Study guide

8.1 Sheet Metal Forming, Neutral Axis & Bend Allowance Calculations

EASA Part-66 Module 07 — Maintenance Practices Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Safety Precautions — Electricity, Gases & Chemical Hazards

1.1 Electrical-System Hazards, Isolation & Protective Equipment 1.2 Compressed Gases, Pressure Vessels & Oxygen System Safety 1.3 Hazardous Chemicals, Solvents, Oils & Personal Protective Equipment

2 Chapter 2: Safety Precautions — Fire Protection, Confined Spaces & Emergency Response

2.1 Fire Classifications, Extinguishing Agents & Asphyxiation Risks 2.2 Confined-Space Entry, Fuel-Tank Safety & CDCCL Control 2.3 Emergency Response, Accident Remediation & Ballistic Recovery Systems

3 Chapter 3: Workshop Practices, Hand Tools & Precision Measurement

3.1 Workshop Housekeeping, Tool Control & Foreign Object Debris (FOD) 3.2 Engineering Dimensions, Allowances & Tolerances 3.3 Hand Tools, Powered Equipment & Operating Safety 3.4 Precision Measuring Instruments & Standards Traceability

4 Chapter 4: Fastener Torquing & Avionic Test Equipment

4.1 Torque Wrenches, Extension Calculations & Calibration Care 4.2 Multimeters, Megohmmeters & Insulation Testing 4.3 Bonding Testers, Milliohmmeters & Oscilloscopes

5 Chapter 5: Engineering Drawings, Standards & Fits

5.1 Orthographic Projections, Title Blocks & Revision Control 5.2 Drawing Line Conventions, Symbols & ATA Specification 100/iSpec 2200 5.3 Electrical Schematics, Wiring Interconnects & Component Location 5.4 Systems of Limits, Fits, Clearances & Shaft Alignment

6 Chapter 6: Electrical Wiring Interconnection System (EWIS)

6.1 EWIS Principles, Wire Types & Loom Routing Practices 6.2 Crimp Terminations, Connector Pin Insertion & Extraction Tooling 6.3 Electrical Bonding, Grounding Resistance & Electromagnetic Shielding

7 Chapter 7: Aircraft Riveting Practice

7.1 Solid and Blind Rivet Classifications, Materials & Head Markings 7.2 Rivet Spacing, Pitch, Edge Distance & Structural Layout 7.3 Countersinking, Dimpling Techniques & Rivet Installation 7.4 Rivet Joint Inspection, Failure Modes & Drill-Out Procedures

8 Chapter 8: Sheet Metal Working & Composite Materials

8.1 Sheet Metal Forming, Neutral Axis & Bend Allowance Calculations 8.2 Welding, Brazing, Soldering & Structural Adhesive Bonding 8.3 Composite Reinforcements, Pre-Preg Cold Storage & Clean Room Practice 8.4 Additive Manufacturing in Aircraft Maintenance

9 Chapter 9: Pipes, Flexible Hoses & Springs

9.1 Aircraft Rigid Tubing, Bending & 37-Degree Flaring Standards 9.2 Flexible Hoses, Installation Geometry & Serviceability 9.3 Aircraft Springs: Classifications, Rate Testing & Inspection

10 Chapter 10: Bearings & Mechanical Transmissions

10.1 Bearing Classifications, Load Types & Lubrication Practice 10.2 Bearing Defect Analysis: Spalling, Brinelling & Overheating 10.3 Gears, Gearboxes, Backlash Measurement & Belt/Chain Drives

11 Chapter 11: Flight Control Cables & Rigging

11.1 Aircraft Cable Construction, Sizing & Swaged Terminal Fittings 11.2 Cable Rigging, Turnbuckles & Temperature-Compensated Tensioning 11.3 Pulleys, Fairleads, Cable Inspection & Broken Strand Limits

12 Chapter 12: Aircraft Weight and Balance

12.1 Datum, Arm, Moment & Center of Gravity Principles 12.2 Aircraft Weighing Preparation, Equipment & Tare Deduction 12.3 Center of Gravity Calculations, Flight Limits & Ballast Adjustments

13 Chapter 13: Aircraft Handling, Storage & Winter Operations

13.1 Towing, Taxiing Protocols, Shear Pins & Wing Walkers 13.2 Jacking with Locking Collars, Chocking & Severe Weather Mooring 13.3 Ground De-icing and Anti-icing: Fluids, Clean Aircraft Concept & Holdover Times 13.4 Aircraft Parking, Protective Covers & Engine/Airframe Long-Term Preservation

