Study guide

7.2 Leak Repair Requirements and Trigger Rates

EPA 608 Technician Certification Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction to EPA 608 Certification

1.1 What EPA 608 Is and Who Needs It 1.2 Exam Format, Scoring, and Administration 1.3 How to Study for EPA 608

2 Regulations and the Clean Air Act

2.1 Clean Air Act Overview 2.2 Penalties and Enforcement 2.3 Montreal Protocol and International Agreements 2.4 AIM Act and HFC Phasedown Schedule 2.5 SNAP Program and Refrigerant Transitions

3 Refrigerants and Ozone Science

3.1 The Science of Ozone Depletion (ODP and GWP) 3.2 Refrigerant Classification, ASHRAE Numbering, and Safety Groups 3.3 Common Refrigerants: Properties, Applications, and Phaseout Status 3.4 Refrigerant Blends: Glide, Fractionation, and Liquid Charging

4 The Refrigeration Cycle

4.1 The Basic Refrigeration Cycle 4.2 System Components in Detail 4.3 Heat Transfer and Pressure-Temperature Relationships

5 Refrigerant Safety and Handling

5.1 Refrigerant Hazards and Health Effects 5.2 Safe Handling Practices, PPE, and Cylinders 5.3 A2L (Mildly Flammable) Refrigerant Safety

6 Recovery, Recycling, and Reclaiming

6.1 The Three Rs: Recover, Recycle, Reclaim 6.2 Recovery Equipment Requirements 6.3 Required Levels of Evacuation 6.4 Refrigerant Sales Restrictions and Recordkeeping

7 Leak Detection and Repair

7.1 Leak Detection Methods 7.2 Leak Repair Requirements and Trigger Rates 7.3 Leak-Rate Calculation, Recordkeeping, and Reporting

8 Type I — Small Appliances

8.1 What Counts as a Small Appliance 8.2 Type I Recovery Requirements 8.3 Type I Procedures, Access Valves, and the Open-Book Exam

9 Type II — High-Pressure Appliances

9.1 What Type II Covers: High-Pressure System Overview 9.2 Type II Recovery Methods and Required Evacuation Levels 9.3 Leak Detection, the Repair Triggers, and Recordkeeping 9.4 The R-22 Phaseout, Retrofits, and the Move to Lower-GWP A2Ls

10 Type III — Low-Pressure Appliances

10.1 Low-Pressure System Fundamentals 10.2 Purge Units and Air Management 10.3 Type III Recovery and Procedures 10.4 Type III Leak Testing

11 10. Disposal, Shipping, and Compliance

11.1 Equipment Disposal Requirements 11.2 Refrigerant Shipping and Transport 11.3 Compliance Checklist and Best Practices

12 Final Review and Exam Strategy

12.1 High-Yield Core Section Review 12.2 Type I vs Type II vs Type III: Side-by-Side Review 12.3 How the Exam Works and Exam-Day Strategy

7.2 Leak Repair Requirements and Trigger Rates

Key Takeaways Explain This Topic AI

Leak repair is mandatory once a covered appliance EXCEEDS its threshold: 10% comfort cooling, 20% commercial refrigeration, 30% industrial process refrigeration, expressed as percent of full charge per year

Repairs must be completed within 30 days of the refrigerant addition that shows the rate is exceeded (120 days if an industrial-process shutdown is required; more time is allowed for unavailable parts, other regulations, or mothballing) and must bring the leak rate back BELOW the threshold

Both an initial AND a follow-up verification test are required at the conclusion of each repair to confirm it worked

The ODS rule (40 CFR 82, Subpart F) covers appliances with a 50+ lb charge; the 2024 HFC ER&R rule (40 CFR 84.106) covers 15+ lb HFC appliances starting January 1, 2026, excluding residential and light commercial AC and heat pumps

If a leak cannot be fixed, the owner must create a retrofit-or-retirement plan within 30 days and complete it within one year

Last updated: October 2026

The Trigger Rates Are the Single Most-Tested Numbers

EPA Section 608 does not require that an appliance never leak. It requires that, once an appliance's calculated annual leak rate exceeds a threshold tied to how the appliance is used, the owner or operator must act. These three trigger (threshold) leak rates appear on nearly every Type II exam form, so commit them to memory:

Appliance use Threshold leak rate (% of full charge / year)

Comfort cooling (human-comfort AC, plus refrigerated transport and other non-IPR/non-commercial appliances) 10%

  • Commercial refrigeration (supermarkets, restaurants, cold storage) 20%
  • Industrial process refrigeration (IPR) (chemical, manufacturing process loads) 30%

A memory hook: the more critical and harder-to-shut-down the process, the higher the tolerated rate — comfort cooling 10, commercial 20, industrial 30. The rates are annualized (see Section 6.3): a system can trip the rule even if the technician only watched it for a few weeks, because the loss is projected to a full 12 months.

