Study guide

14.1 Weight Definitions & Structural Limitations

FAA ADX Aircraft Dispatcher Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Regulations & Dispatcher Certification (14 CFR Part 65)

1.1 14 CFR Part 65 Eligibility, Privileges, Limitations & Retesting 1.2 Operational Control & Shared Dispatcher-PIC Responsibility 1.3 Dispatch Release Requirements, Amendments & Records

2 Chapter 2: Part 121 Domestic, Flag & Supplemental Operating Rules

2.1 Domestic vs. Flag vs. Supplemental Operational Rules 2.2 Dispatch Weather Minimums & Departure Rules 2.3 Takeoff Alternates & Clean Aircraft Concept

3 Chapter 3: Destination Alternates, Alternate Minimums & Redispatch

3.1 Destination Alternate Requirements (1-2-3 Rule & Flag/Supplemental) 3.2 Alternate Airport Weather Minimums (OpSpecs Table C055) 3.3 Marginal Weather Rule & Second Alternate Selection 3.4 En Route Redispatch & Reclearance Procedures

4 Chapter 4: Dispatcher & Flightcrew Duty Limitations and Rest (14 CFR § 121.465 & Part 117)

4.1 Dispatcher Duty Time Limitations & Rest Requirements 4.2 Flightcrew Duty & Rest Requirements (14 CFR Part 117) 4.3 Dispatcher Qualifications, Recurrent Training & Operating Familiarization

5 Chapter 5: Minimum Equipment Lists (MEL), CDL & Maintenance Dispatch

5.1 Master Minimum Equipment List (MMEL) & Operator MEL 5.2 Configuration Deviation List (CDL) & Missing Secondary Airframe Parts 5.3 Dispatch with Inoperative Equipment, Logbooks & Special Flight Permits

6 Chapter 6: Aviation Meteorology — Atmosphere, Pressure Systems & Fronts

6.1 Atmospheric Structure, Pressure Systems & Altimetry 6.2 Air Masses & Frontal Systems 6.3 Clouds, Atmospheric Stability & Fog 6.4 Earth Motion, Global Circulation & Regional/Local Weather Regimes

7 Chapter 7: Hazardous Aviation Weather — Convection, Icing & Turbulence

7.1 Thunderstorms & Severe Convection 7.2 Structural & Induction Icing 7.3 Turbulence, Jet Streams & Clear Air Turbulence (CAT) 7.4 Low-Level Windshear & Microburst Detection Systems

8 Chapter 8: Aviation Weather Products, Observations & Forecasts

8.1 Surface Weather Observations (METAR & SPECI) 8.2 Terminal Aerodrome Forecasts (TAF) 8.3 In-Flight Weather Advisories (PIREPs, AIRMETs, SIGMETs) 8.4 Upper-Air Analysis & Prognostic Weather Charts

9 Chapter 9: Airspace Structure, Air Traffic Control & Traffic Management

9.1 Airspace Classes & Operating Rules 9.2 Special Use Airspace & Temporary Flight Restrictions 9.3 Air Traffic Control Flow Management & Initiatives 9.4 NOTAM System & Airport Field Condition Reporting 9.5 Flight Plan Filing: Domestic and International (ICAO) Flight Plans

10 Chapter 10: IFR Navigation, Airway Structure & Charting

10.1 Ground-Based Navigation Facilities (VOR, TACAN, DME, ILS) 10.2 RNAV, RNP & Performance-Based Navigation (PBN) 10.3 En Route IFR Charts & High/Low Airway Navigation 10.4 Earth Reference, Time Standards, Chart Projections & Great-Circle Navigation

11 Chapter 11: Terminal Instrument Procedures — SIDs, STARs & Approaches

11.1 Standard Instrument Departures (SIDs) & Obstacle Departure Procedures (ODPs) 11.2 Standard Terminal Arrival Routes (STARs) & En Route Transitions 11.3 Instrument Approach Procedures & Minimums 11.4 Holding Procedures & Holding Pattern Calculations

12 Chapter 12: High-Altitude Transonic Aerodynamics & Jet Characteristics

12.1 Transonic Flow, Mach Number & Compressibility 12.2 Shock Waves, Mach Tuck & Shock Stall 12.3 Coffin Corner, Buffet Boundaries & Swept-Wing Aerodynamics

13 Chapter 13: Transport Category Turbine Aircraft Systems

13.1 Turbine Powerplants & Auxiliary Power Units 13.2 Electrical, Hydraulic & Pneumatic Systems 13.3 Pressurization, Environmental Control & Oxygen Systems 13.4 Flight Management Systems (FMS), Autoflight & Avionics

