Study guide
6.1 High-Pressure & Very-High-Pressure Classification
EPA Section 608 Universal Refrigerant Certification Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 EPA 608 Universal Exam Facts 1.2 How the Universal Exam Works & How to Study 1.3 Title VI, the Clean Air Act & Why Certification Exists
2 Core: Ozone Science & Regulatory Foundations
2.1 Stratospheric Ozone Depletion & Refrigerant Chemistry 2.2 The Clean Air Act, Montreal Protocol & Venting Prohibition 2.3 Section 608 Regulatory Framework 2.4 Substitute Refrigerants, Blends & Lubricant Compatibility
3 Core: Recovery, Reclamation & Recordkeeping
3.1 The Three R's & Recovery Technique Fundamentals 3.2 Recovery Equipment Certification & the Sales Restriction 3.3 Recordkeeping & Leak Repair Requirements 3.4 Refrigeration Cycle, Gauges & Evacuation Fundamentals
4 Core: Safety, Cylinders & Leak Detection
4.1 Refrigerant Exposure Hazards & PPE 4.2 Recovery Cylinders, Fill Limits & Shipping 4.3 Leak Detection Methods & Nitrogen Use
5 Type I: Small Appliances
5.1 Small Appliance Classification & the 1993 Dividing Line 5.2 Type I Recovery Requirements 5.3 Recovery Techniques, Access Valves & Passive Devices 5.4 Refrigerant Identification, Leak Detection & Safety
6 Type II: Classification, Evacuation & Recovery
6.1 High-Pressure & Very-High-Pressure Classification 6.2 Type II Evacuation Requirements by Charge Size 6.3 Type II Recovery Techniques & Efficiency
7 Type II: Leak Management & Safety
7.1 Leak-Rate Thresholds & Repair Duty 7.2 Type II Leak Detection Methods & Test Pressure 7.3 Type II Safety Requirements
8 Type III: Classification, Evacuation & Recovery
8.1 Low-Pressure Classification & Purge Units 8.2 Type III Evacuation Requirements 8.3 Type III Recovery Techniques
9 Type III: Recharging, Leak Testing & Safety
9.1 Type III Recharging Techniques 9.2 Leak Testing, Pressurization & Purge Operation 9.3 Type III Safety Requirements
10 Exam Strategy & Final Review
10.1 Cross-Section Comparison & Common Traps 10.2 Test-Day Logistics & Retake Policy 10.3 Final Review Checklist & Study Plan
6.1 High-Pressure & Very-High-Pressure Classification
Key Takeaways Explain This Topic AI
Medium-pressure appliances use refrigerants with a liquid-phase saturation pressure between 45 and 170 psia at 104°F, including R-12, R-114, R-124, R-134a, and R-500 — R-134a is a common exam trap since it's often mistaken for a high-pressure refrigerant
High-pressure appliances (170-355 psia at 104°F, e.g. R-22, R-410A, R-404A, R-507A) and very-high-pressure appliances (critical temp below 104°F or above 355 psia, e.g. R-13, R-503, CO2) are the other two Type II pressure bands
Type II certification covers medium-, high-, and very-high-pressure appliances — split systems, RTUs, water-source heat pumps, ice machines, and supermarket racks — not small sealed appliances (Type I) or low-pressure chillers (Type III)
Core Type II components include the condenser, receiver, liquid line, evaporator, and accumulator
- The Type II section accounts for 25 of the 100 questions on the EPA Universal 608 exam
- Last updated: July 2026
6.1 High-Pressure & Very-High-Pressure Classification
Quick Answer: Type II certification — one quarter of the 100-question EPA Section 608 Universal exam — authorizes you to service, maintain, repair, and dispose of medium-pressure , high-pressure , and very-high-pressure appliances : everything from older R-134a and R-12 equipment through residential split systems, rooftop package units, and supermarket refrigeration racks. It does not cover small factory-sealed appliances holding 5 pounds or less of refrigerant (that's Type I) or low-pressure chillers that operate below atmospheric pressure through most of the circuit (that's Type III).
The Type II section of the Universal exam is built around one core skill: correctly recognizing which pressure category an appliance falls into, because that classification drives almost every other rule you'll apply in the field — required evacuation levels, allowed recovery equipment, and even recordkeeping. Under 40 CFR 82.152 , EPA defines appliance categories by the refrigerant's physical properties, not by the size of the building it's installed in or how much the equipment costs.
The Three Type II Pressure Categories
Medium-pressure appliance — an appliance that uses a refrigerant with a liquid-phase saturation pressure between 45 psia and 170 psia at 104°F . The regulation's named examples are R-12 , R-114 , R-124 , R-134a , and R-500 . This is the category candidates most often get wrong on the exam: because R-134a replaced R-12 in automotive and many commercial applications and 'feels' like a modern high-pressure refrigerant, test-takers frequently misclassify it as high-pressure. R-134a is medium-pressure, not high-pressure — remember that pairing specifically for the exam.
