Study guide

3.1 ASTM E1728 Dust Wipe Sampling Protocols, Materials, Spikes, and Field Blanks

EPA Lead Risk Assessor 40 CFR 745 Subpart L

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Regulatory Framework & Statutory Authority

1.1 TSCA Title IV, Title X, and EPA Regulatory Authority 1.2 40 CFR 745 Subpart L: Scope, Target Housing, and Child-Occupied Facilities 1.3 Lead Certification Roles: Inspector vs. Risk Assessor vs. Abatement Supervisor 1.4 HUD Lead Safe Housing Rule (24 CFR Part 35) & TSCA Section 1018 Disclosure

2 Chapter 2: Hazard Identification & Visual Assessment

2.1 Visual Inspection Protocols and Paint Condition Rating (Intact, Fair, Deteriorated) 2.2 Evaluating Friction, Impact, and Chewable Surface Hazards 2.3 XRF Analyzer Operating Principles, Performance Characteristic Sheets (PCS), and Inconclusive Ranges 2.4 Paint Chip Sampling Protocol, Laboratory Submissions, and Paint Presumptions 2.5 Background Information Collection for Risk Assessments 2.6 Lead Hazard Screen Protocol (40 CFR 745.227(c))

3 Chapter 3: Dust and Soil Sampling Protocols

3.1 ASTM E1728 Dust Wipe Sampling Protocols, Materials, Spikes, and Field Blanks 3.2 EPA Dust-Lead Hazard Standards (40 CFR 745.65) & Post-Abatement Action Levels 3.3 ASTM E1727 Soil Sampling Protocols, Composite Sub-sampling, and Core Depths 3.4 Soil-Lead Hazard Thresholds (Play Areas vs. Bare Soil) and Action Triggers 3.5 Other Environmental Lead Sources: Water, Air, Packaging, and Food

4 Chapter 4: Laboratory Quality Control & Chain of Custody

4.1 NLLAP Laboratory Accreditation & Approved Analytical Methods (AAS, ICP-AES) 4.2 Field Quality Control: Blank Preparation, Field Duplicates, and Acceptance Criteria 4.3 Chain of Custody (COC) Documentation, Sample Handling, and Shipping Regulations 4.4 Interpreting Laboratory Data, Reconciling QC Failures, and Data Validation

5 Chapter 5: Lead Hazard Control Recommendations

5.1 Regulatory Definitions: Interim Controls vs. Abatement Strategies 5.2 Paint Hazard Control Options: Encapsulation, Enclosure, and Surface Modifications 5.3 Dust and Soil Hazard Controls: Specialized Cleaning, Cover Options, and Removal 5.4 Re-evaluation Intervals, Maintenance Schedules, and Monitoring Plans

6 Chapter 6: Risk Assessment Report & Compliance

6.1 Mandatory Report Components under 40 CFR 745.227(d)(11) and HUD Chapter 5 6.2 Hazard Prioritization, Risk Reduction Action Plans, and Client Communication 6.3 Recordkeeping Regulations, Document Retention (3-Year Rule), and Audit Readiness 6.4 State-Authorized Lead Programs, Local Variations, and Reciprocity Rules

3.1 ASTM E1728 Dust Wipe Sampling Protocols, Materials, Spikes, and Field Blanks

Key Takeaways Explain This Topic AI

ASTM E1728 governs the standard practice for field collection of settled dust samples using wipe sampling methods for subsequent lead determination.

Wipes must comply with ASTM E1792 standards, measuring approximately 10x10 cm, pre-moistened with deionized water, and containing background lead levels below 5 µg per wipe.

The wipe sampling technique requires two 90-degree S-pattern passes (first side-to-side, then top-to-bottom) with the wipe folded clean-side-in between passes.

Quality control requires field blanks at a rate of 1 per 20 field samples (or 1 per site per day, minimum 1 per batch) and blind field spikes with 80% to 120% acceptable laboratory recovery.

Lead loading is calculated using the formula: Lead Loading (µg/ft²) = Total Lead (µg) / Area Sampled (ft²), where area in ft² equals Area (sq in) / 144.

Last updated: July 2026

3.1 ASTM E1728 Dust Wipe Sampling Protocols, Materials, Spikes, and Field Blanks

Dust wipe sampling is the primary quantitative method used by EPA-certified Lead Risk Assessors and Clearance Technicians to measure surface lead loading in residential target housing and child-occupied facilities. The standard operational framework for collecting settled dust samples is established under ASTM E1728 ( Standard Practice for Collection of Settled Dust Samples Using Wipe Sampling Methods for Subsequent Lead Determination ). Compliance with ASTM E1728 ensures that dust wipe samples are collected reproducibly, without cross-contamination, and in a format suitable for National Lead Laboratory Accreditation Program (NLLAP) accredited analytical laboratories.

1. Wipe Material Specifications & ASTM E1792 Standard

Not all commercial wipes or wet-wipes are suitable for environmental lead sampling. ASTM E1728 mandates that field wipes must meet the strict material requirements set forth in ASTM E1792 ( Standard Specification for Wipe Sampling Materials for Lead in Surface Dust ).

