Study guide
3.2 Engineering Dimensions, Allowances & Tolerances
EASA Part-66 Module 07 — Maintenance Practices Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Safety Precautions — Electricity, Gases & Chemical Hazards
1.1 Electrical-System Hazards, Isolation & Protective Equipment 1.2 Compressed Gases, Pressure Vessels & Oxygen System Safety 1.3 Hazardous Chemicals, Solvents, Oils & Personal Protective Equipment
2 Chapter 2: Safety Precautions — Fire Protection, Confined Spaces & Emergency Response
2.1 Fire Classifications, Extinguishing Agents & Asphyxiation Risks 2.2 Confined-Space Entry, Fuel-Tank Safety & CDCCL Control 2.3 Emergency Response, Accident Remediation & Ballistic Recovery Systems
3 Chapter 3: Workshop Practices, Hand Tools & Precision Measurement
3.1 Workshop Housekeeping, Tool Control & Foreign Object Debris (FOD) 3.2 Engineering Dimensions, Allowances & Tolerances 3.3 Hand Tools, Powered Equipment & Operating Safety 3.4 Precision Measuring Instruments & Standards Traceability
4 Chapter 4: Fastener Torquing & Avionic Test Equipment
4.1 Torque Wrenches, Extension Calculations & Calibration Care 4.2 Multimeters, Megohmmeters & Insulation Testing 4.3 Bonding Testers, Milliohmmeters & Oscilloscopes
5 Chapter 5: Engineering Drawings, Standards & Fits
5.1 Orthographic Projections, Title Blocks & Revision Control 5.2 Drawing Line Conventions, Symbols & ATA Specification 100/iSpec 2200 5.3 Electrical Schematics, Wiring Interconnects & Component Location 5.4 Systems of Limits, Fits, Clearances & Shaft Alignment
6 Chapter 6: Electrical Wiring Interconnection System (EWIS)
6.1 EWIS Principles, Wire Types & Loom Routing Practices 6.2 Crimp Terminations, Connector Pin Insertion & Extraction Tooling 6.3 Electrical Bonding, Grounding Resistance & Electromagnetic Shielding
7 Chapter 7: Aircraft Riveting Practice
7.1 Solid and Blind Rivet Classifications, Materials & Head Markings 7.2 Rivet Spacing, Pitch, Edge Distance & Structural Layout 7.3 Countersinking, Dimpling Techniques & Rivet Installation 7.4 Rivet Joint Inspection, Failure Modes & Drill-Out Procedures
8 Chapter 8: Sheet Metal Working & Composite Materials
8.1 Sheet Metal Forming, Neutral Axis & Bend Allowance Calculations 8.2 Welding, Brazing, Soldering & Structural Adhesive Bonding 8.3 Composite Reinforcements, Pre-Preg Cold Storage & Clean Room Practice 8.4 Additive Manufacturing in Aircraft Maintenance
9 Chapter 9: Pipes, Flexible Hoses & Springs
9.1 Aircraft Rigid Tubing, Bending & 37-Degree Flaring Standards 9.2 Flexible Hoses, Installation Geometry & Serviceability 9.3 Aircraft Springs: Classifications, Rate Testing & Inspection
10 Chapter 10: Bearings & Mechanical Transmissions
10.1 Bearing Classifications, Load Types & Lubrication Practice 10.2 Bearing Defect Analysis: Spalling, Brinelling & Overheating 10.3 Gears, Gearboxes, Backlash Measurement & Belt/Chain Drives
11 Chapter 11: Flight Control Cables & Rigging
11.1 Aircraft Cable Construction, Sizing & Swaged Terminal Fittings 11.2 Cable Rigging, Turnbuckles & Temperature-Compensated Tensioning 11.3 Pulleys, Fairleads, Cable Inspection & Broken Strand Limits
12 Chapter 12: Aircraft Weight and Balance
12.1 Datum, Arm, Moment & Center of Gravity Principles 12.2 Aircraft Weighing Preparation, Equipment & Tare Deduction 12.3 Center of Gravity Calculations, Flight Limits & Ballast Adjustments
13 Chapter 13: Aircraft Handling, Storage & Winter Operations
13.1 Towing, Taxiing Protocols, Shear Pins & Wing Walkers 13.2 Jacking with Locking Collars, Chocking & Severe Weather Mooring 13.3 Ground De-icing and Anti-icing: Fluids, Clean Aircraft Concept & Holdover Times 13.4 Aircraft Parking, Protective Covers & Engine/Airframe Long-Term Preservation
14 Chapter 14: Inspection, Defect Assessment, Maintenance Procedures & Documentation
14.1 NDT Methods: Liquid Penetrant, Magnetic Particle, Eddy Current, Ultrasonic & Radiography 14.2 Corrosion Classifications, Mechanical Removal & Chemical Surface Treatments 14.3 Inspections After Lightning, Heavy Landing & Other Abnormal Events 14.4 Controlled Disassembly, Inspection & Reassembly 14.5 Troubleshooting, Defect Assessment & Repair Control 14.6 Maintenance Documentation, Work Reports & Shift Handover 14.7 Maintenance Planning, Stores Control, CRS & Occurrence Reporting
3.2 Engineering Dimensions, Allowances & Tolerances
Key Takeaways Explain This Topic AI
Nominal dimension is the commercial designation, basic size is the exact theoretical size from which limits are calculated, and actual size is the measured physical dimension.
