Study guide
2.3 Emergency Response, Accident Remediation & Ballistic Recovery Systems
EASA Part-66 Module 07 — Maintenance Practices Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Safety Precautions — Electricity, Gases & Chemical Hazards
1.1 Electrical-System Hazards, Isolation & Protective Equipment 1.2 Compressed Gases, Pressure Vessels & Oxygen System Safety 1.3 Hazardous Chemicals, Solvents, Oils & Personal Protective Equipment
2 Chapter 2: Safety Precautions — Fire Protection, Confined Spaces & Emergency Response
2.1 Fire Classifications, Extinguishing Agents & Asphyxiation Risks 2.2 Confined-Space Entry, Fuel-Tank Safety & CDCCL Control 2.3 Emergency Response, Accident Remediation & Ballistic Recovery Systems
3 Chapter 3: Workshop Practices, Hand Tools & Precision Measurement
3.1 Workshop Housekeeping, Tool Control & Foreign Object Debris (FOD) 3.2 Engineering Dimensions, Allowances & Tolerances 3.3 Hand Tools, Powered Equipment & Operating Safety 3.4 Precision Measuring Instruments & Standards Traceability
4 Chapter 4: Fastener Torquing & Avionic Test Equipment
4.1 Torque Wrenches, Extension Calculations & Calibration Care 4.2 Multimeters, Megohmmeters & Insulation Testing 4.3 Bonding Testers, Milliohmmeters & Oscilloscopes
5 Chapter 5: Engineering Drawings, Standards & Fits
5.1 Orthographic Projections, Title Blocks & Revision Control 5.2 Drawing Line Conventions, Symbols & ATA Specification 100/iSpec 2200 5.3 Electrical Schematics, Wiring Interconnects & Component Location 5.4 Systems of Limits, Fits, Clearances & Shaft Alignment
6 Chapter 6: Electrical Wiring Interconnection System (EWIS)
6.1 EWIS Principles, Wire Types & Loom Routing Practices 6.2 Crimp Terminations, Connector Pin Insertion & Extraction Tooling 6.3 Electrical Bonding, Grounding Resistance & Electromagnetic Shielding
7 Chapter 7: Aircraft Riveting Practice
7.1 Solid and Blind Rivet Classifications, Materials & Head Markings 7.2 Rivet Spacing, Pitch, Edge Distance & Structural Layout 7.3 Countersinking, Dimpling Techniques & Rivet Installation 7.4 Rivet Joint Inspection, Failure Modes & Drill-Out Procedures
8 Chapter 8: Sheet Metal Working & Composite Materials
8.1 Sheet Metal Forming, Neutral Axis & Bend Allowance Calculations 8.2 Welding, Brazing, Soldering & Structural Adhesive Bonding 8.3 Composite Reinforcements, Pre-Preg Cold Storage & Clean Room Practice 8.4 Additive Manufacturing in Aircraft Maintenance
9 Chapter 9: Pipes, Flexible Hoses & Springs
9.1 Aircraft Rigid Tubing, Bending & 37-Degree Flaring Standards 9.2 Flexible Hoses, Installation Geometry & Serviceability 9.3 Aircraft Springs: Classifications, Rate Testing & Inspection
10 Chapter 10: Bearings & Mechanical Transmissions
10.1 Bearing Classifications, Load Types & Lubrication Practice 10.2 Bearing Defect Analysis: Spalling, Brinelling & Overheating 10.3 Gears, Gearboxes, Backlash Measurement & Belt/Chain Drives
11 Chapter 11: Flight Control Cables & Rigging
11.1 Aircraft Cable Construction, Sizing & Swaged Terminal Fittings 11.2 Cable Rigging, Turnbuckles & Temperature-Compensated Tensioning 11.3 Pulleys, Fairleads, Cable Inspection & Broken Strand Limits
12 Chapter 12: Aircraft Weight and Balance
12.1 Datum, Arm, Moment & Center of Gravity Principles 12.2 Aircraft Weighing Preparation, Equipment & Tare Deduction 12.3 Center of Gravity Calculations, Flight Limits & Ballast Adjustments
13 Chapter 13: Aircraft Handling, Storage & Winter Operations
13.1 Towing, Taxiing Protocols, Shear Pins & Wing Walkers 13.2 Jacking with Locking Collars, Chocking & Severe Weather Mooring 13.3 Ground De-icing and Anti-icing: Fluids, Clean Aircraft Concept & Holdover Times 13.4 Aircraft Parking, Protective Covers & Engine/Airframe Long-Term Preservation
14 Chapter 14: Inspection, Defect Assessment, Maintenance Procedures & Documentation
14.1 NDT Methods: Liquid Penetrant, Magnetic Particle, Eddy Current, Ultrasonic & Radiography 14.2 Corrosion Classifications, Mechanical Removal & Chemical Surface Treatments 14.3 Inspections After Lightning, Heavy Landing & Other Abnormal Events 14.4 Controlled Disassembly, Inspection & Reassembly 14.5 Troubleshooting, Defect Assessment & Repair Control 14.6 Maintenance Documentation, Work Reports & Shift Handover 14.7 Maintenance Planning, Stores Control, CRS & Occurrence Reporting
2.3 Emergency Response, Accident Remediation & Ballistic Recovery Systems
Key Takeaways Explain This Topic AI
Make an electrical-rescue scene safe before touching a casualty, summon help, and follow trained first-aid and AED procedures.
