Study guide
9.3 Work Plans, Method Selection Documentation, and Pre-Abatement Walkthrough
EPA Lead Abatement Supervisor 40 CFR 745 Subpart L
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Facts, Supervisor Role, and Certification Path
1.1 Current Exam Facts 1.2 Supervisor Role, Responsibilities, and On-Site Presence 1.3 Prerequisites, Interim Certification, and the Third-Party Exam
2 Chapter 2: Firm Certification, Recertification, and Enforcement
2.1 Firm Certification vs Individual Certification 2.2 Recertification, 8-Hour Refresher, and 3-Year vs 5-Year Cycles 2.3 Suspension, Revocation, TSCA Violations, and Inspections
3 Chapter 3: Title X, 40 CFR 745, State Programs, and HUD Guidelines
3.1 Title X, TSCA 402–406, and 40 CFR 745 Architecture 3.2 Target Housing, Child-Occupied Facilities, and the 1978 Ban 3.3 EPA-Administered vs Authorized State Programs (Subpart Q) and Reciprocity 3.4 HUD Guidelines and Other Documented Methodologies
4 Chapter 4: Lead Health Effects, Blood-Lead Benchmarks, and Liability
4.1 Lead Toxicology, Child and Adult Health Effects, and Blood-Lead Benchmarks 4.2 Liability, Insurance, and Contract Risk for Abatement Supervisors
5 Chapter 5: What Counts as Abatement
5.1 Abatement vs Interim Controls vs RRP 5.2 Lead-Based Paint Definition and Component Language 5.3 Paint-Lead, Dust-Lead, and Soil-Lead Hazard Definitions
6 Chapter 6: Lead Hazard Recognition in the Field
6.1 Deteriorated Paint and Paint in Poor Condition 6.2 Friction, Impact, and Chewable Surface Hazards 6.3 High-Risk Components, Common Areas, and Dust Pathways
7 Chapter 7: Interpreting Inspection and Risk Assessment Reports
7.1 Reading Inspection Reports, XRF Results, and Paint-Chip Data 7.2 Reading Risk Assessment Reports and Selecting Control Options 7.3 Lead Hazard Screens vs Full Risk Assessments
8 Chapter 8: Occupant Protection Plans
8.1 Occupant Protection Plan Requirements 8.2 Relocation, Isolation of Work Areas, and Sensitive Occupants 8.3 Re-Occupancy Criteria, Occupant Notice, and Access Control
9 Chapter 9: Project Notification and Work Plans
9.1 Five-Business-Day Notification Contents and Electronic Filing 9.2 Updated, Canceled, EBL, and Emergency Notifications 9.3 Work Plans, Method Selection Documentation, and Pre-Abatement Walkthrough
10 Chapter 10: Interior Containment Design
10.1 Critical Barriers, Warning Signs, and Regulated Areas 10.2 Negative Air Pressure and HEPA Air-Filtration Units 10.3 Three-Stage Decontamination Units and Worker Flow
11 Chapter 11: Exterior Containment and Site Control
11.1 Exterior Ground Sheeting, Vertical Containment, and Weather Limits 11.2 Daily Exterior Cleanup, Paint-Chip Control, and Occupied/Multi-Family Logistics
12 Chapter 12: Component Replacement, Enclosure, and Encapsulation
12.1 Component Replacement 12.2 Enclosure Systems and Mechanical Fastening 12.3 Encapsulation Products, Unsuitable Surfaces, and Maintenance Schedules
13 Chapter 13: Paint Removal and Restricted Practices
13.1 Wet Scraping, Chemical Removal, and Heat Guns Below 1100°F 13.2 Restricted and Prohibited Practices 13.3 Selecting Methods, Combining Methods, and Documenting Why
14 Chapter 14: Interior Dust Abatement and Cleaning
14.1 Interior Dust Cleanup Sequence 14.2 Pre-Clearance Visual Inspection and When Cleanup Is Not Done
15 Chapter 15: Soil and Exterior Dust Abatement
15.1 Soil-Lead Hazards and Sampling Interpretation for Supervisors 15.2 Soil Removal and Replacement 15.3 Permanent Covering vs Landscaping
16 Chapter 16: OSHA 1926.62 Worker Protection
16.1 PEL, Action Level, and Exposure Assessment 16.2 Respiratory Protection, PPE, and Hygiene Facilities 16.3 Biological Monitoring and Medical Removal Protection 16.4 OSHA Competent Person Duties vs EPA Certified Supervisor Duties
17 Chapter 17: RCRA Waste Management
