Study guide
8.2 Welding, Brazing, Soldering & Structural Adhesive Bonding
EASA Part-66 Module 07 — Maintenance Practices Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Safety Precautions — Electricity, Gases & Chemical Hazards
1.1 Electrical-System Hazards, Isolation & Protective Equipment 1.2 Compressed Gases, Pressure Vessels & Oxygen System Safety 1.3 Hazardous Chemicals, Solvents, Oils & Personal Protective Equipment
2 Chapter 2: Safety Precautions — Fire Protection, Confined Spaces & Emergency Response
2.1 Fire Classifications, Extinguishing Agents & Asphyxiation Risks 2.2 Confined-Space Entry, Fuel-Tank Safety & CDCCL Control 2.3 Emergency Response, Accident Remediation & Ballistic Recovery Systems
3 Chapter 3: Workshop Practices, Hand Tools & Precision Measurement
3.1 Workshop Housekeeping, Tool Control & Foreign Object Debris (FOD) 3.2 Engineering Dimensions, Allowances & Tolerances 3.3 Hand Tools, Powered Equipment & Operating Safety 3.4 Precision Measuring Instruments & Standards Traceability
4 Chapter 4: Fastener Torquing & Avionic Test Equipment
4.1 Torque Wrenches, Extension Calculations & Calibration Care 4.2 Multimeters, Megohmmeters & Insulation Testing 4.3 Bonding Testers, Milliohmmeters & Oscilloscopes
5 Chapter 5: Engineering Drawings, Standards & Fits
5.1 Orthographic Projections, Title Blocks & Revision Control 5.2 Drawing Line Conventions, Symbols & ATA Specification 100/iSpec 2200 5.3 Electrical Schematics, Wiring Interconnects & Component Location 5.4 Systems of Limits, Fits, Clearances & Shaft Alignment
6 Chapter 6: Electrical Wiring Interconnection System (EWIS)
6.1 EWIS Principles, Wire Types & Loom Routing Practices 6.2 Crimp Terminations, Connector Pin Insertion & Extraction Tooling 6.3 Electrical Bonding, Grounding Resistance & Electromagnetic Shielding
7 Chapter 7: Aircraft Riveting Practice
7.1 Solid and Blind Rivet Classifications, Materials & Head Markings 7.2 Rivet Spacing, Pitch, Edge Distance & Structural Layout 7.3 Countersinking, Dimpling Techniques & Rivet Installation 7.4 Rivet Joint Inspection, Failure Modes & Drill-Out Procedures
8 Chapter 8: Sheet Metal Working & Composite Materials
8.1 Sheet Metal Forming, Neutral Axis & Bend Allowance Calculations 8.2 Welding, Brazing, Soldering & Structural Adhesive Bonding 8.3 Composite Reinforcements, Pre-Preg Cold Storage & Clean Room Practice 8.4 Additive Manufacturing in Aircraft Maintenance
9 Chapter 9: Pipes, Flexible Hoses & Springs
9.1 Aircraft Rigid Tubing, Bending & 37-Degree Flaring Standards 9.2 Flexible Hoses, Installation Geometry & Serviceability 9.3 Aircraft Springs: Classifications, Rate Testing & Inspection
10 Chapter 10: Bearings & Mechanical Transmissions
10.1 Bearing Classifications, Load Types & Lubrication Practice 10.2 Bearing Defect Analysis: Spalling, Brinelling & Overheating 10.3 Gears, Gearboxes, Backlash Measurement & Belt/Chain Drives
11 Chapter 11: Flight Control Cables & Rigging
11.1 Aircraft Cable Construction, Sizing & Swaged Terminal Fittings 11.2 Cable Rigging, Turnbuckles & Temperature-Compensated Tensioning 11.3 Pulleys, Fairleads, Cable Inspection & Broken Strand Limits
12 Chapter 12: Aircraft Weight and Balance
12.1 Datum, Arm, Moment & Center of Gravity Principles 12.2 Aircraft Weighing Preparation, Equipment & Tare Deduction 12.3 Center of Gravity Calculations, Flight Limits & Ballast Adjustments