Which Appliances Are Covered

Coverage depends on charge size and refrigerant type, and this is where the HFC rule that took effect in 2026 matters:

Legacy ODS rule — 40 CFR Part 82, Subpart F: applies to appliances normally containing a full charge of 50 or more pounds of an ozone-depleting refrigerant (e.g., R-22, R-11, R-123).

HFC rule — 40 CFR 84.106 (2024 Emissions Reduction & Reclamation, ER&R, rule): beginning January 1, 2026 , the same leak-repair framework applies to appliances with a charge of 15 or more pounds of an HFC or certain HFC substitutes (e.g., R-410A, R-404A, R-448A). Two important carve-outs: the residential and light-commercial AC and heat-pump subsector is exempt , and substitutes with a GWP/exchange value of 53 or below are not covered.

The 30-Day Repair Clock

Once a leak-rate calculation done at the time refrigerant is added shows the appliance is over threshold, the owner/operator must identify and repair the leaks within 30 days of that determination. The repair must bring the leak rate back below the applicable threshold — a partial fix that still leaves the system over 10/20/30% is not compliant.

The deadline extends to 120 days where an industrial-process shutdown is required to make the repair.

More time is allowed when needed repair parts are unavailable, when other federal, state, or local rules make a timely repair impossible, or in radiological-contamination areas (some extensions must be requested from EPA).

The clock is suspended while the appliance is mothballed (evacuated and shut down).

Verification Tests: Initial AND Follow-Up

A repair is not "done" until it is proven. EPA requires two verification tests at the conclusion of repair efforts for each leak repaired:

Initial verification test — performed while the relevant components are still open/at the repair, confirming the specific leak is sealed (e.g., a pressure or electronic test on the repaired joint).

Follow-up verification test — performed after the appliance is brought back to normal operating characteristics and conditions , confirming the repair holds under real running pressures and temperatures.

If either test shows the repair failed, the owner may perform additional repairs and additional initial/follow-up tests within the allowed time window until the appliance is below threshold.

When Repair Fails: Retrofit or Retire

If the leaks cannot be repaired — or the owner simply chooses not to repair — a retrofit-or-retirement plan is required:

The plan must be created within 30 days of deciding to retrofit/retire, of failing to act on the leak, or of the appliance continuing to leak above threshold after repairs and verification.

The plan must include a schedule to complete the retrofit or retirement within one year of the plan's date.

Owners may request additional time, or ask EPA to be relieved of the plan, if defined conditions are met.

Leak Inspections After a Trigger

Under both Part 82 (ODS appliances of 50 lb or more) and Part 84 (HFC appliances of 15 lb or more), an appliance found over threshold also enters a periodic leak-inspection schedule until it stays clean:

  • Appliance Inspection frequency until "clean"
  • Commercial refrigeration / IPR, 500+ lb charge Every 3 months , until below threshold for 4 quarters in a row

Commercial refrigeration / IPR, under 500 lb (down to 50 lb ODS / 15 lb HFC) Once per year , until below threshold for one year

Comfort cooling and other non-IPR/non-commercial appliances Once per year , until below threshold for one year

Example: A supermarket rack holds 800 lb of R-448A (commercial refrigeration, 20% threshold). A leak-rate calculation at the last top-off comes out at 26%, over the 20% limit. The owner must repair within 30 days, run an initial and a follow-up verification test, and — because the charge is 500+ lb — inspect the rack every 3 months until it logs four consecutive quarters under 20%. If the rack keeps leaking above 20% after repair attempts, the owner has 30 days to write a retrofit-or-retirement plan and one year to finish it.

Mandatory Leak-Repair Trigger Rates by Appliance Use (% of full charge per year)