-angle), drawings must explicitly state the projection method in or near the title block using standardized symbols based on a truncated cone (frustum) . FIRST-ANGLE PROJECTION SYMBOL (ISO)
- +------+
- | | (( O ))
- | +----+ / o \
- | | | | * |
- | +----+ \ o /
- | | (( O ))
- +------+
- [ Frustum: Large base [ Concentric circles on right,
- at left, small at right ] projected through object ]
- THIRD-ANGLE PROJECTION SYMBOL (ANSI)
- +------+
- (( O )) | |
- / o \ +----+ |
- | * | | | |
- \ o / +----+ |
- (( O )) | |
- +------+
- [ Concentric circles on [ Frustum: Small base facing left,
- left, viewed directly ] large base facing right ]
- Deciphering the Symbol Geometry
The symbol consists of two views of a truncated cone lying horizontally on its side:
First-Angle Symbol: Shows the frustum of the cone with its larger base to the left and tapered small base to the right. The second view consists of two concentric circles representing the two circular ends. In first-angle, viewing the cone from the left projects the small end onto the plane behind it on the right; thus, the concentric circles appear on the right of the frustum .
Third-Angle Symbol: Shows the concentric circles positioned on the left of the frustum . The observer looks at the small end of the cone from the left, viewing it through the intervening projection plane.
Pictorial Drawing Systems: Isometric, Oblique & Perspective
While orthographic multi-view drawings are the primary medium for manufacturing, pictorial drawings provide three-dimensional visualization in Illustrated Parts Catalogs (IPC) and maintenance manuals. ISOMETRIC VIEW (120° Spacing) OBLIQUE (CABINET) VIEW
- Z (Vertical) Y (Vertical)
- | |
- | | / Z (Receding 45°)
- | | / (Half Scale: 1:2)
- +----------- X +----------- X
- / \ (Front face true shape)
- / \ 30°
- / \
- / \
- v v
- Y (30° to Horiz) X (30° to Horiz)
- 1. Isometric Projection
Axis Geometry: Constructed around three principal axes spaced exactly 120° apart . The vertical axis represents height, while two receding axes are inclined at 30° to the horizontal baseline .
Dimensional Scaling: Because lines recede from the observer, true isometric projection foreshortens lines along the isometric axes to approximately 81.6% (square root of 2/3) of their actual length. However, standard workshop practice uses an isometric drawing , where full 1:1 scale is measured directly along the 30° axes.
Parallelism & Contours: Lines parallel on the physical object remain parallel on the isometric drawing. Non-isometric lines (slanted surfaces) cannot be measured directly; their endpoints must be plotted from coordinate reference points on isometric axes.
Circles: Circles lying on isometric planes deform into ellipses and are typically drawn using the four-centre approximation method.
2. Oblique Projection
Axis Geometry: The front face of the component is positioned parallel to the projection plane. The horizontal and vertical axes form a standard 90° angle, while the third axis (depth) recedes at an angle—typically 45° (or 30°/60°).
Front Face Fidelity: Because the front face is parallel to the drawing sheet, all circles, arcs, and intricate profiles on this face are drawn in their true shape and true dimensions without elliptical distortion.
Cavalier vs. Cabinet Oblique:
Cavalier Oblique: Dimensions along the receding axis are drawn at full scale (1:1) . This produces visual distortion, making the object appear unnaturally elongated.
Cabinet Oblique: Dimensions along the receding axis are foreshortened to half scale (1:2) . This compensates for optical perspective and provides a realistic appearance.
3. Perspective Projection
Visual rays converge toward one or more vanishing points on a horizon line, replicating how the human eye or camera perceives depth.
Limitation in Maintenance: Parallel lines converge, and identical physical dimensions scale down with distance. Consequently, perspective drawings cannot be scaled or measured for workshop fabrication or repair layout.
Engineering Drawing Layout & Title Block Data
Every certified aircraft engineering drawing contains a standardized layout governed by ISO 7200 or BS 8888. The Title Block is located in the lower right-hand corner of the drawing sheet so that it remains visible when the drawing is folded according to standard archiving procedures. +-----------------------------------------------------------------------------+
- | [ZONE A1] [ZONE A8] |
- | |
- | DRAWING FIELD |
- | (Orthographic Views) |
- | |
- | +----------------------------+
- | | REVISION BLOCK | REV C |
- | | ECO-48912 | 2026-04-12 | CR|
- | +----------------------------+
- | | TITLE BLOCK |
- | | P/N: 204-011-402-001 |
- | | TITLE: WING RIB ATTACH LUG |
- | [ZONE H1] | SCALE: 1:1 | SHT 1 OF 2 |
- +------------------------------------------------+----------------------------+
- Title Block Critical Fields Checklist
Drawing Number & Part Number: The primary alphanumeric identifier under configuration control. The drawing number identifies the document; the part number (P/N) identifies the physical hardware item.
Drawing Title: A concise description of the part or assembly (e.g., BRACKET - FLAP ACTUATOR SUPPORT, INBOARD).
Scale: The ratio of the drawn image size to the true physical object size:
Full Size (1:1): One unit on the drawing equals one unit on the part.
Enlarged Scale (2:1, 5:1, 10:1): Used for miniature gears, electrical contacts, and instrument needles.
Reduced Scale (1:2, 1:5, 1:10, 1:50): Used for large wing spars, fuselage bulkheads, and structural skins.
Not to Scale (NTS): Explicit warning indicating dimensions must be read numerically and never scaled with a rule.