14 Chapter 14: Aircraft Weight, Balance & Loading

14.1 Weight Definitions & Structural Limitations 14.2 Center of Gravity (CG) Principles & Computations 14.3 Cargo Loading, Floor Load Limits & Load Manifests

15 Chapter 15: Transport Category Aircraft Performance & Limitations

15.1 Takeoff Performance & V-Speeds 15.2 Climb Gradients, Obstacle Clearance & Runway Limitations 15.3 En Route Engine Inoperative Performance & Drift-Down 15.4 Landing Performance & Runway Condition Assessment

16 Chapter 16: Practical Dispatch Flight Planning, Fuel Strategy & Emergencies

16.1 Domestic, Flag & Supplemental Fuel Requirements 16.2 Flight Planning, Route Selection & Equal Time Point (ETP) / PNR 16.3 Emergency Procedures, In-Flight Diversions & Security Threats 16.4 NTSB Part 830 Incident & Accident Notification Procedures 16.5 Flight Following, Overdue Aircraft & Post-Flight Duties

17 Chapter 17: Human Factors, ADM, CRM & Dispatch Communications

17.1 Human Factors & Human Error in Airline Dispatch 17.2 Aeronautical Decision Making, Judgment & Risk Management 17.3 Crew Resource Management, Dispatch Teamwork & Briefing Technique 17.4 Dispatch Communications, Data Link & Aeronautical Publications

14.1 Weight Definitions & Structural Limitations

Key Takeaways Explain This Topic AI

Basic Empty Weight (BEW) comprises standard airframe structure, powerplants, permanent systems, unusable fuel, and full operating fluids (oil and hydraulics); Operating Empty Weight (OEW / Dry Operating Weight DOW) adds operational crew, crew baggage, passenger service items, emergency equipment, potable water, and lavatory chemicals, strictly excluding usable fuel and payload.

Zero Fuel Weight (ZFW) equals OEW plus total payload (passengers, baggage, cargo); Maximum Zero Fuel Weight (MZFW) is a rigid 14 CFR Part 25 structural limit governed by wing root bending moment—because upward wing lift is opposed by fuel weight in the wing tanks, excess weight concentrated in the fuselage without wing fuel relief overstresses the wing root spars.

Maximum Ramp Weight (MRW / Taxi Weight) is the certified maximum gross weight for ground maneuvering and taxi; Maximum Takeoff Weight (MTOW / MGTOW) is the maximum certified weight authorized at brake release for takeoff, where MTOW = MRW - Taxi Fuel Allowance.

Maximum Landing Weight (MLW) is the certified maximum weight for touchdown at a design sink rate of 10 feet per second per 14 CFR § 25.473; dispatching an aircraft at a takeoff weight exceeding MLW plus En Route Trip Fuel violates 14 CFR § 121.195, requiring in-flight fuel dumping or an overweight landing structural inspection.

Maximum Allowable Takeoff Weight (MATOW) for flight release under 14 CFR Part 121 is legally restricted to the lowest of four independent boundaries: (1) Structural MTOW, (2) Performance-limited MTOW (field length, climb gradients, obstacle clearance, tire speed, brake energy), (3) Structural MLW plus En Route Trip Fuel, and (4) Structural MZFW plus Takeoff Fuel.

Last updated: September 2026

14.1 Weight Definitions & Structural Limitations

In transport-category airline operations governed by 14 CFR Part 121 and certified under 14 CFR Part 25 , precise aircraft weight determination is not merely an accounting exercise—it is a life-critical engineering and operational discipline. The certificated aircraft dispatcher shares joint legal responsibility with the pilot-in-command (PIC) under 14 CFR § 121.533 for the operational control, flight planning, and regulatory compliance of every flight release. A primary dispatcher function is verifying that the aircraft's gross weight remains strictly within certified structural thresholds and aerodynamic performance limitations throughout every phase of flight: ramp pushback, taxi, takeoff roll, en route climb, cruise, descent, and landing touchdown.

Operating an aircraft above certified weight thresholds introduces severe safety hazards, including structural airframe deformation, wing spar fatigue, reduced climb gradients over obstacles, dangerously prolonged takeoff and landing ground runs, tire blowouts due to excessive rotational speeds, and brake assembly meltdown during rejected takeoffs. This section breaks down the statutory weight taxonomy, the fuel hierarchy, the structural physics of wing root bending moment relief, and the four-part calculation required to establish the legal Maximum Allowable Takeoff Weight (MATOW) .

