Study guide

2.2 Confined-Space Entry, Fuel-Tank Safety & CDCCL Control

EASA Part-66 Module 07 — Maintenance Practices Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Safety Precautions — Electricity, Gases & Chemical Hazards

1.1 Electrical-System Hazards, Isolation & Protective Equipment 1.2 Compressed Gases, Pressure Vessels & Oxygen System Safety 1.3 Hazardous Chemicals, Solvents, Oils & Personal Protective Equipment

2 Chapter 2: Safety Precautions — Fire Protection, Confined Spaces & Emergency Response

2.1 Fire Classifications, Extinguishing Agents & Asphyxiation Risks 2.2 Confined-Space Entry, Fuel-Tank Safety & CDCCL Control 2.3 Emergency Response, Accident Remediation & Ballistic Recovery Systems

3 Chapter 3: Workshop Practices, Hand Tools & Precision Measurement

3.1 Workshop Housekeeping, Tool Control & Foreign Object Debris (FOD) 3.2 Engineering Dimensions, Allowances & Tolerances 3.3 Hand Tools, Powered Equipment & Operating Safety 3.4 Precision Measuring Instruments & Standards Traceability

4 Chapter 4: Fastener Torquing & Avionic Test Equipment

4.1 Torque Wrenches, Extension Calculations & Calibration Care 4.2 Multimeters, Megohmmeters & Insulation Testing 4.3 Bonding Testers, Milliohmmeters & Oscilloscopes

5 Chapter 5: Engineering Drawings, Standards & Fits

5.1 Orthographic Projections, Title Blocks & Revision Control 5.2 Drawing Line Conventions, Symbols & ATA Specification 100/iSpec 2200 5.3 Electrical Schematics, Wiring Interconnects & Component Location 5.4 Systems of Limits, Fits, Clearances & Shaft Alignment

6 Chapter 6: Electrical Wiring Interconnection System (EWIS)

6.1 EWIS Principles, Wire Types & Loom Routing Practices 6.2 Crimp Terminations, Connector Pin Insertion & Extraction Tooling 6.3 Electrical Bonding, Grounding Resistance & Electromagnetic Shielding

7 Chapter 7: Aircraft Riveting Practice

7.1 Solid and Blind Rivet Classifications, Materials & Head Markings 7.2 Rivet Spacing, Pitch, Edge Distance & Structural Layout 7.3 Countersinking, Dimpling Techniques & Rivet Installation 7.4 Rivet Joint Inspection, Failure Modes & Drill-Out Procedures

8 Chapter 8: Sheet Metal Working & Composite Materials

8.1 Sheet Metal Forming, Neutral Axis & Bend Allowance Calculations 8.2 Welding, Brazing, Soldering & Structural Adhesive Bonding 8.3 Composite Reinforcements, Pre-Preg Cold Storage & Clean Room Practice 8.4 Additive Manufacturing in Aircraft Maintenance

9 Chapter 9: Pipes, Flexible Hoses & Springs

9.1 Aircraft Rigid Tubing, Bending & 37-Degree Flaring Standards 9.2 Flexible Hoses, Installation Geometry & Serviceability 9.3 Aircraft Springs: Classifications, Rate Testing & Inspection

10 Chapter 10: Bearings & Mechanical Transmissions

10.1 Bearing Classifications, Load Types & Lubrication Practice 10.2 Bearing Defect Analysis: Spalling, Brinelling & Overheating 10.3 Gears, Gearboxes, Backlash Measurement & Belt/Chain Drives

11 Chapter 11: Flight Control Cables & Rigging

11.1 Aircraft Cable Construction, Sizing & Swaged Terminal Fittings 11.2 Cable Rigging, Turnbuckles & Temperature-Compensated Tensioning 11.3 Pulleys, Fairleads, Cable Inspection & Broken Strand Limits

12 Chapter 12: Aircraft Weight and Balance

12.1 Datum, Arm, Moment & Center of Gravity Principles 12.2 Aircraft Weighing Preparation, Equipment & Tare Deduction 12.3 Center of Gravity Calculations, Flight Limits & Ballast Adjustments

13 Chapter 13: Aircraft Handling, Storage & Winter Operations

13.1 Towing, Taxiing Protocols, Shear Pins & Wing Walkers 13.2 Jacking with Locking Collars, Chocking & Severe Weather Mooring 13.3 Ground De-icing and Anti-icing: Fluids, Clean Aircraft Concept & Holdover Times 13.4 Aircraft Parking, Protective Covers & Engine/Airframe Long-Term Preservation

14 Chapter 14: Inspection, Defect Assessment, Maintenance Procedures & Documentation

14.1 NDT Methods: Liquid Penetrant, Magnetic Particle, Eddy Current, Ultrasonic & Radiography 14.2 Corrosion Classifications, Mechanical Removal & Chemical Surface Treatments 14.3 Inspections After Lightning, Heavy Landing & Other Abnormal Events 14.4 Controlled Disassembly, Inspection & Reassembly 14.5 Troubleshooting, Defect Assessment & Repair Control 14.6 Maintenance Documentation, Work Reports & Shift Handover 14.7 Maintenance Planning, Stores Control, CRS & Occurrence Reporting

2.2 Confined-Space Entry, Fuel-Tank Safety & CDCCL Control

Key Takeaways Explain This Topic AI

Fuel-tank entry is a controlled confined-space task requiring an authorised plan, atmosphere testing, ventilation, communications, standby support, and a practicable rescue arrangement.