For chemical exposure, use the current SDS and site emergency process; do not improvise a neutralising treatment.
Battery spill response depends on battery chemistry and approved instructions.
Ballistic recovery systems are pyrotechnic devices whose safing method and exclusion zone are type-specific.
Last updated: September 2026
- 2.3 Emergency Response, Accident Remediation & Ballistic Recovery Systems
- Approved-Data Control
The figures and hardware examples in this section illustrate principles. For an actual aircraft or component, current approved maintenance data, product instructions, organisation procedures, and applicable law control the material, limit, interval, sequence, tooling, PPE, and acceptance decision.
Aviation maintenance environments subject engineers to high-voltage electrical circuits, aggressive chemical compounds, pressurized hydraulic lines, and pyrotechnic recovery devices. When accidents occur on the flight line or in the maintenance hangar, immediate, precise, and disciplined remediation protocols mean the difference between life and death. Furthermore, the proliferation of Whole Aircraft Rescue Parachute Systems (WARPS / BRS) in general aviation and composite aircraft introduces unique, explosive hazards that every modern certifying engineer must understand.
1. Electric Shock Remediation in the Aviation Workshop
Modern commercial and military aircraft utilize complex electrical architectures, including 115V AC 400Hz 3-phase power, 28V DC systems, and high-voltage DC systems (up to ±270V DC or 540V DC on advanced types like the Boeing 787). In workshops, industrial machine tools, variable frequency test benches, and Ground Power Units (GPUs) present severe electrical hazards.
Physiological Effects of Electric Current
It is a fundamental principle of electrical safety that current (amperage) kills, not voltage alone . While voltage provides the electromotive force to overcome human skin resistance, the physiological impact depends directly on the amperage crossing through the body:
1 mA to 5 mA: Sensation threshold; light tingling.
10 mA to 20 mA ("Let-Go" Threshold): Involuntary muscular contraction prevents the victim from releasing the energized conductor. Sustained contact causes rapid skin burn and drop in contact resistance.
50 mA to 100 mA: Ventricular fibrillation (rapid, uncoordinated fluttering of the heart muscle), resulting in cessation of blood circulation, irreversible brain damage within 4 minutes, and death if not immediately defibrillated.
>1,000 mA (1 A): Sustained cardiac standstill, massive internal and external burns, and respiratory center paralysis. +-----------------------------------------------------------------------+
- | ELECTRIC SHOCK EMERGENCY PROTOCOL |
- | |
- | STEP 1: ISOLATE POWER --> Hit Emergency Stop (EPO) or open breaker|
- | |
- | STEP 2: IF CANNOT BREAK --> Use non-conductive rescue hook to pull |
- | CIRCUIT casualty free (NEVER touch directly!) |
- | |
- | STEP 3: ASSESS & RESCUE --> Check breathing; if absent, start CPR |
- | LIFE SUPPORT (30:2) and deploy AED immediately. |
- | |
- | STEP 4: MEDICAL MONITOR --> Mandatory 24-hr hospital monitoring |
- | for delayed ventricular arrhythmia. |
- +-----------------------------------------------------------------------+
- Step-by-Step Electrical Rescue Procedure
Do NOT Touch the Casualty Directly: A rescuer who touches a victim still in contact with a live circuit will immediately become an electrical path to ground, suffering equal or fatal shock.
Immediate Circuit Isolation: Instantly disconnect the power source. Hit the nearest red Emergency Power Off (EPO) mushroom button, trip the master circuit breaker, pull the GPU quick-disconnect plug, or isolate the main disconnect switch.
Physical Separation Using Insulated Equipment: If the circuit cannot be switched off immediately, the rescuer must use an approved, rated non-conductive rescue hook (a high-voltage insulated fiberglass shepherd's crook, rated for at least 15 kV to 35 kV). Alternatively, use clean, dry, non-conductive materials such as a dry wooden pole, a heavy dry canvas strap, or dry natural fiber rope. Stand on a dry rubber insulating mat or dry wooden pallet while pulling the casualty free.
