Study guide

8.2 Type I Recovery Requirements

EPA 608 Technician Certification Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction to EPA 608 Certification

1.1 What EPA 608 Is and Who Needs It 1.2 Exam Format, Scoring, and Administration 1.3 How to Study for EPA 608

2 Regulations and the Clean Air Act

2.1 Clean Air Act Overview 2.2 Penalties and Enforcement 2.3 Montreal Protocol and International Agreements 2.4 AIM Act and HFC Phasedown Schedule 2.5 SNAP Program and Refrigerant Transitions

3 Refrigerants and Ozone Science

3.1 The Science of Ozone Depletion (ODP and GWP) 3.2 Refrigerant Classification, ASHRAE Numbering, and Safety Groups 3.3 Common Refrigerants: Properties, Applications, and Phaseout Status 3.4 Refrigerant Blends: Glide, Fractionation, and Liquid Charging

4 The Refrigeration Cycle

4.1 The Basic Refrigeration Cycle 4.2 System Components in Detail 4.3 Heat Transfer and Pressure-Temperature Relationships

5 Refrigerant Safety and Handling

5.1 Refrigerant Hazards and Health Effects 5.2 Safe Handling Practices, PPE, and Cylinders 5.3 A2L (Mildly Flammable) Refrigerant Safety

6 Recovery, Recycling, and Reclaiming

6.1 The Three Rs: Recover, Recycle, Reclaim 6.2 Recovery Equipment Requirements 6.3 Required Levels of Evacuation 6.4 Refrigerant Sales Restrictions and Recordkeeping

7 Leak Detection and Repair

7.1 Leak Detection Methods 7.2 Leak Repair Requirements and Trigger Rates 7.3 Leak-Rate Calculation, Recordkeeping, and Reporting

8 Type I — Small Appliances

8.1 What Counts as a Small Appliance 8.2 Type I Recovery Requirements 8.3 Type I Procedures, Access Valves, and the Open-Book Exam

9 Type II — High-Pressure Appliances

9.1 What Type II Covers: High-Pressure System Overview 9.2 Type II Recovery Methods and Required Evacuation Levels 9.3 Leak Detection, the Repair Triggers, and Recordkeeping 9.4 The R-22 Phaseout, Retrofits, and the Move to Lower-GWP A2Ls

10 Type III — Low-Pressure Appliances

10.1 Low-Pressure System Fundamentals 10.2 Purge Units and Air Management 10.3 Type III Recovery and Procedures 10.4 Type III Leak Testing

11 10. Disposal, Shipping, and Compliance

11.1 Equipment Disposal Requirements 11.2 Refrigerant Shipping and Transport 11.3 Compliance Checklist and Best Practices

12 Final Review and Exam Strategy

12.1 High-Yield Core Section Review 12.2 Type I vs Type II vs Type III: Side-by-Side Review 12.3 How the Exam Works and Exam-Day Strategy

8.2 Type I Recovery Requirements

Key Takeaways Explain This Topic AI

With recovery equipment made on or after November 15, 1993: compressor functional, recover 90% of the charge; compressor not functional, recover 80% (older equipment: 80% either way) — OR evacuate to a 4-inch Hg vacuum in every case

System-dependent (passive) recovery uses the appliance's own pressure or compressor and is prohibited on appliances holding more than 15 lbs

Self-contained (active) recovery uses its own compressor and works regardless of whether the appliance compressor runs

Heat the compressor with a blanket or heat gun (never an open flame) and tap it with a rubber mallet to free refrigerant dissolved in oil

Refrigerant must be recovered before disposal, and the last person in the disposal chain is responsible for ensuring it happened

Last updated: October 2026

The Two Recovery Targets You Must Memorize

The single most-tested fact in Type I is the recovery requirement, and it has two moving parts: the required percentage depends on whether the appliance's own compressor still works and on when the recovery equipment was made. Get this table locked in cold.

Situation Recovery requirement Alternative

Equipment made on/after Nov 15, 1993, compressor IS functional Recover 90% of the refrigerant OR pull a 4-inch Hg vacuum

Equipment made on/after Nov 15, 1993, compressor is NOT functional Recover 80% of the refrigerant OR pull a 4-inch Hg vacuum

Equipment made before Nov 15, 1993 Recover 80% of the refrigerant OR pull a 4-inch Hg vacuum

The logic is intuitive: a working compressor helps push refrigerant out, so the EPA expects a higher capture rate. A dead compressor traps refrigerant in oil and is harder to evacuate, so the standard drops to 80%. The 4-inch Hg vacuum alternative applies to both cases — if you can pull the small appliance down to 4 inches of mercury vacuum, you have met the requirement no matter the compressor status.

