Study guide

15.2 Soil Removal and Replacement

EPA Lead Abatement Supervisor 40 CFR 745 Subpart L

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Facts, Supervisor Role, and Certification Path

1.1 Current Exam Facts 1.2 Supervisor Role, Responsibilities, and On-Site Presence 1.3 Prerequisites, Interim Certification, and the Third-Party Exam

2 Chapter 2: Firm Certification, Recertification, and Enforcement

2.1 Firm Certification vs Individual Certification 2.2 Recertification, 8-Hour Refresher, and 3-Year vs 5-Year Cycles 2.3 Suspension, Revocation, TSCA Violations, and Inspections

3 Chapter 3: Title X, 40 CFR 745, State Programs, and HUD Guidelines

3.1 Title X, TSCA 402–406, and 40 CFR 745 Architecture 3.2 Target Housing, Child-Occupied Facilities, and the 1978 Ban 3.3 EPA-Administered vs Authorized State Programs (Subpart Q) and Reciprocity 3.4 HUD Guidelines and Other Documented Methodologies

4 Chapter 4: Lead Health Effects, Blood-Lead Benchmarks, and Liability

4.1 Lead Toxicology, Child and Adult Health Effects, and Blood-Lead Benchmarks 4.2 Liability, Insurance, and Contract Risk for Abatement Supervisors

5 Chapter 5: What Counts as Abatement

5.1 Abatement vs Interim Controls vs RRP 5.2 Lead-Based Paint Definition and Component Language 5.3 Paint-Lead, Dust-Lead, and Soil-Lead Hazard Definitions

6 Chapter 6: Lead Hazard Recognition in the Field

6.1 Deteriorated Paint and Paint in Poor Condition 6.2 Friction, Impact, and Chewable Surface Hazards 6.3 High-Risk Components, Common Areas, and Dust Pathways

7 Chapter 7: Interpreting Inspection and Risk Assessment Reports

7.1 Reading Inspection Reports, XRF Results, and Paint-Chip Data 7.2 Reading Risk Assessment Reports and Selecting Control Options 7.3 Lead Hazard Screens vs Full Risk Assessments

8 Chapter 8: Occupant Protection Plans

8.1 Occupant Protection Plan Requirements 8.2 Relocation, Isolation of Work Areas, and Sensitive Occupants 8.3 Re-Occupancy Criteria, Occupant Notice, and Access Control

9 Chapter 9: Project Notification and Work Plans

9.1 Five-Business-Day Notification Contents and Electronic Filing 9.2 Updated, Canceled, EBL, and Emergency Notifications 9.3 Work Plans, Method Selection Documentation, and Pre-Abatement Walkthrough

10 Chapter 10: Interior Containment Design

10.1 Critical Barriers, Warning Signs, and Regulated Areas 10.2 Negative Air Pressure and HEPA Air-Filtration Units 10.3 Three-Stage Decontamination Units and Worker Flow

11 Chapter 11: Exterior Containment and Site Control

11.1 Exterior Ground Sheeting, Vertical Containment, and Weather Limits 11.2 Daily Exterior Cleanup, Paint-Chip Control, and Occupied/Multi-Family Logistics

12 Chapter 12: Component Replacement, Enclosure, and Encapsulation

12.1 Component Replacement 12.2 Enclosure Systems and Mechanical Fastening 12.3 Encapsulation Products, Unsuitable Surfaces, and Maintenance Schedules

13 Chapter 13: Paint Removal and Restricted Practices

13.1 Wet Scraping, Chemical Removal, and Heat Guns Below 1100°F 13.2 Restricted and Prohibited Practices 13.3 Selecting Methods, Combining Methods, and Documenting Why

14 Chapter 14: Interior Dust Abatement and Cleaning

14.1 Interior Dust Cleanup Sequence 14.2 Pre-Clearance Visual Inspection and When Cleanup Is Not Done

15 Chapter 15: Soil and Exterior Dust Abatement

15.1 Soil-Lead Hazards and Sampling Interpretation for Supervisors 15.2 Soil Removal and Replacement 15.3 Permanent Covering vs Landscaping

16 Chapter 16: OSHA 1926.62 Worker Protection

16.1 PEL, Action Level, and Exposure Assessment 16.2 Respiratory Protection, PPE, and Hygiene Facilities 16.3 Biological Monitoring and Medical Removal Protection 16.4 OSHA Competent Person Duties vs EPA Certified Supervisor Duties

17 Chapter 17: RCRA Waste Management

17.1 Abatement Waste Streams 17.2 TCLP Characterization and D008 17.3 Manifests, TSDF, Accumulation, and the Household Exclusion

18 Chapter 18: Action Levels, Post-Abatement Testing, and Records

18.1 Dust-Lead Action Levels vs Reportable-Level Hazards 18.2 Post-Abatement Visual, Dust Sampling, Independence, and the 1-Hour Wait 18.3 Failed Samples, Reclean/Retest, Exterior Visual, and Multi-Family Random Sampling 18.4 Abatement Report, 2026 Hazard Statement, Owner Copies, and 3-Year Retention

15.2 Soil Removal and Replacement

Key Takeaways Explain This Topic AI

If soil abatement is conducted by removal, the soil shall be replaced by soil with a lead concentration as close to local background as practicable, but no greater than 400 ppm, and the removed soil shall not be used as top soil at another residential property or child-occupied facility (40 CFR 745.227(e)(7)(i)).