Assessment & Cardiopulmonary Resuscitation (CPR): Once the victim is free of the electrical hazard:
Check for responsiveness and normal breathing.
If the casualty is unresponsive and not breathing (or only gasping agonally), shout for immediate help, summon emergency medical services, and begin chest compressions immediately.
CPR Ratio: 30 high-quality chest compressions (at a rate of 100 to 120 compressions per minute and a depth of 5 to 6 cm) followed by 2 rescue breaths, or continuous hands-only chest compressions.
Automated External Defibrillator (AED): Retrieve and power on an AED immediately. Apply the defibrillator pads to the bare chest as indicated on the unit diagrams. Follow AED voice prompts; if ventricular fibrillation is detected, clear all personnel from the patient and deliver the shock.
Mandatory Hospital Medical Evaluation: Even if the casualty regains full consciousness and feels unimpaired, hospital evaluation is legally and medically mandatory. Electrical shock can trigger delayed fatal cardiac arrhythmias (ventricular fibrillation) up to 24 to 48 hours after the incident. Furthermore, high-voltage contact causes deep internal muscle and organ necrosis (rhabdomyolysis) that releases myoglobin into the bloodstream, resulting in delayed acute renal failure.
2. Chemical Contamination & Workshop Remediation
Aircraft maintenance involves aggressive chemical substances that cause acute chemical burns, severe ocular trauma, respiratory damage, and systemic toxicity upon contact.
Major Aviation Chemical Hazards
Phosphate Ester Hydraulic Fluids (Skydrol, HyJet): Extremely aggressive synthetic fluids. Contact with eyes causes intense, excruciating chemical burning and corneal epithelial erosion. Contact with skin causes severe dermatitis, erythema, and absorption toxicity.
Battery Electrolytes: Concentrated sulfuric acid ( H 2 S O 4 H_2SO_4 H 2 S O 4 , specific gravity 1.250–1.280) in lead-acid batteries; concentrated potassium hydroxide ( K O H KOH K O H , 30% by weight alkaline solution) in nickel-cadmium (Ni-Cd) batteries.
Solvents & Pre-Preg Resins: Methyl ethyl ketone (MEK), toluene, acetone, methylene chloride paint strippers, and un-cured epoxy/cyanate-ester composite resins.
Emergency Eye Wash Protocols
Under European Standard EN 15154 and international safety regulations, plumbed emergency eye wash stations must be located and maintained in accordance with the site risk assessment, applicable workplace rules, and the chemical SDS (battery shops, paint shops, hydraulic servicing bays). +-------------------------------------------------------------------------+
- | EMERGENCY EYE WASH 15-MINUTE RULE |
- | |
- | 1. Rush to eye wash station immediately (within 10 seconds). |
- | 2. Push the activation lever (hands-free continuous water flow). |
- | 3. Hold eyelids wide open using clean thumb and forefinger. |
- | 4. Flush eyes continuously for a MINIMUM OF 15 MINUTES. |
- | 5. Roll eyeballs up, down, and around to flush entire conjunctiva. |
- | 6. NEVER use neutralizing chemicals (acids/bases) in the eyes! |
- | 7. Transport to hospital with Chemical Safety Data Sheet (SDS). |
- +-------------------------------------------------------------------------+
The 15-Minute Rule: When chemical splash occurs, the victim must hold both eyelids wide open with clean fingers and flush the eyes continuously with clean, potable, tepid water for a MINIMUM of 15 minutes (extend to 20–30 minutes for alkaline splashes, which penetrate ocular tissue much deeper than acids).
The Absolute Ban on Chemical Neutralization in Eyes: Never attempt to chemically neutralize an acid or alkaline contamination in human eyes. Pouring a basic solution into an acid-contaminated eye (or vice versa) triggers an immediate exothermic chemical reaction . The resulting heat generation causes severe thermal burns on top of the chemical burn, causing permanent corneal scarring, cataract formation, and irreversible blindness. Only copious water or certified isotonic buffered saline flush is permitted.
Emergency Chemical Safety Showers
For large-scale bodily contamination (e.g., burst hydraulic hose or acid vat splash):
Immediately step under the shower and pull the overhead activation handle.
Strip Contaminated Clothing Under Water: The victim must vigorously strip off all contaminated overalls, underwear, footwear, and gloves while the shower is running . Removing clothing under flowing water prevents dragging saturated fabric across the face and reduces chemical dermal absorption.