High-pressure appliance — an appliance that uses a refrigerant with a liquid-phase saturation pressure between 170 psia and 355 psia at 104°F . This is the pressure band that covers the overwhelming majority of commercial and residential air-conditioning and refrigeration equipment you'll encounter as a technician. The regulation's own examples include R-22 , R-407A , R-407C , and R-410A ; in the field you'll also service R-404A and R-507A systems, since both refrigerants fall in the same saturation-pressure range and dominate supermarket case and walk-in cooler racks.
Very high-pressure appliance — an appliance that uses a refrigerant with either a critical temperature below 104°F or a liquid-phase saturation pressure above 355 psia at 104°F . The regulation's named examples are R-13 , R-23 , R-503 , R-508A , and R-508B — refrigerants used almost exclusively in the low-temperature stage of cascade refrigeration systems. CO2 (R-744) , which has a critical temperature of about 87.8°F, also meets the 'critical temperature below 104°F' test. That's why transcritical CO2 supermarket racks are treated as very-high-pressure appliances for evacuation and recovery purposes, even though CO2 itself is nontoxic and nonflammable.
- Refrigerant Classification Typical Application
- R-12 Medium-pressure Legacy automotive, older refrigeration
- R-114 Medium-pressure Legacy centrifugal/rotary compressors
- R-124 Medium-pressure Legacy chillers, blends
- R-134a Medium-pressure Automotive A/C, some commercial refrigeration
- R-500 Medium-pressure Legacy commercial A/C
- R-22 High-pressure Legacy split systems, RTUs
- R-410A High-pressure Modern split systems, RTUs
- R-404A High-pressure Supermarket cases, walk-ins
- R-507A High-pressure Supermarket racks, walk-ins
- R-13 / R-23 / R-503 Very high-pressure Low-temp cascade systems
- CO2 (R-744) Very high-pressure Transcritical supermarket racks
- Core Components on Type II Equipment
Because Type II spans everything from a 2-ton split system to a multiplex supermarket rack, the exam expects you to know where refrigerant physically sits in the circuit at any given moment:
Condenser — rejects the heat absorbed in the evaporator; refrigerant desuperheats, condenses, and is often subcooled here.
Receiver — a storage vessel downstream of the condenser that holds excess liquid refrigerant to handle varying load conditions, and gives technicians a place to isolate the charge for component service (see the pump-down discussion in Section 6.3).
Liquid line — carries subcooled liquid refrigerant from the receiver (or condenser outlet) to the metering device; filter-driers are typically installed here.
Evaporator — absorbs heat from the conditioned space or refrigerated product as the refrigerant boils from liquid to vapor at low pressure.
Accumulator — installed in the suction line ahead of the compressor on many systems to trap any un-evaporated liquid refrigerant and oil, protecting the compressor from slugging damage.
What Type II Covers — and What It Doesn't
Type II certification lets you work on split-system air conditioners and heat pumps, rooftop package units (RTUs), water-source heat pumps, ice machines, reach-in and walk-in coolers/freezers, and supermarket compressor racks — essentially any reciprocating, scroll, or screw-compressor system charged with a medium-pressure, high-pressure, or very-high-pressure refrigerant. It does not authorize you to service:
Small appliances — factory-sealed units normally charged with 5 pounds or less of refrigerant (household refrigerators, window units, vending machines, small water coolers). These require Type I certification instead, regardless of the refrigerant's pressure classification.
Low-pressure appliances — typically large centrifugal chillers using refrigerants such as R-11, R-113, R-123, or R-514A that operate below atmospheric pressure through most of the circuit. These require Type III certification.
Exam scenarios often test this boundary directly. A question describing a 3-ton rooftop unit charged with R-410A is Type II territory. A question describing a household refrigerator is testing whether you route it to Type I instead, and a question describing a large building's centrifugal chiller is testing whether you know to route it to Type III. The diagram below summarizes the decision path.
Why the Exam Emphasizes Pressure, Not Size
New technicians often assume EPA licensing follows the size or cost of the equipment — a home AC unit feels 'small' compared to a supermarket rack, so it's tempting to guess that size drives the certification category. The exam intentionally tests against that assumption. A 1.5-ton residential split system and a 40-ton rooftop unit are both high-pressure appliances requiring Type II, because both use a refrigerant in the same 170-355 psia saturation-pressure band — the size of the box has nothing to do with it. The only size-based carve-out in the entire Section 608 program is the small-appliance definition (factory-sealed, 5 lb or less), which routes to Type I regardless of the refrigerant used. Once you're past that carve-out and past the low-pressure chiller carve-out for Type III, everything else sorts purely by the refrigerant's saturation pressure and critical temperature.
This matters because a single job site can mix categories. A convenience store might have a small factory-sealed reach-in beverage cooler (Type I), a walk-in freezer rack running R-404A (Type II), and — much less commonly — a low-pressure chiller serving the HVAC system (Type III). A technician holding only a Type I card cannot legally open the R-404A rack, even though it sits in the same building and looks similar to equipment they're licensed to service. Universal certification, which requires passing the Core exam plus all three type exams, is what allows a technician to move freely between all of these appliance categories on the same service call.