Study guide
8.2 Type III Evacuation Requirements
EPA Section 608 Universal Refrigerant Certification Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 EPA 608 Universal Exam Facts 1.2 How the Universal Exam Works & How to Study 1.3 Title VI, the Clean Air Act & Why Certification Exists
2 Core: Ozone Science & Regulatory Foundations
2.1 Stratospheric Ozone Depletion & Refrigerant Chemistry 2.2 The Clean Air Act, Montreal Protocol & Venting Prohibition 2.3 Section 608 Regulatory Framework 2.4 Substitute Refrigerants, Blends & Lubricant Compatibility
3 Core: Recovery, Reclamation & Recordkeeping
3.1 The Three R's & Recovery Technique Fundamentals 3.2 Recovery Equipment Certification & the Sales Restriction 3.3 Recordkeeping & Leak Repair Requirements 3.4 Refrigeration Cycle, Gauges & Evacuation Fundamentals
4 Core: Safety, Cylinders & Leak Detection
4.1 Refrigerant Exposure Hazards & PPE 4.2 Recovery Cylinders, Fill Limits & Shipping 4.3 Leak Detection Methods & Nitrogen Use
5 Type I: Small Appliances
5.1 Small Appliance Classification & the 1993 Dividing Line 5.2 Type I Recovery Requirements 5.3 Recovery Techniques, Access Valves & Passive Devices 5.4 Refrigerant Identification, Leak Detection & Safety
6 Type II: Classification, Evacuation & Recovery
6.1 High-Pressure & Very-High-Pressure Classification 6.2 Type II Evacuation Requirements by Charge Size 6.3 Type II Recovery Techniques & Efficiency
7 Type II: Leak Management & Safety
7.1 Leak-Rate Thresholds & Repair Duty 7.2 Type II Leak Detection Methods & Test Pressure 7.3 Type II Safety Requirements
8 Type III: Classification, Evacuation & Recovery
8.1 Low-Pressure Classification & Purge Units 8.2 Type III Evacuation Requirements 8.3 Type III Recovery Techniques
9 Type III: Recharging, Leak Testing & Safety
9.1 Type III Recharging Techniques 9.2 Leak Testing, Pressurization & Purge Operation 9.3 Type III Safety Requirements
10 Exam Strategy & Final Review
10.1 Cross-Section Comparison & Common Traps 10.2 Test-Day Logistics & Retake Policy 10.3 Final Review Checklist & Study Plan
8.2 Type III Evacuation Requirements
Key Takeaways Explain This Topic AI
EPA requires low-pressure appliances to be evacuated to 25 mm Hg absolute when using recovery equipment - a measurement taken from a perfect vacuum, not a vacuum reading relative to atmospheric pressure.
The classic Type III exam trap is confusing '25 mm Hg absolute' with '25 inches of Hg vacuum' - the two are not remotely equivalent, and mistaking one for the other leaves far too much air and moisture inside the system.
For a non-major repair on a low-pressure appliance, a technician may pressurize the system to no higher than 0 psig before opening it, and is not required to evacuate the system to the standard level again before returning it to service.
A major repair on a low-pressure appliance still requires evacuation to the standard 25 mm Hg absolute level before the system is opened and again before it is returned to service.
Pulling a low-pressure chiller down to a deep vacuum lowers the refrigerant's saturation temperature dramatically, creating a real risk that water still present in the evaporator or condenser tubes will freeze and split the tubes.
Last updated: July 2026
Type III Evacuation Requirements
Once a low-pressure appliance's refrigerant charge has been recovered, EPA Section 608 sets a specific target for how completely the system must be evacuated before it can be opened for repair or returned to service. Unlike Type I (which uses inches of Hg vacuum) or Type II (which uses a mix of psig and inches of Hg vacuum depending on charge size), Type III uses a unit of measurement that trips up technicians and exam-takers more than almost any other single number on the Universal exam.
The 25 mm Hg Absolute Standard
For a low-pressure appliance, using recovery equipment, EPA requires evacuation to 25 millimeters of mercury (mm Hg) absolute . That is the standard EPA table value a Type III technician must hit before a low-pressure system can be considered adequately evacuated.
The word absolute is doing all the work in that sentence, and it is the source of the classic exam trap covered below. An absolute pressure reading is measured from a perfect vacuum (zero) upward - it tells you how much pressure is actually still inside the vessel, full stop. That is a fundamentally different scale from the vacuum reading most technicians are used to seeing on a gauge day to day.
The Classic Trap: mm Hg Absolute vs. Inches of Hg Vacuum
Most technicians are far more familiar with inches of mercury (in. Hg) vacuum - the scale used elsewhere in Section 608 (for example, Type I's 4 in. Hg vacuum standard) - which is measured relative to atmospheric pressure , with 0 in. Hg vacuum meaning "at atmospheric pressure" and higher numbers meaning progressively deeper vacuum. A technician who sees the number "25" in a Type III context and assumes it must mean "25 inches of Hg vacuum" - because that is the pattern their brain has learned from Type I and Type II - will badly under-evacuate a low-pressure system, and possibly answer the exam question incorrectly as well.
Reading Reference point Approximate equivalent What it actually means for a low-pressure appliance
25 mm Hg absolute (the correct EPA standard) Measured from a perfect vacuum (0) Roughly 0.98 in. Hg absolute, or about 28.9 in. Hg vacuum on a compound gauge A deep, thorough evacuation - very little gas remains inside the vessel
25 in. Hg vacuum (the common misreading) Measured relative to atmospheric pressure Roughly 4.92 in. Hg absolute, or about 125 mm Hg absolute Stops evacuation roughly five times too early - leaves far more air and moisture inside than the standard permits
Notice how far apart those two numbers actually are once converted to the same scale: the correct standard (25 mm Hg absolute) corresponds to an extremely deep vacuum near 28.9 in. Hg on a vacuum gauge, while the commonly confused figure (25 in. Hg vacuum) corresponds to roughly 125 mm Hg absolute - about five times higher (meaning far less complete) than what the appliance actually requires. A technician who stops at 25 in. Hg vacuum, thinking that satisfies "the 25 mm Hg standard," has left the system with dramatically more residual air and moisture than EPA requires removed. Whenever a Type III exam question gives you a number for evacuation, read the unit label first - "mm Hg absolute" and "in. Hg vacuum" are never interchangeable, and the exam is written to test exactly that distinction.