14 Chapter 14: Inspection, Defect Assessment, Maintenance Procedures & Documentation

14.1 NDT Methods: Liquid Penetrant, Magnetic Particle, Eddy Current, Ultrasonic & Radiography 14.2 Corrosion Classifications, Mechanical Removal & Chemical Surface Treatments 14.3 Inspections After Lightning, Heavy Landing & Other Abnormal Events 14.4 Controlled Disassembly, Inspection & Reassembly 14.5 Troubleshooting, Defect Assessment & Repair Control 14.6 Maintenance Documentation, Work Reports & Shift Handover 14.7 Maintenance Planning, Stores Control, CRS & Occurrence Reporting

8.1 Sheet Metal Forming, Neutral Axis & Bend Allowance Calculations

Key Takeaways Explain This Topic AI

Bend radius, grain direction, bend allowance, setback, relief, and tolerances come from the drawing or approved fabrication data.

The neutral-axis factor depends on material, temper, thickness, radius, and process; it is not one universal constant.

Use consistent units and the formula or bend table specified for the task.

Inspect bends for cracking, distortion, dimensions, finish damage, and conformance with the approved shape.

Last updated: September 2026

  • 8.1 Sheet Metal Forming, Neutral Axis & Bend Allowance Calculations
  • Approved-Data Control

Values and examples explain principles. Current approved maintenance data, product instructions, organisation procedures, and applicable law control actual limits, materials, intervals, methods, and acceptance.

In aircraft structural maintenance and manufacturing, fabricating replacement parts—such as formers, ribs, bulkheads, stringers, brackets, and skin doublers—requires precise bending of sheet metal. When flat metal is formed into an angle or channel, the material undergoes severe internal stresses and dimensional changes. Technicians must understand the physical mechanics of bending, the metallurgical constraints of aerospace alloys, and the exact mathematical formulas governing Setback and Bend Allowance to produce airworthy components that match engineering drawing tolerances.

Principles of Sheet Metal Bending & The Neutral Axis

When a flat strip of sheet metal is bent around a curved radius bar in a bending brake, the cross-section of the metal experiences two opposing forces:

Outer Fibre Tension: The material along the outside curve of the bend is stretched under severe tensile strain. The outer surface expands in area and thins slightly.

Inner Fibre Compression: The material along the inside curve of the bend is subjected to compressive stress. The inner surface contracts in area and thickens slightly. STRESS DISTRIBUTION ACROSS BEND

  • +-----------------------------------------+ <-- Outside Surface (Tension / Elongation)
  • | Tensile Stress (Fibre Stretching) |
  • | . . . . . . . . . . . . . . . . . . . . |
  • - - - - - - |=========================================| <-- NEUTRAL AXIS (Zero Stress / Constant Length)
  • 0.445 * T | Compressive Stress (Fibre Shrinkage) |
  • +-----------------------------------------+ <-- Inside Surface (Compression / Shrinkage)
  • <--- R ---> (Inside Bend Radius)
  • The Neutral Axis Concept

Between the tension zone on the outside and the compression zone on the inside lies a theoretical plane where the metal neither stretches nor shrinks. This plane is termed the neutral axis :

In a flat, unbent sheet subjected only to pure elastic deformation, the neutral axis lies exactly at the geometric centerline, or 0.50 T 0.50T 0.50 T ( 50 % 50\% 50% of the sheet thickness T T T ).

When sheet metal undergoes permanent plastic deformation during cold bending, the compressive forces on the inside face cause the material to yield more readily than under tension. This plastic flow shifts the neutral axis inward toward the inside surface of the bend .

For standard aerospace aluminium alloys bent to typical workshop radii (bend radii R < 3 T R < 3T R < 3 T ), aviation engineering empirical standards locate the neutral axis at approximately 0.445 T 0.445T 0.445 T from the inside bend surface.

Because the length of the neutral axis remains completely constant before, during, and after bending, all bend allowance calculations must be calculated along this 0.445 T 0.445T 0.445 T datum.

Minimum Bend Radius, Alloy Tempers & Grain Direction

Attempting to bend sheet metal around too sharp a corner generates extreme tensile stresses on the outer fibres that exceed the ultimate tensile strength of the material, resulting in surface micro-cracking, orange-peeling, or complete structural fracture.

