Study guide

10.4 Earth Reference, Time Standards, Chart Projections & Great-Circle Navigation

FAA ADX Aircraft Dispatcher Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Regulations & Dispatcher Certification (14 CFR Part 65)

1.1 14 CFR Part 65 Eligibility, Privileges, Limitations & Retesting 1.2 Operational Control & Shared Dispatcher-PIC Responsibility 1.3 Dispatch Release Requirements, Amendments & Records

2 Chapter 2: Part 121 Domestic, Flag & Supplemental Operating Rules

2.1 Domestic vs. Flag vs. Supplemental Operational Rules 2.2 Dispatch Weather Minimums & Departure Rules 2.3 Takeoff Alternates & Clean Aircraft Concept

3 Chapter 3: Destination Alternates, Alternate Minimums & Redispatch

3.1 Destination Alternate Requirements (1-2-3 Rule & Flag/Supplemental) 3.2 Alternate Airport Weather Minimums (OpSpecs Table C055) 3.3 Marginal Weather Rule & Second Alternate Selection 3.4 En Route Redispatch & Reclearance Procedures

4 Chapter 4: Dispatcher & Flightcrew Duty Limitations and Rest (14 CFR § 121.465 & Part 117)

4.1 Dispatcher Duty Time Limitations & Rest Requirements 4.2 Flightcrew Duty & Rest Requirements (14 CFR Part 117) 4.3 Dispatcher Qualifications, Recurrent Training & Operating Familiarization

5 Chapter 5: Minimum Equipment Lists (MEL), CDL & Maintenance Dispatch

5.1 Master Minimum Equipment List (MMEL) & Operator MEL 5.2 Configuration Deviation List (CDL) & Missing Secondary Airframe Parts 5.3 Dispatch with Inoperative Equipment, Logbooks & Special Flight Permits

6 Chapter 6: Aviation Meteorology — Atmosphere, Pressure Systems & Fronts

6.1 Atmospheric Structure, Pressure Systems & Altimetry 6.2 Air Masses & Frontal Systems 6.3 Clouds, Atmospheric Stability & Fog 6.4 Earth Motion, Global Circulation & Regional/Local Weather Regimes

7 Chapter 7: Hazardous Aviation Weather — Convection, Icing & Turbulence

7.1 Thunderstorms & Severe Convection 7.2 Structural & Induction Icing 7.3 Turbulence, Jet Streams & Clear Air Turbulence (CAT) 7.4 Low-Level Windshear & Microburst Detection Systems

8 Chapter 8: Aviation Weather Products, Observations & Forecasts

8.1 Surface Weather Observations (METAR & SPECI) 8.2 Terminal Aerodrome Forecasts (TAF) 8.3 In-Flight Weather Advisories (PIREPs, AIRMETs, SIGMETs) 8.4 Upper-Air Analysis & Prognostic Weather Charts

9 Chapter 9: Airspace Structure, Air Traffic Control & Traffic Management

9.1 Airspace Classes & Operating Rules 9.2 Special Use Airspace & Temporary Flight Restrictions 9.3 Air Traffic Control Flow Management & Initiatives 9.4 NOTAM System & Airport Field Condition Reporting 9.5 Flight Plan Filing: Domestic and International (ICAO) Flight Plans

10 Chapter 10: IFR Navigation, Airway Structure & Charting

10.1 Ground-Based Navigation Facilities (VOR, TACAN, DME, ILS) 10.2 RNAV, RNP & Performance-Based Navigation (PBN) 10.3 En Route IFR Charts & High/Low Airway Navigation 10.4 Earth Reference, Time Standards, Chart Projections & Great-Circle Navigation

11 Chapter 11: Terminal Instrument Procedures — SIDs, STARs & Approaches

11.1 Standard Instrument Departures (SIDs) & Obstacle Departure Procedures (ODPs) 11.2 Standard Terminal Arrival Routes (STARs) & En Route Transitions 11.3 Instrument Approach Procedures & Minimums 11.4 Holding Procedures & Holding Pattern Calculations

12 Chapter 12: High-Altitude Transonic Aerodynamics & Jet Characteristics

12.1 Transonic Flow, Mach Number & Compressibility 12.2 Shock Waves, Mach Tuck & Shock Stall 12.3 Coffin Corner, Buffet Boundaries & Swept-Wing Aerodynamics

13 Chapter 13: Transport Category Turbine Aircraft Systems

13.1 Turbine Powerplants & Auxiliary Power Units 13.2 Electrical, Hydraulic & Pneumatic Systems 13.3 Pressurization, Environmental Control & Oxygen Systems 13.4 Flight Management Systems (FMS), Autoflight & Avionics