13 Chapter 13: Aircraft Handling, Storage & Winter Operations
13.1 Towing, Taxiing Protocols, Shear Pins & Wing Walkers 13.2 Jacking with Locking Collars, Chocking & Severe Weather Mooring 13.3 Ground De-icing and Anti-icing: Fluids, Clean Aircraft Concept & Holdover Times 13.4 Aircraft Parking, Protective Covers & Engine/Airframe Long-Term Preservation
14 Chapter 14: Inspection, Defect Assessment, Maintenance Procedures & Documentation
14.1 NDT Methods: Liquid Penetrant, Magnetic Particle, Eddy Current, Ultrasonic & Radiography 14.2 Corrosion Classifications, Mechanical Removal & Chemical Surface Treatments 14.3 Inspections After Lightning, Heavy Landing & Other Abnormal Events 14.4 Controlled Disassembly, Inspection & Reassembly 14.5 Troubleshooting, Defect Assessment & Repair Control 14.6 Maintenance Documentation, Work Reports & Shift Handover 14.7 Maintenance Planning, Stores Control, CRS & Occurrence Reporting
8.2 Welding, Brazing, Soldering & Structural Adhesive Bonding
Key Takeaways Explain This Topic AI
Oxy-acetylene welding of aircraft 4130 chrome-molybdenum steel requires a strict neutral flame (1:1 oxygen-to-acetylene ratio); carburizing flames introduce excess carbon causing brittleness, while oxidizing flames burn alloying elements and cause porosity.
Gas Tungsten Arc Welding (GTAW / TIG) utilizes a non-consumable tungsten electrode and inert gas; AC with high-frequency stabilization is mandated for aluminium to provide cathodic oxide cleaning, whereas DCEN (straight polarity) provides deep penetration for steel and titanium.
The Heat-Affected Zone (HAZ) adjacent to a weld experiences grain coarsening, recrystallization, and loss of heat treatment temper, requiring post-weld stress relief or normalizing to prevent fatigue failure.
Brazing joins metals via capillary action using non-ferrous filler metals melting above 450°C (840°F) into tight joint clearances (0.025 to 0.075 mm), whereas electrical soldering operates below 450°C using non-corrosive rosin flux.
Structural adhesive bonding depends entirely on chemical and mechanical surface preparation (phosphoric acid anodizing, chemical etching, and corrosion-inhibiting primer) and controlled autoclave or hot-bonder curing cycles.
Last updated: September 2026
- 8.2 Welding, Brazing, Soldering & Structural Adhesive Bonding
- Approved-Data Control
The figures and hardware examples in this section illustrate principles. For an actual aircraft or component, current approved maintenance data, product instructions, organisation procedures, and applicable law control the material, limit, interval, sequence, tooling, PPE, and acceptance decision.
Joining aircraft components demands exceptional mechanical strength, fatigue resistance, and environmental durability. Depending on the base alloy, component geometry, operating temperatures, and structural criticality, aviation maintenance engineers utilize fusion welding, non-fusion capillary joining (brazing and soldering), or structural adhesive bonding. Understanding the metallurgical transformations, chemical environments, operating parameters, and defect mechanisms of each joining technique is essential for ensuring continuing airworthiness.
