Study guide

3.3 Hand Tools, Powered Equipment & Operating Safety

EASA Part-66 Module 07 — Maintenance Practices Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Safety Precautions — Electricity, Gases & Chemical Hazards

1.1 Electrical-System Hazards, Isolation & Protective Equipment 1.2 Compressed Gases, Pressure Vessels & Oxygen System Safety 1.3 Hazardous Chemicals, Solvents, Oils & Personal Protective Equipment

2 Chapter 2: Safety Precautions — Fire Protection, Confined Spaces & Emergency Response

2.1 Fire Classifications, Extinguishing Agents & Asphyxiation Risks 2.2 Confined-Space Entry, Fuel-Tank Safety & CDCCL Control 2.3 Emergency Response, Accident Remediation & Ballistic Recovery Systems

3 Chapter 3: Workshop Practices, Hand Tools & Precision Measurement

3.1 Workshop Housekeeping, Tool Control & Foreign Object Debris (FOD) 3.2 Engineering Dimensions, Allowances & Tolerances 3.3 Hand Tools, Powered Equipment & Operating Safety 3.4 Precision Measuring Instruments & Standards Traceability

4 Chapter 4: Fastener Torquing & Avionic Test Equipment

4.1 Torque Wrenches, Extension Calculations & Calibration Care 4.2 Multimeters, Megohmmeters & Insulation Testing 4.3 Bonding Testers, Milliohmmeters & Oscilloscopes

5 Chapter 5: Engineering Drawings, Standards & Fits

5.1 Orthographic Projections, Title Blocks & Revision Control 5.2 Drawing Line Conventions, Symbols & ATA Specification 100/iSpec 2200 5.3 Electrical Schematics, Wiring Interconnects & Component Location 5.4 Systems of Limits, Fits, Clearances & Shaft Alignment

6 Chapter 6: Electrical Wiring Interconnection System (EWIS)

6.1 EWIS Principles, Wire Types & Loom Routing Practices 6.2 Crimp Terminations, Connector Pin Insertion & Extraction Tooling 6.3 Electrical Bonding, Grounding Resistance & Electromagnetic Shielding

7 Chapter 7: Aircraft Riveting Practice

7.1 Solid and Blind Rivet Classifications, Materials & Head Markings 7.2 Rivet Spacing, Pitch, Edge Distance & Structural Layout 7.3 Countersinking, Dimpling Techniques & Rivet Installation 7.4 Rivet Joint Inspection, Failure Modes & Drill-Out Procedures

8 Chapter 8: Sheet Metal Working & Composite Materials

8.1 Sheet Metal Forming, Neutral Axis & Bend Allowance Calculations 8.2 Welding, Brazing, Soldering & Structural Adhesive Bonding 8.3 Composite Reinforcements, Pre-Preg Cold Storage & Clean Room Practice 8.4 Additive Manufacturing in Aircraft Maintenance

9 Chapter 9: Pipes, Flexible Hoses & Springs

9.1 Aircraft Rigid Tubing, Bending & 37-Degree Flaring Standards 9.2 Flexible Hoses, Installation Geometry & Serviceability 9.3 Aircraft Springs: Classifications, Rate Testing & Inspection

10 Chapter 10: Bearings & Mechanical Transmissions

10.1 Bearing Classifications, Load Types & Lubrication Practice 10.2 Bearing Defect Analysis: Spalling, Brinelling & Overheating 10.3 Gears, Gearboxes, Backlash Measurement & Belt/Chain Drives

11 Chapter 11: Flight Control Cables & Rigging

11.1 Aircraft Cable Construction, Sizing & Swaged Terminal Fittings 11.2 Cable Rigging, Turnbuckles & Temperature-Compensated Tensioning 11.3 Pulleys, Fairleads, Cable Inspection & Broken Strand Limits

12 Chapter 12: Aircraft Weight and Balance

12.1 Datum, Arm, Moment & Center of Gravity Principles 12.2 Aircraft Weighing Preparation, Equipment & Tare Deduction 12.3 Center of Gravity Calculations, Flight Limits & Ballast Adjustments

13 Chapter 13: Aircraft Handling, Storage & Winter Operations

13.1 Towing, Taxiing Protocols, Shear Pins & Wing Walkers 13.2 Jacking with Locking Collars, Chocking & Severe Weather Mooring 13.3 Ground De-icing and Anti-icing: Fluids, Clean Aircraft Concept & Holdover Times 13.4 Aircraft Parking, Protective Covers & Engine/Airframe Long-Term Preservation