14 Chapter 14: Aircraft Weight, Balance & Loading

14.1 Weight Definitions & Structural Limitations 14.2 Center of Gravity (CG) Principles & Computations 14.3 Cargo Loading, Floor Load Limits & Load Manifests

15 Chapter 15: Transport Category Aircraft Performance & Limitations

15.1 Takeoff Performance & V-Speeds 15.2 Climb Gradients, Obstacle Clearance & Runway Limitations 15.3 En Route Engine Inoperative Performance & Drift-Down 15.4 Landing Performance & Runway Condition Assessment

16 Chapter 16: Practical Dispatch Flight Planning, Fuel Strategy & Emergencies

16.1 Domestic, Flag & Supplemental Fuel Requirements 16.2 Flight Planning, Route Selection & Equal Time Point (ETP) / PNR 16.3 Emergency Procedures, In-Flight Diversions & Security Threats 16.4 NTSB Part 830 Incident & Accident Notification Procedures 16.5 Flight Following, Overdue Aircraft & Post-Flight Duties

17 Chapter 17: Human Factors, ADM, CRM & Dispatch Communications

17.1 Human Factors & Human Error in Airline Dispatch 17.2 Aeronautical Decision Making, Judgment & Risk Management 17.3 Crew Resource Management, Dispatch Teamwork & Briefing Technique 17.4 Dispatch Communications, Data Link & Aeronautical Publications

10.4 Earth Reference, Time Standards, Chart Projections & Great-Circle Navigation

Key Takeaways Explain This Topic AI

One minute of latitude equals one nautical mile everywhere on the globe, which is why latitude is the universal distance scale on a navigation chart while longitude spacing shrinks toward the poles.

A great circle is the shortest distance between two points on the Earth but requires a continuously changing true course; a rhumb line holds a constant course but is longer, and the difference grows with latitude and east-west distance.

FAA en route and sectional charts use the Lambert conformal conic projection, on which a straight line closely approximates a great circle; a Mercator projection is the opposite, plotting rhumb lines as straight lines and great circles as curves.

All aviation weather products, NOTAMs, flight plans, dispatch releases, and ATC clearances use Coordinated Universal Time (UTC, spoken as Zulu), and a date-of-flight error at the International Date Line is a recurring dispatch trap.

Magnetic variation is the angular difference between true and magnetic north, shown by isogonic lines with the zero-variation agonic line; near the magnetic poles the compass becomes unreliable, which is why high-latitude operations use true or grid heading references.

Last updated: September 2026

10.4 Earth Reference, Time Standards, Chart Projections & Great-Circle Navigation

Part 65 Appendix A, section III.A opens the navigation curriculum with the Study of the Earth: time reference, definitions, projections, and charts . It is the foundation the rest of Chapter 10 assumes. A dispatcher who is fuzzy on great circles will not understand why a computerized flight plan routes a Chicago-to-Tokyo flight over the Aleutians, and a dispatcher who is fuzzy on UTC will eventually release a flight against the wrong day's forecast.

1. The Coordinate Framework and the Nautical Mile

Term Definition Why the dispatcher cares

Latitude Angular distance north or south of the equator, 0 to 90 degrees. Parallels of latitude are all parallel and equally spaced One minute of latitude = one nautical mile , everywhere. Latitude is the universal distance scale

Longitude Angular distance east or west of the Prime Meridian at Greenwich, 0 to 180 degrees. Meridians run pole to pole Meridians converge toward the poles, so one minute of longitude equals one nautical mile only at the equator and shrinks to zero at the poles

Nautical mile (NM) 6,076 feet, or 1,852 metres The unit of every en route distance, alternate distance, and ETOPS radius in this guide

Statute mile (SM) 5,280 feet The unit of visibility in U.S. weather reports and approach minimums — never of distance

Warning

Exam trap — the two miles. Runway visual range is in feet and prevailing visibility is in statute miles, while every navigation distance is in nautical miles. One nautical mile is about 1.15 statute miles. Mixing them in an alternate-distance or fuel problem is a classic ADX error.

Convergence of the meridians is the single geometric fact behind most of this section. Because meridians converge, a line of constant true course is not the shortest path, chart projections must distort something, and a magnetic heading reference becomes useless near the poles.