Comparison of Joining Technologies
Thermal joining and adhesive bonding differ fundamentally in their operating temperatures, parent metal involvement, and load-transfer mechanisms:
Joining Process Temperature Range Parent Metal State Filler / Adhesive Material Primary Aircraft Applications
Fusion Welding (Oxy-acetylene, GTAW, GMAW) Above base metal melting point (>1,400°C for steel, >660°C for Al) Parent metal is fully melted and fused Matching composition filler rod or wire Engine tubular mounts (4130 steel), exhaust manifolds, turbine casings
Brazing (Torch, furnace, induction) Above 450°C (840°F), but below base metal melting point Parent metal is solid (not melted); joined via capillary action Non-ferrous alloy (silver-braze BAg, bronze BCuZn) Hydraulic tubing fittings, fuel line unions, heat exchangers
Soldering (Soft soldering) Below 450°C (840°F) (typically 183°C–215°C) Parent metal is solid ; joined via capillary wetting Tin-lead (Sn63/Pb37) or lead-free (SAC305) Electrical wire terminations, avionics circuit boards, ground lugs
Structural Adhesive Bonding 120°C to 175°C (250°F to 350°F) cure Parent metal/composite is solid ; joined via chemical adhesion Modified epoxy, phenolic, or polyimide film/paste Honeycomb sandwich panels, acoustic cowlings, skin-to-stiffener joints
Oxy-Acetylene Gas Welding & Flame Chemistry
Oxy-acetylene welding utilizes the combustion of pure oxygen and acetylene ( C 2 H 2 C_2H_2 C 2 H 2 ) to produce a concentrated flame reaching temperatures up to 3 , 150 ∘ C 3,150^\circ\text{C} 3 , 15 0 ∘ C ( 5 , 700 ∘ F 5,700^\circ\text{F} 5 , 70 0 ∘ F ) . Acetylene gas is dissolved in liquid acetone inside cylinders containing a porous monolithic mass (calcium silicate) because free acetylene becomes violently explosive if compressed above 15 psi 15\text{ psi} 15 psi ( 1 bar 1\text{ bar} 1 bar ) .
The Three Flame Classifications
The ratio of oxygen to acetylene supplied to the blowpipe torch dictates the chemical nature and temperature of the flame: OXY-ACETYLENE FLAME PROFILES
- 1. NEUTRAL FLAME (1:1 Ratio) - MANDATED FOR AIRCRAFT 4130 STEEL
- +-- Inner Cone (3,150°C) --------+-- Outer Envelope (Blue/Purple) ------->
- ( Sharp, rounded, luminous cone )
- 2. CARBURIZING / REDUCING FLAME (Excess Acetylene)
- +-- Inner Cone --+-- Acetylene Feather --+-- Outer Envelope ------------->
- ( Soft green feather indicates unburned carbon; causes steel embrittlement )
- 3. OXIDIZING FLAME (Excess Oxygen)
- +-- Pointed Cone --+-- Outer Envelope ----------------------------------->
- ( Short, sharp, hissing purple cone; burns alloying elements, creates slag )
Neutral Flame (1:1 Ratio): Equal volumes of oxygen and acetylene burn cleanly. The flame exhibits a well-defined, luminous, rounded inner cone without ragged edges, surrounded by a smooth bluish-purple envelope. Combustion is complete ( C 2 H 2 + O 2 → 2 C O + H 2 C_2H_2 + O_2 \rightarrow 2CO + H_2 C 2 H 2 + O 2 → 2 CO + H 2 in the inner cone, followed by oxidation to C O 2 CO_2 C O 2 and H 2 O H_2O H 2 O in the outer envelope). It neither adds carbon nor oxidizes the base metal. A neutral flame is strictly mandatory for welding aircraft 4130 chrome-molybdenum steel tubing.
Carburizing / Reducing Flame (Excess Acetylene): Contains more acetylene than oxygen, characterized by three distinct flame zones: the inner cone, a pale green "acetylene feather", and the outer envelope. The excess unburned carbon dissolves rapidly into the molten steel weld pool, forming hard, brittle iron carbides (cementite). This creates severe weld embrittlement, reduces tensile strength, and causes micro-cracking.
Oxidizing Flame (Excess Oxygen): Contains more oxygen than acetylene. The inner cone becomes short, sharply pointed, and emits a harsh, loud hissing sound. The excess oxygen reacts directly with the molten steel, burning out critical alloying elements (carbon, manganese, and silicon) and forming heavy iron oxide slag and porosity. The resulting weld is porous, weak, and extremely brittle. (Oxidizing flames are used only in specialized bronze welding of copper-zinc alloys).
Gas Tungsten Arc Welding (GTAW / TIG) & Polarity Selection
Gas Tungsten Arc Welding (GTAW) , commonly known as TIG (Tungsten Inert Gas) , is the premier electric arc welding process for aerospace structures. It produces an extremely clean, high-integrity weld pool using a non-consumable tungsten electrode shielded by an inert gas (pure argon, or helium-argon mixtures). No flux is required, eliminating corrosive slag entrapment.