40 CFR 745.227 does not specify an inch depth. HUD Guidelines Chapter 12 documented methodology is that removal of 6 inches of topsoil is adequate for most residential projects, with depth assessed at each site from sampling and expected use; urban contamination may extend 1 to 2 feet.

HUD Chapter 12 also specifies a water-permeable geotextile or similar liner as a visual demarcation at the excavation bottom, replacement grade about 2 inches above existing grade to allow for settling, and replacement soil below 400 µg/g (advising 200 µg/g or less where feasible).

Rototilling or other soil cultivation is not EPA soil abatement under 745.227(e)(7). That paragraph allows only removal-and-replacement or permanent covering.

Removed soil is a waste stream. Characterize and dispose of it under RCRA and state rules (Chapter 17). Do not spread it on a neighbor's garden, a daycare sandbox, or another residential yard as topsoil.

Last updated: August 2026

Take it out, put clean soil back, and do not donate the spoil

Quick Answer: If soil abatement is conducted, it shall be in one of two ways ( 40 CFR 745.227(e)(7) ). If the soil is removed: (A) it shall be replaced by soil with a lead concentration as close to local background as practicable, but no greater than 400 ppm ; (B) the soil that is removed shall not be used as top soil at another residential property or child-occupied facility . If soil is not removed, it shall be permanently covered (Section 15.3). 745.227 does not specify an inch depth. HUD Guidelines Chapter 12, as a documented methodology under 745.227(a)(3) , treats removal of 6 inches of topsoil as adequate for most residential projects, with depth assessed at each site from sampling and expected use.

Section 15.1 told you whether a play-area or rest-of-yard bare-soil hazard exists. This section is the removal path. Grass, mulch, and gravel are not this path. Rototilling 900 ppm play-area dirt into the subsoil is not this path. Dumping the excavated pile on the duplex next door as “free topsoil” is the exact (e)(7)(i)(B) violation the exam is built to catch.

Replacement soil at 400 ppm is the ceiling , not the target. The sentence is as close to local background as practicable, but no greater than 400 ppm . If background in that neighborhood is 80 ppm, 390 ppm fill is legal only in the thin sense that it is ≤ 400; it is not “as close as practicable.” HUD Chapter 12 advises that, where feasible, replacement soil be half or less of 400 — 200 µg/g or less — as a precautionary factor. That HUD preference does not rewrite EPA's 400 ppm cap.

EPA's two sentences; HUD's inches

745.227(e)(7)(i) is short on purpose. It does not say 2 inches, 6 inches, or 24 inches. Supervisors follow the documented methodology and the specifications in the work plan.

Issue EPA 745.227(e)(7) HUD Guidelines Chapter 12 (documented methodology)

When this method applies Soil abatement , if conducted , by removal Soil treatments expected to last ≥ 20 years ; Guidelines also discuss when abatement is “most appropriate” at very high concentrations (e.g., ≥ 5,000 µg/g ) — that is not the EPA hazard trigger

Replacement concentration As close to local background as practicable, no greater than 400 ppm Must be < 400 µg/g ; advise 200 µg/g or less where feasible

Reuse of spoil Shall not be used as top soil at another residential property or child-occupied facility Manifest the load so contaminated soil is not used as fill in other residential areas

Depth Not specified For most soil-removal projects, 6 inches of topsoil is adequate; contamination is usually the top few inches ; urban sites may go 1–2 feet ; assess depth of contamination and usual disturbance (gardening); for most residential grass/shrub/shallow-garden yards, depth will not exceed 6 inches

Marker Silent Water-permeable geotextile (or similar) at the excavation bottom as a visual demarcation so later diggers do not mix dirty subsoil into the clean cap

Finish grade Silent Replacement soil about 2 inches above existing grade to allow for settling and to drain away from the structure

Cultivation Not an (e)(7) method Rototilling is not recommended in the Chapter 12 how-to; mixing is discussed only as a separate strategy when averages are already below 1,200 µg/g — not EPA abatement

How deep — the exam answer. If the question asks what EPA 745.227 requires for inches, the honest answer is it does not specify . If the question asks what HUD Chapter 12 uses as the usual residential cut, the answer is 6 inches of topsoil , unless sampling and use (deep gardens, former building pads, industrial fill) show contamination deeper. Do not excavate 24 inches on every sandbox because it feels thorough, and do not skim 2 inches of a 6-inch contaminated profile and call the job done because “EPA never said 6.” The specification, the RA's depth data if collected, and HUD's documented methodology fill the silence.

