Study guide
6.2 Recovery Equipment Requirements
EPA 608 Technician Certification Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction to EPA 608 Certification
1.1 What EPA 608 Is and Who Needs It 1.2 Exam Format, Scoring, and Administration 1.3 How to Study for EPA 608
2 Regulations and the Clean Air Act
2.1 Clean Air Act Overview 2.2 Penalties and Enforcement 2.3 Montreal Protocol and International Agreements 2.4 AIM Act and HFC Phasedown Schedule 2.5 SNAP Program and Refrigerant Transitions
3 Refrigerants and Ozone Science
3.1 The Science of Ozone Depletion (ODP and GWP) 3.2 Refrigerant Classification, ASHRAE Numbering, and Safety Groups 3.3 Common Refrigerants: Properties, Applications, and Phaseout Status 3.4 Refrigerant Blends: Glide, Fractionation, and Liquid Charging
4 The Refrigeration Cycle
4.1 The Basic Refrigeration Cycle 4.2 System Components in Detail 4.3 Heat Transfer and Pressure-Temperature Relationships
5 Refrigerant Safety and Handling
5.1 Refrigerant Hazards and Health Effects 5.2 Safe Handling Practices, PPE, and Cylinders 5.3 A2L (Mildly Flammable) Refrigerant Safety
6 Recovery, Recycling, and Reclaiming
6.1 The Three Rs: Recover, Recycle, Reclaim 6.2 Recovery Equipment Requirements 6.3 Required Levels of Evacuation 6.4 Refrigerant Sales Restrictions and Recordkeeping
7 Leak Detection and Repair
7.1 Leak Detection Methods 7.2 Leak Repair Requirements and Trigger Rates 7.3 Leak-Rate Calculation, Recordkeeping, and Reporting
8 Type I — Small Appliances
8.1 What Counts as a Small Appliance 8.2 Type I Recovery Requirements 8.3 Type I Procedures, Access Valves, and the Open-Book Exam
9 Type II — High-Pressure Appliances
9.1 What Type II Covers: High-Pressure System Overview 9.2 Type II Recovery Methods and Required Evacuation Levels 9.3 Leak Detection, the Repair Triggers, and Recordkeeping 9.4 The R-22 Phaseout, Retrofits, and the Move to Lower-GWP A2Ls
10 Type III — Low-Pressure Appliances
10.1 Low-Pressure System Fundamentals 10.2 Purge Units and Air Management 10.3 Type III Recovery and Procedures 10.4 Type III Leak Testing
11 10. Disposal, Shipping, and Compliance
11.1 Equipment Disposal Requirements 11.2 Refrigerant Shipping and Transport 11.3 Compliance Checklist and Best Practices
12 Final Review and Exam Strategy
12.1 High-Yield Core Section Review 12.2 Type I vs Type II vs Type III: Side-by-Side Review 12.3 How the Exam Works and Exam-Day Strategy
6.2 Recovery Equipment Requirements
Key Takeaways Explain This Topic AI
Recovery/recycling equipment must be certified by an EPA-approved testing organization — AHRI or UL — and labeled accordingly
Self-contained (active) equipment has its own compressor and no size limit; system-dependent (passive) equipment is limited to appliances of 15 lb or less
Small-appliance recovery with equipment made on or after November 15, 1993 requires 90% of the charge with the compressor operating or 80% with it not operating (80% with older equipment), or a 4-inch Hg vacuum either way
November 15, 1993 is the key equipment grandfather date; Appendix B3/B4 protocols apply to machines made on or after January 1, 2017
Recovered refrigerant goes into refillable DOT-approved cylinders filled no more than 80%; refilling disposable DOT-39 cylinders is illegal
Last updated: October 2026
Why Equipment Certification Matters
You cannot legally pull refrigerant with just any vacuum pump. Under 40 CFR Part 82, Subpart F, all recovery and recycling equipment must be certified by an EPA-approved testing organization before it can be sold or used. EPA has approved two such organizations: the Air-Conditioning, Heating, and Refrigeration Institute (AHRI) and Underwriters Laboratories (UL) .
Certified machines carry a label reading, in effect, "This equipment has been certified by AHRI/UL to meet EPA's minimum requirements for recovery/recycling equipment intended for use with [appliance category]." Expect the exam to ask which organizations certify equipment — the answer is AHRI and UL, not EPA itself and not DOT.