Drawing Sheet Sizing: Standardized sheet sizes ensure uniform storage:
ISO 216 A Series: Halving the sheet along its long edge yields the next size, maintaining an aspect ratio of 1 to square root of 2:
- A0: 841 x 1189 mm (1.0 square metre area)
- A1: 594 x 841 mm
- A2: 420 x 594 mm
- A3: 297 x 420 mm
- A4: 210 x 297 mm (standard technical manual page)
ANSI / ASME Y14.1 Sizes: ANSI A (8.5 x 11 in), ANSI B (11 x 17 in), ANSI C (17 x 22 in), ANSI D (22 x 34 in), ANSI E (34 x 44 in).
Material Specification: Identifies exact aerospace metallurgy (e.g., AL 2024-T351 PER AMS-QQ-A-250/4 or STEEL 4130 PER MIL-S-6758).
Heat Treatment & Surface Finish: Specifies protective treatments (e.g., HEAT TREAT TO CONDITION T6; SULPHURIC ACID ANODIZE PER MIL-A-8625 TYPE II CLASS 1; EPOXY PRIMER PER BMS 10-11).
General Tolerances Block: Establishes default permissible variations for any dimension lacking a specific callout:
Linear: X.X = ±0.5 mm; X.XX = ±0.10 mm; X.XXX = ±0.025 mm
Angular: ±0.5° (or ±0°30').
Drawing Coordinate Zone System
Large engineering drawings (such as airframe structural blueprints and electrical harness fold-outs) feature an alphanumeric grid border resembling map coordinates:
Vertical Margins: Divided into lettered zones from top to bottom ( A, B, C, D, E, F, G, H ).
Horizontal Margins: Divided into numbered zones from right to left (or left to right) ( 1, 2, 3, 4, 5, 6, 7, 8 ).
When an Engineering Order (EO) or Service Bulletin notes that a fastener hole diameter has changed at Zone C4 , the maintenance technician locates row C and column 4 to find the exact callout on a multi-metre blueprint within seconds.
Drawing Revision Control & Engineering Change Protocols
Aircraft undergo continuous modifications throughout their multi-decade operating lifespans. The Revision Block (usually positioned in the upper-right corner of the drawing) records every approved engineering modification.
Revision Block Structure
Revision Letter: Tracks configuration changes sequentially (Initial Release = - , followed by Rev A , Rev B , etc.).
Standard Aviation Revision Rule: The letters I, O, Q, S, X, and Z are strictly omitted from revision tracking. This prevents confusion with numbers: I resembles 1 , O and Q resemble 0 , S resembles 5 , X represents a dimension multiplier, and Z resembles 2 .
Description of Change: Concise explanation of the alteration (e.g., HOLE DIA CHANGED FROM 6.35 TO 7.94 MM TO ACCOMMODATE OVERSIZE BUSHING).
Engineering Authority: Engineering Order (EO), Engineering Change Proposal (ECP), or Service Bulletin (SB) number.
Signatures & Dates: Sign-offs by the draftsman, stress analysis engineer, metallurgical checker, and airworthiness authority liaison. +-----------------------------------------------------------------------------+
- | REVISION HISTORY |
- +-----+----------------------------------+------------+------------+----------+
- | REV | DESCRIPTION | ECP / EO | DATE | APPROVED |
- +-----+----------------------------------+------------+------------+----------+
- | - | INITIAL PRODUCTION RELEASE | EO-10024 | 2024-03-15 | J.K. |
- | A | DRAIN HOLE ADDED AT FLANGE BASE | EO-11450 | 2024-11-02 | M.T. |
- | B | BUSHING I.D. REVISED TO H7 FIT | EO-12890 | 2025-06-20 | R.C. |
- | C | MATERIAL UPDATED TO 7075-T7351 | EO-14205 | 2026-02-18 | P.L. |
- +-----+----------------------------------+------------+------------+----------+
- Realistic Maintenance Scenario: Structural Modification Verification
An aircraft technician is tasked with installing a stiffener angle on an engine nacelle bulkhead per a Service Bulletin modification. The technician pulls drawing P/N 53-120-405 from the technical library.
Revision Audit: The SB mandates installation per Drawing 53-120-405 Revision D . The drawing printed on the workbench shows Revision B . Installing parts according to Revision B violates airworthiness control, as Revision D may include altered edge distances or additional fatigue-relief fastener holes.
Projection Check: The technician checks the title block projection symbol. It displays third-angle projection. Consequently, the view drawn directly to the left of the main bulkhead profile represents the left flange, not the right flange.
Zone Navigation: The task card specifies: Relocate grounding stud per Zone E6 . The technician traces vertical zone E across to horizontal zone 6 , immediately locating the revised coordinate callout.
Common Exam Traps & Pitfalls
Exam Trap 1: Reversing view positions between first-angle and third-angle projections. Remember: in first-angle projection, the plan view is underneath the front elevation (the observer looks from above and projects down onto the floor). In third-angle projection, the plan view is above the front elevation (the observer looks through the glass ceiling).
Exam Trap 2: Misidentifying projection cone symbols. If the concentric circles are on the right of the frustum whose small end points right, it is first-angle . If the concentric circles are on the left adjacent to the small end, it is third-angle .
Exam Trap 3: Forgetting omitted revision letters. Examination questions frequently ask which sequence of revision letters is valid. Any sequence containing I, O, Q, S, X, or Z is invalid under aerospace drafting standards.