The Transport Category Aircraft Weight Taxonomy

To ensure unambiguous communication across flight operations, ground operations, and flight planning systems, the FAA and aeronautical manufacturers categorize aircraft gross weight into standardized, cumulative classifications: +-----------------------------------------------------------------------------------+

  • | MAXIMUM RAMP WEIGHT (MRW) |
  • +-----------------------------------------------------------------+-----------------+
  • | MAXIMUM TAKEOFF WEIGHT (MTOW) | TAXI FUEL |
  • +-----------------------------------------------+-----------------+-----------------+
  • | ZERO FUEL WEIGHT (ZFW) | TAKEOFF FUEL | |
  • +-----------------------+-----------------------+ (Trip + Reserve)| |
  • | OPERATING EMPTY | PAYLOAD | | |
  • | WEIGHT (OEW) | (Passengers + Cargo) | | |
  • +-----------+-----------+ | | |
  • | BASIC | OPERATING | | | |
  • | EMPTY | ITEMS | | | |
  • | (BEW) | | | | |
  • +-----------+-----------+-----------------------+-----------------+-----------------+
  • 1. Manufacturer Empty Weight (MEW) & Basic Empty Weight (BEW)

Manufacturer Empty Weight (MEW) : The weight of the physical aircraft structure, powerplants, systems, furnishings, and equipment as delivered by the manufacturer, before any operator-specific equipment or unusable fluids are installed.

Basic Empty Weight (BEW) : The starting baseline for all airline weight and balance records. BEW comprises:

The complete airframe structure and installed powerplants.

All permanently installed avionics, instrumentation, and cabin furnishings.

Unusable fuel (the small quantity of fuel trapped in tank sumps, pumps, and plumbing lines that cannot be drained or utilized by the engines in flight).

Full operating fluids : engine lubricating oil, hydraulic system fluids, transmission fluids, and fixed fire-extinguishing agents.

2. Operating Empty Weight (OEW) / Dry Operating Weight (DOW)

Operating Empty Weight (OEW) —referred to in ICAO and European operations as Dry Operating Weight (DOW) —represents the baseline weight of the aircraft configured and ready for revenue flight, but completely devoid of payload and usable fuel . OEW equals BEW plus all operational airline items:

Flight crew and cabin crew : Pilots, flight attendants, and their mandated luggage.

Passenger service equipment and catering : Galleys, food carts, beverage supplies, coffee makers, dry goods, blankets, pillows, and magazines.

Consumable fluids : Full potable water tanks and lavatory flush chemical pre-charges.

Mandatory emergency and survival equipment : Life rafts, life vests, emergency medical kits, portable oxygen bottles, slide rafts, and crash axes.

Flyaway kits / spare parts : Aircraft-specific tools, spare tire assemblies, or towbar fittings carried onboard for remote outstation operations.

Note

Dispatch Rule : OEW is a relatively stable figure for a specific airframe tail number, but it varies between aircraft within the same fleet based on interior cabin configuration (e.g., high-density domestic seating vs. lie-flat international business class suites).

3. Payload (Revenue and Non-Revenue Traffic)

Payload is the total weight of revenue-generating and non-revenue traffic carried aboard the aircraft. Payload consists of:

Passengers (PAX) : Calculated using approved standard average weights under FAA Advisory Circular AC 120-27F or actual passenger scale weights for charter operations.

Checked Baggage : Baggage stowed in lower-deck cargo compartments, calculated via standard baggage weights (typically 30 lbs per domestic bag, 40 lbs per international bag, and 60 lbs for heavy bags).

Carry-On Baggage : Personal items and rolling bags brought into the passenger cabin (accounted for within FAA average adult passenger weights).

Cargo and Freight : Commercial mail, express parcels, palletized freight, and company material (COMAT) secured in certified cargo holds.

FAA Standard Average Passenger Weights (AC 120-27F)

Under approved Part 121 Weight and Balance Control Programs, airlines utilize standard average passenger weights that account for seasonal clothing variations:

  • Passenger Category Summer (May 1 – Oct 31) Winter (Nov 1 – Apr 30) Includes Personal / Carry-On Allowance
  • Adult (Combined Male/Female) 190 lbs (86.2 kg) 195 lbs (88.5 kg) Yes (16 lbs carry-on + personal item)
  • Adult Male 200 lbs (90.7 kg) 205 lbs (93.0 kg) Yes (16 lbs carry-on + personal item)
  • Adult Female 179 lbs (81.2 kg) 184 lbs (83.5 kg) Yes (16 lbs carry-on + personal item)
  • Child (Ages 2 through 12) 82 lbs (37.2 kg) 87 lbs (39.5 kg) Yes
  • Plane-Side Checked Bag 30 lbs (13.6 kg) 30 lbs (13.6 kg) Gate-checked rollaboard bags
  • 4. Zero Fuel Weight (ZFW)

Zero Fuel Weight (ZFW) is the total weight of the aircraft including all payload, operational crew, and equipment, but strictly excluding all usable fuel : ZFW = OEW + Payload \text{ZFW} = \text{OEW} + \text{Payload} ZFW = OEW + Payload

ZFW is the weight supported entirely by the aircraft fuselage structure while resting on the ground or in flight prior to fuel load considerations.