17.1 Abatement Waste Streams 17.2 TCLP Characterization and D008 17.3 Manifests, TSDF, Accumulation, and the Household Exclusion
18 Chapter 18: Action Levels, Post-Abatement Testing, and Records
18.1 Dust-Lead Action Levels vs Reportable-Level Hazards 18.2 Post-Abatement Visual, Dust Sampling, Independence, and the 1-Hour Wait 18.3 Failed Samples, Reclean/Retest, Exterior Visual, and Multi-Family Random Sampling 18.4 Abatement Report, 2026 Hazard Statement, Owner Copies, and 3-Year Retention
9.3 Work Plans, Method Selection Documentation, and Pre-Abatement Walkthrough
Key Takeaways Explain This Topic AI
745.227 does not number a separate work-plan form. The later abatement report must include a detailed written description of the abatement: methods used, locations of rooms and/or components, the reason for selecting particular abatement methods for each component, and any suggested monitoring of encapsulants or enclosures (745.227(e)(10)(vi)).
Convert the inspection or risk-assessment report into a component-by-component method matrix with those reasons before the first strip of containment; do not invent reasons at clearance week.
Restricted practices in 745.227(e)(6) must be planned out of the job (no open-flame torching; machine sanding/grinding/blasting only with HEPA exhaust; dry-scrape limits; heat guns below 1100°F). Chapter 13 teaches the how; this chapter refuses illegal methods in the bid.
The certified supervisor shall be onsite during all work-site preparation (745.227(e)(2)). The pre-abatement walkthrough confirms components against the report, occupant status against the OPP, utilities, access, and the waste path.
Write methods first, then the unique occupant protection plan (Chapter 8) and containment (Chapter 10) around those methods. If the walkthrough changes quantity or location, apply Section 9.2's update clocks.
Last updated: August 2026
Method-by-component plans, reasons on paper, and the pre-abatement walkthrough
Quick Answer: 40 CFR 745.227 does not number a separate "work plan" form. The abatement report you will sign later must include a detailed written description of the abatement: methods , locations of rooms and/or components , the reason for selecting particular abatement methods for each component , and any suggested monitoring of encapsulants or enclosures ( 745.227(e)(10)(vi) ). Supervisors who wait until the report to invent those reasons fail the job and the exam. Turn the inspection / risk-assessment report into a component-by-component method list before the first strip of containment, plan restricted practices out of the work ( 745.227(e)(6) ; Chapter 13), and walk the site as the supervisor who must be on-site during all work-site preparation ( 745.227(e)(2) ).
This section is the bridge from Chapter 7 (reading the reports) and Chapter 8 (occupant protection) into Chapter 10 (containment). Notification told EPA when and where . The work plan — whatever you title the internal document — tells the crew what will be done to which component and why .
There is no 745.227 "Form W," but the report will demand the plan
745.227(e)(10) says an abatement report shall be prepared by a certified supervisor or project designer . Among the required contents, (e)(10)(vi) is the method paragraph:
"A detailed written description of the abatement, including abatement methods used, locations of rooms and/or components where abatement occurred, reason for selecting particular abatement methods for each component, and any suggested monitoring of encapsulants or enclosures."
Read the nouns. Methods (not "we abated the house"). Locations of rooms and/or components (not "interior"). Reason for selecting particular abatement methods for each component (not a single blanket "because the owner said so"). Suggested monitoring if you enclosed or encapsulated.
