Study guide
10.1 Low-Pressure System Fundamentals
EPA 608 Technician Certification Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction to EPA 608 Certification
1.1 What EPA 608 Is and Who Needs It 1.2 Exam Format, Scoring, and Administration 1.3 How to Study for EPA 608
2 Regulations and the Clean Air Act
2.1 Clean Air Act Overview 2.2 Penalties and Enforcement 2.3 Montreal Protocol and International Agreements 2.4 AIM Act and HFC Phasedown Schedule 2.5 SNAP Program and Refrigerant Transitions
3 Refrigerants and Ozone Science
3.1 The Science of Ozone Depletion (ODP and GWP) 3.2 Refrigerant Classification, ASHRAE Numbering, and Safety Groups 3.3 Common Refrigerants: Properties, Applications, and Phaseout Status 3.4 Refrigerant Blends: Glide, Fractionation, and Liquid Charging
4 The Refrigeration Cycle
4.1 The Basic Refrigeration Cycle 4.2 System Components in Detail 4.3 Heat Transfer and Pressure-Temperature Relationships
5 Refrigerant Safety and Handling
5.1 Refrigerant Hazards and Health Effects 5.2 Safe Handling Practices, PPE, and Cylinders 5.3 A2L (Mildly Flammable) Refrigerant Safety
6 Recovery, Recycling, and Reclaiming
6.1 The Three Rs: Recover, Recycle, Reclaim 6.2 Recovery Equipment Requirements 6.3 Required Levels of Evacuation 6.4 Refrigerant Sales Restrictions and Recordkeeping
7 Leak Detection and Repair
7.1 Leak Detection Methods 7.2 Leak Repair Requirements and Trigger Rates 7.3 Leak-Rate Calculation, Recordkeeping, and Reporting
8 Type I — Small Appliances
8.1 What Counts as a Small Appliance 8.2 Type I Recovery Requirements 8.3 Type I Procedures, Access Valves, and the Open-Book Exam
9 Type II — High-Pressure Appliances
9.1 What Type II Covers: High-Pressure System Overview 9.2 Type II Recovery Methods and Required Evacuation Levels 9.3 Leak Detection, the Repair Triggers, and Recordkeeping 9.4 The R-22 Phaseout, Retrofits, and the Move to Lower-GWP A2Ls
10 Type III — Low-Pressure Appliances
10.1 Low-Pressure System Fundamentals 10.2 Purge Units and Air Management 10.3 Type III Recovery and Procedures 10.4 Type III Leak Testing
11 10. Disposal, Shipping, and Compliance
11.1 Equipment Disposal Requirements 11.2 Refrigerant Shipping and Transport 11.3 Compliance Checklist and Best Practices
12 Final Review and Exam Strategy
12.1 High-Yield Core Section Review 12.2 Type I vs Type II vs Type III: Side-by-Side Review 12.3 How the Exam Works and Exam-Day Strategy
10.1 Low-Pressure System Fundamentals
Key Takeaways Explain This Topic AI
EPA defines a low-pressure refrigerant by its liquid saturation pressure: below 45 psia at 104 °F; such refrigerants boil near or above room temperature (R-123 at 82°F, R-11 at 75°F, R-113 at 118°F)
Because they boil so high, the evaporator must run in a deep vacuum, so leaks pull air and moisture IN rather than letting refrigerant out
Type III equipment is almost always a large centrifugal chiller (100–10,000+ tons) serving hospitals, campuses, and high-rises
Air and moisture infiltration — not refrigerant escape — is the defining service concern of every low-pressure system
Pressures are read in inches of mercury (in. Hg) vacuum or mm Hg absolute, never on an ordinary high-side compound gauge
Last updated: October 2026
What "Low-Pressure" Really Means
Type III certification covers low-pressure appliances — in practice, the large centrifugal chillers that air-condition hospitals, universities, high-rise offices, data centers, and district-cooling plants. The EPA defines a low-pressure appliance as one that uses a refrigerant with a liquid-phase saturation pressure below 45 psia at 104 °F (40 CFR 82.152); EPA's examples are R-11, R-123, R-113, and R-245fa. In practice these refrigerants boil near or above room temperature at atmospheric pressure, and that drives everything else you must know for the exam.
