Study guide
9.3 Leak Detection, the Repair Triggers, and Recordkeeping
EPA 608 Technician Certification Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction to EPA 608 Certification
1.1 What EPA 608 Is and Who Needs It 1.2 Exam Format, Scoring, and Administration 1.3 How to Study for EPA 608
2 Regulations and the Clean Air Act
2.1 Clean Air Act Overview 2.2 Penalties and Enforcement 2.3 Montreal Protocol and International Agreements 2.4 AIM Act and HFC Phasedown Schedule 2.5 SNAP Program and Refrigerant Transitions
3 Refrigerants and Ozone Science
3.1 The Science of Ozone Depletion (ODP and GWP) 3.2 Refrigerant Classification, ASHRAE Numbering, and Safety Groups 3.3 Common Refrigerants: Properties, Applications, and Phaseout Status 3.4 Refrigerant Blends: Glide, Fractionation, and Liquid Charging
4 The Refrigeration Cycle
4.1 The Basic Refrigeration Cycle 4.2 System Components in Detail 4.3 Heat Transfer and Pressure-Temperature Relationships
5 Refrigerant Safety and Handling
5.1 Refrigerant Hazards and Health Effects 5.2 Safe Handling Practices, PPE, and Cylinders 5.3 A2L (Mildly Flammable) Refrigerant Safety
6 Recovery, Recycling, and Reclaiming
6.1 The Three Rs: Recover, Recycle, Reclaim 6.2 Recovery Equipment Requirements 6.3 Required Levels of Evacuation 6.4 Refrigerant Sales Restrictions and Recordkeeping
7 Leak Detection and Repair
7.1 Leak Detection Methods 7.2 Leak Repair Requirements and Trigger Rates 7.3 Leak-Rate Calculation, Recordkeeping, and Reporting
8 Type I — Small Appliances
8.1 What Counts as a Small Appliance 8.2 Type I Recovery Requirements 8.3 Type I Procedures, Access Valves, and the Open-Book Exam
9 Type II — High-Pressure Appliances
9.1 What Type II Covers: High-Pressure System Overview 9.2 Type II Recovery Methods and Required Evacuation Levels 9.3 Leak Detection, the Repair Triggers, and Recordkeeping 9.4 The R-22 Phaseout, Retrofits, and the Move to Lower-GWP A2Ls
10 Type III — Low-Pressure Appliances
10.1 Low-Pressure System Fundamentals 10.2 Purge Units and Air Management 10.3 Type III Recovery and Procedures 10.4 Type III Leak Testing
11 10. Disposal, Shipping, and Compliance
11.1 Equipment Disposal Requirements 11.2 Refrigerant Shipping and Transport 11.3 Compliance Checklist and Best Practices
12 Final Review and Exam Strategy
12.1 High-Yield Core Section Review 12.2 Type I vs Type II vs Type III: Side-by-Side Review 12.3 How the Exam Works and Exam-Day Strategy
9.3 Leak Detection, the Repair Triggers, and Recordkeeping
Key Takeaways Explain This Topic AI
Leak repair rules apply to appliances containing 50 lbs or more of ODS refrigerant; the 2024 ER&R rule (40 CFR 84.106) extends repair requirements from January 1, 2026 to 15 lbs or more of HFC/substitute refrigerant (residential and light commercial AC excluded)
Annual leak-rate triggers: comfort cooling 10%, commercial refrigeration 20%, industrial process refrigeration 30% — calculated over a 12-month period
When a trigger is exceeded, the owner must repair within 30 days (120 days if an industrial process shutdown is required) OR file a retrofit/retire plan within 30 days and complete it within 1 year
Repairs must pass an initial verification test (after repair, before recharge) and a follow-up verification test (after the system is back at normal operating conditions)
Electronic leak detectors locate the general area; soap-bubble solution pinpoints the exact leak; owners must keep records of refrigerant added and repairs made
Last updated: October 2026
Finding Leaks on High-Pressure Systems
Leak management is the heart of Type II compliance. High-pressure systems develop leaks at Schrader valve cores, flare and brazed joints, service-valve packing, and coil U-bends. Because refrigerant vapor is heavier than air , it tends to settle, so a methodical search starts at the lowest points of a suspected area and works upward.