Tungsten Electrodes
Aerospace GTAW electrodes are color-coded per ISO 6848 / AWS A5.12:
Pure Tungsten (Green): Low current capacity; used primarily on AC for older non-critical aluminium welding; forms a smooth balled tip.
2 % 2\% 2% Thoriated Tungsten (Red): Doped with thorium oxide ( T h O 2 ThO_2 T h O 2 ); exceptional arc stability, high electron emissivity, long tip life; ground to a sharp needle point for DC welding of steels and titanium (note: thorium is a low-level alpha emitter, requiring dust extraction during grinding).
Ceriated (Grey) & Lanthanated (Gold/Blue): Non-radioactive modern replacements offering superior arc starting and wide current performance across both AC and DC modes.
Current Modes & Polarity Mechanics
The electrical connection between the power source, torch electrode, and workpiece dictates heat distribution and cleaning action: GTAW CURRENT POLARITY MECHANISMS
- DCEN (Straight Polarity) DCEP (Reverse Polarity)
- Electrode Negative (-), Work Positive (+) Electrode Positive (+), Work Negative (-)
- [ Tungsten (-) ] [ Tungsten (+) ]
- | ^
- Electrons | (70% Heat to Work) Electrons | (70% Heat to Electrode)
- v |
- [ Workpiece (+) ] [ Workpiece (-) ]
- -------------------------- ---------------------------
- Deep, narrow penetration; Shallow penetration; extreme
- Excellent for Steel & Titanium electrode heating; Cathodic cleaning
Direct Current Electrode Negative (DCEN / Straight Polarity):
Mechanism: The tungsten electrode is connected to the negative terminal and the workpiece to the positive terminal. Fast-moving electrons bombard the workpiece, concentrating 70 % 70\% 70% of the total arc heat on the metal and only 30 % 30\% 30% on the tungsten electrode .
Results: Produces a deep, narrow weld bead with a narrow Heat-Affected Zone. The tungsten remains cool and maintains its sharp ground point.
Application: Mandated for 4130 chrome-molybdenum steel, stainless steel, nickel alloys (Inconel), and titanium .
Direct Current Electrode Positive (DCEP / Reverse Polarity):
Mechanism: Workpiece is negative; tungsten is positive. Electrons bombard the electrode, concentrating 70 % 70\% 70% of the heat on the tungsten , causing the electrode to melt and ball up rapidly even at low amperages.
Cathodic Cleaning Action: As electrons leave the workpiece, heavy positively charged shielding gas ions ( A r + Ar^+ A r + ) accelerate downward and slam into the metal surface. This physical bombardment pulverizes and strips away refractory surface oxides.
Application: Rarely used on DC due to severe electrode melting, but provides the physical basis for AC aluminium welding.
Alternating Current (AC) with High-Frequency (HF) Stabilization:
Mechanism: The current rapidly alternates between DCEN and DCEP (typically 60 to 200 cycles per second, stabilized by a superimposed high-frequency continuous spark to bridge zero-voltage crossings).
Dual Action on Aluminium: Aluminium is naturally coated with a tough, refractory aluminium oxide skin ( A l 2 O 3 Al_2O_3 A l 2 O 3 ) that melts at 2 , 050 ∘ C 2,050^\circ\text{C} 2 , 05 0 ∘ C ( 3 , 722 ∘ F 3,722^\circ\text{F} 3 , 72 2 ∘ F ) , whereas pure aluminium melts at only 660 ∘ C 660^\circ\text{C} 66 0 ∘ C ( 1 , 220 ∘ F 1,220^\circ\text{F} 1 , 22 0 ∘ F ) . Attempting to weld aluminium without removing this oxide causes the base metal to melt inside a wrinkled, un-fused oxide pouch.
During the DCEP half-cycle , cathodic ion bombardment shatters and blasts away the refractory A l 2 O 3 Al_2O_3 A l 2 O 3 skin (oxide cleaning).
During the DCEN half-cycle , heat penetrates deeply into the molten aluminium pool while cooling the tungsten.
Modern square-wave inverters allow technicians to independently adjust the balance control (e.g., 70 % 70\% 70% penetration DCEN vs 30 % 30\% 30% cleaning DCEP).
