Study guide
14.3 Inspections After Lightning, Heavy Landing & Other Abnormal Events
EASA Part-66 Module 07 — Maintenance Practices Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Safety Precautions — Electricity, Gases & Chemical Hazards
1.1 Electrical-System Hazards, Isolation & Protective Equipment 1.2 Compressed Gases, Pressure Vessels & Oxygen System Safety 1.3 Hazardous Chemicals, Solvents, Oils & Personal Protective Equipment
2 Chapter 2: Safety Precautions — Fire Protection, Confined Spaces & Emergency Response
2.1 Fire Classifications, Extinguishing Agents & Asphyxiation Risks 2.2 Confined-Space Entry, Fuel-Tank Safety & CDCCL Control 2.3 Emergency Response, Accident Remediation & Ballistic Recovery Systems
3 Chapter 3: Workshop Practices, Hand Tools & Precision Measurement
3.1 Workshop Housekeeping, Tool Control & Foreign Object Debris (FOD) 3.2 Engineering Dimensions, Allowances & Tolerances 3.3 Hand Tools, Powered Equipment & Operating Safety 3.4 Precision Measuring Instruments & Standards Traceability
4 Chapter 4: Fastener Torquing & Avionic Test Equipment
4.1 Torque Wrenches, Extension Calculations & Calibration Care 4.2 Multimeters, Megohmmeters & Insulation Testing 4.3 Bonding Testers, Milliohmmeters & Oscilloscopes
5 Chapter 5: Engineering Drawings, Standards & Fits
5.1 Orthographic Projections, Title Blocks & Revision Control 5.2 Drawing Line Conventions, Symbols & ATA Specification 100/iSpec 2200 5.3 Electrical Schematics, Wiring Interconnects & Component Location 5.4 Systems of Limits, Fits, Clearances & Shaft Alignment
6 Chapter 6: Electrical Wiring Interconnection System (EWIS)
6.1 EWIS Principles, Wire Types & Loom Routing Practices 6.2 Crimp Terminations, Connector Pin Insertion & Extraction Tooling 6.3 Electrical Bonding, Grounding Resistance & Electromagnetic Shielding
7 Chapter 7: Aircraft Riveting Practice
7.1 Solid and Blind Rivet Classifications, Materials & Head Markings 7.2 Rivet Spacing, Pitch, Edge Distance & Structural Layout 7.3 Countersinking, Dimpling Techniques & Rivet Installation 7.4 Rivet Joint Inspection, Failure Modes & Drill-Out Procedures
8 Chapter 8: Sheet Metal Working & Composite Materials
8.1 Sheet Metal Forming, Neutral Axis & Bend Allowance Calculations 8.2 Welding, Brazing, Soldering & Structural Adhesive Bonding 8.3 Composite Reinforcements, Pre-Preg Cold Storage & Clean Room Practice 8.4 Additive Manufacturing in Aircraft Maintenance
9 Chapter 9: Pipes, Flexible Hoses & Springs
9.1 Aircraft Rigid Tubing, Bending & 37-Degree Flaring Standards 9.2 Flexible Hoses, Installation Geometry & Serviceability 9.3 Aircraft Springs: Classifications, Rate Testing & Inspection
10 Chapter 10: Bearings & Mechanical Transmissions
10.1 Bearing Classifications, Load Types & Lubrication Practice 10.2 Bearing Defect Analysis: Spalling, Brinelling & Overheating 10.3 Gears, Gearboxes, Backlash Measurement & Belt/Chain Drives
11 Chapter 11: Flight Control Cables & Rigging
11.1 Aircraft Cable Construction, Sizing & Swaged Terminal Fittings 11.2 Cable Rigging, Turnbuckles & Temperature-Compensated Tensioning 11.3 Pulleys, Fairleads, Cable Inspection & Broken Strand Limits
12 Chapter 12: Aircraft Weight and Balance
12.1 Datum, Arm, Moment & Center of Gravity Principles 12.2 Aircraft Weighing Preparation, Equipment & Tare Deduction 12.3 Center of Gravity Calculations, Flight Limits & Ballast Adjustments
13 Chapter 13: Aircraft Handling, Storage & Winter Operations
13.1 Towing, Taxiing Protocols, Shear Pins & Wing Walkers 13.2 Jacking with Locking Collars, Chocking & Severe Weather Mooring 13.3 Ground De-icing and Anti-icing: Fluids, Clean Aircraft Concept & Holdover Times 13.4 Aircraft Parking, Protective Covers & Engine/Airframe Long-Term Preservation
14 Chapter 14: Inspection, Defect Assessment, Maintenance Procedures & Documentation
14.1 NDT Methods: Liquid Penetrant, Magnetic Particle, Eddy Current, Ultrasonic & Radiography 14.2 Corrosion Classifications, Mechanical Removal & Chemical Surface Treatments 14.3 Inspections After Lightning, Heavy Landing & Other Abnormal Events 14.4 Controlled Disassembly, Inspection & Reassembly 14.5 Troubleshooting, Defect Assessment & Repair Control 14.6 Maintenance Documentation, Work Reports & Shift Handover 14.7 Maintenance Planning, Stores Control, CRS & Occurrence Reporting
14.3 Inspections After Lightning, Heavy Landing & Other Abnormal Events
Key Takeaways Explain This Topic AI
An abnormal-event inspection is triggered, bounded, and escalated by current aircraft maintenance data and the event information available.
Before inspection, obtain crew reports, recorded exceedance data where available, aircraft configuration, mass, weather, and visible symptoms.