2. Great Circle vs. Rhumb Line

Great circle Rhumb line (loxodrome)

Definition The arc formed where a plane through the center of the Earth intersects the surface A line crossing every meridian at the same angle

Distance Shortest possible between two points Longer , and increasingly so with latitude and east-west separation

Course Changes continuously (except along the equator or a meridian) Constant

Use Long-range flight planning, oceanic and polar routing, FMS legs Short legs, plotting charts, manual dead reckoning

The practical consequence is the one dispatchers must be able to defend to a passenger or a new hire: a great-circle route between two points at the same northern latitude bows poleward . Chicago to Tokyo, both near 40 degrees north, is shortest via the Aleutians and the Bering Sea, not straight west along the 40th parallel. On a transatlantic sector the great circle arcs north through Canadian and Greenlandic airspace. Every NAT organized track and every FMS direct leg is built on great-circle geometry , which is also why the true course changes at each waypoint even when the aircraft has not turned.

Because meridians converge, conversion angle (half the convergency) is the difference between the great-circle course and the rhumb-line course between two points — it is zero at the equator and grows with latitude.

3. Chart Projections

Every flat map of a curved Earth distorts something. The only question is what it preserves.

Projection What it preserves Great circle appears as Rhumb line appears as Where you see it

Lambert conformal conic Angles and shapes locally; scale nearly constant across the chart Approximately a straight line A curve FAA en route low and high altitude charts, sectionals, and terminal charts

Mercator (cylindrical) Angles; but area is grossly exaggerated toward the poles A curve A straight line Marine charts and some oceanic plotting charts

Polar stereographic / grid Usable geometry at high latitude where the others fail Close to a straight line near the pole Not useful Polar route plotting charts

Why the FAA uses Lambert conformal conic: a straight line drawn between two points on a Lambert chart is, for practical purposes, a great circle, so a dispatcher can measure a route directly off the chart and get the short path. Its constant scale also means distances measured anywhere on the sheet are comparable. Mercator does the opposite — it is superb for holding a constant course and terrible for judging distance or area at high latitude, which is why Greenland looks the size of Africa on one.

4. Time Reference

Aviation runs on a single clock. Coordinated Universal Time (UTC) , spoken as "Zulu" and written with a trailing Z , is the time reference for:

  • METARs, SPECIs, TAFs, SIGMETs, AIRMETs, and every prognostic chart;
  • NOTAMs, including start and end times;
  • ICAO and domestic flight plans, including estimated off-block time and total estimated elapsed time;
  • The dispatch release, the flight plan, and ATC clearances;

ETOPS entry points, track messages, and oceanic clearances.

Practical rules a dispatcher must hold:

Convert in one direction only, and write the Z. A release with a local time on it is an error waiting to happen.

The date changes at 0000Z , not at local midnight. A 2300Z departure on the 14th and a 0130Z arrival are on different UTC dates , and a TAF valid 1500/1524 covers a specific UTC day. Selecting the wrong day's TAF is a genuine and recurring dispatch error.

The International Date Line near 180 degrees longitude shifts the calendar date , not the UTC clock. A westbound Pacific crossing loses a calendar day and an eastbound crossing gains one, which affects crew scheduling, curfews, slot times, and the date-of-flight field on an ICAO flight plan.

The Earth rotates 15 degrees of longitude per hour , which is the mental arithmetic behind time-zone conversion and sunrise/sunset estimation for a route.

5. Magnetic Variation, Isogonic Lines, and Grid Navigation

  • Term Definition
  • True north The geographic North Pole; the reference for latitude and longitude and for great-circle courses
  • Magnetic north The direction a compass points, toward the magnetic pole, which moves over time

Magnetic variation The angular difference between true and magnetic north at a location. East variation is subtracted from true to get magnetic; west variation is added

Isogonic lines Chart lines connecting points of equal magnetic variation

Agonic line The line of zero variation , where true and magnetic north are aligned from the observer's position

Magnetic dip The vertical component of the Earth's magnetic field, which increases toward the magnetic poles and degrades compass usability

U.S. airways, runway numbers, VOR radials, and ATC headings are all referenced to magnetic north, which is why the FAA periodically renumbers runways and recalibrates VOR radials as variation drifts. Oceanic and polar tracks, by contrast, are published in true or grid courses , because near the magnetic pole variation changes enormously over a short distance and magnetic dip makes a compass unreliable. Section 10.3 covers the resulting true versus magnetic and grid heading procedures used above roughly 70 degrees north.

Common ADX Exam Traps

Assuming the shortest route is the one that looks straight on a Mercator. On a Mercator, the straight line is the rhumb line and it is longer.

Using one minute of longitude as one nautical mile. That holds only at the equator.

Mixing statute and nautical miles. Visibility is statute; navigation is nautical.

Reading a TAF from the wrong UTC day. The UTC date changes at 0000Z, not local midnight.

Applying variation the wrong way. East is least (subtract from true), west is best (add to true).

Loading diagram... Earth Reference Framework: Distance, Course, Projection, and Time