The Fuel Hierarchy & Operational Categories

In turbine transport aircraft flight planning, total fuel onboard is divided into distinct functional segments governed by 14 CFR §§ 121.639, 121.641, 121.643, and 121.645 :

Ramp Fuel (Total Fuel Onboard) : The total quantity of usable fuel loaded into the aircraft fuel tanks at the gate prior to engine start.

Taxi Fuel (Ground Burn) : The estimated fuel consumed by the Auxiliary Power Unit (APU) at the gate, engine startup, pushback, and ground taxi maneuvering to the departure runway threshold (typically 500 to 1,500 lbs for narrow-body aircraft, 1,500 to 3,500 lbs for wide-body aircraft).

Takeoff Fuel : The actual usable fuel remaining at brake release for takeoff: Takeoff Fuel = Ramp Fuel − Taxi Fuel \text{Takeoff Fuel} = \text{Ramp Fuel} - \text{Taxi Fuel} Takeoff Fuel = Ramp Fuel − Taxi Fuel

Trip Fuel (En Route Burnoff) : The calculated fuel consumed from brake release at the departure airport, through climb, cruise, descent, approach, and touchdown at the destination airport.

Reserve Fuel : The mandatory legal reserve fuel that must remain intact upon touchdown at the destination or alternate airport:

Domestic Operations (14 CFR § 121.639) : Fuel to fly for 45 minutes at normal cruising fuel consumption.

Flag Operations (14 CFR § 121.645) : Fuel to fly for 10% of total en route flight time , plus fuel to the most distant alternate airport, plus 30 minutes of holding at 1,500 feet above the alternate airport under standard conditions.

Alternate Fuel : Fuel required to execute a missed approach at the destination airport, climb to en route altitude, fly the routing to the designated alternate airport, conduct the approach, and land.

Contingency / Extra Fuel : Discretionary fuel added by the dispatcher or PIC for expected ATC traffic management initiatives (EDCT ground delays, route diversions, holding, or headwinds).

Landing Fuel (Fuel Over Destination) : Total fuel remaining upon touchdown at the destination: Landing Fuel = Takeoff Fuel − Trip Fuel = Reserve Fuel + Alternate Fuel + Contingency Fuel \text{Landing Fuel} = \text{Takeoff Fuel} - \text{Trip Fuel} = \text{Reserve Fuel} + \text{Alternate Fuel} + \text{Contingency Fuel} Landing Fuel = Takeoff Fuel − Trip Fuel = Reserve Fuel + Alternate Fuel + Contingency Fuel

Certified Structural Weight Limitations

Under 14 CFR Part 25 , every transport category aircraft is certified with four primary maximum structural weight limits published in the FAA-approved Airplane Flight Manual (AFM). These limits are immutable airframe boundaries that cannot be exceeded under any operational circumstance:

1. Maximum Ramp Weight (MRW) / Maximum Taxi Weight (MTW)

The maximum certified gross weight authorized for ground maneuvering, pushback, and taxiing between the ramp and the runway. MRW accounts for the structural strength of the landing gear shock struts, taxiway pavement bearing capacity, and low-speed ground turning loads. The difference between MRW and Maximum Takeoff Weight represents the structural allowance for taxi fuel burn.

2. Maximum Takeoff Weight (MTOW / MGTOW)

The maximum certified gross weight authorized at the exact moment of brake release for takeoff roll. MTOW is governed by primary airframe structural load limits (wing spars, fuselage frames, landing gear attachment trunnions) under takeoff acceleration and dynamic runway bump loads.

3. Maximum Landing Weight (MLW)

The maximum certified gross weight authorized for touchdown under normal operational landing conditions. MLW is determined under 14 CFR § 25.473 , which mandates that landing gear and wing structure withstand a design sink rate of 10 feet per second (600 feet per minute) at MLW, but only 6 feet per second (360 feet per minute) at MTOW. Because landing generates intense dynamic impact deceleration forces, MLW is substantially lower than MTOW (often 15% to 25% lower).