Minimum Bend Radius ( R R R )

The minimum bend radius is defined as the smallest inside radius around which a specific sheet of metal can be formed without exhibiting cracking, structural weakening, or excessive thinning. It is expressed in terms of the inside bend radius ( R R R ) as a multiple of sheet thickness ( T T T ):

Alloy Composition & Temper: Annealed alloys (such as 2024-O or 7075-O ) possess high ductility and permit significantly sharper bend radii (often 1 T 1T 1 T to 2 T 2T 2 T ). In contrast, precipitation heat-treated alloys (such as 2024-T3 or 7075-T6 ) have high yield strengths and low remaining elongation, requiring larger minimum bend radii (often 2.5 T 2.5T 2.5 T to 5 T 5T 5 T ) to prevent fracture.

Sheet Thickness ( T T T ): Thicker sheets experience proportionally higher outer-fibre tensile strain for the same bend radius. Consequently, as sheet thickness increases, the required minimum bend radius ratio ( R / T R/T R / T ) increases.

Alloy & Temper 0.032 in (0.8 mm) 0.040 in (1.0 mm) 0.063 in (1.6 mm) 0.090 in (2.3 mm) Forming Characteristics

2024-O (Annealed) 1.0T – 1.5T 1.0T – 1.5T 1.5T – 2.0T 1.5T – 2.5T Highly ductile; easily formed cold; requires heat treatment post-forming

2024-T3 (Precipitation Treated) 2.0T – 2.5T 2.5T – 3.0T 3.0T – 4.0T 3.5T – 5.0T Standard structural skin alloy; prone to cracking if bent too sharply

6061-O (Annealed) 1.0T 1.0T 1.0T 1.0T – 1.5T Excellent formability; ideal for complex drawn or pressed parts

6061-T6 (Fully Aged) 1.5T – 2.0T 2.0T – 2.5T 2.5T – 3.0T 3.0T – 3.5T Moderate formability; good corrosion resistance without Alclad layer

7075-O (Annealed) 1.0T – 1.5T 1.5T – 2.0T 2.0T – 2.5T 2.0T – 3.0T High-strength zinc alloy; formable only in annealed condition

7075-T6 (Aged High Strength) 3.0T – 4.0T 3.5T – 4.5T 4.5T – 6.0T 5.5T – 7.0T Extreme notch sensitivity; cold bending should be avoided on critical parts

Grain Direction in Rolled Sheet

During the manufacturing of aluminium alloy sheet, large cast ingots are passed repeatedly through high-pressure rolling mills. This hot and cold rolling elongates the crystalline grains and non-metallic inclusions in the longitudinal direction of rolling, establishing a distinct grain direction (rolling grain):

Bending Across (Perpendicular to) Grain: When a bend is formed perpendicular to the rolling grain, the tensile stress is distributed across the long transverse axis of multiple grains. This maximizes crack resistance, allows tighter bend radii, and produces the strongest structural bend.

Bending Parallel to Grain: When a bend is formed parallel to the rolling grain, tensile stress acts directly along continuous grain boundaries and inclusion lines. The material tends to split, tear, or exhibit severe micro-fissuring along the outer bend radius. If parallel bends are unavoidable, the bend radius must be increased by at least one or two standard radius steps.

Layout Rule: When laying out parts containing intersecting bends (such as a four-sided tray or flanged rib), orient the blank so that all primary structural bends run at a 45 ∘ 45^\circ 4 5 ∘ angle to the sheet grain direction. This compromises between the two directions, ensuring neither bend is parallel to the grain.

Terminology & Layout Geometry: Mold Lines, Mold Points & Tangent Lines

To layout a flat sheet blank that will fold into the exact finished dimensions specified on an engineering drawing, technicians use standard geometric references: BEND GEOMETRY & REFERENCE LINES

  • Flange Leg 1 Mold Line 1
  • -----------------------+ BTL 1 |
  • \ |
  • \ v
  • \ Inside Radius (R) * Mold Point (MP)
  • \ /
  • ----------------------------+ BTL 2 /
  • Base Web Leg \ /
  • -----------------------------+ <-- Mold Line 2

Mold Line (ML): An extension of the flat, unbent exterior surfaces of the part past the bend to the point where they would intersect if the corner were sharp ( 0 0 0 radius).

Mold Point (MP): The vertex or point of intersection formed by the two intersecting mold lines. Exterior drawing dimensions on blueprints are almost universally given from mold point to mold point.

Bend Tangent Line (BTL): The precise line where the flat leg of the metal transitions into the curved arc of the bend radius. Every bend has two BTLs: the line where curvature begins, and the line where curvature ends.