Worked example — play-area 900 ppm, 4-inch dirty cap. Cores show lead dropping below 400 ppm below about 4 inches. HUD's usual 6-inch cut still makes sense so the remaining profile is not nicked by later play and so the geotextile sits in clean-enough material. Replacement soil tests 120 ppm , local background about 90 ppm — as close as practicable and ≤ 400 . Finish 2 inches high , sod it, keep children off until the cover is established.

Worked example — urban 18-inch contamination. The lot sits on decades of painted-building debris. Cores stay high to 18 inches . HUD says urban contamination may extend 1 or 2 feet and that depth of usual disturbance (here, vegetable beds) drives the cut. The spec removes 18 inches , places geotextile, and replaces with ≤ 400 ppm soil. A 6-inch skim that leaves 2,000 ppm at 8 inches for the first tomato planting is not “HUD 6 inches always.”

How to run a removal day (HUD Chapter 12 field sequence)

Accredited courses teach HUD's how-to because 745.227(a)(3) points you there:

Confirm the hazard and the method from the RA and the contract (play area vs rest of yard; remove vs pave).

Test replacement soil before it arrives — ≤ 400 ppm , as close to background as practicable.

Call 811 / utility locate. Mark water, gas, electric, cable, sewer. HUD: protect utilities; the owner or contractor makes good any damage.

Site control. Temporary fence or barricades, caution tape, keep unauthorized people and animals out. Maintain a lead-safe path to the dwelling that does not cross the excavation. HUD: finish a given site in one workday when you can, because overnight bare contaminated soil is a child-access problem.

Do not leave spoil piles overnight. Cover if you must pause; high wind and rain move contaminated soil off-site. Suspend work when weather defeats control.

Load once. Wheelbarrows or small equipment into tarped , sealed-tailgate trucks or roll-offs. Brush soil off tires on plastic before the truck leaves. HUD: no double-handling that spreads dirt across the walk.

Separate tools (or decontaminate) so clean fill is not placed with dirty shovels.

Geotextile on the excavation bottom. Replace to the specified depth and 2 inches above existing grade, draining away from the house.

Clean adjacent hard surfaces — walks, drives, street — of loose contaminated soil before clean fill goes down, and again at day's end (scrape, wash, vacuum/wet-sweep).

Keep records of sampling and the cut depth with the property file so a later sewer trench does not smear dirty subsoil onto the new cap.

Occupant protection (Chapter 8) still applies: children do not play in the open excavation. Exterior containment logic from Chapter 11 still applies: you are moving contaminated material; do not track it onto the porch and into the living room.

Cultivation is a trap. HUD Chapter 12 discusses rototilling as a possible mixing strategy when the average is already below 1,200 µg/g. EPA soil abatement is not that option. If the job is abatement under (e)(7), you remove and replace or you permanently cover . Mixing 900 ppm play-area soil with cleaner dirt underneath does not meet (e)(7)(i) or (ii).

The excavated soil is waste — not landscape material

(e)(7)(i)(B) is a complete sentence: removed soil shall not be used as top soil at another residential property or child-occupied facility . That bans the friendly dump on the neighbor's garden, the daycare sandbox “refresh,” and the church playground fill. It also bans using the spoil as topsoil on this owner's other rental two streets over.

The spoil is still a waste stream . Chapter 17 owns TCLP, D008 (≥ 5 mg/L lead), manifests, and the household exclusion. HUD Chapter 12: use a load-ticket / manifest system so the dirt is not quietly used as residential fill; TCLP may make the load hazardous . States may be stricter. Never open-burn it. Never throw it in a storm drain. Never stockpile it on the play area as the “new” surface.

Worked example — the neighbor's garden. Crew finishes a 900 ppm sandbox excavation at 3 p.m. The helper offers the dark loam to the next-door gardener. That reuse is (e)(7)(i)(B) regardless of how nice the loam looks. It goes to a lawful disposal or treatment path, characterized as Chapter 17 requires — not across the property line as topsoil.

Worked example — 450 ppm “clean” fill. A landscape supplier's fill tests 450 ppm . It fails (e)(7)(i)(A) even if local background is 500 ppm, because replacement may be no greater than 400 ppm . Find another source. Do not average the 450 ppm fill with 50 ppm compost in the truck and call it 250 without a real, documented blend and a new lab result.

Official sources: 40 CFR 745.227(e)(7), (a)(3) ; HUD Guidelines Chapter 12, Soil and Exterior Dust Abatement (typical 6-inch topsoil removal, site-specific depth, geotextile, 2-inch over-grade, replacement < 400 µg/g / advise 200 µg/g ).

Loading diagram... Soil Removal: Depth from HUD Methodology, Replacement ≤ 400 ppm, No Residential Reuse