4. Maximum Zero Fuel Weight (MZFW)

The maximum certified weight of the aircraft before any usable fuel is loaded into the tanks. MZFW is the maximum allowable combined weight of the Operating Empty Weight plus total payload: ZFW = OEW + Payload ≤ MZFW \text{ZFW} = \text{OEW} + \text{Payload} \le \text{MZFW} ZFW = OEW + Payload ≤ MZFW

Deep Dive: Wing Root Bending Moment & Fuel Relief Physics

A fundamental concept tested heavily on the FAA ADX exam is the engineering rationale for Maximum Zero Fuel Weight (MZFW) . Why does the FAA certify a rigid limit on fuselage weight that is tens of thousands of pounds below the Maximum Takeoff Weight, while permitting the aircraft to take off at a much higher gross weight simply by adding fuel?

The Aerodynamic Force Balance in Flight

An aircraft wing behaves as a structural cantilever beam anchored to the fuselage at the wing root spar :

Upward Aerodynamic Lift : During level cruise flight, total wing lift must equal total aircraft weight ( L = W L = W L = W ). This upward lift force is generated across the wingspan, acting upward against the bottom of the wing panels.

Downward Fuselage Weight : The entire weight of the fuselage—consisting of the passenger cabin, cargo holds, flight deck, and fuselage structure (the Zero Fuel Weight)—acts as a massive, concentrated downward load concentrated in the center of the airframe.

The Wing Root Bending Moment : The upward lift acting on the wings combined with the heavy downward load of the fuselage creates an immense upward rotational force at the wing root spar, bending the wing tips upward. This is known as the wing root bending moment .

Fuel Relief of Wing Bending Moment

Transport aircraft store the vast majority of their fuel inside integral wing fuel tanks (inner wing, outer wing, and wing tip tanks) distributed across the wingspan:

The physical weight of fuel stored inside the wing acts as a downward gravitational force distributed along the wing span .

This downward fuel weight directly counteracts and opposes the upward aerodynamic lift forces acting on that same wing section.

Consequently, the downward weight of fuel in the wings relieves the upward bending moment exerted on the wing root attachment spars! IN-FLIGHT STRUCTURAL FORCE BALANCE

  • [ Upward Aerodynamic Lift Distributed Along Wingspan (L) ]
  • ^ ^ ^
  • | | |
  • +---------+------------------+------------------+---------+
  • | Wing Tip Tank Main Wing Tank Center Tank |
  • | [Fuel ↓] [Fuel ↓] |
  • +----------------------------+----------------------------+
  • | Wing Root Spar
  • v (Wing Bending Moment Relieved by Wing Fuel)
  • +-------------------+
  • | FUSELAGE / CABIN |
  • | OEW + PAYLOAD |
  • | (ZFW Load) |
  • | ↓↓↓ |
  • +-------------------+
  • The Engineering Implication of MZFW

Because fuselage payload (passengers and cargo) is concentrated entirely inside the fuselage, it contributes 100% to the upward wing root bending moment without providing any relieving downward force along the wingspan. If an airline were allowed to load payload up to the Maximum Takeoff Weight without fuel, the wing root spars would crack or shear off due to excessive upward bending stress during a 2.5-G gust encounter.

Therefore, 14 CFR Part 25 establishes MZFW as the structural limit of the wing root spar . Once an aircraft is loaded to its MZFW:

Not a single additional pound of cargo or passenger weight may be loaded into the fuselage.

Any additional weight added to the aircraft up to MTOW must consist exclusively of fuel loaded into the wing tanks , because the fuel provides its own structural relief to offset its additional weight.

Calculating Maximum Allowable Takeoff Weight (MATOW)

In airline dispatch operations, the dispatcher must never assume that an aircraft can depart at its structural MTOW. Under 14 CFR Part 121 , the legal Maximum Allowable Takeoff Weight (MATOW) for flight plan release is governed by the most restrictive (lowest) of four independent engineering and operational constraints: MATOW = min ⁡ { Structural MTOW Performance-Limited Takeoff Weight Structural MLW + En Route Trip Fuel Structural MZFW + Takeoff Fuel \text{MATOW} = \min \begin{cases} \text{Structural MTOW} \\ \text{Performance-Limited Takeoff Weight} \\ \text{Structural MLW} + \text{En Route Trip Fuel} \\ \text{Structural MZFW} + \text{Takeoff Fuel} \end{cases} MATOW = min ⎩ ⎨ ⎧ ​ Structural MTOW Performance-Limited Takeoff Weight Structural MLW + En Route Trip Fuel Structural MZFW + Takeoff Fuel ​

The Four Governing Takeoff Weight Constraints

Structural MTOW : The certified maximum structural takeoff limit established in the AFM.

