Study guide

7.2 Structural & Induction Icing

FAA ADX Aircraft Dispatcher Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Regulations & Dispatcher Certification (14 CFR Part 65)

1.1 14 CFR Part 65 Eligibility, Privileges, Limitations & Retesting 1.2 Operational Control & Shared Dispatcher-PIC Responsibility 1.3 Dispatch Release Requirements, Amendments & Records

2 Chapter 2: Part 121 Domestic, Flag & Supplemental Operating Rules

2.1 Domestic vs. Flag vs. Supplemental Operational Rules 2.2 Dispatch Weather Minimums & Departure Rules 2.3 Takeoff Alternates & Clean Aircraft Concept

3 Chapter 3: Destination Alternates, Alternate Minimums & Redispatch

3.1 Destination Alternate Requirements (1-2-3 Rule & Flag/Supplemental) 3.2 Alternate Airport Weather Minimums (OpSpecs Table C055) 3.3 Marginal Weather Rule & Second Alternate Selection 3.4 En Route Redispatch & Reclearance Procedures

4 Chapter 4: Dispatcher & Flightcrew Duty Limitations and Rest (14 CFR § 121.465 & Part 117)

4.1 Dispatcher Duty Time Limitations & Rest Requirements 4.2 Flightcrew Duty & Rest Requirements (14 CFR Part 117) 4.3 Dispatcher Qualifications, Recurrent Training & Operating Familiarization

5 Chapter 5: Minimum Equipment Lists (MEL), CDL & Maintenance Dispatch

5.1 Master Minimum Equipment List (MMEL) & Operator MEL 5.2 Configuration Deviation List (CDL) & Missing Secondary Airframe Parts 5.3 Dispatch with Inoperative Equipment, Logbooks & Special Flight Permits

6 Chapter 6: Aviation Meteorology — Atmosphere, Pressure Systems & Fronts

6.1 Atmospheric Structure, Pressure Systems & Altimetry 6.2 Air Masses & Frontal Systems 6.3 Clouds, Atmospheric Stability & Fog 6.4 Earth Motion, Global Circulation & Regional/Local Weather Regimes

7 Chapter 7: Hazardous Aviation Weather — Convection, Icing & Turbulence

7.1 Thunderstorms & Severe Convection 7.2 Structural & Induction Icing 7.3 Turbulence, Jet Streams & Clear Air Turbulence (CAT) 7.4 Low-Level Windshear & Microburst Detection Systems

8 Chapter 8: Aviation Weather Products, Observations & Forecasts

8.1 Surface Weather Observations (METAR & SPECI) 8.2 Terminal Aerodrome Forecasts (TAF) 8.3 In-Flight Weather Advisories (PIREPs, AIRMETs, SIGMETs) 8.4 Upper-Air Analysis & Prognostic Weather Charts

9 Chapter 9: Airspace Structure, Air Traffic Control & Traffic Management

9.1 Airspace Classes & Operating Rules 9.2 Special Use Airspace & Temporary Flight Restrictions 9.3 Air Traffic Control Flow Management & Initiatives 9.4 NOTAM System & Airport Field Condition Reporting 9.5 Flight Plan Filing: Domestic and International (ICAO) Flight Plans

10 Chapter 10: IFR Navigation, Airway Structure & Charting

10.1 Ground-Based Navigation Facilities (VOR, TACAN, DME, ILS) 10.2 RNAV, RNP & Performance-Based Navigation (PBN) 10.3 En Route IFR Charts & High/Low Airway Navigation 10.4 Earth Reference, Time Standards, Chart Projections & Great-Circle Navigation

11 Chapter 11: Terminal Instrument Procedures — SIDs, STARs & Approaches

11.1 Standard Instrument Departures (SIDs) & Obstacle Departure Procedures (ODPs) 11.2 Standard Terminal Arrival Routes (STARs) & En Route Transitions 11.3 Instrument Approach Procedures & Minimums 11.4 Holding Procedures & Holding Pattern Calculations

12 Chapter 12: High-Altitude Transonic Aerodynamics & Jet Characteristics

12.1 Transonic Flow, Mach Number & Compressibility 12.2 Shock Waves, Mach Tuck & Shock Stall 12.3 Coffin Corner, Buffet Boundaries & Swept-Wing Aerodynamics

