Study guide

4.3 Stall Physics, Critical Angle of Attack & High-Lift Devices

EASA Part-66 Module 08 - Basic Aerodynamics Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Physics of the Atmosphere

1.1 International Standard Atmosphere (ISA) Datum & Atmospheric Layers 1.2 Atmospheric Pressure, Temperature, and Air Density Variations 1.3 Humidity, Dew Point, and Density Altitude Effects on Aircraft Performance

2 Chapter 2: Aerodynamics & Airflow Characteristics

2.1 Airflow Around Bodies & The Boundary Layer 2.2 Flow Phenomena: Upwash, Downwash, Wingtip Vortices & Stagnation Point 2.3 Aerofoil Geometry & Design Parameters

3 Chapter 3: Lift, Drag & Aerodynamic Forces

3.1 Bernoulli's Principle, Venturi Effect & Lift Generation 3.2 The Lift Equation & Lift Coefficient 3.3 Drag Components: Parasite, Profile & Induced Drag 3.4 The Total Drag Polar Curve & Maximum L/D Ratio

4 Chapter 4: Theory of Flight, Maneuvers & Stall Dynamics

4.1 Equilibrium of Forces in Steady Flight, Climb & Glide 4.2 Theory of the Turn, Load Factor & Flight Envelope 4.3 Stall Physics, Critical Angle of Attack & High-Lift Devices 4.4 Autorotation, Spin Awareness & Recovery Procedures

5 Chapter 5: High-Speed Airflow

5.1 Speed of Sound, Mach Number & Flight Regimes 5.2 Critical Mach Number, Shock Waves & Compressibility Buffet 5.3 Sweepback Effects, Area Rule, Aerodynamic Heating & High-Speed Intakes

6 Chapter 6: Flight Stability & Dynamic Characteristics

6.1 Fundamentals of Static & Dynamic Stability 6.2 Longitudinal Stability & Centre of Gravity Limits 6.3 Lateral & Directional Stability Mechanisms 6.4 Interrelationship of Stability: Dutch Roll & Spiral Instability

4.3 Stall Physics, Critical Angle of Attack & High-Lift Devices

Key Takeaways Explain This Topic AI

Aerodynamic stall occurs when the critical angle of attack (alpha_crit) is exceeded, leading to boundary layer separation, loss of upper-surface suction, and severe lift breakdown regardless of airspeed or pitch attitude.

Critical angle of attack is a fixed aerodynamic property for a given wing section, whereas stall speed (Vs) varies with gross weight, load factor, CG location, and environmental contamination (ice).

Trailing-edge high-lift devices (plain, split, slotted, Fowler flaps) increase maximum lift coefficient (CLmax) primarily by increasing wing camber and surface area, though Fowler flaps yield the largest CLmax gain with minimal initial drag.

Leading-edge high-lift devices (slats, slots, Krueger flaps) re-energize the upper surface boundary layer or increase leading-edge radius, delaying flow separation to higher angles of attack.

Last updated: July 2026

4.3 Stall Physics, Critical Angle of Attack & High-Lift Devices

An aerodynamic stall is one of the most critical phenomena in fluid dynamics and flight safety. EASA Part-66 Module 08 requires aircraft maintenance personnel to possess a thorough understanding of stall physics, boundary layer separation, variables altering stall speed, and the mechanical and aerodynamic principles of high-lift systems.

1. Mechanism of an Aerodynamic Stall

Lift is generated by producing a lower static pressure on the upper surface of the airfoil relative to the lower surface. As angle of attack ( α \alpha α ) increases, airflow over the upper surface accelerates, increasing suction and raising the lift coefficient ( C L C_L C L ​ ). Low Angle of Attack (Laminar Airflow) High Angle of Attack (Flow Separation / Stall)

  • ==================> =========--~~~~~ (Turbulent Wake)
  • /-----------\ /-----------\ |
  • -->( Airfoil ) -----> ( Airfoil ) v Separation Point
  • \-----------/ \-----------/
  • ==================> =================>
  • Adverse Pressure Gradient & Flow Separation

Beyond a certain angle of attack, air flowing along the upper surface must overcome an increasingly strong adverse pressure gradient (pressure rises from the point of maximum thickness toward the trailing edge).

At low angles of attack, boundary layer kinetic energy is sufficient to overcome this adverse gradient, keeping flow attached.

At high angles of attack, boundary layer friction depletes kinetic energy. The slow-moving boundary layer reverses direction, causing airflow separation from the upper surface.

As α \alpha α reaches the Critical Angle of Attack ( α crit \alpha_{\text{crit}} α crit ​ ) , the separation point shifts rapidly forward toward the leading edge. The organized low-pressure vortex structure collapses into a turbulent wake, resulting in a sudden drop in lift coefficient ( C L C_L C L ​ ) and a massive increase in pressure drag ( C D C_D C D ​ ). Stall Condition: α > α crit \text{Stall Condition:} \quad \alpha > \alpha_{\text{crit}} Stall Condition: α > α crit ​

Fundamental Rule for EASA Exams: An aircraft can stall at ANY airspeed, ANY pitch attitude, and ANY altitude if α crit \alpha_{\text{crit}} α crit ​ is exceeded.