Remain under the shower for at least 15 to 20 minutes .
Seek immediate medical evaluation; provide emergency doctors with the specific Chemical Safety Data Sheet (SDS).
Battery Electrolyte Neutralization Protocols
Battery maintenance shops represent a specialized high-hazard zone. Lead-acid batteries and nickel-cadmium batteries must be overhauled in strictly segregated, physically separated rooms with independent ventilation systems to prevent electrolyte cross-contamination (which causes explosive gas evolution and destroys battery plate chemistry).
Battery Type Electrolyte Compound Specific Hazards Mandatory Chemical Neutralizing Agent
Lead-Acid Sulfuric Acid ( H 2 S O 4 H_2SO_4 H 2 S O 4 ) Highly corrosive strong acid; attacks organic tissue, clothes, aluminum; generates explosive H 2 H_2 H 2 gas during charge Sodium Bicarbonate (Baking Soda, N a H C O 3 NaHCO_3 N a H C O 3 ) or dilute sodium carbonate solution. Apply until bubbling (effervescence of C O 2 CO_2 C O 2 ) ceases, then rinse with water.
Nickel-Cadmium (Ni-Cd) Potassium Hydroxide ( K O H KOH K O H ) Highly caustic strong alkaline (base); causes deep, liquefactive tissue necrosis; absorbs C O 2 CO_2 C O 2 to form potassium carbonate crystals 3% to 5% Boric Acid Solution ( H 3 B O 3 H_3BO_3 H 3 B O 3 ) or dilute acetic acid (vinegar). Apply thoroughly until neutralized, then rinse with water.
Ramp Chemical & Fuel Spill Containment
When a significant fuel (Jet A-1), hydraulic fluid, or oil spill occurs on the ramp or hangar floor:
Stop the Flow: Immediately shut off fuel dispensing nozzles, close shut-off valves, or disconnect servicing hoses.
Eliminate Ignition Sources: Instantly ban all vehicle movement, cell phones, ground power connections, and hot work within a 15-meter (50-foot) perimeter .
Deploy Spill Containment: Place absorbent booms and barriers around storm water drains, grease traps, and sewer inlets to prevent environmental contamination. Cover the fuel pool with inert absorbent granules (diatomaceous earth) or polypropylene absorbent pads.
Notify Authorities: For spills exceeding local threshold limits (typically >5 liters / 1 gallon of fuel), notify Airport Rescue and Firefighting (ARFF) and the airport environmental response unit immediately.
3. Ballistic Recovery Systems (BRS / WARPS) Safety
Whole Aircraft Rescue Parachute Systems (WARPS), commonly referred to as Ballistic Recovery Systems (BRS) or Cirrus Airframe Parachute System (CAPS) , are increasingly common across general aviation, high-performance singles, light sport aircraft (LSA), and very light jets (e.g., Cirrus SR20, SR22, Vision Jet SF50, Flight Design, Pipistrel, and various composite kitplanes). +-------------------------------------------------------------------------+
- | BALLISTIC RECOVERY SYSTEM (BRS/CAPS) ANATOMY |
- | |
- | [COCKPIT ACTIVATION HANDLE] --> Mechanical pull-handle (safety pin!) |
- | | |
- | (Shielded Cable) |
- | v |
- | [SOLID ROCKET MOTOR] --> Solid propellant pyrotechnic charge |
- | | (Extracts parachute in <1 second) |
- | v |
- | [PARACHUTE CANISTER] --> Deployable canopy packed in airframe |
- | | |
- | v |
- | [EGRESS HATCH / COVER] --> Breaks through composite fuselage |
- | HAZARD CONE: 30-50 FT (10-15 M) |
- +-------------------------------------------------------------------------+
- System Operation & Pyrotechnic Mechanics
The system consists of a large parachute canopy packed inside a structural canister, connected to the aircraft primary airframe structure via high-strength Kevlar or Vectran suspension bridles. The parachute is extracted by a solid-fuel rocket motor propelled by high-energy propellant (such as solid nitrocellulose or ammonium perchlorate composite). When the pilot pulls the cockpit activation handle, a mechanical firing pin or electronic squib strikes an ignition primer, firing the rocket motor.
The rocket ignites instantaneously, accelerating from 0 to over 160 km/h (100 mph) in milliseconds , blasting through an exterior composite breakout skin or blowing off a dedicated access hatch. It pulls the parachute canopy to full line stretch in less than one second, even under extreme aircraft attitude or spin conditions.