13 Chapter 13: Transport Category Turbine Aircraft Systems

13.1 Turbine Powerplants & Auxiliary Power Units 13.2 Electrical, Hydraulic & Pneumatic Systems 13.3 Pressurization, Environmental Control & Oxygen Systems 13.4 Flight Management Systems (FMS), Autoflight & Avionics

14 Chapter 14: Aircraft Weight, Balance & Loading

14.1 Weight Definitions & Structural Limitations 14.2 Center of Gravity (CG) Principles & Computations 14.3 Cargo Loading, Floor Load Limits & Load Manifests

15 Chapter 15: Transport Category Aircraft Performance & Limitations

15.1 Takeoff Performance & V-Speeds 15.2 Climb Gradients, Obstacle Clearance & Runway Limitations 15.3 En Route Engine Inoperative Performance & Drift-Down 15.4 Landing Performance & Runway Condition Assessment

16 Chapter 16: Practical Dispatch Flight Planning, Fuel Strategy & Emergencies

16.1 Domestic, Flag & Supplemental Fuel Requirements 16.2 Flight Planning, Route Selection & Equal Time Point (ETP) / PNR 16.3 Emergency Procedures, In-Flight Diversions & Security Threats 16.4 NTSB Part 830 Incident & Accident Notification Procedures 16.5 Flight Following, Overdue Aircraft & Post-Flight Duties

17 Chapter 17: Human Factors, ADM, CRM & Dispatch Communications

17.1 Human Factors & Human Error in Airline Dispatch 17.2 Aeronautical Decision Making, Judgment & Risk Management 17.3 Crew Resource Management, Dispatch Teamwork & Briefing Technique 17.4 Dispatch Communications, Data Link & Aeronautical Publications

7.2 Structural & Induction Icing

Key Takeaways Explain This Topic AI

Structural icing strictly requires two simultaneous conditions: visible moisture (clouds, fog, rain, or drizzle) and an airframe surface temperature at or below 0°C, with the most severe accretion occurring between 0°C and -10°C.

Rime ice forms when small supercooled droplets freeze instantaneously into an opaque, milky, granular deposit along leading edges; Clear ice forms when large droplets freeze slowly as they flow backward, creating a dense, heavy, transparent glaze with extreme surface roughness and high adhesion.

Supercooled Large Droplets (SLD)—encountered in freezing drizzle (FZDZ) and freezing rain (FZRA)—strike beyond heated leading edges and pneumatic deicing boots, accreting as hazardous ridges on unprotected surfaces that induce roll upsets and aileron snatch.

Aerodynamic penalties of structural ice are severe, causing up to a 30% reduction in maximum coefficient of lift (CL_max), a 40% or greater increase in parasitic drag, an elevated stall speed, and a sharp drop in critical angle of attack.

Ice Contaminated Tailplane Stall (ICTS) occurs when flap extension increases wing downwash onto an iced horizontal stabilizer, driving it past its negative stall angle of attack and causing violent, uncommanded nose-down pitch; recovery requires immediately retracting flaps and applying back pressure—the direct opposite of wing stall recovery.

Last updated: September 2026

7.2 Structural & Induction Icing

Quick Summary: In-flight structural icing is one of the deadliest meteorological hazards confronting air carrier operations. It requires two concurrent physical conditions: visible moisture (clouds, fog, rain) and an airframe surface temperature at or below 0°C . Ice accretion occurs primarily between 0°C and -20°C , with maximum severity concentrated between 0°C and -10°C . Ice is classified into Clear (large droplets, slow freezing, transparent, dense, most hazardous), Rime (small droplets, instantaneous freezing, milky-white, granular), and Mixed . Supercooled Large Droplets (SLD) present in freezing rain (FZRA) and freezing drizzle (FZDZ) flow aft beyond heated leading edges and deice boots, forming spanwise ridges that induce uncommanded roll upsets. Structural ice can reduce maximum lift by up to 30% , increase drag by over 40% , and elevate stall speeds. An Ice Contaminated Tailplane Stall (ICTS) induces a violent, uncommanded nose-down pitch upon flap extension, requiring immediate flap retraction and aft control column pressure—the exact opposite of a wing stall recovery.