The certification proves the machine can pull refrigerant down to the legally required recovery levels. Machines are tested against a version of the AHRI 740 test protocol , and the exact appendix depends on the manufacturing date — this is the "grandfather" structure the exam loves to probe.
Equipment Grandfather Dates
- Manufacturing Date Governing Standard What It Means
- Before Nov 15, 1993 Original EPA performance rules "Old" equipment; lower required vacuum levels apply
- On/after Nov 15, 1993 ARI/AHRI 740 (Appendix B1, then B2) "New" equipment; deeper required vacuum levels apply
On/after Jan 1, 2017 Appendix B3 (non-flammable) or B4 (flammable) Updated protocols adding A2L/flammable-refrigerant testing
The date November 15, 1993 is the single most-tested cutoff in this chapter. Equipment built on or after that date must reach deeper evacuation levels than older machines, because the technology had improved. The 2017 split into Appendix B3 (non-flammable) and B4 (flammable) was added so machines could be certified to handle newer A2L mildly flammable refrigerants such as R-32 and R-454B safely.
Self-Contained vs. System-Dependent Recovery
EPA recognizes two fundamentally different machine architectures, and the difference controls what size system you may legally service with each .
Self-Contained (Active) Recovery Equipment
Has its own compressor or pump and can pull refrigerant out without any help from the appliance .
Works whether or not the appliance's own compressor still runs.
Faster, more reliable, and required for larger systems.
No upper size limit — may be used on appliances of any charge.
System-Dependent (Passive) Recovery Equipment
Has no compressor of its own ; it relies on the appliance's pressure or the appliance's own compressor to push refrigerant into the recovery container.
Cheaper and simpler, but slower and useless if the system has no pressure and a dead compressor (then only gravity/liquid recovery works).
Legally limited to appliances containing 15 pounds of refrigerant or less.
This 15-pound ceiling is a frequently tested fact: you may never use system-dependent equipment on an appliance with more than 15 lb of refrigerant. Above that, a self-contained machine is mandatory.
Recovery on Small Appliances vs. Larger Systems
A small appliance is any product fully manufactured, charged, and hermetically sealed in a factory with 5 pounds or less of refrigerant — household refrigerators and freezers, window and PTAC room air conditioners, dehumidifiers, drinking-water coolers, vending machines, and under-counter ice makers. Recovery requirements for small appliances are stated as a recovery efficiency , not a single vacuum number:
Compressor operating (working), recovery equipment made on or after November 15, 1993: recover 90% of the refrigerant, or reach a 4-inch Hg vacuum .
Compressor not operating (inoperative): recover 80% of the refrigerant, or reach a 4-inch Hg vacuum .
Recovery equipment made before November 15, 1993: recover 80% whether or not the compressor works, or reach a 4-inch Hg vacuum .
A handy memory hook: a working compressor helps , so you can pull more out — 90% . A dead compressor makes recovery harder — only 80% is required. Larger (non-small) appliances are not measured by a percentage; they are evacuated to the inches-of-mercury levels covered in Section 5.3.
Recovery Equipment Quick Reference
- Equipment / Item Requirement
- Certifying bodies AHRI and UL (EPA-approved testing organizations)
- Self-contained (active) Own compressor; no size limit
- System-dependent (passive) Relies on appliance; ≤ 15 lb only
- Small appliance, compressor ON 90% recovery (1993+ equipment; 80% with older) or 4 in. Hg vacuum
- Small appliance, compressor OFF 80% recovery or 4 in. Hg vacuum
- Recovery cylinder DOT-approved, refillable; fill ≤ 80% liquid; hydrostatic test every 5 years
- Disposable (DOT-39) cylinder Single-use; illegal to refill
Example: A technician must recover R-134a from an inoperative household refrigerator (nameplate charge listed). Because the compressor is dead, the machine must achieve either 80% of the nameplate charge or a 4-inch Hg vacuum — meeting either one satisfies the rule. If that same refrigerator's compressor were still running and the recovery machine was made on or after November 15, 1993, the bar would rise to 90% or 4-inch Hg vacuum .
For the Exam: Equipment is certified by AHRI or UL ; system-dependent machines are capped at 15 lb ; small-appliance recovery is 90% (compressor on, 1993+ equipment) / 80% (compressor off or older equipment), or 4 in. Hg either way; never refill a DOT-39 disposable cylinder, and never fill any recovery cylinder past 80% .