Performance-Limited MTOW (Runway / Climb Limit) : The maximum weight permitted by environmental and runway conditions at the departure airport under 14 CFR §§ 121.189 and 25.101–25.125 . This accounts for:

Available runway length (accelerate-stop and accelerate-go balanced field requirements).

Pressure altitude and ambient temperature ( O A T OAT O A T ) affecting engine thrust and air density.

Headwind or tailwind components and runway surface contamination (water, snow, ice).

Second-segment climb gradient requirements (minimum 2.4% gross climb for two-engine aircraft with one engine inoperative).

Obstacle clearance profiles along the departure flight path.

Maximum tire speed ratings (e.g., 204 or 225 knots groundspeed limits).

Maximum brake energy absorption limits during high-speed rejected takeoffs.

Landing Weight Limit Adjusted for Burnoff (MLW + Trip Burn) : Under 14 CFR § 121.195 , an aircraft cannot depart at a takeoff weight that would cause its weight upon arrival at the destination to exceed the certified Maximum Landing Weight (MLW) (or the runway performance-limited landing weight at the destination), after accounting for normal en route trip fuel burnoff: Takeoff Limit MLW = Structural MLW + En Route Trip Fuel \text{Takeoff Limit}_{\text{MLW}} = \text{Structural MLW} + \text{En Route Trip Fuel} Takeoff Limit MLW ​ = Structural MLW + En Route Trip Fuel

Zero Fuel Weight Limit Adjusted for Fuel (MZFW + Takeoff Fuel) : To guarantee that the aircraft fuselage does not exceed structural bending limits, the takeoff weight cannot exceed the Maximum Zero Fuel Weight plus the actual takeoff fuel loaded: Takeoff Limit MZFW = Structural MZFW + Takeoff Fuel \text{Takeoff Limit}_{\text{MZFW}} = \text{Structural MZFW} + \text{Takeoff Fuel} Takeoff Limit MZFW ​ = Structural MZFW + Takeoff Fuel

Step-by-Step Dispatch Calculation Scenario

An aircraft dispatcher is releasing Flight 412, operated with a twin-engine transport category turbojet from Chicago O'Hare (ORD) to Denver (DEN). The dispatcher compiles the following operational data:

  • Baseline Aircraft & Payload Data
  • Operating Empty Weight (OEW) : 98 , 500 lbs 98,500\text{ lbs} 98 , 500 lbs

Booked Passenger Payload : 142 passengers @ 190 lbs average (summer) = 26 , 980 lbs 26,980\text{ lbs} 26 , 980 lbs

Checked Baggage & Cargo : 10 , 220 lbs 10,220\text{ lbs} 10 , 220 lbs

Total Payload : 26 , 980 + 10 , 220 = 37 , 200 lbs 26,980 + 10,220 = 37,200\text{ lbs} 26 , 980 + 10 , 220 = 37 , 200 lbs

Planned Zero Fuel Weight (ZFW) : 98 , 500 + 37 , 200 = 135 , 700 lbs 98,500 + 37,200 = \mathbf{135,700\text{ lbs}} 98 , 500 + 37 , 200 = 135 , 700 lbs

  • Certified Structural Limits
  • Maximum Ramp Weight (MRW) : 175 , 000 lbs 175,000\text{ lbs} 175 , 000 lbs
  • Maximum Takeoff Weight (MTOW) : 174 , 200 lbs 174,200\text{ lbs} 174 , 200 lbs
  • Maximum Landing Weight (MLW) : 146 , 300 lbs 146,300\text{ lbs} 146 , 300 lbs
  • Maximum Zero Fuel Weight (MZFW) : 138 , 000 lbs 138,000\text{ lbs} 138 , 000 lbs
  • Fuel Planning Parameters
  • En Route Trip Fuel (ORD to DEN) : 18 , 400 lbs 18,400\text{ lbs} 18 , 400 lbs
  • Alternate Airport Fuel (Colorado Springs - COS) : 3 , 200 lbs 3,200\text{ lbs} 3 , 200 lbs
  • FAR 121 Domestic Reserve (45 min) : 4 , 000 lbs 4,000\text{ lbs} 4 , 000 lbs
  • Contingency / Extra Fuel : 1 , 000 lbs 1,000\text{ lbs} 1 , 000 lbs