The Heat-Affected Zone (HAZ) & Post-Weld Stress Relief
The Heat-Affected Zone (HAZ) is the portion of solid parent metal immediately adjacent to the fusion line that was not melted, but whose microstructure, mechanical properties, and corrosion resistance were altered by the intense heat of welding.
Metallurgical Degradation in the HAZ
Grain Growth: Extreme temperatures cause solid-state recrystallization and rapid grain coarsening. Coarse grains possess lower impact toughness and are prone to brittle cleavage fracture.
Loss of Temper: In precipitation heat-treated alloys (such as 2024-T3 or 7075-T6 aluminium), the heat of welding dissolves strengthening precipitates and over-ages the surrounding matrix. Welding 2024 or 7075 destroys their temper, leaving the HAZ critically weak and susceptible to catastrophic intergranular stress-corrosion cracking . Consequently, fusion welding of 2024 and 7075 primary aircraft structures is strictly prohibited .
Residual Tensile Stresses: As the molten weld pool solidifies and cools, it contracts against the rigid, unmelted structure, leaving high residual tensile stresses locked in the joint.
Post-Weld Stress Relieving
On welded 4130 chrome-moly tubular fuselage frames and engine mounts, residual stresses must be relieved by heating the completed joint to 550 ∘ C − 650 ∘ C 550^\circ\text{C} - 650^\circ\text{C} 55 0 ∘ C − 65 0 ∘ C ( 1 , 020 ∘ F − 1 , 200 ∘ F 1,020^\circ\text{F} - 1,200^\circ\text{F} 1 , 02 0 ∘ F − 1 , 20 0 ∘ F ) using an oxy-acetylene torch with a neutral flame or induction heating coils, followed by slow, uniform cooling in still air or insulated wrapping. This relieves peak internal stresses and restores ductility.
Brazing & Soldering: Mechanisms & Standards
Non-fusion joining processes depend entirely on capillary action —the ability of a molten liquid to draw itself into narrow clearances between solid surfaces against external forces like gravity.
1. Brazing Operations
Definition: A thermal joining process where a non-ferrous filler metal has a melting point (liquidus) above 450 ∘ C 450^\circ\text{C} 45 0 ∘ C ( 840 ∘ F 840^\circ\text{F} 84 0 ∘ F ) , but below the melting point of the base metals being joined.
Silver Brazing (Silver Soldering): Uses silver-copper-zinc alloys (AWS BAg classifications) melting between 600 ∘ C 600^\circ\text{C} 60 0 ∘ C and 800 ∘ C 800^\circ\text{C} 80 0 ∘ C . Used extensively on aircraft hydraulic lines, pneumatic sensing lines, and pitot-static tubing.
Joint Clearance Criticality: Capillary attraction depends inversely on clearance. The optimal joint clearance for silver brazing is 0.001 in 0.001\text{ in} 0.001 in to 0.003 in 0.003\text{ in} 0.003 in ( 0.025 mm 0.025\text{ mm} 0.025 mm to 0.075 mm 0.075\text{ mm} 0.075 mm ) . If clearance is less than 0.001 in 0.001\text{ in} 0.001 in , flux becomes entrapped and the liquid alloy cannot penetrate; if clearance exceeds 0.005 in 0.005\text{ in} 0.005 in , capillary draw fails, joint voids form, and shear strength drops precipitously.
Brazing Fluxes: Chemical pastes containing fluorides and borates. Flux dissolves surface oxides, prevents air oxidation during heating, and reduces surface tension to allow complete wetting. Flux must be thoroughly washed off with hot water after brazing; residual flux is highly corrosive.
2. Soldering Standards in Aviation
Definition: Joining process using filler metals melting below 450 ∘ C 450^\circ\text{C} 45 0 ∘ C ( 840 ∘ F 840^\circ\text{F} 84 0 ∘ F ) .