If those sentences do not exist until Friday afternoon of clearance week, they will be fiction. The professional practice is to write them before mobilization, using the inspection and risk-assessment reports Chapter 7 taught you to read. Call that document a work plan, a scope-of-work attachment, a method matrix, or a job hazard analysis — EPA does not give it a section number. The report is what 745.227 numbers. The plan is how a supervisor makes the report true.
The occupant protection plan is separate and is numbered: 745.227(e)(5) requires a written OPP, unique to each residential dwelling or child-occupied facility, developed prior to the abatement, by a certified supervisor or project designer . Chapter 8 owns OPP uniqueness, relocation, isolation, and re-occupancy. This chapter owns the method choices the OPP has to protect people from.
Turn the risk-assessment report into a component matrix
A risk-assessment report ( 745.227(d)(11) ) already lists hazards and "a description of interim controls and/or abatement options for each identified lead-based paint hazard" plus a suggested prioritization, and if encapsulant or enclosure is recommended, a maintenance and monitoring schedule . An inspection report lists which components are LBP. Neither report is a work order. The supervisor (or project designer) converts options into the method for this contract.
Build a table before the walkthrough, then correct it on site:
Component / room Hazard in the RA/inspection Method selected Why this method (what you will later put in (e)(10)(vi)) Restricted-practice check Monitoring after?
Living-room lower sash, friction Paint-lead on friction surface; dust on sill Component replacement of the window assembly Friction will grind any remaining film; replacement permanently removes the painted slide No dry sanding of the old sash on site; score, wet, remove whole No encapsulant; none
Stair-riser, impact, deteriorated Impact-surface paint-lead hazard Component replacement of risers Repeated shoe impact would fail an encapsulant or thin enclosure Heat gun, if any, below 1100°F ; no torching No
Intact living-room wall, no chew marks LBP present, not a current paint-lead hazard, but in the abatement scope Enclosure with mechanically fastened rigid material, or encapsulation if the substrate passes Intact, low-abuse surface; enclosure/encapsulant can be a permanent barrier if monitored No machine grinding without HEPA exhaust Yes — suggested monitoring schedule
Play-area bare soil 1,800 ppm Soil-lead hazard (≥ 400 ppm play area) Remove and replace with soil as close to local background as practicable, ≤ 400 ppm ; do not reuse as residential topsoil Concentration is a play-area hazard; grass/mulch is not permanent covering Waste path planned so excavated soil does not re-enter the yard No, if soil is gone; yes if you instead permanently cover with pavement/concrete
Kitchen floor dust Dust-lead hazard (any reportable level on or after Jan. 12, 2026) Interior dust abatement / specialized cleaning to below action levels (5 / 40 / 100) after other methods Dust is the remaining reservoir after paint work HEPA / wet sequence (Chapter 14); no dry sweeping No encapsulant
Reasons must be particular. "Replacement because it is abatement" is not a reason. Friction surfaces fail film-forming products because abrasion recreates dust. Chewable sills fail encapsulants that a toddler can mouth through. Deteriorated plaster may not hold an encapsulant. Historic-window owners may still choose replacement of stops and parting beads rather than the whole frame — that is a component-level reason, and it still has to be written for each component . Soil gets remove-and-replace or permanent cover (pavement/concrete), not landscaping dressed up as abatement (Chapter 15).
Plan restricted practices out of the job
745.227(e)(6) is not a cleanup rule. It is a method rule, so it belongs in the plan:
Open-flame burning or torching of LBP is prohibited . Do not put a torch on the method matrix "for paint that will not scrape."
Machine sanding, grinding, abrasive blasting, or sandblasting is prohibited unless used with HEPA exhaust control that removes particles of 0.3 microns or larger at 99.97% or greater efficiency.
Dry scraping is permitted only with heat guns, around electrical outlets, or when treating defective paint spots totaling no more than 2 ft² in any one room, hallway, or stairwell, or no more than 20 ft² on exterior surfaces.
Heat guns only below 1100°F .