Total Takeoff Fuel Required : 18 , 400 + 3 , 200 + 4 , 000 + 1 , 000 = 26 , 600 lbs 18,400 + 3,200 + 4,000 + 1,000 = \mathbf{26,600\text{ lbs}} 18 , 400 + 3 , 200 + 4 , 000 + 1 , 000 = 26 , 600 lbs

Estimated Taxi Fuel : 800 lbs 800\text{ lbs} 800 lbs

Required Ramp Fuel : 26 , 600 + 800 = 27 , 400 lbs 26,600 + 800 = \mathbf{27,400\text{ lbs}} 26 , 600 + 800 = 27 , 400 lbs

Environmental & Airport Performance

Departure Runway 28R Performance-Limited Takeoff Weight : 169 , 500 lbs \mathbf{169,500\text{ lbs}} 169 , 500 lbs (restricted by high summer ambient temperature of + 32 ∘ C +32^\circ\text{C} + 3 2 ∘ C and second-segment climb gradient).

Step 1: Verify Zero Fuel Weight Compliance Planned ZFW = 135 , 700 lbs ≤ Structural MZFW ( 138 , 000 lbs ) \text{Planned ZFW} = 135,700\text{ lbs} \le \text{Structural MZFW } (138,000\text{ lbs}) Planned ZFW = 135 , 700 lbs ≤ Structural MZFW ( 138 , 000 lbs )

Status: Legal . The aircraft is operating 2 , 300 lbs 2,300\text{ lbs} 2 , 300 lbs below its structural MZFW.

  • Step 2: Evaluate the Four Governing Takeoff Constraints
  • Structural MTOW : 174 , 200 lbs \mathbf{174,200\text{ lbs}} 174 , 200 lbs
  • Runway Performance-Limited MTOW : 169 , 500 lbs \mathbf{169,500\text{ lbs}} 169 , 500 lbs

Landing Weight Limit (Structural MLW + Trip Fuel) : Limit MLW = 146 , 300 + 18 , 400 = 164 , 700 lbs \text{Limit}_{\text{MLW}} = 146,300 + 18,400 = \mathbf{164,700\text{ lbs}} Limit MLW ​ = 146 , 300 + 18 , 400 = 164 , 700 lbs

Zero Fuel Weight Limit (Structural MZFW + Takeoff Fuel) : Limit MZFW = 138 , 000 + 26 , 600 = 164 , 600 lbs \text{Limit}_{\text{MZFW}} = 138,000 + 26,600 = \mathbf{164,600\text{ lbs}} Limit MZFW ​ = 138 , 000 + 26 , 600 = 164 , 600 lbs

Step 3: Determine Governing MATOW

Comparing the four limits:

  • Structural MTOW: 174 , 200 lbs 174,200\text{ lbs} 174 , 200 lbs
  • Performance MTOW: 169 , 500 lbs 169,500\text{ lbs} 169 , 500 lbs
  • MLW + Trip Fuel: 164 , 700 lbs 164,700\text{ lbs} 164 , 700 lbs
  • MZFW + Takeoff Fuel: 164 , 600 lbs 164,600\text{ lbs} 164 , 600 lbs

The lowest, most restrictive limit is 164 , 600 lbs 164,600\text{ lbs} 164 , 600 lbs , governed by Structural MZFW + Takeoff Fuel ! MATOW = 164 , 600 lbs \mathbf{\text{MATOW} = 164,600\text{ lbs}} MATOW = 164 , 600 lbs

Step 4: Verify Planned Takeoff Weight vs MATOW

Planned Takeoff Weight (PTOW) = Planned ZFW ( 135 , 700 lbs 135,700\text{ lbs} 135 , 700 lbs ) + Takeoff Fuel ( 26 , 600 lbs 26,600\text{ lbs} 26 , 600 lbs ) = 162 , 300 lbs \mathbf{162,300\text{ lbs}} 162 , 300 lbs .

Margin Below MATOW = 164 , 600 − 162 , 300 = 2 , 300 lbs 164,600 - 162,300 = 2,300\text{ lbs} 164 , 600 − 162 , 300 = 2 , 300 lbs allowable under the release.

Planned Landing Weight (PLW) = Planned PTOW ( 162 , 300 lbs 162,300\text{ lbs} 162 , 300 lbs ) - Trip Fuel ( 18 , 400 lbs 18,400\text{ lbs} 18 , 400 lbs ) = 143 , 900 lbs \mathbf{143,900\text{ lbs}} 143 , 900 lbs .