Key Material Requirements

Background Lead Content: The wipe material must contain background lead concentrations of less than 5 µg Pb per wipe (ideally below the laboratory method detection limit).

Moisture & Solution: Wipes must be pre-moistened with deionized water or a weak aqueous alcohol solution. Wipes containing aloe, lanolin, perfumes, oils, or heavy surfactant lotions (such as standard baby wipes) are strictly prohibited because organic additives interfere with laboratory acid digestion and flame atomic absorption spectrometry (FAAS) or inductively coupled plasma mass spectrometry (ICP-MS) analytical instruments.

Physical Integrity & Durability: The wipe must be sufficiently durable so that it does not tear, shred, or leave fibrous residue on rough surfaces (such as textured wood or masonry) during sampling.

Size & Dimensions: Standard sampling wipes are approximately 10 cm x 10 cm (roughly 4 inches x 4 inches).

Digestibility: The wipe matrix must dissolve or yield complete lead extraction when subjected to hot nitric acid/hydrogen peroxide digestion under ASTM E1741 or EPA Method 3050B.

  • Specification Parameter Requirement / Standard
  • Standard Practice Specification ASTM E1728
  • Material Specification Standard ASTM E1792
  • Maximum Allowed Background Lead < 5 µg Pb per wipe
  • Wetting Agent Deionized water or alcohol-water solution (No aloe, lanolin, or oils)
  • Matrix Compatibility Nitric acid hot-block digestion compliant
  • Sample Container Type Rigid, clean, non-leaching polypropylene centrifuge tubes (50 mL)
  • 2. Template Selection, Dimensions, and Decontamination

To calculate dust lead loading accurately in micrograms per square foot (µg/ft²), the surface area sampled must be precisely measured and recorded.

Template Types & Dimensions

Rigid Reusable Templates: Typically constructed of smooth, non-porous plastic or metal (e.g., acrylic or aluminum) with an internal opening of 12 inches x 12 inches (1.0 ft²) or 100 cm² . Reusable templates MUST be thoroughly decontaminated between every sample using a fresh ASTM E1792 wipe pre-moistened with deionized water to prevent cross-contamination.

Disposable Single-Use Templates: Single-use paper or plastic sticky-back templates (1 ft² opening) eliminate the need for field decontamination between samples and are preferred in high-throughput field risk assessments.

Custom / Trough Measurements: For narrow surfaces where a standard 12 in x 12 in square template does not fit—such as window sills (stools) or window troughs (wells)—the assessor must measure the exact sampled area using a disposable ruler or calibrated tape measure to the nearest 1/16 inch (0.1 cm) . The length and width are multiplied to calculate total square inches, which is then converted to square feet.

3. Step-by-Step Dust Wipe Sampling Technique (S-Pattern Execution)

ASTM E1728 specifies a rigorous, standardized multi-pass wiping protocol to capture all settled dust within the target area. Pass 1: Side-to-Side S-Pattern Pass 2: Top-to-Bottom S-Pattern (90° Turn)

  • ┌─────────────────────────────┐ ┌─────────────────────────────┐
  • │ ══════════════════════════> │ │ ║ ║ ║ ║ ║ ║ ║ ║ ║ ║ │
  • │ <══════════════════════════ │ │ ║ ║ ║ ║ ║ ║ ║ ║ ║ ║ │
  • │ ══════════════════════════> │ │ ║ ║ ║ ║ ║ ║ ║ ║ ║ ║ │
  • │ <══════════════════════════ │ │ ║ ║ ║ ║ ║ ║ ║ ║ ║ ║ │
  • └─────────────────────────────┘ └─────────────────────────────┘
  • (Fold wipe clean side IN) (Fold clean side IN, wipe perimeters)
  • Field Sampling Workflow

Personal Protective Equipment (PPE): Put on a clean pair of powder-free disposable nitrile gloves prior to handling the sampling wipe or template. Gloves MUST be changed between every individual sample location to prevent cross-contamination.

Template Placement: Securely place or adhere the template over the target surface (e.g., bare floor, carpet, window sill, window trough).

First Pass (Side-to-Side S-Pattern): Open the pre-moistened wipe completely, place it flat on the surface inside the top left corner of the template. Wipe the surface from side to side in an overlapping "S" or serpentine pattern, progressing downward from the top edge to the bottom edge. Ensure the wipe touches the interior edges of the template.

First Fold: Fold the wipe in half, keeping the dirty side folded inward (clean side out).

Second Pass (Top-to-Bottom S-Pattern): Turn the wiping direction 90 degrees . Wipe the entire template area from top to bottom in an overlapping serpentine pattern, moving from left to right across the surface.

Second Fold & Perimeter Wipe: Fold the wipe in half again with the collected dust turned inside. Carefully wipe the inner perimeter edges of the template to capture any remaining loose dust particles.