Atmospheric acceptance limits and test frequency come from the applicable entry procedure; a single initial reading does not control a changing atmosphere.

Ignition sources must be controlled through approved lighting, tools, bonding, equipment positioning, and hot-work restrictions.

CDCCLs preserve fuel-tank ignition-prevention features and may not be changed without the approved design process.

The standby attendant monitors and summons the planned rescue response rather than improvising an unprotected entry.

Last updated: September 2026

2.2 Confined-Space Entry, Fuel-Tank Safety & CDCCL Control

An aircraft fuel tank combines restricted access, difficult escape, residues and vapours, oxygen variation, conductive structure, and potential ignition sources. Entry is therefore managed as a confined-space task under the organisation's authorised procedure and the aircraft maintenance data. The controls are a system: removing fuel does not by itself make a tank safe, and a satisfactory atmosphere reading at one moment does not guarantee the next.

Planning and authorisation

The work package should identify the tank, access points, previous contents, isolation boundaries, ventilation method, required atmosphere tests, communications, lighting and tools, entrant and attendant roles, rescue arrangements, and stopping criteria. Fuel transfer, refuel or defuel, cross-feed, pumps, valves, electrical sources, hydraulic movement, and nearby work must be coordinated so another team cannot reintroduce a hazard.

The tank is drained and prepared by the approved method. Opening, purging, ventilation, and waste handling must control both vapour release and environmental exposure. Maintenance personnel do not invent a purging medium or use oxygen to improve the atmosphere. The specified ventilation equipment remains positioned so it does not introduce exhaust, static, or other ignition hazards.

Atmosphere testing

A suitable, in-date instrument is function-checked or bump-tested as required. Testing normally considers oxygen concentration, flammable vapour relative to the lower explosive limit, and any substance-specific toxic exposure identified by the risk assessment. Samples are taken at the locations and levels specified because vapour concentration may not be uniform.

Entry limits, alarm points, and retest frequency are established by the applicable confined-space procedure and local law. Published training values can help explain the concepts, but they are not a substitute for the authorised permit. Continuous or periodic monitoring is maintained as required. A ventilation failure, alarm, unexpected odour, illness, spill, or conflicting maintenance activity is a reason to leave the tank and reassess.

People, communication, and rescue

The entrant must be trained for the task and medically fit where the procedure requires it. Clothing and PPE are selected for fuel, solvent, skin, eye, respiratory, and mechanical exposure. Loose items are controlled, and movement routes are considered before entry.

A dedicated attendant remains outside, maintains the specified communication, tracks entrants, observes ventilation and instruments, prevents unauthorised entry, and initiates the rescue plan. The attendant does not make an impulsive, unprotected entry. Many confined-space fatalities involve would-be rescuers entering the same atmosphere without protection. Rescue equipment, competent responders, access clearance, and emergency communications must be workable before the first entrant goes inside.

Ignition-source control

Fuel-vapour ignition can result from electrical arcs, static discharge, unsuitable lamps or tools, hot surfaces, grinding, welding, or equipment operating near an opening. Only equipment authorised for the environment is used. Cables, lamps, ventilation units, and communication equipment are inspected and placed as the procedure directs. Aircraft bonding or earthing provisions are installed where specified; generic resistance values must not replace the approved limit and test method.

Hot work near a tank requires its own authorisation and aircraft-specific precautions. Even cold work can create heat or sparks if a tool slips, a fastener is drilled, or an electrical item fails. Work scope changes require reassessment.

CDCCLs and fuel-tank safety features

Critical Design Configuration Control Limitations identify design features necessary to prevent ignition. Examples may include wiring separation, routing, shielding, bonding, connector configuration, transient suppression, component qualification, or structural features. The controlling instructions state what must be preserved and how compliance is recorded.

A CDCCL is not a convenient recommendation. If maintenance discovers that a configuration cannot be restored exactly, work stops and approved engineering or design-authority instructions are obtained. Substituting wire, changing a route, omitting a clamp, altering a bond, or installing a different component can defeat an ignition-prevention assumption even when the system appears to operate normally.

Close-up and return to service

Before closing the tank, personnel and tools are accounted for, loose articles and cleaning materials are removed, work and independent inspections are completed, seals and access panels are installed to approved data, and all disturbed CDCCL features are verified. Ventilation and access controls are removed only in the planned order. Required leak checks, functional tests, records, and release actions are then completed.

The exam principle is straightforward: safe fuel-tank work depends on an authorised entry system, changing conditions are monitored, the rescue plan is ready before entry, ignition sources are controlled, and CDCCLs are restored exactly to approved design data.

Entry-Control Summary

  • Phase Evidence before continuing
  • Authorise Applicable entry permit, task data, isolations, entrant and attendant roles
  • Prepare Tank drained or prepared as directed, ventilation operating, rescue arrangement ready
  • Test Instruments checked and atmosphere within the procedure limits at required locations
  • Work Communication and monitoring maintained; ignition sources and scope changes controlled
  • Close People, tools and materials accounted for; CDCCLs, access and tests restored and recorded