14 Chapter 14: Inspection, Defect Assessment, Maintenance Procedures & Documentation

14.1 NDT Methods: Liquid Penetrant, Magnetic Particle, Eddy Current, Ultrasonic & Radiography 14.2 Corrosion Classifications, Mechanical Removal & Chemical Surface Treatments 14.3 Inspections After Lightning, Heavy Landing & Other Abnormal Events 14.4 Controlled Disassembly, Inspection & Reassembly 14.5 Troubleshooting, Defect Assessment & Repair Control 14.6 Maintenance Documentation, Work Reports & Shift Handover 14.7 Maintenance Planning, Stores Control, CRS & Occurrence Reporting

3.3 Hand Tools, Powered Equipment & Operating Safety

Key Takeaways Explain This Topic AI

Select the exact hand or powered tool and accessory specified for the fastener, material, speed, and task.

Secure the work, inspect guards and tooling, and control swarf, sparks, noise, dust, entanglement, and stored energy.

Cutting-tool direction and technique follow the tool manufacturer and maintenance procedure; forcing or reversing a tool can damage both tool and part.

Remove damaged or unsuitable tools from service and preserve tool accountability.

Last updated: September 2026

  • 3.3 Hand Tools, Powered Equipment & Operating Safety
  • Approved-Data Control

Values and examples explain principles. Current approved maintenance data, product instructions, organisation procedures, and applicable law control actual limits, materials, intervals, methods, and acceptance.

Aircraft maintenance demands specialized hand and pneumatic tools capable of operating within strict metallurgical tolerances. Using an incorrect screwdriver tip, an improper hacksaw blade pitch, or an undressed chisel can ruin expensive airframe components or inflict severe personal injury. EASA Part-66 Module 7 requires an in-depth understanding of tool geometry, material compatibility, and operational safety.

Striking Tools: Hammers & Mallets

Striking tools are categorized by head material and functional application:

Ball-Peen Hammer: The standard workshop striking tool. Features a flat striking face for driving cold chisels and pin punches, and a hemispherical "peen" on the reverse side. The ball peen is used for expanding rivet shanks, peening metal plates, and forming radiused internal corners. Heads are forged high-carbon steel, heat-treated so the striking face is hard while the eye remains softer to absorb impact without fracturing. Sized by head weight, ranging from 2 oz (light sheet metal work) to 2 lb (heavy structural maintenance).

Soft-Faced Mallets: Essential when striking finished aircraft alloys, bearing housings, ground shafts, or cadmium-plated hardware. Heads are manufactured from brass, copper, lead, rawhide, rubber, or high-density polyurethane/nylon. They deform slightly upon impact, distributing force over a larger contact area and preventing surface gouging, work hardening, or micro-cracking of structural aluminium.

Dead-Blow Hammers: Feature a hollow composite or polyurethane head partially filled with steel shot or lead pellets. When swung, the shot lags behind during the initial stroke. Upon impact, the shot shifts forward in a continuous flow, dampening rebound shock, eliminating bounce-back, and transferring 100% of kinetic energy into the workpiece. Crucial for seating precision bearings and assembling close-tolerance interference joints without damaging internal raceways.

Screwdrivers & Aerospace Drive Systems

Aerospace fasteners experience high torque loads and require dedicated drive profiles to prevent cam-out (the tendency of the driver tip to slip upward out of the fastener recess under rotational torque):

Drive System Visual Profile Mechanical Characteristics Typical Aircraft Applications Interchangeability Rules

Slotted Single straight slot Prone to side-slippage; screwdriver blade must fill 75% to 100% of slot width Non-structural brackets, clamp screws Use flat cabinet tips with parallel sides; never use tapered tips

Phillips Symmetrical cruciform with rounded internal corners Designed to cam out at high torque to prevent overtightening in production lines Cabin interior fittings, electrical terminal covers Never use in Posidriv or Torq-Set recesses; will cause immediate cam-out

Posidriv Cruciform with parallel-sided ribs and 45° secondary radial tick marks Ribs do not taper; virtually eliminates cam-out; allows significantly higher tightening torque General airframe systems, European aircraft structures Do not interchange with Phillips; Phillips bits slip and strip Posidriv recesses

Torq-Set Cruciform where the four wings are offset from the central axis Asymmetrical offset wings deliver exceptionally high torque transfer without cam-out High-shear structural skins, wing access panels, fuel tank panels Requires dedicated Torq-Set bits; standard cross-head bits will destroy the fastener