Flat (or Leg): The straight, uncurved portion of the sheet between an edge and a BTL, or between two adjacent BTLs.

Setback (SB): The physical distance along the mold line from the Mold Point to the Bend Tangent Line ( S B = Mold Line Dimension − Flat Length SB = \text{Mold Line Dimension} - \text{Flat Length} SB = Mold Line Dimension − Flat Length ). It represents the amount that must be subtracted from the overall mold line dimension to find the flat leg length.

Bend Allowance (BA): The actual length of material consumed in the curved portion of the bend along the neutral axis. This is the curved distance between the two bend tangent lines.

Mathematical Formulations: Setback & Bend Allowance

Calculating the developed flat blank length requires determining the Setback ( S B SB SB ) for each flange and the Bend Allowance ( B A BA B A ) for each curved radius.

1. Setback Formula ( S B SB SB )

Setback is mathematically derived from right-angle trigonometry across the bend geometry: S B = K ( R + T ) SB = K(R + T) SB = K ( R + T )

Where:

  • R = R = R = Inside bend radius (inches or millimeters)
  • T = T = T = Metal thickness (inches or millimeters)

K = K = K = Setback factor, determined by the bend deflection angle θ \theta θ : K = tan ⁡ ( θ 2 ) K = \tan\left(\frac{\theta}{2}\right) K = tan ( 2 θ ​ )

Note on Bend Angles: In sheet metal terminology, the bend angle θ \theta θ is the deflection angle (the angle through which the metal has been bent from flat), NOT the included angle between the finished legs:

For a standard 90 ∘ 90^\circ 9 0 ∘ bend: θ = 90 ∘ ⟹ K = tan ⁡ ( 45 ∘ ) = 1.0 \theta = 90^\circ \implies K = \tan(45^\circ) = 1.0 θ = 9 0 ∘ ⟹ K = tan ( 4 5 ∘ ) = 1.0 . Therefore: S B 90 ∘ = R + T SB_{90^\circ} = R + T S B 9 0 ∘ ​ = R + T

For an open bend (deflection < 90 ∘ < 90^\circ < 9 0 ∘ , e.g., θ = 60 ∘ \theta = 60^\circ θ = 6 0 ∘ ): K = tan ⁡ ( 60 ∘ 2 ) = tan ⁡ ( 30 ∘ ) = 0.577 ⟹ S B = 0.577 ( R + T ) K = \tan\left(\frac{60^\circ}{2}\right) = \tan(30^\circ) = 0.577 \implies SB = 0.577(R + T) K = tan ( 2 6 0 ∘ ​ ) = tan ( 3 0 ∘ ) = 0.577 ⟹ SB = 0.577 ( R + T )

For a closed bend (deflection > 90 ∘ > 90^\circ > 9 0 ∘ , e.g., θ = 120 ∘ \theta = 120^\circ θ = 12 0 ∘ ): K = tan ⁡ ( 120 ∘ 2 ) = tan ⁡ ( 60 ∘ ) = 1.732 ⟹ S B = 1.732 ( R + T ) K = \tan\left(\frac{120^\circ}{2}\right) = \tan(60^\circ) = 1.732 \implies SB = 1.732(R + T) K = tan ( 2 12 0 ∘ ​ ) = tan ( 6 0 ∘ ) = 1.732 ⟹ SB = 1.732 ( R + T )

2. Bend Allowance Formula ( B A BA B A )

Bend Allowance represents the arc length along the neutral axis ( r n a = R + 0.445 T r_{na} = R + 0.445T r na ​ = R + 0.445 T ) through deflection angle θ \theta θ : B A = θ 360 ∘ × 2 π × ( R + 0.445 T ) BA = \frac{\theta}{360^\circ} \times 2\pi \times (R + 0.445T) B A = 36 0 ∘ θ ​ × 2 π × ( R + 0.445 T )

Converting radians and constants yields the universal aviation workshop formula: B A = ( 0.01743 R + 0.00778 T ) × θ BA = (0.01743 R + 0.00778 T) \times \theta B A = ( 0.01743 R + 0.00778 T ) × θ

Where R R R is inside bend radius, T T T is sheet thickness, and θ \theta θ is the bend deflection angle in degrees.