When a refrigerant boils above room temperature, the only way to make it evaporate at the 35–40°F needed to chill water is to lower the pressure far below atmospheric — a deep vacuum. So the evaporator (the low side) of a Type III machine normally runs at 6–10 in. Hg of vacuum or deeper , and even the condenser can sit near or below atmospheric on a cool day. This is the mirror image of a Type II R-410A system, where every component sits well above atmospheric.
The Defining Consequence: Leaks Pull Air IN
Because the system is below atmospheric pressure, a leak does not let refrigerant escape — it lets air and moisture get sucked IN. This is the most heavily tested concept in all of Type III. Air (nitrogen and oxygen) and water vapor are non-condensable gases (NCGs) that collect in the machine, raise condenser pressure, waste energy, and — worst of all — introduce moisture that combines with refrigerant and heat to form acids and sludge. Every recovery rule, purge-unit design, and leak-test limit you will study exists to manage air and moisture infiltration.
Common Low-Pressure Refrigerants
These refrigerants all have saturation pressures below 45 psia at 104 °F — EPA's low-pressure test — and most boil near or above room temperature.
- Refrigerant Class Boiling Point @ atmospheric ODP GWP Status
- R-11 (CFC-11) CFC 74.9°F (23.8°C) 1.0 4,750 Production banned 1996; legacy chillers
- R-113 (CFC-113) CFC 117.6°F (47.6°C) 0.8 6,130 Older centrifugal/industrial; phased out
- R-123 (HCFC-123) HCFC 82.2°F (27.9°C) 0.02 77 Servicing only; production phase-out by 2030
- R-245fa HFC 59.5°F (15.3°C) 0 1,030 Some ORC/chiller use; AIM Act phasedown
- R-1233zd(E) HFO 64.4°F (18.0°C) 0 ~1 Modern low-GWP centrifugal replacement
Example: A campus plant runs three 1,200-ton centrifugal chillers charged with R-123 (boils at 82°F). On a 70°F mechanical-room day, a technician opens an access port for a quick gauge check and hears a hiss — but it is air rushing IN, not refrigerant blowing out. Because R-123 boils at 82°F, the evaporator is sitting in a vacuum, so the surrounding 14.7 psia atmosphere pushes air through any opening. The fix is not "top off the charge" — it is find and seal the leak, then let the purge unit clear the air.
Why a Standard Gauge Won't Work
An ordinary compound gauge is built to read pressure, not deep vacuum. Type III work uses a micron (absolute) gauge or an electronic vacuum gauge that reads in mm Hg absolute or microns. Knowing the unit is essential, because the recovery target (25 mm Hg absolute) is meaningless on a psig scale.
Centrifugal Chiller Construction
Type III machines look nothing like the condensing units of Type II. Know these components and their function:
Centrifugal compressor — a high-speed impeller flings vapor outward, converting velocity to pressure. It moves huge vapor volumes at a small pressure rise, which is exactly what a low-pressure refrigerant needs.
Shell-and-tube evaporator (cooler) — refrigerant boils in the shell around bundles of water tubes; chilled water leaves to the building.
Shell-and-tube condenser — hot vapor condenses on tubes carrying cooling-tower (condenser) water.
Purge unit — continuously removes air/NCGs that leak into the vacuum (covered in 9.2).
Rupture disc — a one-time safety device rated at the chiller's maximum working pressure that bursts to relieve overpressure (Trane, for example, rates the disc on its R-123 CenTraVac chillers at 15 psig ±2 psig ).
Oil sump + heater — lubricates bearings; the heater stays energized during shutdown to stop refrigerant migration.
The Vacuum-Operation Recap
Everything about Type III flows from one fact: low-pressure refrigerants boil high, so the machine runs in a vacuum, so leaks admit air and moisture. Hold that chain of logic and most exam questions answer themselves.
For the Exam: A low-pressure appliance uses a refrigerant with a liquid saturation pressure BELOW 45 psia at 104 °F (R-123, R-11, R-113 — which boil at about 82°F, 75°F, and 118°F). The evaporator runs in a vacuum, so leaks pull AIR and MOISTURE in. The compressor is centrifugal (an impeller). Air infiltration — not refrigerant loss — is the primary concern.