Tri-Wing Three radial slots meeting at a common center point Tamper-resistant profile with excellent torque transmission Security panels, flight data recorder enclosures, avionics bays Driven exclusively with matched Tri-Wing drivers

Torx (Star) Six-lobed internal star profile 15° drive angle delivers true radial torque with zero cam-out and minimal operator thrust load Modern structural airframes, engine accessory mounts, hydraulic pumps Ensure correct Torx size (T10, T15, T20, etc.); undersized bits round off lobes PHILLIPS POSIDRIV TORQ-SET TRI-WING

  • (Symmetrical) (45° Ticks & Ribs) (Offset Cruciform) (3-Flute Radial)
  • | | | |
  • ───┼─── ───┼─── ───┼─── ───┼───
  • | | ─┼─ |
  • (Tapered corners) (Parallel flutes) (Wings offset) (Tamper-resistant)
  • Cold Chisels: Types, Cutting Angles & Safety

Cold chisels are forged from high-carbon or chrome-vanadium tool steel, hardened and tempered at the cutting edge, with a softer, tougher striking head.

Chisel Classifications

Flat Cold Chisel: The most common workshop chisel. Used for chipping flat surfaces, shearing sheet metal along vice jaws, and splitting seized nuts.

Cross-Cut (Cape) Chisel: Features a narrow cutting edge with a body that tapers backward to provide clearance. Used for cutting keyways, rectangular slots, and narrow grooves.

Diamond-Point Chisel: Tapered to a square section ground diagonally to produce a sharp diamond-shaped cutting point. Used for cutting V-grooves and cleaning out sharp internal 90° corners.

Round-Nose Chisel: Features a semi-circular cutting edge. Used for cutting concave oil grooves in bronze sleeve bearings and drawing off-centre drill holes back on track. +-------------------------------------------------------------+

  • | COLD CHISEL CUTTING EDGE GEOMETRY |
  • +-------------------------------------------------------------+
  • | Included Angle: 60° to 70° (for aircraft steels & aluminium)|
  • | Soft Metals: 30° to 40° (copper, brass, soft materials) |
  • | Cutting Edge: Slightly convex curvature to prevent |
  • | sharp outer corners from digging in |
  • +-------------------------------------------------------------+
  • Cutting Angles & Edge Geometry

The cutting edge is ground to an included angle of 60° to 70° for general aircraft steels and aluminium alloys. For softer metals (copper, lead, soft brass), the angle may be reduced to 30° to 40°. The cutting edge should be ground with a slight convex curve ; this ensures the centre of the edge enters the metal first, preventing the sharp fragile corners from digging in and snapping off.

Striking Head Dressing & Safety

Repeated striking by steel hammers causes the soft steel at the chisel's struck end to mushroom and crack. Mushroomed heads present an extreme safety hazard: subsequent hammer blows will fracture the curled metal burrs, launching razor-sharp steel fragments across the workshop at lethal velocity.

Technicians must dress striking heads regularly on a bench grinder, restoring a clean 45° chamfer around the perimeter. Always wear ballistic safety goggles when striking or grinding chisels.

Hacksaws: Frame Types, Blades & TPI Selection

A hacksaw consists of an adjustable or rigid steel frame and a replaceable flexible high-speed steel (HSS) or bi-metal blade. Blades are installed with teeth pointing forward, away from the handle , cutting exclusively on the forward push stroke.

The Fundamental Rule of Pitch Selection

Blade pitch is designated by Teeth Per Inch (TPI) . The golden rule of hacksawing mandates that at least 2 to 3 teeth must be in continuous engagement with the workpiece cross-section at all times .

If the material thickness is less than the pitch between two adjacent teeth, the edge will fall into the tooth gullet, causing the tooth to straddle the metal, snag violently, and strip off the blade.

  • Blade Pitch Recommended Material Thickness Optimal Aerospace Applications
  • 14 TPI Over 25 mm (1 inch) Thick solid stock, large aluminium billets, brass bar, soft mild steel
  • 18 TPI 12 to 25 mm (1/2 to 1 inch) General structural steel bar, heavy brackets, tool steel
  • 24 TPI 6 to 12 mm (1/4 to 1/2 inch) Medium-wall structural tubing, angle extrusions, channel sections
  • 32 TPI Under 6 mm (down to 1 mm) Thin-walled hydraulic tubing, fuel lines, sheet metal skins
  • Sawing Technique

Operate the hacksaw at a controlled rhythm of 40 to 50 strokes per minute . Apply downward pressure strictly during the forward stroke. Relieve all cutting pressure on the return stroke; dragging teeth backward under pressure breaks off fine tooth points and dulls the cutting edge prematurely.