A Reliable Leak-Detection Sequence
Confirm a leak exists. Review the appliance's service history and refrigerant-addition records, then calculate the annualized leak rate (see the formula below). A standing-pressure test with dry nitrogen can confirm a suspected loss.
Survey the general area. Use an electronic leak detector (heated-diode or infrared), moving the probe slowly — about 1 inch per second — along every joint and fitting. Electronic detectors are excellent at finding the general location of even small leaks.
Pinpoint the exact spot. Apply soap-bubble solution to the suspect joint; escaping refrigerant forms bubbles at the precise leak. Ultrasonic detectors and fluorescent UV dye are additional pinpointing tools.
Repair, then verify (covered below).
Calculating the Annualized Leak Rate
EPA allows the leak rate to be calculated by the annualizing method (shown here) or the rolling-average method:
Leak rate (%) = (pounds of refrigerant added ÷ full charge in pounds) × (365 ÷ days since refrigerant was last added) × 100
Worked Example: A commercial refrigeration system has a full charge of 100 lbs . A technician adds 8 lbs of refrigerant, and the previous top-off was 90 days ago. Annualized leak rate = (8 ÷ 100) × (365 ÷ 90) × 100 = 0.08 × 4.06 × 100 = 32.4% . Because this is commercial refrigeration , the trigger rate is 20% . 32.4% exceeds 20%, so the leak-repair clock starts: the owner must repair within 30 days or file a retrofit/retire plan.
The Leak-Repair Trigger Rates
The trigger rate is the annual leak rate above which an owner/operator must take action. It varies by how the appliance is used:
- Appliance Use Annual Trigger Rate Examples
- Comfort cooling (and other appliances) 10% Building AC, chillers used for occupant comfort, heat pumps
- Commercial refrigeration 20% Supermarket racks, walk-in coolers/freezers, food retail
- Industrial process refrigeration (IPR) 30% Refrigeration tied to a manufacturing/chemical process
- Which Appliances the Rules Cover
ODS refrigerants (CFC/HCFC such as R-22): leak-repair rules apply to appliances with a full charge of 50 lbs or more .
HFCs and HFC substitutes (40 CFR 84.106): beginning January 1, 2026 , the 2024 HFC Emissions Reduction and Reclamation rule (40 CFR Part 84, Subpart C) extends leak-repair requirements to appliances with a charge of 15 lbs or more of an HFC or covered substitute. Residential and light-commercial AC and heat pumps are exempt , and substitutes with a GWP of 53 or below are not covered.
For the Exam: Memorize 10 / 20 / 30 mapped to comfort cooling / commercial refrigeration / industrial process , the 50-lb ODS threshold, and Part 84's 15-lb HFC threshold (from January 1, 2026). A frequent trap reverses the 20% and 30% values — commercial refrigeration is 20%, industrial process is 30%.
After the Trigger Is Exceeded: The Compliance Clock
Once the calculated leak rate exceeds the trigger, the owner/operator has two paths:
Repair the leak within 30 days of the refrigerant addition that shows the trigger is exceeded (extended to 120 days when an industrial process shutdown is required to make the repair), or
Develop a retrofit or retirement plan within 30 days and complete the actions in that plan within 1 year of the plan date.
Verification Tests
A repair is not "done" until it passes two checks:
Initial verification test — performed after the repair but before the system is fully recharged , confirming the specific leak is sealed (for example, a standing nitrogen pressure test on the repaired section).
Follow-up verification test — performed after the system is back at normal operating temperature and pressure , confirming the repair holds under real operating conditions.
If either verification test fails, the leak is considered not repaired and the owner must continue repair efforts or move to a retrofit/retire plan.
Recordkeeping
Owners/operators of appliances subject to the leak-repair rules must keep records that include the date and amount of refrigerant added , the full charge of the appliance, the calculated leak rate , the date and result of verification tests , and leak inspection records. These records demonstrate compliance during an EPA audit and are the basis for the annualized leak-rate calculation. Technicians also document recovery, evacuation, and the refrigerant type used.