1. Physics of Structural Icing

Structural icing does not occur simply because the outside air temperature is cold. It requires the physical impingement of liquid water droplets onto an airframe whose skin temperature is at or below freezing:

Supercooled Liquid Water (SLW)

Pure water in the free atmosphere does not freeze automatically at 0°C. For liquid water to transition into ice, it requires microscopic freezing nuclei (dust particles, mineral grains, or bacteria). In the clean upper atmosphere, freezing nuclei are scarce. Consequently, liquid water droplets remain in a metastable, liquid state at temperatures far below freezing—down to -40°C (the homogeneous nucleation point). These droplets are known as Supercooled Liquid Water (SLW) . When an aircraft strikes an SLW droplet, the mechanical impact provides the necessary shock to initiate instantaneous crystallization.

Total Air Temperature (TAT) vs. Static Air Temperature (SAT)

At high transport jet cruise speeds, aerodynamic compression of air molecules against the airframe produces ram rise , heating the leading edges: TAT = SAT × ( 1 + 0.2 × K × M 2 ) \text{TAT} = \text{SAT} \times \left(1 + 0.2 \times K \times M^2\right) TAT = SAT × ( 1 + 0.2 × K × M 2 )

(where M is Mach number and K is the recovery factor, roughly 0.85–1.0)

At Mach 0.80, ram rise warms the leading edges by approximately +25°C to +30°C above the ambient Static Air Temperature (SAT). Therefore, a jet cruising at FL 350 where SAT is -45°C experiences a TAT of roughly -18°C. Structural icing can occur only when Total Air Temperature (TAT) is at or below 0°C .

2. Temperature Regimes & Ice Classifications +-----------------------------------------------------------------------------------------+

  • | STRUCTURAL ICING CLASSIFICATION & CHARACTERISTICS |
  • +-------------+----------------+---------------+-------------------+----------------------+
  • | Ice Type | Temp Range | Droplet Size | Physical Structure| Aerodynamic Penalty |
  • +-------------+----------------+---------------+-------------------+----------------------+
  • | Clear | 0°C to -10°C | Large SLW | Transparent glaze;| Severe: Disrupts |
  • | (Glaze) | | droplets | smooth flow aft; | airflow, heavy weight|
  • | | | (cumuliform) | strong adhesion | high drag, hard break|
  • +-------------+----------------+---------------+-------------------+----------------------+
  • | Mixed | -10°C to -15°C | Mixed droplet | Rough, irregular, | High: Very rough |
  • | | | sizes | milky and clear | surface texture |
  • | | | | layers; mushroom | induces early stall |
  • +-------------+----------------+---------------+-------------------+----------------------+
  • | Rime | -15°C to -20°C | Small SLW | Milky-white, | Moderate: Changes |
  • | | | droplets | opaque, brittle, | airfoil camber; |
  • | | | (stratiform) | traps air bubbles | easily deiced |
  • +-------------+----------------+---------------+-------------------+----------------------+
  • | Glaciated | Below -20°C | Ice crystals | Dry crystals; | Low structural risk; |
  • | (Crystals) | (to -40°C) | (no liquid) | bounce off skin | core engine ice (ICI)|
  • +-------------+----------------+---------------+-------------------+----------------------+
  • 1. Clear Ice (Glaze Ice)

Environmental Occurrence : Temperatures between 0°C and -10°C in areas of high liquid water content (LWC) and large droplet sizes—typically in convective clouds (cumulus, cumulonimbus) or in freezing rain (FZRA).

Physical Process : When a large droplet strikes the leading edge, only a fraction of the droplet freezes instantaneously. The release of latent heat of fusion (80 calories per gram) warms the remaining liquid, retarding complete freezing. The unfrozen liquid flows backward along the chord of the airfoil before freezing solid.

Characteristics : Dense, transparent, glass-like coating. It forms horn-like projections along the leading edge that severely destroy laminar flow. It adheres tenaciously to the airframe, adds immense weight, and is exceptionally difficult for deicing boots to shed.

2. Rime Ice

Environmental Occurrence : Temperatures between -15°C and -20°C (and down to -30°C in stratiform clouds) with low liquid water content and small droplet sizes.

Physical Process : Because the ambient air is cold and droplets are small, the latent heat of fusion is rapidly dissipated. The entire droplet freezes instantaneously upon impact, trapping tiny air bubbles within the ice matrix.

Characteristics : Milky-white, opaque, brittle, granular appearance with a rough, sandpaper-like surface. It accretes primarily along the stagnation line of leading edges, antennas, and probes. Because of trapped air, it has low density and is relatively brittle, making it easier to fracture and remove using pneumatic deicing boots.