In-Flight Warning Indicators

Buffeting: High-energy turbulent vortices shedding from the stalled main wing strike the horizontal tailplane, causing mechanical vibrations felt in the airframe and control column.

Sluggish Control Response: Depleted dynamic pressure over ailerons reduces roll effectiveness.

Synthetic Warnings: Stick shakers, angle-of-attack vanes, and artificial audio horns trigger before reaching α crit \alpha_{\text{crit}} α crit ​ .

2. Factors Influencing Stall Speed ( V s V_s V s ​ )

While α crit \alpha_{\text{crit}} α crit ​ is an intrinsic geometric property of a specific airfoil profile, the indicated stall speed ( V s V_s V s ​ ) varies based on several operational factors governed by the stall speed equation: V s = 2 W ρ S C L max ⁡ V_s = \sqrt{\frac{2 W}{\rho S C_{L\max}}} V s ​ = ρS C L m a x ​ 2 W ​ ​

Variable Change in Variable Effect on Stall Speed ( V s V_s V s ​ ) Physical Aerodynamic Cause

Aircraft Weight ( W W W ) Increase Increases ( V s ∝ W V_s \propto \sqrt{W} V s ​ ∝ W ​ ) Higher weight requires greater lift, reaching C L max ⁡ C_{L\max} C L m a x ​ at a higher airspeed.

Load Factor ( n n n ) Increase Increases ( V s ∝ n V_s \propto \sqrt{n} V s ​ ∝ n ​ ) Accelerated maneuvers require wing lift equal to n ⋅ W n \cdot W n ⋅ W .

Center of Gravity ( C G CG CG ) Forward Shift Increases Forward C G CG CG increases required tailplane downforce, raising total main wing lift demand.

Flap Deflection Deploy Flaps Decreases Extends surface area ( S S S ) and camber, significantly increasing C L max ⁡ C_{L\max} C L m a x ​ .

Wing Ice Contamination Frost/Ice Accumulation Dramatically Increases Roughness degrades boundary layer, reducing C L max ⁡ C_{L\max} C L m a x ​ and lowering α crit \alpha_{\text{crit}} α crit ​ by 3 ∘ − 5 ∘ 3^\circ - 5^\circ 3 ∘ − 5 ∘ .

3. High-Lift Devices: Trailing Edge Flaps

Trailing edge flaps modify wing section geometry to increase maximum lift coefficient ( C L max ⁡ C_{L\max} C L m a x ​ ), allowing lower approach and landing speeds. Plain Flap Split Flap Slotted Flap Fowler Flap

  • \-----\ \-----\ \-----\ \-----\ =\-----\
  • \ \ \---\ \--- \ \
  • v Deflection v Plate v Slot & Gap v Extended Gap
  • Comparison of Trailing Edge Flap Types

Plain Flap: Simple hinged rear wing section. Increases camber, moderate C L max ⁡ C_{L\max} C L m a x ​ gain, increases drag substantially.

Split Flap: Plate deflected from lower surface only. Creates high profile drag with moderate C L max ⁡ C_{L\max} C L m a x ​ gain; produces large pitch changes.

Slotted Flap: Features a high-pressure gap between main wing and flap. High-pressure air from beneath passes through the slot, re-energizing the upper boundary layer and delaying local separation.

Fowler Flap: Moves rearward along track guides before curving downward. Increases both wing surface area ( S S S ) and camber . Delivers the highest increase in C L max ⁡ C_{L\max} C L m a x ​ with minimal initial drag penalty at partial deflections.

4. High-Lift Devices: Leading Edge Systems

Leading edge high-lift systems maintain attached airflow at extreme angles of attack. Leading-Edge Slot / Slat Krueger Flap

  • /---\ /------------\ /---\------------\
  • ( Slat) ( Main Wing ) ( / Main Wing )
  • \---/ \------------/ \/---------------/
  • ^ Converging Slot Gap ^ Deflected Lower Plate
  • Slats and Fixed Slots

Slot Principle: A narrow gap near the leading edge permits high-pressure air from underneath the wing to flow to the upper surface. This re-energizes the boundary layer, delaying separation.

Automatic Slats: Movable aerofoil segments positioned at the leading edge. At low angles of attack, aerodynamic pressure holds them flush. At high α \alpha α , low pressure at the leading edge pulls the slats forward automatically on tracks, opening a slot and increasing α crit \alpha_{\text{crit}} α crit ​ from 15 ∘ 15^\circ 1 5 ∘ up to 25 ∘ 25^\circ 2 5 ∘ or more.

Krueger Flaps: Hinged structures deflected forward and downward from the lower leading edge, increasing leading-edge radius and effective camber on swept-wing transport aircraft.