Chapter 13 teaches the how. Chapter 9's job is to refuse a bid that assumes torching, open blasting, or whole-room dry scraping. If the only way the crew knows to get paint off a masonry lintel is a torch, that component's method is wrong before notification is even filed. Put the legal method on the matrix (wet scrape, chemical, heat gun below 1100°F, replacement) and make sure the brief description on the EPA notice in 9.1 matches that matrix. A notice that says "wet scrape and replace windows" while the truck is loaded with abrasive pots is a documentation problem waiting for an inspector.
Pre-abatement walkthrough — supervisor's body on site
745.227(e)(2) requires a certified supervisor for each abatement project and requires that supervisor to be onsite during all work-site preparation . The walkthrough is the last chance to make the plan true before preparation starts, and the first hours of preparation are not a telephone job.
Walk with the RA/inspection in one hand and the method matrix and draft OPP in the other. Punch at least this list:
Check What you are confirming If it fails
Components vs report The sash, radiators, soil patches, and stair parts on the report still exist, still match the XRF/chip IDs, and were not replaced since the inspection Stop and get the inspector/risk assessor, or treat untested look-alikes under the inspection rule for similar painting history — do not invent XRF numbers
Occupant status vs OPP Who is in the building, who is relocating, who is isolated, pregnant occupants, children under 6, pets, and the re-entry ban during work (Chapter 8) Rewrite the unique OPP before prep; a copied OPP with yesterday's address fails uniqueness
Utilities Water for wet methods and decon, power for HEPA vacuums and AFUs, HVAC shutdown points so you do not blow dust through the rest of the dwelling You cannot start wet scrape or negative air on a dead panel you never looked at
Access Crew entry, occupant exclusion, inspector's later path, elevator/stair use in multi-family Containment in Chapter 10 has to match this path
Waste path How bagged debris, filters, wastewater, and soil leave the regulated area without tracking through occupied rooms or over play-area soil RCRA characterization is Chapter 17; the route is a walkthrough item now
Exterior / weather Ground sheeting layout, wind, and whether the noticed acreage still matches (Chapter 11) A bigger facade than noticed can become a more than 20% update under 9.2
Clearance logistics Who the certified inspector or risk assessor will be, and that the supervisor will not self-clear Schedule independence now , not after final wet wash
Worked example — report says three windows, field has five. The RA listed living-room windows A, B, and C as friction hazards. The walkthrough finds two additional original sash in the same room that were never XRF'd because a bookcase hid them. You do not assume they are lead-free. You also do not silently add them to the 1,000 ft² notice if the extra work pushes quantity more than 20% . Get testing or treat them as LBP under the inspection "similar painting history" rule as appropriate, revise the method matrix , check the notice quantity, and revise the OPP if isolation zones change. That is the walkthrough earning its keep.
Worked example — OPP says vacant, crib in the corner. The unique OPP assumed relocation. A toddler's crib is still in the adjacent room with a blanket over the doorway. Preparation cannot start on the strength of a PDF. Occupant protection is prior to abatement ( 745.227(e)(5) ). Fix occupancy, then build containment (Chapter 10). The supervisor who is required on site for prep is the person who has to see the crib.
How this feeds Chapters 8 and 10
Write methods first, then write the OPP around those methods: replacement of windows produces whole-unit debris and a different isolation plan than spot encapsulation of a closet. Then design containment (critical barriers, negative air, decon — Chapter 10) to match both. Notification (9.1–9.2) already told EPA the address, dates, supervisor, and a brief description. The walkthrough is where that brief description either survives contact with the building or gets an updated notice the same day you still legally can.
Keep the paper pack together: inspection/RA, method matrix with reasons, unique OPP, received EPA (or State) notice, firm and supervisor certificates. That pack is what 745.227(e)(10) will turn into the abatement report, including the method-and-reason paragraph you already wrote.
Official sources: 40 CFR 745.227(e)(2), (e)(5), (e)(6), (e)(10)(vi) .