Allowance is the intentional difference between mating parts at Maximum Material Condition (MMC) that dictates clearance or interference.
Tolerances represent the total permissible variation on a single dimension: bilateral tolerances allow deviation in both directions from nominal, whereas unilateral tolerances permit deviation in only one direction.
Cumulative tolerance stack-up in chained assemblies can lead to severe mechanical binding or excessive slack; datum dimensioning eliminates cumulative tolerance buildup.
Last updated: September 2026
3.2 Engineering Dimensions, Allowances & Tolerances
Precision mechanical fit is foundational to aeronautical safety. Aircraft components operate under extreme dynamic loads, severe vibration, and cyclical thermal expansion ranging from -55°C at cruising altitude to over 200°C near engine cowlings. To ensure interchangeable parts assemble reliably without binding or structural flutter, maintenance engineers must master engineering drawing dimensions, limits of size, allowances, and tolerance calculations.
Fundamentals of Engineering Dimensions
Engineering drawings convey geometrical dimensions through precise metrological terms:
Nominal Dimension: The conventional size used for general identification, commercial designation, and cataloguing (e.g., a "25 mm bolt" or a "1/2-inch hydraulic line"). It is a name rather than an exact manufacturing target.
Basic Size: The exact theoretical dimension from which all permissible limits of size are derived through the application of allowances and tolerances. The basic size is identical for both mating components (the hole and the shaft) before tolerances are applied.
Actual Size: The physical dimension of a manufactured feature measured with a calibrated precision instrument under standardized environmental conditions (20°C / 68°F and 101.325 kPa per ISO 1). Basic Size = 25.000 mm
- |
- +-----┴------------------------+
- v v
- HOLE LIMITS SHAFT LIMITS
- Upper Limit: 25.021 mm Upper Limit: 24.980 mm
- Lower Limit: 25.000 mm Lower Limit: 24.967 mm
- Tolerance: 0.021 mm Tolerance: 0.013 mm
- |
- +--------------┬---------------+
- v
- ALLOWANCE (MMC)
- Smallest Hole - Largest Shaft
- 25.000 mm - 24.980 mm = +0.020 mm (Clearance Fit)
- The Principle of Allowance
Allowance is the intentional, prescribed difference between the dimensions of two mating parts at Maximum Material Condition (MMC) . Allowance represents the tightest permissible fit between mating components and dictates the functional nature of the joint:
Clearance Fit (Positive Allowance): The internal mating dimension (hole) at its minimum size is larger than the external mating dimension (shaft) at its maximum size. The parts assemble freely without mechanical force, ensuring a permanent running or sliding boundary for lubrication (e.g., flight control bellcrank pivot bearings, control cable pulley pins).
Interference Fit (Negative Allowance): The shaft at its maximum size is deliberately larger than the hole at its minimum size. Mating the components requires significant hydraulic press force, thermal expansion of the housing (heating in an oil bath or oven), or cryogenic contraction of the shaft (chilling in liquid nitrogen or dry ice). Once assembled, friction prevents relative movement (e.g., landing gear trunnion bushings, press-fit gear hub assemblies).