Landing Margin Below MLW = 146 , 300 − 143 , 900 = 2 , 400 lbs 146,300 - 143,900 = 2,400\text{ lbs} 146 , 300 − 143 , 900 = 2 , 400 lbs under structural MLW.

Planned Ramp Weight = Planned PTOW ( 162 , 300 lbs 162,300\text{ lbs} 162 , 300 lbs ) + Taxi Fuel ( 800 lbs 800\text{ lbs} 800 lbs ) = 163 , 100 lbs ≤ 175 , 000 lbs \mathbf{163,100\text{ lbs}} \le 175,000\text{ lbs} 163 , 100 lbs ≤ 175 , 000 lbs (MRW). DISPATCH WEIGHT AUDIT SUMMARY

  • Constraint Parameter Limit (lbs) Planned (lbs) Margin (lbs) Compliance
  • ----------------------------------------------------------------------------------------
  • Zero Fuel Weight (ZFW) 138,000 135,700 +2,300 LEGAL
  • Ramp Weight (MRW) 175,000 163,100 +11,900 LEGAL
  • Takeoff Weight vs MATOW 164,600 162,300 +2,300 LEGAL
  • Destination Landing (MLW) 146,300 143,900 +2,400 LEGAL
  • ----------------------------------------------------------------------------------------
  • Governing Takeoff Limit: MZFW + Takeoff Fuel = 164,600 lbs
  • Master Weight Summary & Regulatory Comparison Table

Weight Classification Abbr. Structural vs Operational Definition and Included Elements Governing Federal Regulation

Basic Empty Weight BEW Structural Baseline Airframe, engines, fixed equipment, unusable fuel, and full operating fluids (oil/hydraulics). 14 CFR § 25.29

Operating Empty Weight OEW / DOW Operational Baseline BEW plus flight and cabin crew, crew baggage, catering, potable water, and emergency gear; excludes fuel and payload. 14 CFR § 121.695

Zero Fuel Weight ZFW Operational OEW plus total passenger, baggage, and cargo payload; excludes all usable fuel. 14 CFR § 121.695

Maximum Zero Fuel Weight MZFW Structural Maximum certified weight before usable fuel is loaded; protects wing root spars against excessive bending moment. 14 CFR § 25.341

Maximum Ramp Weight MRW / MTW Structural Maximum certified weight for ground taxi and pushback; covers ground maneuvering gear loads. 14 CFR § 25.1583

Maximum Takeoff Weight MTOW Structural Maximum certified weight at start of takeoff roll; airframe structural design limit. 14 CFR § 25.107

Performance Takeoff Weight PTOW Aerodynamic / Environmental Maximum takeoff weight permitted by runway length, obstacles, climb gradients, tire speed, and brake energy. 14 CFR §§ 121.189, 25.101

Maximum Landing Weight MLW Structural Maximum certified weight for touchdown; certified for 10 fps design sink rate. 14 CFR § 25.473

Performance Landing Weight PLW Aerodynamic / Runway Maximum landing weight permitted by destination runway length and approach climb gradient. 14 CFR §§ 121.195, 25.125

  • Common Dispatch Traps & Operational Pitfalls
  • Trap 1: Ramp Weight vs. Takeoff Weight Confusion

Novice dispatchers frequently confuse Ramp Weight with Takeoff Weight. If an aircraft's planned weight at the gate equals the structural MTOW, it will be under weight at takeoff after burning taxi fuel. Conversely, if the aircraft is fueled such that its weight equals the Maximum Ramp Weight, the crew must burn at least the planned taxi fuel allowance prior to brake release; if they receive an immediate intersection takeoff with zero taxi burn, they risk initiating takeoff above structural MTOW.

Trap 2: Overlooking Destination Landing Weight at Departure Release

A flight may be well below structural MTOW and performance MTOW at departure, but if the flight distance is short (e.g., a 45-minute flight burning only 3,500 lbs of fuel), the takeoff weight may cause the aircraft to arrive at destination well above Maximum Landing Weight (MLW) . Under 14 CFR § 121.195 , releasing a flight that will arrive overweight without fuel jettison or an emergency is a federal violation.

Trap 3: Adding Cargo When at MZFW

When an aircraft's planned payload brings it exactly to its Maximum Zero Fuel Weight (MZFW), the station agent may ask dispatch if 1,000 lbs of late cargo can be added since total aircraft weight is still 20,000 lbs below MTOW. The dispatcher must refuse . Because all payload goes into the fuselage, adding any weight to an aircraft at MZFW directly violates the wing root bending structural limit, regardless of how much margin remains below MTOW.

Loading diagram... Dispatch Weight Determination & MATOW Constraint Flow