Containerization: Insert the folded wipe directly into a clean, labeled, rigid 50 mL polypropylene centrifuge tube. Do NOT use plastic zip-lock bags or paper envelopes, as dust particles adhere electrostatically to bag walls or leach into paper fibers, causing sample loss during laboratory transfer.

Documentation: Record the unique sample identification number, exact location, surface component type, and exact dimensions (width and length in inches, or total ft²) on both the centrifuge tube label and the Field Sampling Form / Chain of Custody (COC).

4. Quality Control Protocols: Field Blanks and Blind Field Spikes

Quality assurance and quality control (QA/QC) samples are mandatory under EPA regulations and NLLAP standards to verify field precision, detect cross-contamination, and monitor laboratory analytical accuracy.

Field Blanks

Definition: A field blank is an unused ASTM E1792 wipe taken from the same lot as the sampling wipes. The assessor opens the wipe packet at the sampling site, folds it using clean nitrile gloves, and places it directly into a sample centrifuge tube without touching any environmental surface.

Required Frequency: Exactly 1 field blank per 20 field samples collected, OR 1 field blank per sampling site per day , whichever is more frequent (with a strict minimum of 1 field blank per sampling batch).

Purpose: Detects contamination introduced by wipes, sample containers, glove handling, or airborne field conditions. If a field blank returns a lead level above 5 µg/wipe (or above the laboratory reporting limit), all field sample results from that batch are invalidated and must be re-sampled.

Blind Field Spikes (Spiked Samples)

Definition: Field spikes are wipes pre-spiked by an independent laboratory with a known quantity of lead (typically 50 µg to 200 µg Pb). They are submitted to the analytical laboratory "blind" (labeled like routine field samples so the lab analysts cannot distinguish them).

Acceptable Laboratory Recovery: The laboratory analytical recovery rate must fall within 80% to 120% of the target spiked value.

Purpose: Verifies laboratory digestion efficiency and instrument calibration accuracy for wipe matrices.

  • QC Sample Type Target / Spike Value Minimum Frequency Acceptable Control Limit
  • Field Blank Unused wipe (0 µg Pb) 1 per 20 samples (or 1 per site/day) < 5 µg Pb per wipe (or < RL)
  • Blind Field Spike 50 µg - 200 µg Pb As required by QA program (e.g., 1 per batch) 80% to 120% recovery
  • 5. Dust Lead Loading Calculations and Area Conversions

Analytical laboratories report wipe sample results as total lead mass in micrograms (µg Pb). The risk assessor must calculate surface lead loading in micrograms per square foot (µg/ft²).

  • Primary Formula
  • Lead Loading (µg/ft²) = Total Lead Reported by Lab (µg) / Sampled Area (ft²)
  • Area Conversion Formula

When dimensions are measured in inches (Length in inches x Width in inches): Area in ft² = (Length in inches x Width in inches) / 144

Combining these formulas yields: Lead Loading (µg/ft²) = Total Lead (µg) / [ (Length in in x Width in in) / 144 ]

Worked Example 1: Standard 12" x 12" Template

Laboratory Result: 8.5 µg Pb reported.

Sampled Area: 12 inches x 12 inches = 144 sq in = 1.0 ft².

  • Lead Loading Calculation: Lead Loading = 8.5 µg / 1.0 ft² = 8.5 µg/ft²
  • Worked Example 2: Window Sill (6" x 24")

Laboratory Result: 25.0 µg Pb reported.

Dimensions: Width = 6 inches, Length = 24 inches.

Area Calculation: Area = (6 x 24) / 144 = 144 / 144 = 1.0 ft² .

  • Lead Loading Calculation: Lead Loading = 25.0 µg / 1.0 ft² = 25.0 µg/ft²
  • Worked Example 3: Narrow Window Sill (4" x 18")

Laboratory Result: 15.0 µg Pb reported.

Dimensions: Width = 4 inches, Length = 18 inches.

Area Calculation: Area = (4 x 18) / 144 = 72 / 144 = 0.5 ft² .

  • Lead Loading Calculation: Lead Loading = 15.0 µg / 0.5 ft² = 30.0 µg/ft²
  • 6. Common Field Errors & Cross-Contamination Prevention

Maintaining strict protocol integrity prevents common field sampling errors that lead to false positives, false negatives, or legal invalidation of lead hazard assessments:

Failure to Change Gloves: Reusing gloves across multiple sample locations transfers dust from high-lead surfaces (e.g., window troughs) to clean surfaces (e.g., floors), skewing results.

Using Non-Compliant Wipes: Utilizing commercial baby wipes containing lotions or aloe leads to digestion failures in the lab and unreliable lead readings.

Improper Container Choice: Storing wipes in flexible plastic baggies causes dust loss due to static electricity sticking to the interior bag walls.

Incorrect Area Measurement: Estimating or failing to measure window sill dimensions accurately causes severe errors in calculated µg/ft² lead loading values.

Reusing Templates Without Decontamination: Failing to wipe reusable acrylic or metal templates between samples leads to carryover contamination.