Engineering Files: Classifications, Care & Safety

Files are classified by their cut (tooth pattern), length, and degree of coarseness:

Single-Cut: A single series of parallel, unbroken diagonal teeth cut across the face at an angle of 65° to 85° to the centerline. Operates with light pressure to produce a smooth, polished surface. Ideal for draw-filing and deburring thin sheet metal.

Double-Cut: Two intersecting series of diagonal teeth. The first cut (overcut, 40° to 45°) is overlaid with a second, deeper cut (upcut, 70° to 80°), creating thousands of diamond-shaped cutting points. Designed for rapid metal removal.

Coarseness Hierarchy

Files are graded from coarsest to finest: Rough → Bastard → Second-Cut → Smooth → Dead-Smooth . The spacing of teeth depends on both the grade and the file length (a 12-inch bastard file has coarser teeth than an 8-inch bastard file). [Coarse / Rapid Stock Removal] [Precision Finishing]

  • Rough ──► Bastard ──► Second-Cut ──► Smooth ──► Dead-Smooth
  • File Chalking & Pinning Prevention

Soft metals (aluminium, bronze, copper) tend to clog the file teeth, a condition known as pinning . The trapped metal pins score and gouge the workpiece surface. To prevent pinning:

Clean teeth regularly using a file card (a stiff wire brush mounted on leather) pulled parallel to the tooth flutes.

Apply blackboard chalk rubbed thoroughly across the file face before cutting soft alloys. Chalk acts as a dry lubricant, preventing soft swarf from adhering to the tooth gullets.

Mandatory Workshop Safety Rule

NEVER use a file without a securely fitted, undamaged handle. The pointed, tapered tang is hard and sharp. If a file snags on the forward stroke without a handle, the tang will be driven directly into the technician's palm or wrist, puncturing arteries or nerve bundles.

Twist Drills, Powered Equipment & Precision Reamers

Precision hole preparation in airframe structures requires specific drill geometry and careful speed regulation: +------------------------------------+------------------------------------+

  • | 118° STANDARD POINT | 135° SPLIT POINT |
  • +------------------------------------+------------------------------------+
  • | - Point angle: 118° | - Point angle: 135° |
  • | - Lip clearance: 8° to 12° | - Lip clearance: 8° to 12° |
  • | - Standard chisel edge | - Split chisel (self-centering) |
  • | - For: General steels & aluminium | - For: Titanium, stainless alloys |
  • +------------------------------------+------------------------------------+
  • Twist Drill Point Angles

118° Standard Point: The universal point angle for general mild steel, alloy steels, and aluminium alloys. Lip clearance angle is ground to 8° to 12°.

135° Split Point: Designed for hard, work-hardening alloys (titanium, stainless steel, Inconel). The flatter angle creates a shorter cutting lip, while the split chisel edge eliminates the blunt chisel center, allowing the drill to self-center without "wandering" and reducing required feed thrust by 40%.

90° Point: Used for drilling plastics, Plexiglas/acrylic cabin windows, and composite laminates. Prevents grabbing and breakout cracking on the exit side of the hole.

Microstop Countersink Cages

When preparing holes for flush solid rivets (such as 100° countersunk rivets), hand drilling can easily produce oval or overly deep countersinks that weaken the skin. Technicians use a microstop countersink cage . The tool features a spring-loaded nylon foot that contacts the skin without scratching, and a micrometer-threaded barrel adjustable in 0.001-inch (0.025 mm) increments to ensure perfectly repeatable countersink depth.

Precision Reamers & The Golden Rule

Drilling produces a hole that is slightly out-of-round and rough. Precision aircraft holes for close-tolerance bolts (e.g., NAS or MS bolts) are finished using a precision reamer (hand reamer with a tapered lead or spiral-flute machine reamer). Reaming removes the final 0.10 to 0.25 mm of metal, producing a mirror-smooth surface with dimensional accuracy to within 0.01 mm.

The Golden Rule of Reaming: A reamer must ALWAYS be turned in the clockwise (cutting) direction , both when feeding into the hole and when withdrawing it. Reversing the rotation wedges microscopic metal chips behind the relief faces of the cutting flutes, instantly dulling the cutting edges and scoring deep spiral scratches into the finished bore.