Transition Fit: The tolerance zones of the hole and shaft overlap. Depending on the actual manufactured sizes, the assembly may yield either a slight clearance or a slight interference. Used where precise location is required with light tapping or hand-press assembly (e.g., locating dowel pins, removable bearing retainers).
Tolerances: Bilateral vs. Unilateral
Tolerance is the total permissible variation of an individual dimension. Because no manufacturing process can produce identical parts to infinite precision, the designer specifies an acceptable band of variation:
Tolerance = Upper Limit of Size - Lower Limit of Size
Tolerance Type Characteristic Mathematical Example Upper Limit Lower Limit Total Tolerance
Bilateral Symmetrical Permissible variation is divided equally above and below the basic size 25.00 ± 0.05 mm 25.05 mm 24.95 mm 0.10 mm
Bilateral Asymmetrical Permissible variation extends in both directions from basic size, but by unequal amounts 25.00 +0.08 / -0.02 mm 25.08 mm 24.98 mm 0.10 mm
Unilateral (Positive) Variation is permitted in only one direction; the opposite deviation is zero 50.00 +0.05 / -0.00 mm 50.05 mm 50.00 mm 0.05 mm
Unilateral (Negative) Variation is permitted only below the basic size; upper deviation is zero 50.00 +0.00 / -0.04 mm 50.00 mm 49.96 mm 0.04 mm
Unilateral tolerances are standard for machined holes and reamed bores. When a reamer cuts a hole, tool wear causes subsequent holes to become smaller, but never smaller than the tool's ground diameter. Dimensioning a hole with a unilateral positive tolerance (+0.03 / -0.00 mm) ensures that tool wear never causes the hole to drop below the minimum functional boundary.
Limits of Size & Material Conditions
Every toleranced dimension defines two critical boundaries:
Upper Limit of Size (Maximum Limit): The largest permissible physical dimension of the feature.
Lower Limit of Size (Minimum Limit): The smallest permissible physical dimension of the feature.
Material Condition Terminology
Maximum Material Condition (MMC): The state of a component when it contains the maximum possible volume of material within its stated limits of size:
For an external feature (shaft, bolt, pin) , MMC occurs at the Upper Limit of Size (the largest permissible pin).
For an internal feature (hole, bore, bushing) , MMC occurs at the Lower Limit of Size (the smallest permissible hole).
Least Material Condition (LMC): The state of a component when it contains the minimum possible volume of material within its stated limits:
For an external feature , LMC occurs at the Lower Limit of Size (the smallest pin).
For an internal feature , LMC occurs at the Upper Limit of Size (the largest hole).
Practical Calculation Example
Consider an aircraft elevator hinge pin and its supporting bronze bushing:
- Bushing Internal Diameter (Hole): 20.00 +0.03 / -0.00 mm
- Upper Limit = 20.03 mm (LMC)
- Lower Limit = 20.00 mm (MMC)
- Hole Tolerance = 20.03 - 20.00 = 0.03 mm
- Hinge Pin Diameter (Shaft): 20.00 -0.02 / -0.05 mm
- Upper Limit = 19.98 mm (MMC)
- Lower Limit = 19.95 mm (LMC)
- Shaft Tolerance = 19.98 - 19.95 = 0.03 mm
Allowance (Tightest fit at MMC): Smallest Hole - Largest Shaft = 20.00 - 19.98 = +0.02 mm (Minimum Clearance = 0.02 mm).
Loosest fit (at LMC): Largest Hole - Smallest Shaft = 20.03 - 19.95 = +0.08 mm (Maximum Clearance = 0.08 mm).