Eutectic Solder (63/37): Aircraft electrical and avionic wiring is soldered using 63 % 63\% 63% tin / 37 % 37\% 37% lead (Sn63/Pb37) alloy. Unlike standard 60 / 40 60/40 60/40 solder (which transitions through a pasty, semi-solid phase between 183 ∘ C 183^\circ\text{C} 18 3 ∘ C and 190 ∘ C 190^\circ\text{C} 19 0 ∘ C ), the eutectic 63 / 37 63/37 63/37 alloy melts and solidifies at a single sharp temperature: 183 ∘ C 183^\circ\text{C} 18 3 ∘ C ( 361 ∘ F 361^\circ\text{F} 36 1 ∘ F ) . This eliminates "disturbed" or "cold" cracked solder joints caused by slight wire movement during cooling.
Flux Mandatory Rule: Only non-corrosive rosin-core fluxes (Type R, RMA per J-STD-004) are authorized on aircraft electrical connections. Acid, zinc chloride, or sal ammoniac fluxes are strictly prohibited on aircraft wiring because corrosive acid residues remain inside wire strands, causing rapid conductor green-rot corrosion and open-circuit failures.
Structural Adhesive Bonding: Surface Preparation & Curing
Structural adhesive bonding distributes flight loads uniformly across large surface areas, eliminating the stress concentration holes, fatigue notch sensitivity, and aerodynamic parasite drag associated with rivets and bolts.
Aerospace Adhesives
Film Adhesives: High-performance modified epoxies, phenolics, or bismaleimides supported on a lightweight woven nylon or polyester scrim cloth carrier. Supplied in frozen rolls ( < − 18 ∘ C <-18^\circ\text{C} < − 1 8 ∘ C ), cut to shape, and cured under heat ( 120 ∘ C − 175 ∘ C 120^\circ\text{C}-175^\circ\text{C} 12 0 ∘ C − 17 5 ∘ C ) and positive pressure ( 30 − 50 psi 30-50\text{ psi} 30 − 50 psi ) in an autoclave or heated vacuum press.
Paste Adhesives: Two-component liquid or thixotropic paste epoxies used for field repairs, edge closeouts, and honeycomb core potting. Room-temperature or elevated-temperature cure.
The Surface Preparation Hierarchy
Adhesive bonds rely on molecular adsorption and covalent chemical bonding. Over 90 % 90\% 90% of in-service adhesive bond failures originate from improper surface preparation rather than adhesive defect:
Solvent Degreasing: Removing oils and greases with approved solvents (MEK, acetone) using the "two-wipe" method (clean lint-free wipe saturated with solvent followed immediately by a clean dry wipe before solvent evaporates).
Chemical Etching: Alkaline cleaning followed by acid etching (such as Forest Products Laboratory / FPL sodium dichromate and sulfuric acid bath) to strip weak natural oxides.
Phosphoric Acid Anodizing (PAA, ASTM D3933): The aviation gold standard for aluminium bonding. Anodizing in phosphoric acid creates a micro-porous, stable oxide layer with microscopic protruding oxide "whiskers". When liquid adhesive is applied, it flows into these micro-pores and mechanically interlocks.
Corrosion-Inhibiting Adhesive Primer (CIAP): A thin ( 0.0001 in / 2.5 μ m 0.0001\text{ in} / 2.5\,\mu\text{m} 0.0001 in /2.5 μ m ) epoxy primer containing chromates applied within hours of anodizing. It protects the fragile oxide whiskers from moisture hydration and provides reactive chemical sites for adhesive cross-linking.
Water-Break Test: A simple shop floor verification of chemical cleanliness. Distilled water is poured over the prepared surface. If the water spreads into an unbroken, continuous film that holds for at least 30 seconds , the surface is chemically clean. If the water beads up, droplets form, or the film breaks, organic oil contamination is present, and the component must be re-cleaned.
Peel Ply in Composite Bonding
When manufacturing composite laminates intended for secondary adhesive bonding, a layer of peel ply (a tightly woven synthetic nylon or polyester fabric treated without release agents) is applied as the outermost ply during layup. After curing, the peel ply remains bonded to the laminate during storage and transit. Immediately prior to structural bonding, the technician peels the fabric off. This strips away surface contaminants and leaves a pristine, high-energy, textured surface ready for adhesive bonding without requiring manual mechanical sanding or abrasion .