Two Families of Recovery Equipment

Type I recognizes two equipment categories, and the exam expects you to tell them apart.

System-Dependent (Passive) Recovery

System-dependent recovery equipment "requires the assistance of components contained in an appliance to remove the refrigerant." It has no compressor of its own — it borrows the appliance's compressor or simply relies on a pressure differential. Two key limits:

It is prohibited on appliances containing more than 15 lbs of refrigerant. (Small appliances hold 5 lb or less, so passive equipment is always legal on them — but the 15-lb cap is a favorite exam trap.)

When the appliance compressor still runs, you must operate that compressor during recovery to move refrigerant toward the high side where the recovery device captures it.

Self-Contained (Active) Recovery

Self-contained recovery equipment has its own compressor and actively pulls refrigerant from the appliance. It works whether or not the appliance compressor is alive, and it is generally faster and more thorough. It is the only practical choice when the appliance compressor is burned out.

  • Feature System-dependent (passive) Self-contained (active)
  • Own compressor? No — borrows the appliance's Yes
  • Works with dead compressor? Slowly, via pressure differential Yes, fully
  • Charge-size limit ≤ 15 lbs None (rated to its design)
  • Speed/thoroughness Lower Higher
  • Accessing a Sealed System

Small appliances usually have no service valve, so you must create an access point. Three options:

Process tube — the crimped stub left from manufacturing; open it by piercing or cutting.

Line-tap (piercing/saddle) valve — clamps onto the line and pierces it to create a port.

Schrader valve — if one is present, it is a standard connection.

After recovery, any pierced opening must be sealed permanently (soldered, brazed, or capped). A line-tap valve is only a temporary access port and is not a permanent seal.

Freeing Refrigerant Trapped in Oil

When the compressor is dead and you are using passive recovery, refrigerant dissolves into the compressor oil (it is miscible with oil) and resists capture. EPA-recognized techniques to release it:

Apply heat to the compressor shell with a heating blanket or heat gun — never an open flame. Warm oil holds less dissolved refrigerant, so it boils off and can be recovered.

Sharply strike / tap the compressor with a rubber mallet to agitate the oil and shake refrigerant loose.

Allow extra time for refrigerant to migrate out, and run the recovery device in repeated short cycles to pull additional trapped charge.

Example: A dehumidifier with a seized compressor needs its R-410A recovered before disposal. You attach self-contained recovery gear through a line-tap valve and pull, but the gauge stalls before 80%. You wrap the compressor shell in a heating blanket and tap the base with a rubber mallet. The warmed oil releases its dissolved refrigerant, the recovery resumes, and you finish by pulling the unit to a 4-inch Hg vacuum — satisfying the requirement for a non-functional compressor.

Recovery Before Disposal

No small appliance may be discarded with refrigerant still inside. The refrigerant must be recovered first, and the last person in the disposal chain is responsible for ensuring it happened. A scrap dealer (the final processor) must either recover any remaining refrigerant itself — no technician certification is needed to recover refrigerant for disposal of a small appliance, though certified recovery equipment and the recovery levels still apply — or verify recovery with a signed statement (name and address of whoever recovered it, and the date) or a contract with a regular supplier, kept for three years.

Reading the Requirement Correctly on Exam Day

Many Type I questions pair a scenario with a number and ask you to pick the right recovery target. Train yourself to do three things in order: first decide whether the appliance is a small appliance at all, then ask whether the compressor is functional (and whether the recovery equipment was made on or after November 15, 1993) to set the 90% vs. 80% target, and finally remember that a 4-inch Hg vacuum satisfies either case.

Watch the distractors. A common one swaps in a 10-inch or 15-inch Hg vacuum — those belong to larger high- and medium-pressure (Type II) appliances, not Type I. Another pushes 100% recovery; the regulation never requires 100%. Keeping the three Type I numbers — 90%, 80%, and 4 inches Hg — separate from the larger-system numbers is what separates a pass from a near-miss on this section.

Finally, note that the equipment itself must be EPA-certified recovery equipment and properly maintained. Using uncertified gear, or venting any portion of the charge rather than recovering it, is a violation regardless of how small the appliance is — even a few ounces of refrigerant must be captured.

Loading diagram... Choosing a Type I Recovery Path