Step-by-Step Worked Calculation Example

Scenario: A technician must fabricate a U-channel stiffener from 2024-T3 aluminium . The engineering drawing specifies:

  • Sheet thickness: T = 0.040 in T = 0.040\text{ in} T = 0.040 in
  • Inside bend radius: R = 0.125 in R = 0.125\text{ in} R = 0.125 in ( 1 / 8 in 1/8\text{ in} 1/8 in )

Two 90 ∘ 90^\circ 9 0 ∘ bends ( θ 1 = 90 ∘ \theta_1 = 90^\circ θ 1 ​ = 9 0 ∘ , θ 2 = 90 ∘ \theta_2 = 90^\circ θ 2 ​ = 9 0 ∘ )

  • Left Flange overall mold line dimension: 1.250 in 1.250\text{ in} 1.250 in
  • Right Flange overall mold line dimension: 1.250 in 1.250\text{ in} 1.250 in
  • Base Web overall mold line dimension: 2.500 in 2.500\text{ in} 2.500 in
  • Step 1: Calculate Setback ( S B SB SB )

Because both bends are 90 ∘ 90^\circ 9 0 ∘ , K = 1.0 K = 1.0 K = 1.0 : S B = 1.0 × ( R + T ) = 0.125 + 0.040 = 0.165 in SB = 1.0 \times (R + T) = 0.125 + 0.040 = 0.165\text{ in} SB = 1.0 × ( R + T ) = 0.125 + 0.040 = 0.165 in

Step 2: Calculate Flat Lengths

Flange 1 Flat: Mold Line − S B = 1.250 − 0.165 = 1.085 in \text{Mold Line} - SB = 1.250 - 0.165 = 1.085\text{ in} Mold Line − SB = 1.250 − 0.165 = 1.085 in

Flange 2 Flat: Mold Line − S B = 1.250 − 0.165 = 1.085 in \text{Mold Line} - SB = 1.250 - 0.165 = 1.085\text{ in} Mold Line − SB = 1.250 − 0.165 = 1.085 in

Web Flat: The web sits between two mold points, so setback must be subtracted from both ends: Web Flat = Base Mold Line − ( 2 × S B ) = 2.500 − ( 2 × 0.165 ) = 2.500 − 0.330 = 2.170 in \text{Web Flat} = \text{Base Mold Line} - (2 \times SB) = 2.500 - (2 \times 0.165) = 2.500 - 0.330 = 2.170\text{ in} Web Flat = Base Mold Line − ( 2 × SB ) = 2.500 − ( 2 × 0.165 ) = 2.500 − 0.330 = 2.170 in

Step 3: Calculate Bend Allowance ( B A BA B A )

Using the standard formula for each 90 ∘ 90^\circ 9 0 ∘ bend: B A = ( 0.01743 × 0.125 + 0.00778 × 0.040 ) × 90 BA = (0.01743 \times 0.125 + 0.00778 \times 0.040) \times 90 B A = ( 0.01743 × 0.125 + 0.00778 × 0.040 ) × 90 B A = ( 0.002179 + 0.000311 ) × 90 = 0.002490 × 90 = 0.2241 in BA = (0.002179 + 0.000311) \times 90 = 0.002490 \times 90 = 0.2241\text{ in} B A = ( 0.002179 + 0.000311 ) × 90 = 0.002490 × 90 = 0.2241 in

Step 4: Calculate Total Developed Blank Length ( L t o t a l L_{total} L t o t a l ​ ) L t o t a l = Flange 1 Flat + B A 1 + Web Flat + B A 2 + Flange 2 Flat L_{total} = \text{Flange 1 Flat} + BA_1 + \text{Web Flat} + BA_2 + \text{Flange 2 Flat} L t o t a l ​ = Flange 1 Flat + B A 1 ​ + Web Flat + B A 2 ​ + Flange 2 Flat L t o t a l = 1.085 + 0.2241 + 2.170 + 0.2241 + 1.085 = 4.7882 in ≈ 4.788 in L_{total} = 1.085 + 0.2241 + 2.170 + 0.2241 + 1.085 = 4.7882\text{ in} \approx 4.788\text{ in} L t o t a l ​ = 1.085 + 0.2241 + 2.170 + 0.2241 + 1.085 = 4.7882 in ≈ 4.788 in

Sight Line (Brake Line) Calculation & Machine Setup

When clamping a sheet blank into a manual leaf brake (cornice brake) or box and pan brake, the technician cannot see the bend tangent line that sits underneath the clamping nose bar. To position the sheet precisely, a sight line (brake line) must be marked on the blank: SIGHT LINE POSITION IN BENDING BRAKE

  • Clamping Nose Bar (Radius = R)
  • +--------------+
  • | |
  • | |
  • +---------+ |
  • | |
  • ( R )|
  • +------------------------------------+--------------------------+ <-- Sheet Metal Blank
  • | | |
  • +------------------------------------+--------------------------+
  • ^ ^ ^
  • Edge BTL 1 Sight Line
  • (One Radius 'R'
  • ahead of BTL 1)

Sight Line Rule: The sight line is drawn exactly one inside bend radius ( R R R ) from the bend tangent line that is placed under the clamping nose bar, toward the portion of the sheet that will project outward.