Lightning inspections follow possible attachment and exit paths and check structure, bonding, controls, antennas, composite zones, and affected systems as directed.
Heavy-landing or severe-turbulence inspections progress from the specified initial scope to deeper access, measurement, and NDT only when criteria require it.
A compass swing, rigging check, NDT method, or component removal is performed when the applicable procedure calls for it—not as an automatic universal action.
Last updated: September 2026
14.3 Inspections After Lightning, Heavy Landing & Other Abnormal Events
Abnormal-event inspections are conditional maintenance tasks. Their purpose is to determine whether loads, electrical energy, heat, contamination, or motion outside normal assumptions caused damage that is not captured by a routine inspection. The approved aircraft maintenance manual or other applicable instructions define the trigger, inspection zones, sequence, limits, and escalation.
Establish the event
Do not start with a memorised generic checklist. Obtain the crew report and technical-log entry, including indications, sounds, odours, aircraft configuration, phase of flight, weather, and handling effects. Use recorded load, exceedance, or maintenance-system data when the procedure permits. For a heavy landing, aircraft mass, vertical acceleration, attitude, sink rate, side load, and touchdown sequence may affect the required inspection. For overspeed, overtemperature, or overtorque, the magnitude and duration matter.
Make the aircraft safe before opening access. Isolate damaged systems, address fuel or hydraulic leakage, cordon off unstable areas, and preserve evidence. Record initial condition before cleaning or moving parts.
Lightning and high-energy electrical events
Lightning commonly attaches and exits at extremities, antennas, control surfaces, or other conductive paths, but the actual inspection follows aircraft-specific zones and evidence. Look for burns, pits, melted material, punctures, delamination, damaged sealant, loose fasteners, degraded bonding, and effects at hinges, bearings, static dischargers, radomes, lights, probes, and antennas. Composite structure may hide subsurface damage, so tap testing, ultrasonic inspection, or another approved method may be required.
Check affected electrical, fuel, flight-control, and avionic systems as the procedure directs. Bearings or hinges may be examined where current passage is possible. A magnetic-compass check or swing is performed only when required by the applicable maintenance data or when evidence indicates a magnetic effect; it is not automatically mandatory after every strike.
Heavy landing and severe turbulence
The initial inspection usually looks for evidence of load transfer: wrinkling, buckling, cracks, paint disturbance, pulled fasteners, leaks, misalignment, unusual gaps, landing-gear or wheel damage, and damage at attachments. The scope may include wings, fuselage, pressure bulkheads, engine or pylon attachments, control surfaces, doors, and landing gear.
If a limit is exceeded or initial evidence meets an escalation criterion, the approved task may require access removal, dimensional or symmetry checks, jacking, rigging checks, component removal, or NDT. Terms such as phase 1 and phase 2 are not universal across all types; follow the terminology and decision points for the aircraft being maintained.
Other conditional events
Bird strike, hail, tyre burst, brake overheat, runway excursion, ground collision, fluid contamination, propeller strike, engine exceedance, or flight into volcanic ash each has a different damage mechanism. For example, a tyre burst may damage nearby structure, wiring, hydraulic lines, and sensors; an overheat may affect material strength or seals beyond the visibly scorched area. The event-specific procedure identifies secondary zones.
Findings and release
Describe findings with location, orientation, dimensions, photographs, and references to inspection zones. Compare damage with approved limits; do not blend, drill-stop, straighten, degauss, or return a part to service without authorised instructions. When data are ambiguous or incomplete, Part-145 procedures require the issue to be reported through the maintenance organisation so clarification can be obtained.
Complete all required follow-on inspections, functional tests, independent inspections, records, and deferred-item controls. Release to service depends on the authorised person being satisfied that the ordered work is complete and that any known incompleteness is handled under the applicable rules.
The exam discipline is to link action to mechanism and data: establish what happened, make the aircraft safe, inspect the paths and load-transfer areas specified for that event, escalate only at defined criteria, and document the evidence.
Coordinating a conditional inspection
A useful work package divides the aircraft into stated zones and gives each finding a traceable reference. One team should not close a zone while another team is still assessing a connected load path or system. If evidence crosses zone boundaries—for example, a lightning exit mark near a control surface or fluid leakage following a landing event—the coordinator applies the escalation logic and expands the work only as the approved procedure directs.
Measurements need context. Record datum, instrument, units, access condition, temperature where relevant, and the exact limit used. A photograph without a location or scale cannot by itself support a disposition. Likewise, a downloaded flight-data value should be tied to the correct flight and interpreted through the authorised process.
Before release, reconcile the event report, inspection task, findings, engineering instructions, rectification, tests, and technical record. Confirm that temporary protections and isolations are removed in the correct order and that any recurring inspection or operational limitation is entered into the continuing-airworthiness system. If the event cannot be bounded or the prescribed data are unavailable, the aircraft remains controlled while the organisation obtains competent support; schedule pressure is not an inspection criterion.
Event-Evidence Map
- Event Evidence commonly considered under the approved task
- Lightning Attachment or exit marks, bonding paths, hinges, antennas, composite damage, affected systems
- Heavy landing Event data, gear and attachments, load-transfer structure, leaks, distortion and alignment
- Severe turbulence Recorded exceedance, wings and controls, fittings, cabin or interior attachment damage
- Overheat or overspeed Magnitude and duration, heat effects, clearances, seals, rotating parts and system tests
- Ground event Contact point, secondary load path, nearby lines or wiring, geometry and functional checks