3. Mixed Ice

Forms at intermediate temperatures ( -10°C to -15°C ) where droplets of varying sizes collide simultaneously. Clear and rime ice intermingle, forming an irregular, mushroom-shaped accretion along leading edges that combines the tenacious adhesion of clear ice with the extreme surface roughness of rime ice.

3. Supercooled Large Droplets (SLD) & Runback Icing

Supercooled Large Droplets (SLD) are droplets of liquid water with diameters greater than 50 micrometers. SLDs occur in two distinct operational regimes:

Freezing Drizzle (FZDZ) : Droplet diameters between 100 and 500 micrometers .

Freezing Rain (FZRA) : Droplet diameters greater than 500 micrometers (up to several millimeters). SUPERCOOLED LARGE DROPLET (SLD) RUNBACK DANGER

  • Protected Heated Slat / Boot Unprotected Upper Wing Surface
  • / / \
  • ===[ Deice Boot Area ]===========[ Aft Ice Ridge Accretion ]============
  • \ \ /
  • Droplets strike & flow aft Disrupts airflow over ailerons;

Induces uncommanded roll upset!

The Fatal Physics of SLD

Conventional aircraft ice protection systems (pneumatic boots and thermal bleed air slats) are certified under 14 CFR Part 25 Appendix C , which historically only accounted for droplet sizes up to 50 microns. SLD droplets possess substantial mass and kinetic momentum.

When an SLD droplet strikes an airfoil:

Instead of freezing on the protected leading-edge boot or heated slat, the droplet splashes and flows chordwise aft beyond the protected surface .

The water freezes on the unprotected upper and lower surfaces of the wing, forming a spanwise ridge of ice immediately ahead of the ailerons.

This aft ridge creates severe boundary layer separation, generating an aerodynamic suction peak that violently deflects the ailerons to full deflection—known as aileron snatch —causing an unrecoverable roll upset (the root cause of the 1994 ATR 72 crash at Roselawn, Indiana).

4. Aerodynamic Penalties & Handling Hazards

Even imperceptible amounts of structural ice cause catastrophic aerodynamic degradation:

Lift Reduction : Maximum coefficient of lift ( C L , max ⁡ C_{L,\max} C L , m a x ​ ) decreases by up to 30% . Ice roughness trips the laminar boundary layer into turbulent flow, triggering premature boundary layer separation at lower angles of attack.

Drag Increase : Total parasitic drag increases by 40% to 100% or more . Cruising aircraft may find engine thrust insufficient to maintain altitude, resulting in an uncommanded drift-down.

Stall Speed Elevation : Stall speed ( V s V_s V s ​ ) increases by 10 to 20 knots or more . An aircraft on approach flying at normal clean reference speeds may suddenly stall without warning.

Critical Angle of Attack Reduction : The wing's stall angle of attack drops precipitously from normal values of 16°–18° down to 8°–10° . Conventional stall warning vanes and stick shakers, calibrated for clean wings, may fail to trigger before the aircraft stalls.

Wing Stall vs. Ice Contaminated Tailplane Stall (ICTS)

  • Parameter Wing Stall (Classic) Tailplane Stall (ICTS)
  • Aerodynamic Surface Main Wing (generates UPWARD lift) Horizontal Stabilizer (generates DOWNWARD lift)

Triggering Event High angle of attack, slow airspeed, high G-load Flap extension (increases wing downwash onto tail)

Pitch Behavior Nose pitches DOWN (loss of wing lift) Violent, uncommanded nose DOWN (loss of tail downforce)

Control Column Feel Mushy, buffeting, light back pressure Violent forward snatch ; forward control column force

Immediate Flap Action Maintain or adjust per normal stall recovery IMMEDIATELY RETRACT FLAPS to previous detent

  • Control Column Action PUSH FORWARD to reduce wing AOA PULL BACK FIRMLY to reduce tailplane negative AOA
  • Thrust Action Advance thrust to maximum Adjust cautiously; nose-down pitch trim must be resisted

Warning

Critical ADX Exam Distinction : In an Ice Contaminated Tailplane Stall (ICTS) , extending flaps directs high-speed downward air (downwash) onto the horizontal stabilizer, pushing the tail beyond its negative stall angle of attack. The tail loses downward lift, causing the nose to pitch violently down. Applying classic wing stall recovery (pushing forward) will accelerate the dive straight into the ground! The flight crew must retract flaps immediately and pull back firmly on the control column.

Loading diagram... Wing Stall vs. Ice Contaminated Tailplane Stall (ICTS) Aerodynamics & Recovery