Alignment: The technician clamps the sheet so that when sighting directly down the vertical front face of the brake nose bar, the sight line is perfectly aligned with the nose radius. When the bending leaf is rotated upward, the bend starts exactly at Bend Tangent Line 1 and finishes at Bend Tangent Line 2.

Relief Holes: Purpose, Sizing & Layout Geometry

When two flanges fold up at an angle to each other (such as the corners of a boxed rib or instrument chassis), the bend allowances of the two intersecting bends overlap. Without clearance, the metal at the corner would jam, buckle, and suffer violent compressive crushing and tearing.

Purpose of Relief Holes

Relief holes are drilled at the junction of intersecting bends to:

Eliminate compressive material jamming and deformation during bending.

Relieve severe stress concentrations at the corner.

Prevent fatigue cracks from initiating at the corner during operational flight loads.

Sizing Criteria

The hole diameter must be at least equal to the inside bend radius plus the sheet thickness: D h o l e ≥ R + T D_{hole} \ge R + T D h o l e ​ ≥ R + T .

Aviation structural repair manuals (such as FAA AC 43.13-1B and manufacturer SRMs) mandate an absolute minimum diameter of 1 / 8 in 1/8\text{ in} 1/8 in ( 3.2 mm 3.2\text{ mm} 3.2 mm ) , even if R + T R + T R + T is smaller.

Layout Procedure

Extend the inside Bend Tangent Lines (BTLs) of both intersecting bends until they cross.

The point of intersection of the two inside BTLs forms the exact center point for drilling the relief hole.

After drilling with a pilot drill and full-size reamer, the hole edges must be carefully deburred. Any scratch, chip, or burr left inside a relief hole serves as a primary stress riser, inducing fatigue failure under cyclic cabin pressurization or wing flexure.

  • Realistic Maintenance Scenario & Common Exam Traps
  • Realistic Maintenance Scenario

A licensed maintenance engineer is tasked with fabricating an internal rib stiffener from 0.050 in 0.050\text{ in} 0.050 in 2024-T3 sheet metal. The technician examines the sheet stock and identifies the rolled grain orientation indicated by the manufacturer's ink stamp lines. Because the part requires two perpendicular flanges, the engineer lays out the blank at a 45 ∘ 45^\circ 4 5 ∘ bias to the grain direction, ensuring neither bend is parallel to the rolling axis. Using an inside bend radius of 0.150 in 0.150\text{ in} 0.150 in ( 3 T 3T 3 T ), the technician calculates a setback of 0.200 in 0.200\text{ in} 0.200 in per bend, locates the inside BTLs, drills a 1 / 4 in 1/4\text{ in} 1/4 in relief hole at their intersection, deburrs the hole with a countersink tool, marks the sight line one radius ( 0.150 in 0.150\text{ in} 0.150 in ) outside BTL 1, and forms both flanges in a leaf brake without any micro-fissuring.

Common Exam Traps

Trap 1: Confusing the deflection angle with the included angle. In Setback and Bend Allowance formulas, θ \theta θ is the angle through which the metal deflects from flat. If a blueprint shows a finished flange angle of 60 ∘ 60^\circ 6 0 ∘ included between the legs, the metal was bent through 180 ∘ − 60 ∘ = 120 ∘ 180^\circ - 60^\circ = 120^\circ 18 0 ∘ − 6 0 ∘ = 12 0 ∘ of deflection. Using 60 ∘ 60^\circ 6 0 ∘ instead of 120 ∘ 120^\circ 12 0 ∘ yields erroneous setback and ruined material.

Trap 2: Locating the relief hole center at the Mold Point. A common error is centering the relief hole at the intersection of the mold lines. The mold point sits outside the physical boundary of the part. Relief holes must always be centered at the intersection of the inside bend tangent lines .

Trap 3: Misplacing the sight line. The sight line is located exactly one inside bend radius ( R R R ) from the bend tangent line, NOT one thickness ( T T T ) and NOT one setback ( S B SB SB ).