The Extreme Hangar Hazard: Inadvertent Ground Deployment
While BRS saves lives in flight, it represents an extreme, potentially fatal hazard to ground maintenance personnel :
Catastrophic Impact & Decapitation: Inadvertent ground firing inside a hangar will propel the rocket motor and metal canister into technicians, work stands, or the hangar roof at ballistic speeds. Personnel standing in the trajectory path will suffer fatal blunt-force trauma, amputation, or decapitation.
Hangar Blast & Shrapnel: If the rocket strikes a concrete ceiling or metal roof beam, it can deflect unpredictably, spraying burning solid rocket propellant, toxic exhaust gases, and shrapnel across the hangar floor.
Causes of Inadvertent Firing: Unintentional ground firing is typically caused by maintenance technicians snagging the mechanical activation handle while vacuuming or working inside the cockpit, moving seats, removing avionics panels, pulling flight control cables, or handling pyrotechnic rocket assemblies without grounding.
Mandatory Ground Safety Precautions
The Ground Mechanical Safety Pin:
Every BRS installation features a heavy-duty mechanical locking pin fitted with a high-visibility, bright red "REMOVE BEFORE FLIGHT" streamer.
THE FIRST ACTION PROTOCOL: Before any maintenance, inspection, cleaning, towing, or jacking commences on an aircraft equipped with a BRS, the maintenance technician must visually verify and confirm that the ground safety lock pin is fully inserted into the activation handle mechanism and mechanically locked.
The safety pin must remain installed at all times while the aircraft is in the hangar, on the ramp, or undergoing maintenance. It is only removed by the flight crew immediately prior to engine start.
Fuselage Trajectory Hazard Cone:
The exterior of the aircraft features prominent warning decals reading: "WARNING: ROCKET-DEPLOYED PARACHUTE SYSTEM — KEEP CLEAR" .
Personnel must maintain the deployment-path exclusion zone defined by the aircraft-specific ballistic-system maintenance data.
Never place hands, tools, or ladders over the rocket egress panel.
De-arming & Rocket Replacement Maintenance:
Rocket motors and parachute canopies have finite operating lives (typically 10 years for parachute repacking and rocket motor replacement).
Removal and installation of rocket canisters must be performed strictly in accordance with the Aircraft Maintenance Manual (AMM) and manufacturer service instructions.
Electrostatic Discharge (ESD) Protection: Technicians handling the rocket assembly must wear grounded anti-static wrist straps. An electrostatic spark jumping to an unshielded electronic ignition squib or primer can detonate the motor.
Immediately upon removal from the airframe, the rocket motor must be fitted with an approved metal transportation safety collar or sleeve, locked in an approved Class 1 explosive storage bunker, and transported under strict dangerous goods regulations.
- 4. Maintenance Scenarios & Exam Traps
- Realistic Scenario: Maintenance Inadvertence on a CAPS-Equipped Aircraft
An apprentice technician is assigned to remove the pilot's seat and center console in a Cirrus SR22 for a flight control cable inspection. While maneuvering a flashlight and ratchet under the console, the technician notices a red-handled T-cable assembly without a safety pin, with the activation cable under slight mechanical tension.
Correct Remediation: The technician must freeze all work immediately . Do not touch or disturb the cable or handle. Step carefully out of the cockpit without jostling the airframe. Immediately alert the licensed certifying engineer. The certifying engineer must retrieve the certified ground safety lock pin, insert it into the handle mechanism, verify the locking detent engages, and ensure the "REMOVE BEFORE FLIGHT" streamer is visible. Only after mechanical locking is verified may cockpit console work resume.
Common EASA Exam Traps
Trap 1: Chemical Eye Wash Duration. Exam questions often offer 5 or 10 minutes as flushing options. The mandatory international and European standard for chemical eye flushing is a minimum of 15 minutes (and up to 20–30 minutes for alkalis).
Trap 2: Neutralizing Eye Contaminants. A classic distractor suggests applying a weak acid (such as vinegar or boric acid) to neutralize an alkaline splash in the eye. Remember: chemical neutralization in the eye is strictly forbidden due to exothermic heat release that causes severe thermal damage. Only flush with clean water or isotonic saline.
Trap 3: Battery Electrolyte Neutralizers. Exam questions frequently invert the neutralizing agents: asserting that sodium bicarbonate is for Ni-Cd and boric acid is for lead-acid. Remember: Lead-acid (acid) is neutralized by sodium bicarbonate (base); Ni-Cd (alkali) is neutralized by boric acid (weak acid).
Trap 4: Rescuing Electric Shock Victims. Questions often ask what tool to use when pulling an energized casualty free. Options might include an aluminum ladder or a damp canvas strap. Only a certified non-conductive rescue hook (fiberglass) or completely dry, non-conductive wooden/insulating material is permitted.