Tolerance Stack-Up (Cumulative Tolerance Analysis)
Tolerance stack-up occurs when multiple components are assembled in a linear sequence, or when dimensions on a single component are dimensioned progressively in a chain. CHAIN DIMENSIONING (CUMULATIVE TOLERANCE STACK-UP):
- |<- A ->|<- B ->|<- C ->|
- [ 20.0 ± 0.1 ][ 30.0 ± 0.1 ][ 15.0 ± 0.1 ]
- |<---------------- TOTAL LENGTH ---------------->|
- 65.0 ± 0.3 mm (Worst-Case Error = ±0.3 mm)
DATUM / BASELINE DIMENSIONING (ZERO ACCUMULATION):
- |<------- A = 20.0 ± 0.1 ------->|
- |<-------------- B = 50.0 ± 0.1 ------------->|
- |<--------------------- C = 65.0 ± 0.1 ------>|
- | (DATUM)
- Worst-Case Arithmetic Stack-Up
In worst-case analysis, all maximum deviations are assumed to occur simultaneously in the same adverse direction:
- Total Maximum Tolerance = Σ(T_i)
- Assembly Calculation Example: Aircraft Flap Clevis Joint
An aircraft trailing edge flap clevis joint consists of a structural fork bracket containing a machined slot (W), two flanged bronze spacer washers (t1, t2), and a flap track drive lug (L):
- Bracket Slot Width (W): 50.00 ± 0.10 mm (Min = 49.90 mm, Max = 50.10 mm)
- Spacer Washer 1 (t1): 3.00 ± 0.03 mm (Min = 2.97 mm, Max = 3.03 mm)
- Spacer Washer 2 (t2): 3.00 ± 0.03 mm (Min = 2.97 mm, Max = 3.03 mm)
- Flap Track Drive Lug (L): 43.80 ± 0.05 mm (Min = 43.75 mm, Max = 43.85 mm)
The internal stack of components inside the bracket slot is S = t1 + t2 + L:
- Nominal Stack: 3.00 + 3.00 + 43.80 = 49.80 mm
- Maximum Stack (S_max): 3.03 + 3.03 + 43.85 = 49.91 mm
- Minimum Stack (S_min): 2.97 + 2.97 + 43.75 = 49.69 mm
Now, evaluate the clearance (C = W - S):
Minimum Operating Clearance (Tightest Fit): W_min - S_max = 49.90 - 49.91 = -0.01 mm ( Interference / Mechanical Binding! )
Maximum Operating Clearance (Loosest Fit): W_max - S_min = 50.10 - 49.69 = +0.41 mm ( Excessive Play / Aerodynamic Flutter! )
This calculation demonstrates why chain dimensioning is avoided in aerospace structures. A negative clearance (-0.01 mm) causes the flap joint to bind, preventing flap deployment, while +0.41 mm allows unacceptable aerodynamic vibration.
Statistical Tolerance Stack-Up (Root Sum of Squares - RSS)
Because the probability of all parts being simultaneously manufactured at their extreme dimensional limits is statistically remote, aerospace design often applies the Root Sum of Squares (RSS) method:
T_rss = √(Σ T_i²)
Applying RSS to the clevis stack: T_rss = √(0.03² + 0.03² + 0.05²) = √(0.0009 + 0.0009 + 0.0025) = √0.0043 ≈ 0.066 mm. The expected statistical variation is only ±0.066 mm, compared to the worst-case arithmetic accumulation of ±0.11 mm.
Standard Engineering Drawing Dimensioning Rules
Engineering drawings executed to ISO 128 / BS 8888 or ASME Y14.5 adhere to rigorous rules:
Datum Referencing: Critical functional dimensions must originate from a common, clearly identified physical datum surface (e.g., Datum A) rather than building upon adjacent features.
Avoid Redundancy: No feature should be dimensioned more than once. Over-dimensioning creates conflicting tolerances and ambiguity on the shop floor.
Projection and Leader Lines: Extension (projection) lines must not cross dimension lines unless unavoidable. A visible gap (approx. 1 to 2 mm) must be left between the feature outline and the start of the projection line.
Title Block General Tolerances: Dimensions shown without an explicit tolerance callout inherit the default tolerances stated in the drawing title block (e.g., Angles ±0.5°; Decimals X.X ±0.2 mm; X.XX ±0.05 mm).
Common Exam Traps & Pitfalls
Exam Trap 1: Confusing Allowance with Tolerance . Allowance is a design relationship between two mating parts at Maximum Material Condition (the tightest fit). Tolerance is the permissible variation on a single part's dimension.
Exam Trap 2: Calculating total bilateral tolerance as only the plus value. If a dimension is stated as 40.00 ± 0.04 mm, the total tolerance band is 0.08 mm (+0.04 - (-0.04)), not 0.04 mm.
Exam Trap 3: Neglecting temperature effects. Metal expands and contracts with temperature. Measuring an aluminium landing gear link (23 × 10⁻⁶ / K) at 35°C on a summer hangar floor will yield a significantly larger reading than its true dimension at the 20°C standard reference temperature.